[PATCH] ARM: dts: Add CPU cooling binding for Exynos3250-based Rinato/Monk board

[k.kozlowski@samsung.com (Krzysztof Kozlowski)]

On 02.07.2015 14:37, Chanwoo Choi wrote:
> This patch add the cooling device to control the overheating issue on
> Exynos3250-based Rinato/Monk board.
> 
> Cc: Kukjin Kim <kgene@kernel.org>
> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> Depends on:
> This patch needs the cpufreq support of Exynos3250 SoC. So, this patch has the
> dependency on patch[1] which support the generic cpufreq for Exynos3250 SoC.
> [1] https://lkml.org/lkml/2015/7/1/696
>     : [PATCH v6 0/3] cpufreq: Use cpufreq-dt driver for Exynos3250
> 
>  arch/arm/boot/dts/exynos3250-monk.dts   | 15 +++++++++++++++
>  arch/arm/boot/dts/exynos3250-rinato.dts | 15 +++++++++++++++
>  arch/arm/boot/dts/exynos3250.dtsi       |  1 +
>  3 files changed, 31 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
> index 7863265d4868..540a0adf2be6 100644
> --- a/arch/arm/boot/dts/exynos3250-monk.dts
> +++ b/arch/arm/boot/dts/exynos3250-monk.dts
> @@ -116,6 +116,21 @@
>  		min-microvolt = <1100000>;
>  		max-microvolt = <2700000>;
>  	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			cooling-maps {
> +				map0 {
> +					/* Correspond to 500MHz at freq_table */
> +					cooling-device = <&cpu0 5 5>;
> +				};
> +				map1 {
> +					/* Correspond to 200MHz at freq_table */
> +					cooling-device = <&cpu0 8 8>;
> +				};
> +			};
> +		};
> +	};
>  };
>  
>  &adc {
> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> index ddd7ac283045..0e62a6435e07 100644
> --- a/arch/arm/boot/dts/exynos3250-rinato.dts
> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> @@ -107,6 +107,21 @@
>  		min-microvolt = <1100000>;
>  		max-microvolt = <2700000>;
>  	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			cooling-maps {
> +				map0 {
> +					/* Corresponds to 500MHz */
> +					cooling-device = <&cpu0 5 5>;
> +				};
> +				map1 {
> +					/* Corresponds to 200MHz */
> +					cooling-device = <&cpu0 8 8>;
> +				};
> +			};
> +		};
> +	};
>  };
>  
>  &adc {
> diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
> index e0f3b2ed41a3..a4931b660ddb 100644
> --- a/arch/arm/boot/dts/exynos3250.dtsi
> +++ b/arch/arm/boot/dts/exynos3250.dtsi
> @@ -55,6 +55,7 @@
>  			clock-frequency = <1000000000>;
>  			clocks = <&cmu CLK_ARM_CLK>;
>  			clock-names = "cpu";
> +			#cooling-cells = <2>;
>  

Don't you need also cooling-{min,max}-state properties?

Best regards,
Krzysztof

>  			operating-points = <
>  				1000000 1150000
>