[PATCH 0/3] mmc: Wait for card_busy before starting sdio requests

[hdegoede@redhat.com (Hans de Goede)]

Hi,

On 24-09-15 18:04, Doug Anderson wrote:
> Hi,
>
> On Thu, Sep 24, 2015 at 2:19 AM, Hans de Goede <hdegoede@redhat.com> wrote:
>> Hi,
>>
>> On 23-09-15 23:43, Ulf Hansson wrote:
>>>
>>> On 22 September 2015 at 17:30, Hans de Goede <hdegoede@redhat.com> wrote:
>>>>
>>>> Hi Ulf,
>>>>
>>>> Here is a non RFC version of my patch-set to wait for card_busy before
>>>> starting sdio requests. It is the same as the RFC version of the set,
>>>> but this time it has been tested no hardware which actually needs this
>>>> and I can confirm now that this fixes wifi on that hardware.
>>>
>>>
>>> Great! Thanks, applied for next!
>>
>>
>> Great, thanks, I guess it is too late for this to go as a fix into
>> 4.3-rcX (no worries if it is) ?
>>
>>>> This patch-set should also allow removing this dw_mmc specific fix:
>>>>
>>>>
>>>> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/mmc/host/dw_mmc.c?id=0bdbd0e88cf6b603a2196418672715b0890fb040
>>>>
>>>> As this patch-set fixes this problem in a generic manner.
>>>
>>>
>>> Care to send a patch to remove the above hack/fix?
>>
>>
>> I do not have any hardware to test this.
>>
>> I've added Doug the original author of that patch to the Cc.
>>
>> Dough, can you test if with the patch set from this mail thread
>> (merged into mmc/next) this patch:
>>
>> https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/mmc/host/dw_mmc.c?id=0bdbd0e88cf6b603a2196418672715b0890fb040
>>
>> Is still necessary ? Since this patch-set fixes the same issue
>> in the mmc core I believe that this commit can be reverted now.
>
> I'll try to find some time in the next few days to test, but I'm not
> terribly hopeful we can just revert the patch because:
>
> 1. Only one of the two callers of dw_mci_wait_while_busy() is handled
> by your patch.  mci_send_cmd() is used internally in dw_mmc to throw
> something in the CMD register without going through the normal MMC
> path.  This is used exclusively to update the clock registers in
> dw_mmc.  I'm pretty sure this needs the wait, too.  It's always seemed
> weird / awkward to me that you need to use the CMD register to update
> clock settings in dw_mmc, but c'est la vie.

I would not expect the card to signal busy when trying to change clocks
though, so I do not think this will really be a problem.

> 2. If I remember correctly, we ran into other instances where non-SDIO
> cards needed the busy check.  It wasn't terribly common, but I think I
> ran into this when stress testing, but only on a few cards.

Hmm, that would be a problem yes.

> The patch referenced here only seems to check for SDIO commands.  As I
> understand it, to be correct, it should check for all data commands
> (other than stop or voltage change commands).

But that is not what the patch does, it actually waits for all commands,
including non data commands. An earlier attempt of mine to fix the sdio
wifi issues with the sunxi driver copied your approach, and I actually
got reports of regressions with using normal micro-sd memory cards
from several people testing that patch.

And if you're right that we should wait for all data commands, then
I wonder if this is a designware thing (I believe the allwinner
mmc controller is designware derived) or a generic mmc / sdio thing ?

> The Designware Databook
> makes no reference to only needing the wait for SDIO commands.

Yet your commit message references problems with sdio wifi cards, and
on sunxi we've only been seeing this problem with sdio wifi cards / sdio
commands.

> ...of course, it's always possible that some of the things I saw above
> will no longer happen with all the other fixes we've done in the
> meantime (turning on voltages at the right time, adding the right
> delays, etc).
>
>
> Note that I've hardly looked at sdhci at all, but on SDHCI is this
> handled by the "SDHCI_DATA_INHIBIT" bits?

Regards,

Hans