[PATCH 05/12] i2c: pxa: Add bus reset functionality

[vaibhav.hiremath@linaro.org (Vaibhav Hiremath)]

On Friday 29 May 2015 07:29 PM, Rob Herring wrote:
> On Thu, May 28, 2015 at 8:03 AM, Vaibhav Hiremath
> <vaibhav.hiremath@linaro.org> wrote:
>> From: Rob Herring <robh@kernel.org>
>
> This probably should still be Leilei, but...
>

Ok, Since I am taking forward from your sign-off, did not change it.
Anyway will fix in next version.

>> Since there is some problematic i2c slave devices on some
>> platforms such as dkb (sometimes), it will drop down sda
>> and make i2c bus hang, at that time, it need to config
>> scl/sda into gpio to simulate "stop" sequence to recover
>> i2c bus, so add this interface.
>>
>> Signed-off-by: Leilei Shang <shangll@marvell.com>
>> Signed-off-by: Rob Herring <robh@kernel.org>
>> [vaibhav.hiremath at linaro.org: Updated Changelog]
>> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
>>
>> Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
>> ---
>>   drivers/i2c/busses/i2c-pxa.c | 90 ++++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 90 insertions(+)
>>
>> diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c
>> index 8ca5552..eb09071 100644
>> --- a/drivers/i2c/busses/i2c-pxa.c
>> +++ b/drivers/i2c/busses/i2c-pxa.c
>> @@ -37,6 +37,8 @@
>>   #include <linux/slab.h>
>>   #include <linux/io.h>
>>   #include <linux/i2c/pxa-i2c.h>
>> +#include <linux/of_gpio.h>
>> +#include <linux/pinctrl/consumer.h>
>>
>>   #include <asm/irq.h>
>>
>> @@ -177,6 +179,9 @@ struct pxa_i2c {
>>          bool                    highmode_enter;
>>          unsigned int            ilcr;
>>          unsigned int            iwcr;
>> +       struct pinctrl          *pinctrl;
>> +       struct pinctrl_state    *pin_i2c;
>> +       struct pinctrl_state    *pin_gpio;
>>   };
>>
>>   #define _IBMR(i2c)     ((i2c)->reg_ibmr)
>> @@ -269,6 +274,62 @@ static void i2c_pxa_show_state(struct pxa_i2c *i2c, int lno, const char *fname)
>>
>>   #define show_state(i2c) i2c_pxa_show_state(i2c, __LINE__, __func__)
>>
>> +static void i2c_bus_reset(struct pxa_i2c *i2c)
>
> There's a generic mechanism in i2c_generic_gpio_recovery we should use
> here. It appears to be similar, but not exactly the same. The pinctrl
> part should probably be done by gpio driver.
>


Good point.

As you mentioned, they are not exactly same.

But we can achieve exactly what we wanted using prepare & unprepare
callbacks.
Generate stop signal in unprepare() callback should suffice our need.


But I am not quite sure about pinctrl handling by gpio driver.
I was tracing the calls from gpio_request_one()anf gpio_free()
but it seems they are not bringing back pins to default state.

correct me if I am wrong.

Thanks,
Vaibhav