From mboxrd@z Thu Jan  1 00:00:00 1970
From: hanjun.guo@linaro.org (Hanjun Guo)
Date: Fri, 27 Nov 2015 21:28:31 +0800
Subject: [PATCH v2 0/4] ACPI based NUMA support for ARM64
In-Reply-To: <56582195.80306@huawei.com>
References: <1447784733-10419-1-git-send-email-gkulkarni@caviumnetworks.com>
 <56582195.80306@huawei.com>
Message-ID: <56585A7F.3010505@linaro.org>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On 11/27/2015 05:25 PM, Shannon Zhao wrote:
>
>
> On 2015/11/18 2:25, Ganapatrao Kulkarni wrote:
>>   -v2 rebased on arm64-numa v7 patches.
>>   http://www.spinics.net/lists/arm-kernel/msg460813.html
>>
>>   -v1 initial patches from Hanjun Guo
>>
>> Hanjun Guo (4):
>>    acpi, numa: Use pr_fmt() instead of printk
>>    acpi, numa: Replace ACPI_DEBUG_PRINT() with pr_debug()
>>    arm64, acpi, numa: NUMA support based on SRAT and SLIT
>>    acpi, numa: Enable ACPI based NUMA on ARM64
>>
>>   arch/arm64/include/asm/acpi.h |   4 +
>>   arch/arm64/kernel/Makefile    |   1 +
>>   arch/arm64/kernel/acpi_numa.c | 215 ++++++++++++++++++++++++++++++++++++++++++
>>   arch/arm64/mm/numa.c          |   7 +-
>>   drivers/acpi/Kconfig          |   4 +-
>>   drivers/acpi/numa.c           | 106 ++++++++++++---------
>>   include/linux/acpi.h          |  15 +++
>>   7 files changed, 306 insertions(+), 46 deletions(-)
>>   create mode 100644 arch/arm64/kernel/acpi_numa.c
>>
>
> I've tested this patch set on QEMU VM and guest prints below log:
>
> ACPI: NUMA: SRAT: PXM 0 -> MPIDR 0x0 -> Node 0 cpu 1
> ACPI: NUMA: SRAT: PXM 0 -> MPIDR 0x1 -> Node 0 cpu 2
> ACPI: NUMA: SRAT: PXM 1 -> MPIDR 0x2 -> Node 1 cpu 3
> ACPI: NUMA: SRAT: PXM 1 -> MPIDR 0x3 -> Node 1 cpu 4
> ACPI: NUMA: SRAT: Node 0 PXM 0 [mem 0x40000000-0x5fffffff]
> NUMA: Adding memblock [0x40000000 - 0x5fffffff] on node 0
> ACPI: NUMA: SRAT: Node 1 PXM 1 [mem 0x60000000-0x7fffffff]
> NUMA: Adding memblock [0x60000000 - 0x7fffffff] on node 1
> Initmem setup node 0 [mem 0x40000000-0x5fffffff]
>    NODE_DATA [mem 0x5fffe400-0x5fffffff]
> Initmem setup node 1 [mem 0x60000000-0x7fffffff]
>    NODE_DATA [mem 0x7effd400-0x7effefff]
> Zone ranges:
>    DMA      [mem 0x0000000040000000-0x000000007fffffff]
>    Normal   empty
> Movable zone start for each node
> Early memory node ranges
>    node   0: [mem 0x0000000040000000-0x000000005fffffff]
>    node   1: [mem 0x0000000060000000-0x000000007fffffff]
> Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
> Initmem setup node 1 [mem 0x0000000060000000-0x000000007fffffff]
>
> So, Tested-by: Shannon Zhao <shannon.zhao@linaro.org>

Hi Shannon, thanks a lot!

Thanks
Hanjun