[PATCH 06/10] ARM: dts: am4372: Use "syscon-phy-power" instead of "ctrl-module" in USB PHY node

[rogerq@ti.com (Roger Quadros)]

On 04/08/15 18:30, Kishon Vijay Abraham I wrote:
> Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
> property from USB PHY device tree node.
> 
> Since "am43xx_control_usb2phy1" and "am43xx_control_usb2phy2"
> devicetree nodes are no longer used, remove it.
> 
> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Acked-by: Roger Quadros <rogerq@ti.com>

cheers,
-roger

> ---
>  arch/arm/boot/dts/am4372.dtsi |   16 ++--------------
>  1 file changed, 2 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
> index ade28c79..24fa073 100644
> --- a/arch/arm/boot/dts/am4372.dtsi
> +++ b/arch/arm/boot/dts/am4372.dtsi
> @@ -802,18 +802,6 @@
>  			status = "disabled";
>  		};
>  
> -		am43xx_control_usb2phy1: control-phy at 44e10620 {
> -			compatible = "ti,control-phy-usb2-am437";
> -			reg = <0x44e10620 0x4>;
> -			reg-names = "power";
> -		};
> -
> -		am43xx_control_usb2phy2: control-phy at 0x44e10628 {
> -			compatible = "ti,control-phy-usb2-am437";
> -			reg = <0x44e10628 0x4>;
> -			reg-names = "power";
> -		};
> -
>  		ocp2scp0: ocp2scp at 483a8000 {
>  			compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
>  			#address-cells = <1>;
> @@ -824,7 +812,7 @@
>  			usb2_phy1: phy at 483a8000 {
>  				compatible = "ti,am437x-usb2";
>  				reg = <0x483a8000 0x8000>;
> -				ctrl-module = <&am43xx_control_usb2phy1>;
> +				syscon-phy-power = <&scm_conf 0x620>;
>  				clocks = <&usb_phy0_always_on_clk32k>,
>  					 <&usb_otg_ss0_refclk960m>;
>  				clock-names = "wkupclk", "refclk";
> @@ -843,7 +831,7 @@
>  			usb2_phy2: phy at 483e8000 {
>  				compatible = "ti,am437x-usb2";
>  				reg = <0x483e8000 0x8000>;
> -				ctrl-module = <&am43xx_control_usb2phy2>;
> +				syscon-phy-power = <&scm_conf 0x628>;
>  				clocks = <&usb_phy1_always_on_clk32k>,
>  					 <&usb_otg_ss1_refclk960m>;
>  				clock-names = "wkupclk", "refclk";
>