* [PATCH v2 0/2] Add DAC driver support for Vybrid SoC @ 2016-02-15 6:42 Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 1/2] ARM: dts: vfxxx: Add DAC node " Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver " Sanchayan Maity 0 siblings, 2 replies; 5+ messages in thread From: Sanchayan Maity @ 2016-02-15 6:42 UTC (permalink / raw) To: linux-arm-kernel Hello, This patchset adds support for the DAC peripheral on Vybrid SoC. Patchset is based on top of shawn's for-next branch and has been tested on a Toradex Colibri VF50 module. @Jonathan I kept the IIO_SHARED_BY_DIR instead of using IIO_SHARED_BY_ALL since this gives "out_conversion_mode" allowing me to distinguish this in the ABI documentation, that this is explicitly for the DAC. Since 4.5-rc4 was released recently and assuming this makes it with this or next version, I assumed the target kernel version would be 4.6 and used that in ABI documentation. Feedbacks and comments most welcome. Changes since v1: 1. Fix return type of vf610_dac_init function 2. Document conversion modes in sysfs-bus-iio-vf610 3. Remove "indexed" specification from iio_chan_spec 4. Use "return" directly from default case in switch 5. Remove DRIVER_NAME 6. Call vf610_dac_init before iio device registration 7. Define and use vf610_dac_exit function in remove and suspend 8. Add sysfs ABI documentation v1 of the patchset: http://www.spinics.net/lists/arm-kernel/msg481190.html Thanks & Regards, Sanchayan Maity. Sanchayan Maity (2): ARM: dts: vfxxx: Add DAC node for Vybrid SoC iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC Documentation/ABI/testing/sysfs-bus-iio-vf610 | 9 + .../devicetree/bindings/iio/dac/vf610-dac.txt | 20 ++ arch/arm/boot/dts/vfxxx.dtsi | 18 ++ drivers/iio/dac/Kconfig | 8 + drivers/iio/dac/Makefile | 1 + drivers/iio/dac/vf610_dac.c | 298 +++++++++++++++++++++ 6 files changed, 354 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/dac/vf610-dac.txt create mode 100644 drivers/iio/dac/vf610_dac.c -- 2.7.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 1/2] ARM: dts: vfxxx: Add DAC node for Vybrid SoC 2016-02-15 6:42 [PATCH v2 0/2] Add DAC driver support for Vybrid SoC Sanchayan Maity @ 2016-02-15 6:42 ` Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver " Sanchayan Maity 1 sibling, 0 replies; 5+ messages in thread From: Sanchayan Maity @ 2016-02-15 6:42 UTC (permalink / raw) To: linux-arm-kernel Add a device tree node entry for DAC peripheral on Vybrid SoC. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> --- arch/arm/boot/dts/vfxxx.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi index a5f07e3..8238069 100644 --- a/arch/arm/boot/dts/vfxxx.dtsi +++ b/arch/arm/boot/dts/vfxxx.dtsi @@ -602,6 +602,24 @@ status = "disabled"; }; + dac0: dac at 400cc000 { + compatible = "fsl,vf610-dac"; + reg = <0x400cc000 1000>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dac"; + clocks = <&clks VF610_CLK_DAC0>; + status = "disabled"; + }; + + dac1: dac at 400cd000 { + compatible = "fsl,vf610-dac"; + reg = <0x400cd000 1000>; + interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dac"; + clocks = <&clks VF610_CLK_DAC1>; + status = "disabled"; + }; + fec0: ethernet at 400d0000 { compatible = "fsl,mvf600-fec"; reg = <0x400d0000 0x1000>; -- 2.7.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC 2016-02-15 6:42 [PATCH v2 0/2] Add DAC driver support for Vybrid SoC Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 1/2] ARM: dts: vfxxx: Add DAC node " Sanchayan Maity @ 2016-02-15 6:42 ` Sanchayan Maity 2016-02-21 16:48 ` Jonathan Cameron 1 sibling, 1 reply; 5+ messages in thread From: Sanchayan Maity @ 2016-02-15 6:42 UTC (permalink / raw) To: linux-arm-kernel Add driver support for DAC peripheral on Vybrid SoC. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Rob Herring <robh@kernel.org> --- Documentation/ABI/testing/sysfs-bus-iio-vf610 | 9 + .../devicetree/bindings/iio/dac/vf610-dac.txt | 20 ++ drivers/iio/dac/Kconfig | 8 + drivers/iio/dac/Makefile | 1 + drivers/iio/dac/vf610_dac.c | 298 +++++++++++++++++++++ 5 files changed, 336 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/dac/vf610-dac.txt create mode 100644 drivers/iio/dac/vf610_dac.c diff --git a/Documentation/ABI/testing/sysfs-bus-iio-vf610 b/Documentation/ABI/testing/sysfs-bus-iio-vf610 index ecbc1f4..5ea809c 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-vf610 +++ b/Documentation/ABI/testing/sysfs-bus-iio-vf610 @@ -5,3 +5,12 @@ Description: Specifies the hardware conversion mode used. The three available modes are "normal", "high-speed" and "low-power", where the last is the default mode. + + +What: /sys/bus/iio/devices/iio:deviceX/out_conversion_mode +KernelVersion: 4.6 +Contact: linux-iio at vger.kernel.org +Description: + Specifies the hardware conversion mode used within DAC. + The two available modes are "high-power" and "low-power", + where "low-power" mode is the default mode. \ No newline at end of file diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt new file mode 100644 index 0000000..20c6c7a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt @@ -0,0 +1,20 @@ +Freescale vf610 Digital to Analog Converter bindings + +The devicetree bindings are for the new DAC driver written for +vf610 SoCs from Freescale. + +Required properties: +- compatible: Should contain "fsl,vf610-dac" +- reg: Offset and length of the register set for the device +- interrupts: Should contain the interrupt for the device +- clocks: The clock is needed by the DAC controller +- clock-names: Must contain "dac" matching entry in the clocks property. + +Example: +dac0: dac at 400cc000 { + compatible = "fsl,vf610-dac"; + reg = <0x400cc000 0x1000>; + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "dac"; + clocks = <&clks VF610_CLK_DAC0>; +}; diff --git a/drivers/iio/dac/Kconfig b/drivers/iio/dac/Kconfig index e701e28..8eb0502 100644 --- a/drivers/iio/dac/Kconfig +++ b/drivers/iio/dac/Kconfig @@ -196,4 +196,12 @@ config MCP4922 To compile this driver as a module, choose M here: the module will be called mcp4922. +config VF610_DAC + tristate "Vybrid vf610 DAC driver" + help + Say yes here to support Vybrid board digital-to-analog converter. + + This driver can also be built as a module. If so, the module will + be called vf610_dac. + endmenu diff --git a/drivers/iio/dac/Makefile b/drivers/iio/dac/Makefile index 63ae056..93feb27 100644 --- a/drivers/iio/dac/Makefile +++ b/drivers/iio/dac/Makefile @@ -21,3 +21,4 @@ obj-$(CONFIG_MAX517) += max517.o obj-$(CONFIG_MAX5821) += max5821.o obj-$(CONFIG_MCP4725) += mcp4725.o obj-$(CONFIG_MCP4922) += mcp4922.o +obj-$(CONFIG_VF610_DAC) += vf610_dac.o diff --git a/drivers/iio/dac/vf610_dac.c b/drivers/iio/dac/vf610_dac.c new file mode 100644 index 0000000..3f70f96 --- /dev/null +++ b/drivers/iio/dac/vf610_dac.c @@ -0,0 +1,298 @@ +/* + * Freescale Vybrid vf610 DAC driver + * + * Copyright 2016 Toradex AG + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> + +#define VF610_DACx_STATCTRL 0x20 + +#define VF610_DAC_DACEN BIT(15) +#define VF610_DAC_DACRFS BIT(14) +#define VF610_DAC_LPEN BIT(11) + +#define VF610_DAC_DAT0(x) ((x) & 0xFFF) + +enum vf610_conversion_mode_sel { + VF610_DAC_CONV_HIGH_POWER, + VF610_DAC_CONV_LOW_POWER, +}; + +struct vf610_dac { + struct clk *clk; + struct device *dev; + enum vf610_conversion_mode_sel conv_mode; + void __iomem *regs; +}; + +static void vf610_dac_init(struct vf610_dac *info) +{ + int val; + + info->conv_mode = VF610_DAC_CONV_LOW_POWER; + val = VF610_DAC_DACEN | VF610_DAC_DACRFS | + VF610_DAC_LPEN; + writel(val, info->regs + VF610_DACx_STATCTRL); +} + +static void vf610_dac_exit(struct vf610_dac *info) +{ + int val; + + val = readl(info->regs + VF610_DACx_STATCTRL); + val &= ~VF610_DAC_DACEN; + writel(val, info->regs + VF610_DACx_STATCTRL); +} + +static int vf610_set_conversion_mode(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + unsigned int mode) +{ + struct vf610_dac *info = iio_priv(indio_dev); + int val; + + mutex_lock(&indio_dev->mlock); + info->conv_mode = mode; + val = readl(info->regs + VF610_DACx_STATCTRL); + if (mode) + val |= VF610_DAC_LPEN; + else + val &= ~VF610_DAC_LPEN; + writel(val, info->regs + VF610_DACx_STATCTRL); + mutex_unlock(&indio_dev->mlock); + + return 0; +} + +static int vf610_get_conversion_mode(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan) +{ + struct vf610_dac *info = iio_priv(indio_dev); + + return info->conv_mode; +} + +static const char * const vf610_conv_modes[] = { "high-power", "low-power" }; + +static const struct iio_enum vf610_conversion_mode = { + .items = vf610_conv_modes, + .num_items = ARRAY_SIZE(vf610_conv_modes), + .get = vf610_get_conversion_mode, + .set = vf610_set_conversion_mode, +}; + +static const struct iio_chan_spec_ext_info vf610_ext_info[] = { + IIO_ENUM("conversion_mode", IIO_SHARED_BY_DIR, + &vf610_conversion_mode), + {}, +}; + +#define VF610_DAC_CHAN(_chan_type) { \ + .type = (_chan_type), \ + .output = 1, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .ext_info = vf610_ext_info, \ +} + +static const struct iio_chan_spec vf610_dac_iio_channels[] = { + VF610_DAC_CHAN(IIO_VOLTAGE), +}; + +static int vf610_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, + long mask) +{ + struct vf610_dac *info = iio_priv(indio_dev); + + switch (mask) { + case IIO_CHAN_INFO_RAW: + *val = VF610_DAC_DAT0(readl(info->regs)); + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + /* + * DACRFS is always 1 for valid reference and typical + * reference voltage as per Vybrid datasheet is 3.3V + * from section 9.1.2.1 of Vybrid datasheet + */ + *val = 3300 /* mV */; + *val2 = 12; + return IIO_VAL_FRACTIONAL_LOG2; + + default: + return -EINVAL; + } +} + +static int vf610_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, + long mask) +{ + struct vf610_dac *info = iio_priv(indio_dev); + + switch (mask) { + case IIO_CHAN_INFO_RAW: + mutex_lock(&indio_dev->mlock); + writel(VF610_DAC_DAT0(val), info->regs); + mutex_unlock(&indio_dev->mlock); + return 0; + + default: + return -EINVAL; + } +} + +static const struct iio_info vf610_dac_iio_info = { + .driver_module = THIS_MODULE, + .read_raw = &vf610_read_raw, + .write_raw = &vf610_write_raw, +}; + +static const struct of_device_id vf610_dac_match[] = { + { .compatible = "fsl,vf610-dac", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, vf610_dac_match); + +static int vf610_dac_probe(struct platform_device *pdev) +{ + struct iio_dev *indio_dev; + struct vf610_dac *info; + struct resource *mem; + int ret; + + indio_dev = devm_iio_device_alloc(&pdev->dev, + sizeof(struct vf610_dac)); + if (!indio_dev) { + dev_err(&pdev->dev, "Failed allocating iio device\n"); + return -ENOMEM; + } + + info = iio_priv(indio_dev); + info->dev = &pdev->dev; + + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + info->regs = devm_ioremap_resource(&pdev->dev, mem); + if (IS_ERR(info->regs)) + return PTR_ERR(info->regs); + + info->clk = devm_clk_get(&pdev->dev, "dac"); + if (IS_ERR(info->clk)) { + dev_err(&pdev->dev, "Failed getting clock, err = %ld\n", + PTR_ERR(info->clk)); + return PTR_ERR(info->clk); + } + + platform_set_drvdata(pdev, indio_dev); + + indio_dev->name = dev_name(&pdev->dev); + indio_dev->dev.parent = &pdev->dev; + indio_dev->dev.of_node = pdev->dev.of_node; + indio_dev->info = &vf610_dac_iio_info; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = vf610_dac_iio_channels; + indio_dev->num_channels = ARRAY_SIZE(vf610_dac_iio_channels); + + ret = clk_prepare_enable(info->clk); + if (ret) { + dev_err(&pdev->dev, + "Could not prepare or enable the clock\n"); + return ret; + } + + vf610_dac_init(info); + + ret = iio_device_register(indio_dev); + if (ret) { + dev_err(&pdev->dev, "Couldn't register the device\n"); + goto error_iio_device_register; + } + + return 0; + +error_iio_device_register: + clk_disable_unprepare(info->clk); + + return ret; +} + +static int vf610_dac_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + struct vf610_dac *info = iio_priv(indio_dev); + + vf610_dac_exit(info); + iio_device_unregister(indio_dev); + clk_disable_unprepare(info->clk); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int vf610_dac_suspend(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct vf610_dac *info = iio_priv(indio_dev); + + vf610_dac_exit(info); + clk_disable_unprepare(info->clk); + + return 0; +} + +static int vf610_dac_resume(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct vf610_dac *info = iio_priv(indio_dev); + int ret; + + ret = clk_prepare_enable(info->clk); + if (ret) + return ret; + + vf610_dac_init(info); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(vf610_dac_pm_ops, vf610_dac_suspend, vf610_dac_resume); + +static struct platform_driver vf610_dac_driver = { + .probe = vf610_dac_probe, + .remove = vf610_dac_remove, + .driver = { + .name = "vf610-dac", + .of_match_table = vf610_dac_match, + .pm = &vf610_dac_pm_ops, + }, +}; +module_platform_driver(vf610_dac_driver); + +MODULE_AUTHOR("Sanchayan Maity <sanchayan.maity@toradex.com"); +MODULE_DESCRIPTION("Freescale VF610 DAC driver"); +MODULE_LICENSE("GPL v2"); -- 2.7.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC 2016-02-15 6:42 ` [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver " Sanchayan Maity @ 2016-02-21 16:48 ` Jonathan Cameron 2016-02-21 19:37 ` Jonathan Cameron 0 siblings, 1 reply; 5+ messages in thread From: Jonathan Cameron @ 2016-02-21 16:48 UTC (permalink / raw) To: linux-arm-kernel On 15 February 2016 06:42:33 GMT+00:00, Sanchayan Maity <maitysanchayan@gmail.com> wrote: >Add driver support for DAC peripheral on Vybrid SoC. > >Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> >Acked-by: Rob Herring <robh@kernel.org> Ordering is wrong in remove. I may well fix this up and apply later today. Otherwise looks good to me. >--- > Documentation/ABI/testing/sysfs-bus-iio-vf610 | 9 + > .../devicetree/bindings/iio/dac/vf610-dac.txt | 20 ++ > drivers/iio/dac/Kconfig | 8 + > drivers/iio/dac/Makefile | 1 + >drivers/iio/dac/vf610_dac.c | 298 >+++++++++++++++++++++ > 5 files changed, 336 insertions(+) >create mode 100644 >Documentation/devicetree/bindings/iio/dac/vf610-dac.txt > create mode 100644 drivers/iio/dac/vf610_dac.c > >diff --git a/Documentation/ABI/testing/sysfs-bus-iio-vf610 >b/Documentation/ABI/testing/sysfs-bus-iio-vf610 >index ecbc1f4..5ea809c 100644 >--- a/Documentation/ABI/testing/sysfs-bus-iio-vf610 >+++ b/Documentation/ABI/testing/sysfs-bus-iio-vf610 >@@ -5,3 +5,12 @@ Description: > Specifies the hardware conversion mode used. The three > available modes are "normal", "high-speed" and "low-power", > where the last is the default mode. >+ >+ >+What: /sys/bus/iio/devices/iio:deviceX/out_conversion_mode >+KernelVersion: 4.6 >+Contact: linux-iio at vger.kernel.org >+Description: >+ Specifies the hardware conversion mode used within DAC. >+ The two available modes are "high-power" and "low-power", >+ where "low-power" mode is the default mode. >\ No newline at end of file >diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >new file mode 100644 >index 0000000..20c6c7a >--- /dev/null >+++ b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >@@ -0,0 +1,20 @@ >+Freescale vf610 Digital to Analog Converter bindings >+ >+The devicetree bindings are for the new DAC driver written for >+vf610 SoCs from Freescale. >+ >+Required properties: >+- compatible: Should contain "fsl,vf610-dac" >+- reg: Offset and length of the register set for the device >+- interrupts: Should contain the interrupt for the device >+- clocks: The clock is needed by the DAC controller >+- clock-names: Must contain "dac" matching entry in the clocks >property. >+ >+Example: >+dac0: dac at 400cc000 { >+ compatible = "fsl,vf610-dac"; >+ reg = <0x400cc000 0x1000>; >+ interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; >+ clock-names = "dac"; >+ clocks = <&clks VF610_CLK_DAC0>; >+}; >diff --git a/drivers/iio/dac/Kconfig b/drivers/iio/dac/Kconfig >index e701e28..8eb0502 100644 >--- a/drivers/iio/dac/Kconfig >+++ b/drivers/iio/dac/Kconfig >@@ -196,4 +196,12 @@ config MCP4922 > To compile this driver as a module, choose M here: the module > will be called mcp4922. > >+config VF610_DAC >+ tristate "Vybrid vf610 DAC driver" >+ help >+ Say yes here to support Vybrid board digital-to-analog converter. >+ >+ This driver can also be built as a module. If so, the module will >+ be called vf610_dac. >+ > endmenu >diff --git a/drivers/iio/dac/Makefile b/drivers/iio/dac/Makefile >index 63ae056..93feb27 100644 >--- a/drivers/iio/dac/Makefile >+++ b/drivers/iio/dac/Makefile >@@ -21,3 +21,4 @@ obj-$(CONFIG_MAX517) += max517.o > obj-$(CONFIG_MAX5821) += max5821.o > obj-$(CONFIG_MCP4725) += mcp4725.o > obj-$(CONFIG_MCP4922) += mcp4922.o >+obj-$(CONFIG_VF610_DAC) += vf610_dac.o >diff --git a/drivers/iio/dac/vf610_dac.c b/drivers/iio/dac/vf610_dac.c >new file mode 100644 >index 0000000..3f70f96 >--- /dev/null >+++ b/drivers/iio/dac/vf610_dac.c >@@ -0,0 +1,298 @@ >+/* >+ * Freescale Vybrid vf610 DAC driver >+ * >+ * Copyright 2016 Toradex AG >+ * >+ * This program is free software; you can redistribute it and/or >modify >+ * it under the terms of the GNU General Public License as published >by >+ * the Free Software Foundation; either version 2 of the License, or >+ * (at your option) any later version. >+ * >+ * This program is distributed in the hope that it will be useful, >+ * but WITHOUT ANY WARRANTY; without even the implied warranty of >+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >+ * GNU General Public License for more details. >+ */ >+ >+#include <linux/clk.h> >+#include <linux/err.h> >+#include <linux/interrupt.h> >+#include <linux/io.h> >+#include <linux/kernel.h> >+#include <linux/module.h> >+#include <linux/platform_device.h> >+#include <linux/regulator/consumer.h> >+#include <linux/slab.h> >+ >+#include <linux/iio/iio.h> >+#include <linux/iio/sysfs.h> >+ >+#define VF610_DACx_STATCTRL 0x20 >+ >+#define VF610_DAC_DACEN BIT(15) >+#define VF610_DAC_DACRFS BIT(14) >+#define VF610_DAC_LPEN BIT(11) >+ >+#define VF610_DAC_DAT0(x) ((x) & 0xFFF) >+ >+enum vf610_conversion_mode_sel { >+ VF610_DAC_CONV_HIGH_POWER, >+ VF610_DAC_CONV_LOW_POWER, >+}; >+ >+struct vf610_dac { >+ struct clk *clk; >+ struct device *dev; >+ enum vf610_conversion_mode_sel conv_mode; >+ void __iomem *regs; >+}; >+ >+static void vf610_dac_init(struct vf610_dac *info) >+{ >+ int val; >+ >+ info->conv_mode = VF610_DAC_CONV_LOW_POWER; >+ val = VF610_DAC_DACEN | VF610_DAC_DACRFS | >+ VF610_DAC_LPEN; >+ writel(val, info->regs + VF610_DACx_STATCTRL); >+} >+ >+static void vf610_dac_exit(struct vf610_dac *info) >+{ >+ int val; >+ >+ val = readl(info->regs + VF610_DACx_STATCTRL); >+ val &= ~VF610_DAC_DACEN; >+ writel(val, info->regs + VF610_DACx_STATCTRL); >+} >+ >+static int vf610_set_conversion_mode(struct iio_dev *indio_dev, >+ const struct iio_chan_spec *chan, >+ unsigned int mode) >+{ >+ struct vf610_dac *info = iio_priv(indio_dev); >+ int val; >+ >+ mutex_lock(&indio_dev->mlock); >+ info->conv_mode = mode; >+ val = readl(info->regs + VF610_DACx_STATCTRL); >+ if (mode) >+ val |= VF610_DAC_LPEN; >+ else >+ val &= ~VF610_DAC_LPEN; >+ writel(val, info->regs + VF610_DACx_STATCTRL); >+ mutex_unlock(&indio_dev->mlock); >+ >+ return 0; >+} >+ >+static int vf610_get_conversion_mode(struct iio_dev *indio_dev, >+ const struct iio_chan_spec *chan) >+{ >+ struct vf610_dac *info = iio_priv(indio_dev); >+ >+ return info->conv_mode; >+} >+ >+static const char * const vf610_conv_modes[] = { "high-power", >"low-power" }; >+ >+static const struct iio_enum vf610_conversion_mode = { >+ .items = vf610_conv_modes, >+ .num_items = ARRAY_SIZE(vf610_conv_modes), >+ .get = vf610_get_conversion_mode, >+ .set = vf610_set_conversion_mode, >+}; >+ >+static const struct iio_chan_spec_ext_info vf610_ext_info[] = { >+ IIO_ENUM("conversion_mode", IIO_SHARED_BY_DIR, >+ &vf610_conversion_mode), >+ {}, >+}; >+ >+#define VF610_DAC_CHAN(_chan_type) { \ >+ .type = (_chan_type), \ >+ .output = 1, \ >+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ >+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ >+ .ext_info = vf610_ext_info, \ >+} >+ >+static const struct iio_chan_spec vf610_dac_iio_channels[] = { >+ VF610_DAC_CHAN(IIO_VOLTAGE), >+}; >+ >+static int vf610_read_raw(struct iio_dev *indio_dev, >+ struct iio_chan_spec const *chan, >+ int *val, int *val2, >+ long mask) >+{ >+ struct vf610_dac *info = iio_priv(indio_dev); >+ >+ switch (mask) { >+ case IIO_CHAN_INFO_RAW: >+ *val = VF610_DAC_DAT0(readl(info->regs)); >+ return IIO_VAL_INT; >+ case IIO_CHAN_INFO_SCALE: >+ /* >+ * DACRFS is always 1 for valid reference and typical >+ * reference voltage as per Vybrid datasheet is 3.3V >+ * from section 9.1.2.1 of Vybrid datasheet >+ */ >+ *val = 3300 /* mV */; >+ *val2 = 12; >+ return IIO_VAL_FRACTIONAL_LOG2; >+ >+ default: >+ return -EINVAL; >+ } >+} >+ >+static int vf610_write_raw(struct iio_dev *indio_dev, >+ struct iio_chan_spec const *chan, >+ int val, int val2, >+ long mask) >+{ >+ struct vf610_dac *info = iio_priv(indio_dev); >+ >+ switch (mask) { >+ case IIO_CHAN_INFO_RAW: >+ mutex_lock(&indio_dev->mlock); >+ writel(VF610_DAC_DAT0(val), info->regs); >+ mutex_unlock(&indio_dev->mlock); >+ return 0; >+ >+ default: >+ return -EINVAL; >+ } >+} >+ >+static const struct iio_info vf610_dac_iio_info = { >+ .driver_module = THIS_MODULE, >+ .read_raw = &vf610_read_raw, >+ .write_raw = &vf610_write_raw, >+}; >+ >+static const struct of_device_id vf610_dac_match[] = { >+ { .compatible = "fsl,vf610-dac", }, >+ { /* sentinel */ } >+}; >+MODULE_DEVICE_TABLE(of, vf610_dac_match); >+ >+static int vf610_dac_probe(struct platform_device *pdev) >+{ >+ struct iio_dev *indio_dev; >+ struct vf610_dac *info; >+ struct resource *mem; >+ int ret; >+ >+ indio_dev = devm_iio_device_alloc(&pdev->dev, >+ sizeof(struct vf610_dac)); >+ if (!indio_dev) { >+ dev_err(&pdev->dev, "Failed allocating iio device\n"); >+ return -ENOMEM; >+ } >+ >+ info = iio_priv(indio_dev); >+ info->dev = &pdev->dev; >+ >+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); >+ info->regs = devm_ioremap_resource(&pdev->dev, mem); >+ if (IS_ERR(info->regs)) >+ return PTR_ERR(info->regs); >+ >+ info->clk = devm_clk_get(&pdev->dev, "dac"); >+ if (IS_ERR(info->clk)) { >+ dev_err(&pdev->dev, "Failed getting clock, err = %ld\n", >+ PTR_ERR(info->clk)); >+ return PTR_ERR(info->clk); >+ } >+ >+ platform_set_drvdata(pdev, indio_dev); >+ >+ indio_dev->name = dev_name(&pdev->dev); >+ indio_dev->dev.parent = &pdev->dev; >+ indio_dev->dev.of_node = pdev->dev.of_node; >+ indio_dev->info = &vf610_dac_iio_info; >+ indio_dev->modes = INDIO_DIRECT_MODE; >+ indio_dev->channels = vf610_dac_iio_channels; >+ indio_dev->num_channels = ARRAY_SIZE(vf610_dac_iio_channels); >+ >+ ret = clk_prepare_enable(info->clk); >+ if (ret) { >+ dev_err(&pdev->dev, >+ "Could not prepare or enable the clock\n"); >+ return ret; >+ } >+ >+ vf610_dac_init(info); >+ >+ ret = iio_device_register(indio_dev); >+ if (ret) { >+ dev_err(&pdev->dev, "Couldn't register the device\n"); >+ goto error_iio_device_register; >+ } >+ >+ return 0; >+ >+error_iio_device_register: >+ clk_disable_unprepare(info->clk); >+ >+ return ret; >+} >+ >+static int vf610_dac_remove(struct platform_device *pdev) >+{ >+ struct iio_dev *indio_dev = platform_get_drvdata(pdev); >+ struct vf610_dac *info = iio_priv(indio_dev); >+ >+ vf610_dac_exit(info); Should be reverse order of probe so exit after the unregister below. Right now you are disabling the hardware before removing the userspace interfaces. >+ iio_device_unregister(indio_dev); >+ clk_disable_unprepare(info->clk); >+ >+ return 0; >+} >+ >+#ifdef CONFIG_PM_SLEEP >+static int vf610_dac_suspend(struct device *dev) >+{ >+ struct iio_dev *indio_dev = dev_get_drvdata(dev); >+ struct vf610_dac *info = iio_priv(indio_dev); >+ >+ vf610_dac_exit(info); >+ clk_disable_unprepare(info->clk); >+ >+ return 0; >+} >+ >+static int vf610_dac_resume(struct device *dev) >+{ >+ struct iio_dev *indio_dev = dev_get_drvdata(dev); >+ struct vf610_dac *info = iio_priv(indio_dev); >+ int ret; >+ >+ ret = clk_prepare_enable(info->clk); >+ if (ret) >+ return ret; >+ >+ vf610_dac_init(info); >+ >+ return 0; >+} >+#endif >+ >+static SIMPLE_DEV_PM_OPS(vf610_dac_pm_ops, vf610_dac_suspend, >vf610_dac_resume); >+ >+static struct platform_driver vf610_dac_driver = { >+ .probe = vf610_dac_probe, >+ .remove = vf610_dac_remove, >+ .driver = { >+ .name = "vf610-dac", >+ .of_match_table = vf610_dac_match, >+ .pm = &vf610_dac_pm_ops, >+ }, >+}; >+module_platform_driver(vf610_dac_driver); >+ >+MODULE_AUTHOR("Sanchayan Maity <sanchayan.maity@toradex.com"); >+MODULE_DESCRIPTION("Freescale VF610 DAC driver"); >+MODULE_LICENSE("GPL v2"); -- Sent from my Android device with K-9 Mail. Please excuse my brevity. ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver for Vybrid SoC 2016-02-21 16:48 ` Jonathan Cameron @ 2016-02-21 19:37 ` Jonathan Cameron 0 siblings, 0 replies; 5+ messages in thread From: Jonathan Cameron @ 2016-02-21 19:37 UTC (permalink / raw) To: linux-arm-kernel On 21/02/16 16:48, Jonathan Cameron wrote: > > > On 15 February 2016 06:42:33 GMT+00:00, Sanchayan Maity <maitysanchayan@gmail.com> wrote: >> Add driver support for DAC peripheral on Vybrid SoC. >> >> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> >> Acked-by: Rob Herring <robh@kernel.org> > Ordering is wrong in remove. I may well fix this up and apply later today. I also note that the Kconfig dependencies are rather sparse. Presumably needs depends on HAS_IOMEM at the very least. Anyhow, changes are getting less trivial so I'm not going to apply this without another revision. Jonathan > Otherwise looks good to me. >> --- >> Documentation/ABI/testing/sysfs-bus-iio-vf610 | 9 + >> .../devicetree/bindings/iio/dac/vf610-dac.txt | 20 ++ >> drivers/iio/dac/Kconfig | 8 + >> drivers/iio/dac/Makefile | 1 + >> drivers/iio/dac/vf610_dac.c | 298 >> +++++++++++++++++++++ >> 5 files changed, 336 insertions(+) >> create mode 100644 >> Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >> create mode 100644 drivers/iio/dac/vf610_dac.c >> >> diff --git a/Documentation/ABI/testing/sysfs-bus-iio-vf610 >> b/Documentation/ABI/testing/sysfs-bus-iio-vf610 >> index ecbc1f4..5ea809c 100644 >> --- a/Documentation/ABI/testing/sysfs-bus-iio-vf610 >> +++ b/Documentation/ABI/testing/sysfs-bus-iio-vf610 >> @@ -5,3 +5,12 @@ Description: >> Specifies the hardware conversion mode used. The three >> available modes are "normal", "high-speed" and "low-power", >> where the last is the default mode. >> + >> + >> +What: /sys/bus/iio/devices/iio:deviceX/out_conversion_mode >> +KernelVersion: 4.6 >> +Contact: linux-iio at vger.kernel.org >> +Description: >> + Specifies the hardware conversion mode used within DAC. >> + The two available modes are "high-power" and "low-power", >> + where "low-power" mode is the default mode. >> \ No newline at end of file >> diff --git a/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >> b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >> new file mode 100644 >> index 0000000..20c6c7a >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/iio/dac/vf610-dac.txt >> @@ -0,0 +1,20 @@ >> +Freescale vf610 Digital to Analog Converter bindings >> + >> +The devicetree bindings are for the new DAC driver written for >> +vf610 SoCs from Freescale. >> + >> +Required properties: >> +- compatible: Should contain "fsl,vf610-dac" >> +- reg: Offset and length of the register set for the device >> +- interrupts: Should contain the interrupt for the device >> +- clocks: The clock is needed by the DAC controller >> +- clock-names: Must contain "dac" matching entry in the clocks >> property. >> + >> +Example: >> +dac0: dac at 400cc000 { >> + compatible = "fsl,vf610-dac"; >> + reg = <0x400cc000 0x1000>; >> + interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; >> + clock-names = "dac"; >> + clocks = <&clks VF610_CLK_DAC0>; >> +}; >> diff --git a/drivers/iio/dac/Kconfig b/drivers/iio/dac/Kconfig >> index e701e28..8eb0502 100644 >> --- a/drivers/iio/dac/Kconfig >> +++ b/drivers/iio/dac/Kconfig >> @@ -196,4 +196,12 @@ config MCP4922 >> To compile this driver as a module, choose M here: the module >> will be called mcp4922. >> >> +config VF610_DAC >> + tristate "Vybrid vf610 DAC driver" >> + help >> + Say yes here to support Vybrid board digital-to-analog converter. >> + >> + This driver can also be built as a module. If so, the module will >> + be called vf610_dac. >> + >> endmenu >> diff --git a/drivers/iio/dac/Makefile b/drivers/iio/dac/Makefile >> index 63ae056..93feb27 100644 >> --- a/drivers/iio/dac/Makefile >> +++ b/drivers/iio/dac/Makefile >> @@ -21,3 +21,4 @@ obj-$(CONFIG_MAX517) += max517.o >> obj-$(CONFIG_MAX5821) += max5821.o >> obj-$(CONFIG_MCP4725) += mcp4725.o >> obj-$(CONFIG_MCP4922) += mcp4922.o >> +obj-$(CONFIG_VF610_DAC) += vf610_dac.o >> diff --git a/drivers/iio/dac/vf610_dac.c b/drivers/iio/dac/vf610_dac.c >> new file mode 100644 >> index 0000000..3f70f96 >> --- /dev/null >> +++ b/drivers/iio/dac/vf610_dac.c >> @@ -0,0 +1,298 @@ >> +/* >> + * Freescale Vybrid vf610 DAC driver >> + * >> + * Copyright 2016 Toradex AG >> + * >> + * This program is free software; you can redistribute it and/or >> modify >> + * it under the terms of the GNU General Public License as published >> by >> + * the Free Software Foundation; either version 2 of the License, or >> + * (at your option) any later version. >> + * >> + * This program is distributed in the hope that it will be useful, >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >> + * GNU General Public License for more details. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/err.h> >> +#include <linux/interrupt.h> >> +#include <linux/io.h> >> +#include <linux/kernel.h> >> +#include <linux/module.h> >> +#include <linux/platform_device.h> >> +#include <linux/regulator/consumer.h> >> +#include <linux/slab.h> >> + >> +#include <linux/iio/iio.h> >> +#include <linux/iio/sysfs.h> >> + >> +#define VF610_DACx_STATCTRL 0x20 >> + >> +#define VF610_DAC_DACEN BIT(15) >> +#define VF610_DAC_DACRFS BIT(14) >> +#define VF610_DAC_LPEN BIT(11) >> + >> +#define VF610_DAC_DAT0(x) ((x) & 0xFFF) >> + >> +enum vf610_conversion_mode_sel { >> + VF610_DAC_CONV_HIGH_POWER, >> + VF610_DAC_CONV_LOW_POWER, >> +}; >> + >> +struct vf610_dac { >> + struct clk *clk; >> + struct device *dev; >> + enum vf610_conversion_mode_sel conv_mode; >> + void __iomem *regs; >> +}; >> + >> +static void vf610_dac_init(struct vf610_dac *info) >> +{ >> + int val; >> + >> + info->conv_mode = VF610_DAC_CONV_LOW_POWER; >> + val = VF610_DAC_DACEN | VF610_DAC_DACRFS | >> + VF610_DAC_LPEN; >> + writel(val, info->regs + VF610_DACx_STATCTRL); >> +} >> + >> +static void vf610_dac_exit(struct vf610_dac *info) >> +{ >> + int val; >> + >> + val = readl(info->regs + VF610_DACx_STATCTRL); >> + val &= ~VF610_DAC_DACEN; >> + writel(val, info->regs + VF610_DACx_STATCTRL); >> +} >> + >> +static int vf610_set_conversion_mode(struct iio_dev *indio_dev, >> + const struct iio_chan_spec *chan, >> + unsigned int mode) >> +{ >> + struct vf610_dac *info = iio_priv(indio_dev); >> + int val; >> + >> + mutex_lock(&indio_dev->mlock); >> + info->conv_mode = mode; >> + val = readl(info->regs + VF610_DACx_STATCTRL); >> + if (mode) >> + val |= VF610_DAC_LPEN; >> + else >> + val &= ~VF610_DAC_LPEN; >> + writel(val, info->regs + VF610_DACx_STATCTRL); >> + mutex_unlock(&indio_dev->mlock); >> + >> + return 0; >> +} >> + >> +static int vf610_get_conversion_mode(struct iio_dev *indio_dev, >> + const struct iio_chan_spec *chan) >> +{ >> + struct vf610_dac *info = iio_priv(indio_dev); >> + >> + return info->conv_mode; >> +} >> + >> +static const char * const vf610_conv_modes[] = { "high-power", >> "low-power" }; >> + >> +static const struct iio_enum vf610_conversion_mode = { >> + .items = vf610_conv_modes, >> + .num_items = ARRAY_SIZE(vf610_conv_modes), >> + .get = vf610_get_conversion_mode, >> + .set = vf610_set_conversion_mode, >> +}; >> + >> +static const struct iio_chan_spec_ext_info vf610_ext_info[] = { >> + IIO_ENUM("conversion_mode", IIO_SHARED_BY_DIR, >> + &vf610_conversion_mode), >> + {}, >> +}; >> + >> +#define VF610_DAC_CHAN(_chan_type) { \ >> + .type = (_chan_type), \ >> + .output = 1, \ >> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ >> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ >> + .ext_info = vf610_ext_info, \ >> +} >> + >> +static const struct iio_chan_spec vf610_dac_iio_channels[] = { >> + VF610_DAC_CHAN(IIO_VOLTAGE), >> +}; >> + >> +static int vf610_read_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int *val, int *val2, >> + long mask) >> +{ >> + struct vf610_dac *info = iio_priv(indio_dev); >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_RAW: >> + *val = VF610_DAC_DAT0(readl(info->regs)); >> + return IIO_VAL_INT; >> + case IIO_CHAN_INFO_SCALE: >> + /* >> + * DACRFS is always 1 for valid reference and typical >> + * reference voltage as per Vybrid datasheet is 3.3V >> + * from section 9.1.2.1 of Vybrid datasheet >> + */ >> + *val = 3300 /* mV */; >> + *val2 = 12; >> + return IIO_VAL_FRACTIONAL_LOG2; >> + >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static int vf610_write_raw(struct iio_dev *indio_dev, >> + struct iio_chan_spec const *chan, >> + int val, int val2, >> + long mask) >> +{ >> + struct vf610_dac *info = iio_priv(indio_dev); >> + >> + switch (mask) { >> + case IIO_CHAN_INFO_RAW: >> + mutex_lock(&indio_dev->mlock); >> + writel(VF610_DAC_DAT0(val), info->regs); >> + mutex_unlock(&indio_dev->mlock); >> + return 0; >> + >> + default: >> + return -EINVAL; >> + } >> +} >> + >> +static const struct iio_info vf610_dac_iio_info = { >> + .driver_module = THIS_MODULE, >> + .read_raw = &vf610_read_raw, >> + .write_raw = &vf610_write_raw, >> +}; >> + >> +static const struct of_device_id vf610_dac_match[] = { >> + { .compatible = "fsl,vf610-dac", }, >> + { /* sentinel */ } >> +}; >> +MODULE_DEVICE_TABLE(of, vf610_dac_match); >> + >> +static int vf610_dac_probe(struct platform_device *pdev) >> +{ >> + struct iio_dev *indio_dev; >> + struct vf610_dac *info; >> + struct resource *mem; >> + int ret; >> + >> + indio_dev = devm_iio_device_alloc(&pdev->dev, >> + sizeof(struct vf610_dac)); >> + if (!indio_dev) { >> + dev_err(&pdev->dev, "Failed allocating iio device\n"); >> + return -ENOMEM; >> + } >> + >> + info = iio_priv(indio_dev); >> + info->dev = &pdev->dev; >> + >> + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> + info->regs = devm_ioremap_resource(&pdev->dev, mem); >> + if (IS_ERR(info->regs)) >> + return PTR_ERR(info->regs); >> + >> + info->clk = devm_clk_get(&pdev->dev, "dac"); >> + if (IS_ERR(info->clk)) { >> + dev_err(&pdev->dev, "Failed getting clock, err = %ld\n", >> + PTR_ERR(info->clk)); >> + return PTR_ERR(info->clk); >> + } >> + >> + platform_set_drvdata(pdev, indio_dev); >> + >> + indio_dev->name = dev_name(&pdev->dev); >> + indio_dev->dev.parent = &pdev->dev; >> + indio_dev->dev.of_node = pdev->dev.of_node; >> + indio_dev->info = &vf610_dac_iio_info; >> + indio_dev->modes = INDIO_DIRECT_MODE; >> + indio_dev->channels = vf610_dac_iio_channels; >> + indio_dev->num_channels = ARRAY_SIZE(vf610_dac_iio_channels); >> + >> + ret = clk_prepare_enable(info->clk); >> + if (ret) { >> + dev_err(&pdev->dev, >> + "Could not prepare or enable the clock\n"); >> + return ret; >> + } >> + >> + vf610_dac_init(info); >> + >> + ret = iio_device_register(indio_dev); >> + if (ret) { >> + dev_err(&pdev->dev, "Couldn't register the device\n"); >> + goto error_iio_device_register; >> + } >> + >> + return 0; >> + >> +error_iio_device_register: >> + clk_disable_unprepare(info->clk); >> + >> + return ret; >> +} >> + >> +static int vf610_dac_remove(struct platform_device *pdev) >> +{ >> + struct iio_dev *indio_dev = platform_get_drvdata(pdev); >> + struct vf610_dac *info = iio_priv(indio_dev); >> + >> + vf610_dac_exit(info); > Should be reverse order of probe so exit after the unregister below. > Right now you are disabling the hardware before removing the userspace interfaces. >> + iio_device_unregister(indio_dev); >> + clk_disable_unprepare(info->clk); >> + >> + return 0; >> +} >> + >> +#ifdef CONFIG_PM_SLEEP >> +static int vf610_dac_suspend(struct device *dev) >> +{ >> + struct iio_dev *indio_dev = dev_get_drvdata(dev); >> + struct vf610_dac *info = iio_priv(indio_dev); >> + >> + vf610_dac_exit(info); >> + clk_disable_unprepare(info->clk); >> + >> + return 0; >> +} >> + >> +static int vf610_dac_resume(struct device *dev) >> +{ >> + struct iio_dev *indio_dev = dev_get_drvdata(dev); >> + struct vf610_dac *info = iio_priv(indio_dev); >> + int ret; >> + >> + ret = clk_prepare_enable(info->clk); >> + if (ret) >> + return ret; >> + >> + vf610_dac_init(info); >> + >> + return 0; >> +} >> +#endif >> + >> +static SIMPLE_DEV_PM_OPS(vf610_dac_pm_ops, vf610_dac_suspend, >> vf610_dac_resume); >> + >> +static struct platform_driver vf610_dac_driver = { >> + .probe = vf610_dac_probe, >> + .remove = vf610_dac_remove, >> + .driver = { >> + .name = "vf610-dac", >> + .of_match_table = vf610_dac_match, >> + .pm = &vf610_dac_pm_ops, >> + }, >> +}; >> +module_platform_driver(vf610_dac_driver); >> + >> +MODULE_AUTHOR("Sanchayan Maity <sanchayan.maity@toradex.com"); >> +MODULE_DESCRIPTION("Freescale VF610 DAC driver"); >> +MODULE_LICENSE("GPL v2"); > ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-02-21 19:37 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2016-02-15 6:42 [PATCH v2 0/2] Add DAC driver support for Vybrid SoC Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 1/2] ARM: dts: vfxxx: Add DAC node " Sanchayan Maity 2016-02-15 6:42 ` [PATCH v2 2/2] iio: dac: vf610_dac: Add IIO DAC driver " Sanchayan Maity 2016-02-21 16:48 ` Jonathan Cameron 2016-02-21 19:37 ` Jonathan Cameron
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).