From mboxrd@z Thu Jan  1 00:00:00 1970
From: hdegoede@redhat.com (Hans de Goede)
Date: Thu, 6 Aug 2015 16:35:08 +0200
Subject: [linux-sunxi] [PATCH] musb: sunxi: Ignore VBus errors in
 host-only mode
In-Reply-To: <55C31963.2010701@schinagl.nl>
References: <1438723553-4136-1-git-send-email-hdegoede@redhat.com>
 <55C31963.2010701@schinagl.nl>
Message-ID: <55C3709C.4080609@redhat.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi,

On 06-08-15 10:22, Olliver Schinagl wrote:
> Hey Hans,
>
> I've tried getting your musb stuff working on a cubietruck, but i don't seem to see this patch on your linux-sunxi/sunxi-wip branch on github? Is your github branch fully functional at the moment?
>
> What I have done so far, is build the kernel using sunxi_defconfig and enabled USB_MUSB_SUNXI with its dependancies (musb isn't enabled there by default): USB_SUPPORT [=y] && USB_MUSB_HDRC [=y] && ARCH_SUNXI [=y] && NOP_USB_XCEIV [=y] && PHY_SUN4I_USB [=y] && EXTCON [=y] && GENERIC_PHY [=y]  Selects: SUNXI_SRAM [=y]
>
> I changed the dts from dr_mode='otg' to dr_mode='host', a) we only need host mode anyway (the id pin isn't properly connected)

If you change the dr_mode to host then you _must_ also remove any id_det and vbus_det
gpio settings from the usb_phy node in the dts, as the sun4i phy code detects
host vs otg mode by checking for the presence of these.

 > and b) I got an error about an known dr_mode before and this was the quick and easy way.
>
> Dmesg produces the following related to musb.
>
> [    1.691062] usb_phy_generic.0.auto supply vcc not found, using dummy regulator
> [    1.691445] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
> [    1.691453] musb-hdrc: MHDRC RTL version 0.0
> [    1.691467] musb-hdrc: 11/11 max ep, 5184/8192 memory
> [    1.691543] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
> [    1.691553] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 5
> [    1.692470] hub 5-0:1.0: USB hub found
> [    1.692529] hub 5-0:1.0: 1 port detected
> [    1.699956] sunxi-rtc 1c20d00.rtc: setting system clock to 2015-08-06 07:59:08 UTC (1438847948)
> [    1.704733] usb0-vbus: disabling
> [    1.765695] ldo4: disabling
> [    1.808351] ldo3: disabling
> [    1.848769] vcc5v0: disabling
> [    1.848774] vcc3v0: disabling
>
> The usb_phy_generic missing shouldn't be too bad? But the usb0-vbus being disabled obviously might be related to the musb port not working?

Correct.

For starters I would try the dts changes I suggested above.

Regards,

Hans