* [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality
@ 2015-11-30 13:54 Jisheng Zhang
2015-12-06 9:28 ` Sebastian Hesselbarth
0 siblings, 1 reply; 5+ messages in thread
From: Jisheng Zhang @ 2015-11-30 13:54 UTC (permalink / raw)
To: linux-arm-kernel
The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
have gpios for card detection, write-protect, vqmmc and vmmc.
This patch adds pinmux for this sdcard interface, then adds regulators
for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
---
since v1:
- move sd1_pmux to soc dtsi
- remove cd-inverted and make cd-gpio GPIO_ACTIVE_LOW
arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 37 ++++++++++++++++++++++++++++--
arch/arm/boot/dts/berlin2q.dtsi | 5 ++++
2 files changed, 40 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
index cdcf89b..33b2875 100644
--- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
+++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
@@ -84,12 +84,45 @@
gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ reg_sdio1_vmmc: regulator at 3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "sdio1_vmmc";
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_sdio1_vqmmc: regulator at 4 {
+ compatible = "regulator-gpio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "sdio1_vqmmc";
+ regulator-type = "voltage";
+ enable-active-high;
+ gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
+ states = <3300000 0x1
+ 1800000 0x0>;
+ };
+ };
+};
+
+&soc_pinctrl {
+ sd1gpio_pmux: sd1pwr-pmux {
+ groups = "G23", "G32";
+ function = "gpio";
};
};
&sdhci1 {
- broken-cd;
- sdhci,wp-inverted;
+ vmmc-supply = <®_sdio1_vmmc>;
+ vqmmc-supply = <®_sdio1_vqmmc>;
+ cd-gpios = <&portc 30 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>;
+ pinctrl-names = "default";
status = "okay";
};
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 8ea177f..73a9362 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -417,6 +417,11 @@
soc_pinctrl: pin-controller {
compatible = "marvell,berlin2q-soc-pinctrl";
+ sd1_pmux: sd1-pmux {
+ groups = "G31";
+ function = "sd1";
+ };
+
twsi0_pmux: twsi0-pmux {
groups = "G6";
function = "twsi0";
--
2.6.2
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality
2015-11-30 13:54 [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality Jisheng Zhang
@ 2015-12-06 9:28 ` Sebastian Hesselbarth
0 siblings, 0 replies; 5+ messages in thread
From: Sebastian Hesselbarth @ 2015-12-06 9:28 UTC (permalink / raw)
To: linux-arm-kernel
On 30.11.2015 14:54, Jisheng Zhang wrote:
> The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
> have gpios for card detection, write-protect, vqmmc and vmmc.
>
> This patch adds pinmux for this sdcard interface, then adds regulators
> for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
>
> Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Applied to berlin/dt.
> ---
> since v1:
Please also increment the patch subject version next time.
Thanks!
Sebastian
> - move sd1_pmux to soc dtsi
> - remove cd-inverted and make cd-gpio GPIO_ACTIVE_LOW
>
> arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 37 ++++++++++++++++++++++++++++--
> arch/arm/boot/dts/berlin2q.dtsi | 5 ++++
> 2 files changed, 40 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> index cdcf89b..33b2875 100644
> --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> @@ -84,12 +84,45 @@
> gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
> enable-active-high;
> };
> +
> + reg_sdio1_vmmc: regulator at 3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "sdio1_vmmc";
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_sdio1_vqmmc: regulator at 4 {
> + compatible = "regulator-gpio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "sdio1_vqmmc";
> + regulator-type = "voltage";
> + enable-active-high;
> + gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
> + states = <3300000 0x1
> + 1800000 0x0>;
> + };
> + };
> +};
> +
> +&soc_pinctrl {
> + sd1gpio_pmux: sd1pwr-pmux {
> + groups = "G23", "G32";
> + function = "gpio";
> };
> };
>
> &sdhci1 {
> - broken-cd;
> - sdhci,wp-inverted;
> + vmmc-supply = <®_sdio1_vmmc>;
> + vqmmc-supply = <®_sdio1_vqmmc>;
> + cd-gpios = <&portc 30 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>;
> + pinctrl-names = "default";
> status = "okay";
> };
>
> diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
> index 8ea177f..73a9362 100644
> --- a/arch/arm/boot/dts/berlin2q.dtsi
> +++ b/arch/arm/boot/dts/berlin2q.dtsi
> @@ -417,6 +417,11 @@
> soc_pinctrl: pin-controller {
> compatible = "marvell,berlin2q-soc-pinctrl";
>
> + sd1_pmux: sd1-pmux {
> + groups = "G31";
> + function = "sd1";
> + };
> +
> twsi0_pmux: twsi0-pmux {
> groups = "G6";
> function = "twsi0";
>
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality
@ 2015-11-26 13:13 Jisheng Zhang
2015-11-28 11:20 ` Sebastian Hesselbarth
0 siblings, 1 reply; 5+ messages in thread
From: Jisheng Zhang @ 2015-11-26 13:13 UTC (permalink / raw)
To: linux-arm-kernel
The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
have gpios for card detection, write-protect, vqmmc and vmmc.
This patch adds pinmux for this sdcard interface, then adds regulators
for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
---
arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 43 ++++++++++++++++++++++++++++--
1 file changed, 41 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
index cdcf89b..1fdc1d7 100644
--- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
+++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
@@ -84,12 +84,51 @@
gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ reg_sdio1_vmmc: regulator at 3 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "sdio1_vmmc";
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_sdio1_vqmmc: regulator at 4 {
+ compatible = "regulator-gpio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "sdio1_vqmmc";
+ regulator-type = "voltage";
+ enable-active-high;
+ gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
+ states = <3300000 0x1
+ 1800000 0x0>;
+ };
+ };
+};
+
+&soc_pinctrl {
+ sd1gpio_pmux: sd1pwr-pmux {
+ groups = "G23", "G32";
+ function = "gpio";
+ };
+
+ sd1_pmux: sd1-pmux {
+ groups = "G31";
+ function = "sd1";
};
};
&sdhci1 {
- broken-cd;
- sdhci,wp-inverted;
+ vmmc-supply = <®_sdio1_vmmc>;
+ vqmmc-supply = <®_sdio1_vqmmc>;
+ cd-inverted;
+ cd-gpios = <&portc 30 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>;
+ pinctrl-names = "default";
status = "okay";
};
--
2.6.2
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality
2015-11-26 13:13 Jisheng Zhang
@ 2015-11-28 11:20 ` Sebastian Hesselbarth
2015-11-30 13:07 ` Jisheng Zhang
0 siblings, 1 reply; 5+ messages in thread
From: Sebastian Hesselbarth @ 2015-11-28 11:20 UTC (permalink / raw)
To: linux-arm-kernel
On 26.11.2015 14:13, Jisheng Zhang wrote:
> The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
> have gpios for card detection, write-protect, vqmmc and vmmc.
>
> This patch adds pinmux for this sdcard interface, then adds regulators
> for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
>
> Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> ---
> arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 43 ++++++++++++++++++++++++++++--
> 1 file changed, 41 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> index cdcf89b..1fdc1d7 100644
> --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> @@ -84,12 +84,51 @@
> gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
> enable-active-high;
> };
> +
> + reg_sdio1_vmmc: regulator at 3 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "sdio1_vmmc";
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
> + };
> +
> + reg_sdio1_vqmmc: regulator at 4 {
> + compatible = "regulator-gpio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "sdio1_vqmmc";
> + regulator-type = "voltage";
> + enable-active-high;
> + gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
> + states = <3300000 0x1
> + 1800000 0x0>;
> + };
> + };
> +};
> +
> +&soc_pinctrl {
> + sd1gpio_pmux: sd1pwr-pmux {
> + groups = "G23", "G32";
> + function = "gpio";
> + };
> +
> + sd1_pmux: sd1-pmux {
> + groups = "G31";
> + function = "sd1";
Jisheng,
while having the sd1gpio_pmux in the board file, I think the
sd1_pmux is best kept in the SoC.dtsi.
> };
> };
>
> &sdhci1 {
> - broken-cd;
> - sdhci,wp-inverted;
> + vmmc-supply = <®_sdio1_vmmc>;
> + vqmmc-supply = <®_sdio1_vqmmc>;
> + cd-inverted;
> + cd-gpios = <&portc 30 GPIO_ACTIVE_HIGH>;
How about removing cd-inverted and make cd-gpio GPIO_ACTIVE_LOW
instead?
Sebastian
> + wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>;
> + pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>;
> + pinctrl-names = "default";
> status = "okay";
> };
>
>
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality
2015-11-28 11:20 ` Sebastian Hesselbarth
@ 2015-11-30 13:07 ` Jisheng Zhang
0 siblings, 0 replies; 5+ messages in thread
From: Jisheng Zhang @ 2015-11-30 13:07 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 28 Nov 2015 12:20:01 +0100
Sebastian Hesselbarth wrote:
> On 26.11.2015 14:13, Jisheng Zhang wrote:
> > The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
> > have gpios for card detection, write-protect, vqmmc and vmmc.
> >
> > This patch adds pinmux for this sdcard interface, then adds regulators
> > for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.
> >
> > Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
> > ---
> > arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 43 ++++++++++++++++++++++++++++--
> > 1 file changed, 41 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> > index cdcf89b..1fdc1d7 100644
> > --- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> > +++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
> > @@ -84,12 +84,51 @@
> > gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
> > enable-active-high;
> > };
> > +
> > + reg_sdio1_vmmc: regulator at 3 {
> > + compatible = "regulator-fixed";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "sdio1_vmmc";
> > + enable-active-high;
> > + regulator-boot-on;
> > + gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + reg_sdio1_vqmmc: regulator at 4 {
> > + compatible = "regulator-gpio";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "sdio1_vqmmc";
> > + regulator-type = "voltage";
> > + enable-active-high;
> > + gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
> > + states = <3300000 0x1
> > + 1800000 0x0>;
> > + };
> > + };
> > +};
> > +
> > +&soc_pinctrl {
> > + sd1gpio_pmux: sd1pwr-pmux {
> > + groups = "G23", "G32";
> > + function = "gpio";
> > + };
> > +
> > + sd1_pmux: sd1-pmux {
> > + groups = "G31";
> > + function = "sd1";
>
> Jisheng,
>
> while having the sd1gpio_pmux in the board file, I think the
> sd1_pmux is best kept in the SoC.dtsi.
Indeed, there's no other usage with sd1's pinmux. will do in v2
>
> > };
> > };
> >
> > &sdhci1 {
> > - broken-cd;
> > - sdhci,wp-inverted;
> > + vmmc-supply = <®_sdio1_vmmc>;
> > + vqmmc-supply = <®_sdio1_vqmmc>;
> > + cd-inverted;
> > + cd-gpios = <&portc 30 GPIO_ACTIVE_HIGH>;
>
> How about removing cd-inverted and make cd-gpio GPIO_ACTIVE_LOW
> instead?
Good idea! Will do in v2.
Thanks for your review,
Jisheng
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2015-12-06 9:28 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-11-30 13:54 [PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality Jisheng Zhang
2015-12-06 9:28 ` Sebastian Hesselbarth
-- strict thread matches above, loose matches on Subject: below --
2015-11-26 13:13 Jisheng Zhang
2015-11-28 11:20 ` Sebastian Hesselbarth
2015-11-30 13:07 ` Jisheng Zhang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).