[PATCH 2/6] ARM: DTS: da850: Use the new DT bindings for the eDMA3

[nsekhar@ti.com (Sekhar Nori)]

On Tuesday 15 December 2015 05:14 PM, Peter Ujfalusi wrote:
> On 12/15/2015 11:38 AM, Sekhar Nori wrote:
>> Hi Peter,
>>
>> On Friday 04 December 2015 07:23 PM, Peter Ujfalusi wrote:
>>> Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3.
>>> With the new bindings boards can customize and tweak the DMA channel
>>> priority to match their needs. With the new binding the memcpy is safe
>>> to be used since with the old binding it was not possible for a driver
>>> to know which channel is allowed to be used as non HW triggered channel.
>>> Using the new binding will allow us to reserve PaRAM slots to be used by
>>> the DSP which was not possible before and prevented the da850 boards to be
>>> moved to DT only.
>>>
>>> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
>>> ---
>>>  arch/arm/boot/dts/da850-enbw-cmc.dts |  5 +++++
>>>  arch/arm/boot/dts/da850-evm.dts      |  5 +++++
>>>  arch/arm/boot/dts/da850.dtsi         | 27 ++++++++++++++++++++++-----
>>>  3 files changed, 32 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/da850-enbw-cmc.dts b/arch/arm/boot/dts/da850-enbw-cmc.dts
>>> index e750ab9086d5..ca9117624cf9 100644
>>> --- a/arch/arm/boot/dts/da850-enbw-cmc.dts
>>> +++ b/arch/arm/boot/dts/da850-enbw-cmc.dts
>>> @@ -28,3 +28,8 @@
>>>  		};
>>>  	};
>>>  };
>>> +
>>> +&edma0 {
>>> +	ti,edma-reserved-slot-ranges = /bits/ 16 <32 50>;
>>> +	ti,edma-memcpy-channels = /bits/ 16 <20 21>;
>>> +};
>>> diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
>>> index d807285a61cd..33467feb272a 100644
>>> --- a/arch/arm/boot/dts/da850-evm.dts
>>> +++ b/arch/arm/boot/dts/da850-evm.dts
>>> @@ -243,3 +243,8 @@
>>>  	tx-num-evt = <32>;
>>>  	rx-num-evt = <32>;
>>>  };
>>> +
>>> +&edma0 {
>>> +	ti,edma-reserved-slot-ranges = /bits/ 16 <32 50>;
>>> +	ti,edma-memcpy-channels = /bits/ 16 <20 21>;
>>
>> These correspond to PRU events. It is true that most likely they will
>> never be used for peripheral DMA and can be dedicated as memcpy
>> channels. However, since this is being encoded in DT, we need to be sure
>> that they will never be used for peripheral DMA on this board.
>>
>> So, I would prefer if you do not reserve any channels for memcpy until
>> there is a real need/usecase for them. I know the board file has these
>> reserved but board file could be updated as you liked. With DT we need
>> to maintain backward compatibility. So I would rather do it when there
>> is an actual need for it.
> 
> If we do not reserve channels for memcpy then you will have no support for
> memcpy on these boards. Not sure if we use memcpy in any of our drivers in
> daVinci, so it might be just fine to not have DMA memcpy support at all.

Not that I know of. No driver uses DMA memcpy

> But how about using edma1's reserved channels as memcpy (19-23, 30-31)? I

I think this is much more reasonable.

> don't know which channels the DSP would use on these boards, so it is never
> going to be safe from that point.

Yeah, and thats why I think its better to add it as and when there is a
real need for it. At least at that point we are sure of the usecase.

> 
>> In future, if/when we gain QDMA support, the QDMA channels could be used
>> for memcopy.
> 
> Well, in short there is no way to get the qDMA working in a different way
> either. qDMA channel is in essence using 'normal' eDMA channel. This means
> that we still need to reserve the eDMA channel to be used for memcpy, but
> instead of SW triggering it (as we do it right now), we would need to use the
> channel as qDMA and set things up accordingly. I don't really see the benefit
> for qDMA mode to be honest.

I guess the only advantage is that they will not clash with peripheral
mode usage. But even then, some sort of reservation is needed. So I
guess QDMA is no better than the EDMA reserved channels?

>>
>>> +};
>>> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
>>> index e73f5efb3aa3..9e46eb51a8da 100644
>>> --- a/arch/arm/boot/dts/da850.dtsi
>>> +++ b/arch/arm/boot/dts/da850.dtsi
>>> @@ -151,11 +151,28 @@
>>>  
>>>  		};
>>>  		edma0: edma at 01c00000 {
>>> -			compatible = "ti,edma3";
>>> +			compatible = "ti,edma3-tpcc";
>>>  			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
>>>  			reg =	<0x0 0x8000>;
>>> -			interrupts = <11 13 12>;
>>> -			#dma-cells = <1>;
>>> +			reg-names = "edma3_cc";
>>> +			interrupts = <11 12>;
>>> +			interrupt-names = "edma3_ccint", "edma3_ccerrint";
>>> +			#dma-cells = <2>;
>>> +
>>> +			ti,tptcs = <&edma0_tptc0 7>, <&edma0_tptc1 0>;
>>> +			ti,edma-memcpy-channels = /bits/ 16 <20 21>;
>>
>> Same here. I would drop this.
> 
> OK, I'll drop this part.

For now, I think its better to not add any reservation. It can be added
when its really needed.

Thanks,
Sekhar