[PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support

[PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support

[Andre Przywara]

Hi,

another update of the Allwinner A64 / Pine64 support series.
I added a solution for the PLL6 reuse issue (the same patch I posted
yesterday). Also I addressed the comments I got from Rob and Chen-Yu.
For a changelog see below.

This series provides initial support for the Allwinner A64 SoC,
which is based on four ARM Cortex-A53 cores implementing the ARMv8
64-bit architecture.
On top of this there is also initial support for the Pine64 board,
for which you can find more information and links in the linux-sunxi
Wiki [1].
The resulting kernel boots fine on my development samples I have
here, though the actual boot process is a bit involved at the moment.
You can find more information and a ready-to-flash image here [2].

Patch 1/10 removes the hardcoded "pll6" name for the PLL6 clock, so
it can be reused for the A64's PLL7, patch 2/10 uses that facility
for the Allwinner H3 SoC's PLL8.
Patch 3/10 enables the Allwinner/sunxi platform for the arm64
architecture, so one can select the required drivers during
configuration.
Patch 4/10 adds the pinctrl driver, which has been on the list before.
Patch 5 and 6 add a new generic driver for the bus clock gates which
relies on DT for providing the parent relationship. That makes adding
new SoCs much easier, since there should be no more kernel code
changes necessary.
Patch 7-9 add the new vendor name and the device tree files, the former
for the SoC itself, the latter for the Pine64 boards.
The final patch 10 updates defconfig, so that the generic arm64 kernel
supports the basic SoC drivers out of the box.

In the moment we support the basic peripherals like GIC, timer, clocks,
GPIOs, UARTs and (since v2) I2C.
The MMC IP block has changed a bit compared to previous SoCs, so the
existing driver is not 100% compatible. However the default delays seem
to work fine for the SD cards, so I included all the necessary bits in
here, since working MMC makes this series indefinitely more usable.
We can fix both the MMC driver and the DT in a compatible way later.

Please have a look and comment on the patches. We might want to split
the series if some patches seem too controversial for being merged
soonish, please let me know if this is the case and I am happy to
rearrange the series.

The patches are based on mripard/sunxi/for-next (since linux-next is
a bit messy atm). A working repo can be found over here[3].

Cheers,
Andre

Changelog v1 .. v2:
- Change the naming of DT nodes, identifiers and file names to include
  the wonderful Allwinner architecture prefix everywhere. You asked
  for it, you got it, enjoy!
- Drop SUNXI_MMC to be selected automatically, instead put it in the
  defconfig.
- Add a binding documentation for the new multi-bus-gates driver.
- Add a defconfig update patch.
- Lots of changes in the DTs, see the respective patches for details.

Changelog v2 .. v3:
- Reordered sunxi section in ARM64 platform config.
- Add PLL6 reuse patch and rework the .dtsi to use the existing binding.
- Drop unneeded module boilerplate for the pinctrl driver.
- Rename "owa" pin to "spdif".
- Rename pll8 to pll7 in the DT.
- Remove leading 0 in DT node address parts.
- Added Acks from Rob.

[1] http://linux-sunxi.org/Pine64
[2] https://github.com/apritzel/pine64
[3] https://github.com/apritzel/linux/commits/a64-v3

Andre Przywara (10):
  clk: sunxi: allow PLL6 clock to be reused
  ARM: dts: sunxi: make PLL8 in the H3 a proper clock
  arm64: Introduce Allwinner SoC config option
  drivers: pinctrl: add driver for Allwinner A64 SoC
  DT: clk: sunxi: add binding doc for the multi-bus-gates clock
  clk: sunxi: add generic multi-parent bus clock gates driver
  arm64: dts: add Allwinner A64 SoC .dtsi
  of: add vendor prefix for Pine64
  arm64: dts: add Pine64 support
  arm64: add defconfig options for Allwinner SoCs

 Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
 Documentation/devicetree/bindings/clock/sunxi.txt  |   7 +
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 .../devicetree/bindings/vendor-prefixes.txt        |   1 +
 arch/arm/boot/dts/sun8i-h3.dtsi                    |  18 +-
 arch/arm64/Kconfig.platforms                       |   6 +
 arch/arm64/boot/dts/Makefile                       |   1 +
 arch/arm64/boot/dts/allwinner/Makefile             |   5 +
 .../dts/allwinner/sun50i-a64-pine64-common.dtsi    |  80 +++
 .../boot/dts/allwinner/sun50i-a64-pine64-plus.dts  |  59 ++
 .../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts |  58 ++
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi      | 624 +++++++++++++++++++++
 arch/arm64/configs/defconfig                       |   7 +
 drivers/clk/sunxi/Makefile                         |   1 +
 drivers/clk/sunxi/clk-factors.c                    |   3 +-
 drivers/clk/sunxi/clk-factors.h                    |   1 +
 drivers/clk/sunxi/clk-multi-gates.c                | 105 ++++
 drivers/clk/sunxi/clk-sunxi.c                      |   4 +-
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c         | 602 ++++++++++++++++++++
 21 files changed, 1577 insertions(+), 12 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/Makefile
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
 create mode 100644 drivers/clk/sunxi/clk-multi-gates.c
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c

-- 
2.6.4

[PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support

[Andre Przywara]

Subject: [PATCH v3 01/10] clk: sunxi: allow PLL6 clock to be reused

Currently we hard-code the base name for the PLL6 clock for both the
sun4i and sun6i variants in the driver (pll6 and pll6x2, respectively).
This unfortunately denies reusing this clock for the H3 and A64 PLL8
clock, which is the same otherwise.
Remove the hard-coded name in the source code and replace it with an
appropriate index into the clock-output-names array in the DT.
This is compatible with all current device trees, since they all carry
the hard-coded base name in there.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 drivers/clk/sunxi/clk-factors.c | 3 ++-
 drivers/clk/sunxi/clk-factors.h | 1 +
 drivers/clk/sunxi/clk-sunxi.c   | 4 ++--
 3 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/sunxi/clk-factors.c b/drivers/clk/sunxi/clk-factors.c
index ddefe96..7daf01d 100644
--- a/drivers/clk/sunxi/clk-factors.c
+++ b/drivers/clk/sunxi/clk-factors.c
@@ -202,7 +202,8 @@ struct clk *sunxi_factors_register(struct device_node *node,
 	if (data->name)
 		clk_name = data->name;
 	else
-		of_property_read_string(node, "clock-output-names", &clk_name);
+		of_property_read_string_index(node, "clock-output-names",
+					      data->name_idx, &clk_name);
 
 	factors = kzalloc(sizeof(struct clk_factors), GFP_KERNEL);
 	if (!factors)
diff --git a/drivers/clk/sunxi/clk-factors.h b/drivers/clk/sunxi/clk-factors.h
index 1e63c5b..3a7da86 100644
--- a/drivers/clk/sunxi/clk-factors.h
+++ b/drivers/clk/sunxi/clk-factors.h
@@ -36,6 +36,7 @@ struct factors_data {
 	void (*getter)(struct factors_request *req);
 	void (*recalc)(struct factors_request *req);
 	const char *name;
+	int name_idx;
 };
 
 struct clk_factors {
diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
index 99f60ef..53f5927 100644
--- a/drivers/clk/sunxi/clk-sunxi.c
+++ b/drivers/clk/sunxi/clk-sunxi.c
@@ -530,14 +530,14 @@ static const struct factors_data sun4i_pll6_data __initconst = {
 	.enable = 31,
 	.table = &sun4i_pll5_config,
 	.getter = sun4i_get_pll5_factors,
-	.name = "pll6",
+	.name_idx = 2,
 };
 
 static const struct factors_data sun6i_a31_pll6_data __initconst = {
 	.enable = 31,
 	.table = &sun6i_a31_pll6_config,
 	.getter = sun6i_a31_get_pll6_factors,
-	.name = "pll6x2",
+	.name_idx = 1,
 };
 
 static const struct factors_data sun5i_a13_ahb_data __initconst = {
-- 
2.6.4

[PATCH v3 02/10] ARM: dts: sunxi: make PLL8 in the H3 a proper clock

[Andre Przywara]

Now that we can reuse the A31 PLL6 clock driver for clocks other then
PLL6 itself, describe the PLL8 clock properly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm/boot/dts/sun8i-h3.dtsi | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index 3ba65c2..d84ea9b 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -137,12 +137,12 @@
 			clock-output-names = "pll6d2";
 		};
 
-		/* dummy clock until pll6 can be reused */
-		pll8: pll8_clk {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <1>;
-			clock-output-names = "pll8";
+		pll8: clk at c01c20044 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun6i-a31-pll6-clk";
+			reg = <0x01c20044 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll8", "pll8x2";
 		};
 
 		cpu: cpu_clk at 01c20050 {
@@ -243,7 +243,7 @@
 			#clock-cells = <1>;
 			compatible = "allwinner,sun4i-a10-mmc-clk";
 			reg = <0x01c20088 0x4>;
-			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
 			clock-output-names = "mmc0",
 					     "mmc0_output",
 					     "mmc0_sample";
@@ -253,7 +253,7 @@
 			#clock-cells = <1>;
 			compatible = "allwinner,sun4i-a10-mmc-clk";
 			reg = <0x01c2008c 0x4>;
-			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
 			clock-output-names = "mmc1",
 					     "mmc1_output",
 					     "mmc1_sample";
@@ -263,7 +263,7 @@
 			#clock-cells = <1>;
 			compatible = "allwinner,sun4i-a10-mmc-clk";
 			reg = <0x01c20090 0x4>;
-			clocks = <&osc24M>, <&pll6 0>, <&pll8>;
+			clocks = <&osc24M>, <&pll6 0>, <&pll8 0>;
 			clock-output-names = "mmc2",
 					     "mmc2_output",
 					     "mmc2_sample";
-- 
2.6.4

[PATCH v3 03/10] arm64: Introduce Allwinner SoC config option

[Andre Przywara]

To prepare for the Allwinner A64 SoC support, introduce a config
option to allow compiling Allwinner (aka. sunxi) specific drivers
for the arm64 architecture as well.
This patch just defines the ARCH_SUNXI symbol to allow Allwinner
specific drivers to be selected during kernel configuration.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/Kconfig.platforms | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 21074f6..97f5690 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -72,6 +72,11 @@ config ARCH_SEATTLE
 config ARCH_SHMOBILE
 	bool
 
+config ARCH_SUNXI
+	bool "Allwinner sunxi 64-bit SoC Family"
+	help
+	  This enables support for Allwinner sunxi based SoCs like the A64.
+
 config ARCH_RENESAS
 	bool "Renesas SoC Platforms"
 	select ARCH_SHMOBILE
-- 
2.6.4

[PATCH v3 04/10] drivers: pinctrl: add driver for Allwinner A64 SoC

[Andre Przywara]

Based on the Allwinner A64 user manual and on the previous sunxi
pinctrl drivers this introduces the pin multiplex assignments for
the ARMv8 Allwinner A64 SoC.
Port A is apparently used for the fixed function DRAM controller, so
the ports start at B here (the manual mentions "n from 1 to 7", so
not starting at 0).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
 arch/arm64/Kconfig.platforms                       |   1 +
 drivers/pinctrl/sunxi/Kconfig                      |   4 +
 drivers/pinctrl/sunxi/Makefile                     |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c         | 602 +++++++++++++++++++++
 5 files changed, 609 insertions(+)
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
index 9213b27..08b2361 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -21,6 +21,7 @@ Required properties:
   "allwinner,sun9i-a80-r-pinctrl"
   "allwinner,sun8i-a83t-pinctrl"
   "allwinner,sun8i-h3-pinctrl"
+  "allwinner,sun50i-a64-pinctrl"
 
 - reg: Should contain the register physical address and length for the
   pin controller.
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 97f5690..63a690d 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -74,6 +74,7 @@ config ARCH_SHMOBILE
 
 config ARCH_SUNXI
 	bool "Allwinner sunxi 64-bit SoC Family"
+	select PINCTRL_SUN50I_A64
 	help
 	  This enables support for Allwinner sunxi based SoCs like the A64.
 
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index f8dbc8b..c1f970f 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -64,4 +64,8 @@ config PINCTRL_SUN9I_A80_R
 	depends on RESET_CONTROLLER
 	select PINCTRL_SUNXI_COMMON
 
+config PINCTRL_SUN50I_A64
+	bool
+	select PINCTRL_SUNXI_COMMON
+
 endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index ef82f22..0ca7681 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_PINCTRL_SUN7I_A20)		+= pinctrl-sun7i-a20.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23)		+= pinctrl-sun8i-a23.o
 obj-$(CONFIG_PINCTRL_SUN8I_A23_R)	+= pinctrl-sun8i-a23-r.o
 obj-$(CONFIG_PINCTRL_SUN8I_A33)		+= pinctrl-sun8i-a33.o
+obj-$(CONFIG_PINCTRL_SUN50I_A64)	+= pinctrl-sun50i-a64.o
 obj-$(CONFIG_PINCTRL_SUN8I_A83T)	+= pinctrl-sun8i-a83t.o
 obj-$(CONFIG_PINCTRL_SUN8I_H3)		+= pinctrl-sun8i-h3.o
 obj-$(CONFIG_PINCTRL_SUN9I_A80)		+= pinctrl-sun9i-a80.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c
new file mode 100644
index 0000000..a53cc23
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c
@@ -0,0 +1,602 @@
+/*
+ * Allwinner A64 SoCs pinctrl driver.
+ *
+ * Copyright (C) 2016 - ARM Ltd.
+ * Author: Andre Przywara <andre.przywara@arm.com>
+ *
+ * Based on pinctrl-sun7i-a20.c, which is:
+ * Copyright (C) 2014 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin a64_pins[] = {
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* TX */
+		  SUNXI_FUNCTION(0x4, "jtag"),		/* MS0 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 0)),	/* EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RX */
+		  SUNXI_FUNCTION(0x4, "jtag"),		/* CK0 */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* VCCEN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 1)),		/* EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* RTS */
+		  SUNXI_FUNCTION(0x4, "jtag"),		/* DO0 */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* VPPEN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 2)),		/* EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart2"),		/* CTS */
+		  SUNXI_FUNCTION(0x3, "i2s0"),		/* MCLK */
+		  SUNXI_FUNCTION(0x4, "jtag"),		/* DI0 */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* VPPPP */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 3)),		/* EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif2"),		/* SYNC */
+		  SUNXI_FUNCTION(0x3, "i2s0"),		/* SYNC */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 4)),		/* EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif2"),		/* BCLK */
+		  SUNXI_FUNCTION(0x3, "i2s0"),		/* BCLK */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* DATA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 5)),		/* EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif2"),		/* DOUT */
+		  SUNXI_FUNCTION(0x3, "i2s0"),		/* DOUT */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* RST */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 6)),		/* EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif2"),		/* DIN */
+		  SUNXI_FUNCTION(0x3, "i2s0"),		/* DIN */
+		  SUNXI_FUNCTION(0x5, "sim"),		/* DET */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 7)),		/* EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x4, "uart0"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 8)),		/* EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(B, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x4, "uart0"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 0, 9)),		/* EINT9 */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NWE */
+		  SUNXI_FUNCTION(0x4, "spi0")),		/* MOSI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NALE */
+		  SUNXI_FUNCTION(0x3, "mmc2"),		/* DS */
+		  SUNXI_FUNCTION(0x4, "spi0")),		/* MISO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NCLE */
+		  SUNXI_FUNCTION(0x4, "spi0")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NCE1 */
+		  SUNXI_FUNCTION(0x4, "spi0")),		/* CS */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* NCE0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NRE# */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NRB0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* CMD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0")),	/* NRB1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ0 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ1 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ2 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ3 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ4 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ5 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ6 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQ7 */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "nand0"),		/* NDQS */
+		  SUNXI_FUNCTION(0x3, "mmc2")),		/* RST */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* TX */
+		  SUNXI_FUNCTION(0x4, "spi1"),		/* CS */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D3 */
+		  SUNXI_FUNCTION(0x3, "uart3"),		/* RX */
+		  SUNXI_FUNCTION(0x4, "spi1"),		/* CLK */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* DE */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D4 */
+		  SUNXI_FUNCTION(0x3, "uart4"),		/* TX */
+		  SUNXI_FUNCTION(0x4, "spi1"),		/* MOSI */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* HSYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D5 */
+		  SUNXI_FUNCTION(0x3, "uart4"),		/* RX */
+		  SUNXI_FUNCTION(0x4, "spi1"),		/* MISO */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* VSYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D6 */
+		  SUNXI_FUNCTION(0x3, "uart4"),		/* RTS */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D7 */
+		  SUNXI_FUNCTION(0x3, "uart4"),		/* CTS */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D10 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D11 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D12 */
+		  SUNXI_FUNCTION(0x4, "emac"),		/* ERXD3 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D13 */
+		  SUNXI_FUNCTION(0x4, "emac"),		/* ERXD2 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D14 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ERXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D15 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ERXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D18 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VP0 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ERXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D19 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VN0 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ERXCTL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D20 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VP1 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ENULL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D21 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VN1 */
+		  SUNXI_FUNCTION(0x4, "emac"),		/* ETXD3 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D22 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VP2 */
+		  SUNXI_FUNCTION(0x4, "emac"),		/* ETXD2 */
+		  SUNXI_FUNCTION(0x5, "ccir")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* D23 */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VN2 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ETXD1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 18),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VPC */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ETXD0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 19),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* DE */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VNC */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ETXCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 20),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* HSYNC */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VP3 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ETXCTL */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 21),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "lcd0"),		/* VSYNC */
+		  SUNXI_FUNCTION(0x3, "lvds0"),		/* VN3 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* ECLKIN */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 22),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "pwm"),		/* PWM0 */
+		  SUNXI_FUNCTION(0x4, "emac")),		/* EMDC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 23),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x4, "emac")),		/* EMDIO */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(D, 24),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* PCK */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* CLK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* CK */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* ERR */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* HSYNC */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* SYNC */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* VSYNC */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* DVLD */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D0 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D1 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D2 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D3 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D4 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D5 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D6 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0"),		/* D7 */
+		  SUNXI_FUNCTION(0x4, "ts0")),		/* D7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "csi0")),		/* SDA */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 14),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "pll"),		/* LOCK_DBG */
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SCK */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 15),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x3, "i2c2")),		/* SDA */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 16),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(E, 17),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D1 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* MSI */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D0 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DI1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CLK */
+		  SUNXI_FUNCTION(0x3, "uart0")),	/* TX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* CMD */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* DO1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D3 */
+		  SUNXI_FUNCTION(0x4, "uart0")),	/* RX */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc0"),		/* D2 */
+		  SUNXI_FUNCTION(0x3, "jtag")),		/* CK1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out")),
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)),	/* EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* CMD */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)),	/* EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D0 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)),	/* EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D1 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)),	/* EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D2 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)),	/* EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mmc1"),		/* D3 */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)),	/* EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)),	/* EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)),	/* EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)),	/* EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart1"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)),	/* EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif3"),		/* SYNC */
+		  SUNXI_FUNCTION(0x3, "i2s1"),		/* SYNC */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)),	/* EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif3"),		/* BCLK */
+		  SUNXI_FUNCTION(0x3, "i2s1"),		/* BCLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)),	/* EINT11 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif3"),		/* DOUT */
+		  SUNXI_FUNCTION(0x3, "i2s1"),		/* DOUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)),	/* EINT12 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "aif3"),		/* DIN */
+		  SUNXI_FUNCTION(0x3, "i2s1"),		/* DIN */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)),	/* EINT13 */
+	/* Hole */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SCK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 0)),	/* EINT0 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c0"),		/* SDA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 1)),	/* EINT1 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c1"),		/* SCK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 2)),	/* EINT2 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "i2c1"),		/* SDA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 3)),	/* EINT3 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart3"),		/* TX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 4)),	/* EINT4 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart3"),		/* RX */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 5)),	/* EINT5 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart3"),		/* RTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 6)),	/* EINT6 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "uart3"),		/* CTS */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 7)),	/* EINT7 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "spdif"),		/* OUT */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 8)),	/* EINT8 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 9)),	/* EINT9 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mic"),		/* CLK */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 10)),	/* EINT10 */
+	SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 11),
+		  SUNXI_FUNCTION(0x0, "gpio_in"),
+		  SUNXI_FUNCTION(0x1, "gpio_out"),
+		  SUNXI_FUNCTION(0x2, "mic"),		/* DATA */
+		  SUNXI_FUNCTION_IRQ_BANK(0x6, 2, 11)),	/* EINT11 */
+};
+
+static const struct sunxi_pinctrl_desc a64_pinctrl_data = {
+	.pins = a64_pins,
+	.npins = ARRAY_SIZE(a64_pins),
+	.irq_banks = 3,
+};
+
+static int a64_pinctrl_probe(struct platform_device *pdev)
+{
+	return sunxi_pinctrl_init(pdev,
+				  &a64_pinctrl_data);
+}
+
+static const struct of_device_id a64_pinctrl_match[] = {
+	{ .compatible = "allwinner,sun50i-a64-pinctrl", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, a64_pinctrl_match);
+
+static struct platform_driver a64_pinctrl_driver = {
+	.probe	= a64_pinctrl_probe,
+	.driver	= {
+		.name		= "sun50i-a64-pinctrl",
+		.of_match_table	= a64_pinctrl_match,
+	},
+};
+builtin_platform_driver(a64_pinctrl_driver);
-- 
2.6.4

[PATCH v3 05/10] DT: clk: sunxi: add binding doc for the multi-bus-gates clock

[Andre Przywara]

Recent Allwinner SoCs introduced a bus gates clock which can have
different parents for individual gates.
For the time being we encoded this relation in the driver.
This commit specifies a new binding which allows to encode this in
the DT by using a child node for each parent clock used. This allows
to specify any kind of relation efficiently and also keeps the very
same kernel driver for all SoCs at the same time.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/clock/sunxi.txt | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index c09f59b..323af8e 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -79,6 +79,7 @@ Required properties:
 	"allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
 	"allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
 	"allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
+	"allwinner,sunxi-multi-bus-gates-clk" - for the multi-parent bus gates
 
 Required properties for all clocks:
 - reg : shall be the control register address for the clock.
@@ -119,6 +120,11 @@ For "allwinner,sun6i-a31-pll6-clk", there are 2 outputs. The first output
 is the normal PLL6 output, or "pll6". The second output is rate doubled
 PLL6, or "pll6x2".
 
+The "allwinner,sunxi-multi-bus-gates-clk" holds the actual clocks in
+child nodes, where each one specifies the parent clock that the particular
+gates are depending from. The child nodes each follow the common clock
+binding as described in this document.
+
 The "allwinner,*-mmc-clk" clocks have three different outputs: the
 main clock, with the ID 0, and the output and sample clocks, with the
 IDs 1 and 2, respectively.
-- 
2.6.4

[PATCH v3 06/10] clk: sunxi: add generic multi-parent bus clock gates driver

[Andre Przywara]

The Allwinner H3 SoC introduced bus clock gates with potentially
different parents per clock gate. The H3 driver chose to hardcode the
actual parent clock relation in the code.
Add a new driver (which has the potential to drive the H3 and also
the simple clock gates as well) which uses the power of DT to describe
this relationship in an elegant and flexible way.
Using one subnode for every parent clock we get away with a single
DT compatible match, which can be used as a fallback value in the
actual DTs without the need to add specific compatible strings to the
code.  This avoids adding a new driver or function for every new SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
---
 drivers/clk/sunxi/Makefile          |   1 +
 drivers/clk/sunxi/clk-multi-gates.c | 105 ++++++++++++++++++++++++++++++++++++
 2 files changed, 106 insertions(+)
 create mode 100644 drivers/clk/sunxi/clk-multi-gates.c

diff --git a/drivers/clk/sunxi/Makefile b/drivers/clk/sunxi/Makefile
index 3fd7901..3a9dc31 100644
--- a/drivers/clk/sunxi/Makefile
+++ b/drivers/clk/sunxi/Makefile
@@ -11,6 +11,7 @@ obj-y += clk-a10-ve.o
 obj-y += clk-a20-gmac.o
 obj-y += clk-mod0.o
 obj-y += clk-simple-gates.o
+obj-y += clk-multi-gates.o
 obj-y += clk-sun8i-bus-gates.o
 obj-y += clk-sun8i-mbus.o
 obj-y += clk-sun9i-core.o
diff --git a/drivers/clk/sunxi/clk-multi-gates.c b/drivers/clk/sunxi/clk-multi-gates.c
new file mode 100644
index 0000000..76e715a
--- /dev/null
+++ b/drivers/clk/sunxi/clk-multi-gates.c
@@ -0,0 +1,105 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * Based on clk-sun8i-bus-gates.c, which is:
+ *  Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ * Based on clk-simple-gates.c, which is:
+ *  Copyright 2015 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+static DEFINE_SPINLOCK(gates_lock);
+
+static void __init sunxi_parse_parent(struct device_node *node,
+				      struct clk_onecell_data *clk_data,
+				      void __iomem *reg)
+{
+	const char *parent = of_clk_get_parent_name(node, 0);
+	const char *clk_name;
+	struct property *prop;
+	struct clk *clk;
+	const __be32 *p;
+	int index, i = 0;
+
+	of_property_for_each_u32(node, "clock-indices", prop, p, index) {
+		of_property_read_string_index(node, "clock-output-names",
+					      i, &clk_name);
+
+		clk = clk_register_gate(NULL, clk_name, parent, 0,
+					reg + 4 * (index / 32), index % 32,
+					0, &gates_lock);
+		i++;
+		if (IS_ERR(clk)) {
+			pr_warn("could not register gate clock \"%s\"\n",
+				clk_name);
+			continue;
+		}
+		if (clk_data->clks[index])
+			pr_warn("bus-gate clock %s: index #%d already registered as %s\n",
+				clk_name, index, "?");
+		else
+			clk_data->clks[index] = clk;
+	}
+}
+
+static void __init sunxi_multi_bus_gates_init(struct device_node *node)
+{
+	struct clk_onecell_data *clk_data;
+	struct device_node *child;
+	struct property *prop;
+	struct resource res;
+	void __iomem *reg;
+	const __be32 *p;
+	int number = 0;
+	int index;
+
+	reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+	if (IS_ERR(reg))
+		return;
+
+	clk_data = kmalloc(sizeof(struct clk_onecell_data), GFP_KERNEL);
+	if (!clk_data)
+		goto err_unmap;
+
+	for_each_child_of_node(node, child)
+		of_property_for_each_u32(child, "clock-indices", prop, p, index)
+			number = max(number, index);
+
+	clk_data->clks = kcalloc(number + 1, sizeof(struct clk *), GFP_KERNEL);
+	if (!clk_data->clks)
+		goto err_free_data;
+
+	for_each_child_of_node(node, child)
+		sunxi_parse_parent(child, clk_data, reg);
+
+	clk_data->clk_num = number + 1;
+	if (of_clk_add_provider(node, of_clk_src_onecell_get, clk_data))
+		pr_err("registering bus-gate clock %s failed\n", node->name);
+
+	return;
+
+err_free_data:
+	kfree(clk_data);
+err_unmap:
+	iounmap(reg);
+	of_address_to_resource(node, 0, &res);
+	release_mem_region(res.start, resource_size(&res));
+}
+
+CLK_OF_DECLARE(sunxi_multi_bus_gates, "allwinner,sunxi-multi-bus-gates-clk",
+	       sunxi_multi_bus_gates_init);
-- 
2.6.4

[PATCH v3 07/10] arm64: dts: add Allwinner A64 SoC .dtsi

[Andre Przywara]

The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
Changelog v1 .. v2:
- remove compatible string from the .dtsi
- amend compatible names to include sun50i
- drop PSCI 0.1 compatibility
- use lowercase hex digits in the GIC node too
- make pll6x2 an explicit fixed-factor clock
- make pll8 and pll8x2 proper clocks
- amend MMC clocks to match the manual, they are now mod0 clocks
- adapt MMC nodes to new MMC clocks
- add separate 4-pin and 2-pin definitions for the UARTs
- add I2C pins and driver nodes
- switch ahb_rst node to use normal compatible name, not the special,
  early-registration one.
Changelog v2 .. v3:
- remove leading zeros from node names' address part
- adapt PLL6/7/8 to proper PLL6 binding
- rename PLL6 to PLL7

 Documentation/devicetree/bindings/arm/sunxi.txt   |   1 +
 Documentation/devicetree/bindings/clock/sunxi.txt |   1 +
 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi     | 624 ++++++++++++++++++++++
 3 files changed, 626 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi

diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
index 7e79fcc..7e59d8b 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.txt
+++ b/Documentation/devicetree/bindings/arm/sunxi.txt
@@ -14,3 +14,4 @@ using one of the following compatible strings:
   allwinner,sun8i-a83t
   allwinner,sun8i-h3
   allwinner,sun9i-a80
+  allwinner,sun50i-a64
diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
index 323af8e..b7bd40d 100644
--- a/Documentation/devicetree/bindings/clock/sunxi.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi.txt
@@ -80,6 +80,7 @@ Required properties:
 	"allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
 	"allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
 	"allwinner,sunxi-multi-bus-gates-clk" - for the multi-parent bus gates
+	"allwinner,sun50i-a64-bus-gates-clk" - for the bus gates on A64
 
 Required properties for all clocks:
 - reg : shall be the control register address for the clock.
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
new file mode 100644
index 0000000..fb9c509
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -0,0 +1,624 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ * based on the Allwinner H3 dtsi:
+ *    Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+		};
+
+		cpu at 1 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+		};
+
+		cpu at 2 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+		};
+
+		cpu at 3 {
+			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x40000000 0>;
+	};
+
+	gic: interrupt-controller at 1c81000 {
+		compatible = "arm,gic-400";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+
+		reg = <0x01c81000 0x1000>,
+		      <0x01c82000 0x2000>,
+		      <0x01c84000 0x2000>,
+		      <0x01c86000 0x2000>;
+		interrupts = <GIC_PPI 9
+		      (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+
+		pll1: pll1_clk at 1c20000 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-a23-pll1-clk";
+			reg = <0x01c20000 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll1";
+		};
+
+		pll6: pll6_clk at 1c20028 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun6i-a31-pll6-clk";
+			reg = <0x01c20028 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll6", "pll6x2";
+		};
+
+		pll6d2: pll6d2_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <2>;
+			clock-mult = <1>;
+			clocks = <&pll6 0>;
+			clock-output-names = "pll6d2";
+		};
+
+		pll7: pll7_clk at 1c2002c {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun6i-a31-pll6-clk";
+			reg = <0x01c2002c 0x4>;
+			clocks = <&osc24M>;
+			clock-output-names = "pll7", "pll7x2";
+		};
+
+		cpu: cpu_clk at 1c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-cpu-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
+			clock-output-names = "cpu";
+			critical-clocks = <0>;
+		};
+
+		axi: axi_clk at 1c20050 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-axi-clk";
+			reg = <0x01c20050 0x4>;
+			clocks = <&cpu>;
+			clock-output-names = "axi";
+		};
+
+		ahb1: ahb1_clk at 1c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun6i-a31-ahb1-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
+			clock-output-names = "ahb1";
+		};
+
+		ahb2: ahb2_clk at 1c2005c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun8i-h3-ahb2-clk";
+			reg = <0x01c2005c 0x4>;
+			clocks = <&ahb1>, <&pll6d2>;
+			clock-output-names = "ahb2";
+		};
+
+		apb1: apb1_clk at 1c20054 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb0-clk";
+			reg = <0x01c20054 0x4>;
+			clocks = <&ahb1>;
+			clock-output-names = "apb1";
+		};
+
+		apb2: apb2_clk at 1c20058 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-apb1-clk";
+			reg = <0x01c20058 0x4>;
+			clocks = <&osc32k>, <&osc24M>, <&pll6 1>, <&pll6 1>;
+			clock-output-names = "apb2";
+		};
+
+		bus_gates: bus_gates_clk at 1c20060 {
+			#clock-cells = <1>;
+			compatible = "allwinner,sun50i-a64-bus-gates-clk",
+				     "allwinner,sunxi-multi-bus-gates-clk";
+			reg = <0x01c20060 0x14>;
+			ahb1_parent {
+				clocks = <&ahb1>;
+				clock-indices = <1>, <5>,
+						<6>, <8>,
+						<9>, <10>,
+						<13>, <14>,
+						<18>, <19>,
+						<20>, <21>,
+						<23>, <24>,
+						<25>, <28>,
+						<32>, <35>,
+						<36>, <37>,
+						<40>, <43>,
+						<44>, <52>,
+						<53>, <54>,
+						<135>;
+				clock-output-names = "bus_mipidsi", "bus_ce",
+						"bus_dma", "bus_mmc0",
+						"bus_mmc1", "bus_mmc2",
+						"bus_nand", "bus_sdram",
+						"bus_ts", "bus_hstimer",
+						"bus_spi0", "bus_spi1",
+						"bus_otg", "bus_otg_ehci0",
+						"bus_ehci0", "bus_otg_ohci0",
+						"bus_ve", "bus_lcd0",
+						"bus_lcd1", "bus_deint",
+						"bus_csi", "bus_hdmi",
+						"bus_de", "bus_gpu",
+						"bus_msgbox", "bus_spinlock",
+						"bus_dbg";
+			};
+			ahb2_parent {
+				clocks = <&ahb2>;
+				clock-indices = <17>, <29>;
+				clock-output-names = "bus_gmac", "bus_ohci0";
+			};
+			apb1_parent {
+				clocks = <&apb1>;
+				clock-indices = <64>, <65>,
+						<69>, <72>,
+						<76>, <77>,
+						<78>;
+				clock-output-names = "bus_codec", "bus_spdif",
+						"bus_pio", "bus_ths",
+						"bus_i2s0", "bus_i2s1",
+						"bus_i2s2";
+			};
+			abp2_parent {
+				clocks = <&apb2>;
+				clock-indices = <96>, <97>,
+						<98>, <101>,
+						<112>, <113>,
+						<114>, <115>,
+						<116>;
+				clock-output-names = "bus_i2c0", "bus_i2c1",
+						"bus_i2c2", "bus_scr",
+						"bus_uart0", "bus_uart1",
+						"bus_uart2", "bus_uart3",
+						"bus_uart4";
+			};
+		};
+
+		mmc0_clk: mmc0_clk at 1c20088 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-mod0-clk";
+			reg = <0x01c20088 0x4>;
+			clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+			clock-output-names = "mmc0";
+                };
+
+		mmc1_clk: mmc1_clk at 1c2008c {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-mod0-clk";
+			reg = <0x01c2008c 0x4>;
+			clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+			clock-output-names = "mmc1";
+		};
+
+		mmc2_clk: mmc2_clk at 1c20090 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun4i-a10-mod0-clk";
+			reg = <0x01c20090 0x4>;
+			clocks = <&osc24M>, <&pll6 1>, <&pll7 1>;
+			clock-output-names = "mmc2";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mmc0: mmc at 1c0f000 {
+			compatible = "allwinner,sun50i-a64-mmc",
+				     "allwinner,sun5i-a13-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&bus_gates 8>, <&mmc0_clk>,
+				 <&mmc0_clk>, <&mmc0_clk>;
+			clock-names = "ahb", "mmc",
+				      "output", "sample";
+			resets = <&ahb_rst 8>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc at 1c10000 {
+			compatible = "allwinner,sun50i-a64-mmc",
+				     "allwinner,sun5i-a13-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&bus_gates 9>, <&mmc1_clk>,
+				 <&mmc1_clk>, <&mmc1_clk>;
+			clock-names = "ahb", "mmc",
+				      "output", "sample";
+			resets = <&ahb_rst 9>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc at 1c11000 {
+			compatible = "allwinner,sun50i-a64-mmc",
+				     "allwinner,sun5i-a13-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&bus_gates 10>, <&mmc2_clk>,
+				 <&mmc2_clk>, <&mmc2_clk>;
+			clock-names = "ahb", "mmc",
+				      "output", "sample";
+			resets = <&ahb_rst 10>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		pio: pinctrl at 1c20800 {
+			compatible = "allwinner,sun50i-a64-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 69>;
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			uart0_pins_a: uart0 at 0 {
+				allwinner,pins = "PB8", "PB9";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart0_pins_b: uart0 at 1 {
+				allwinner,pins = "PF2", "PF3";
+				allwinner,function = "uart0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart1_2pins: uart1_2 at 0 {
+				allwinner,pins = "PG6", "PG7";
+				allwinner,function = "uart1";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart1_4pins: uart1_4 at 0 {
+				allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+				allwinner,function = "uart1";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart2_2pins: uart2_2 at 0 {
+				allwinner,pins = "PB0", "PB1";
+				allwinner,function = "uart2";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart2_4pins: uart2_4 at 0 {
+				allwinner,pins = "PB0", "PB1", "PB2", "PB3";
+				allwinner,function = "uart2";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart3_pins_a: uart3 at 0 {
+				allwinner,pins = "PD0", "PD1";
+				allwinner,function = "uart3";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart3_2pins_b: uart3_2 at 1 {
+				allwinner,pins = "PH4", "PH5";
+				allwinner,function = "uart3";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart3_4pins_b: uart3_4 at 1 {
+				allwinner,pins = "PH4", "PH5", "PH6", "PH7";
+				allwinner,function = "uart3";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart4_2pins: uart4_2 at 0 {
+				allwinner,pins = "PD2", "PD3";
+				allwinner,function = "uart4";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart4_4pins: uart4_4 at 0 {
+				allwinner,pins = "PD2", "PD3", "PD4", "PD5";
+				allwinner,function = "uart4";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_pins: mmc0 at 0 {
+				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
+						 "PF4", "PF5";
+				allwinner,function = "mmc0";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc0_default_cd_pin: mmc0_cd_pin at 0 {
+				allwinner,pins = "PF6";
+				allwinner,function = "gpio_in";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+			};
+
+			mmc1_pins: mmc1 at 0 {
+				allwinner,pins = "PG0", "PG1", "PG2", "PG3",
+						 "PG4", "PG5";
+				allwinner,function = "mmc1";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			mmc2_pins: mmc2 at 0 {
+				allwinner,pins = "PC1", "PC5", "PC6", "PC8",
+						 "PC9", "PC10";
+				allwinner,function = "mmc2";
+				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			i2c0_pins: i2c0_pins {
+				allwinner,pins = "PH0", "PH1";
+				allwinner,function = "i2c0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			i2c1_pins: i2c1_pins {
+				allwinner,pins = "PH2", "PH3";
+				allwinner,function = "i2c1";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			i2c2_pins: i2c2_pins {
+				allwinner,pins = "PE14", "PE15";
+				allwinner,function = "i2c2";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+		};
+
+		ahb_rst: reset at 1c202c0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202c0 0xc>;
+		};
+
+		apb1_rst: reset at 1c202d0 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d0 0x4>;
+		};
+
+		apb2_rst: reset at 1c202d8 {
+			#reset-cells = <1>;
+			compatible = "allwinner,sun6i-a31-clock-reset";
+			reg = <0x01c202d8 0x4>;
+		};
+
+		uart0: serial at 1c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 112>;
+			resets = <&apb2_rst 16>;
+			status = "disabled";
+		};
+
+		uart1: serial at 1c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 113>;
+			resets = <&apb2_rst 17>;
+			status = "disabled";
+		};
+
+		uart2: serial at 1c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 114>;
+			resets = <&apb2_rst 18>;
+			status = "disabled";
+		};
+
+		uart3: serial at 1c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 115>;
+			resets = <&apb2_rst 19>;
+			status = "disabled";
+		};
+
+		uart4: serial at 1c29000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&bus_gates 116>;
+			resets = <&apb2_rst 20>;
+			status = "disabled";
+		};
+
+		rtc: rtc at 1f00000 {
+			compatible = "allwinner,sun6i-a31-rtc";
+			reg = <0x01f00000 0x54>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c0: i2c at 1c2ac00 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2ac00 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 96>;
+			resets = <&apb2_rst 0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c at 1c2b000 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 97>;
+			resets = <&apb2_rst 1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c at 1c2b400 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b400 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bus_gates 98>;
+			resets = <&apb2_rst 2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.6.4

[PATCH v3 08/10] of: add vendor prefix for Pine64

[Andre Przywara]

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 72e2c5a..0c22fa9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -175,6 +175,7 @@ parade	Parade Technologies Inc.
 pericom	Pericom Technology Inc.
 phytec	PHYTEC Messtechnik GmbH
 picochip	Picochip Ltd
+pine64	Pine64
 plathome	Plat'Home Co., Ltd.
 plda	PLDA
 pixcir  PIXCIR MICROELECTRONICS Co., Ltd
-- 
2.6.4

[PATCH v3 09/10] arm64: dts: add Pine64 support

[Andre Przywara]

The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
Changelog v1 .. v2:
- move aliases node into the common board DT file
- move fixed MMC regulator into the common board DT file
- drop UARTs 1-4 nodes from the default DT
- add I2C node (pins seem to be dedicated to I2C)

 arch/arm64/boot/dts/Makefile                       |  1 +
 arch/arm64/boot/dts/allwinner/Makefile             |  5 ++
 .../dts/allwinner/sun50i-a64-pine64-common.dtsi    | 80 ++++++++++++++++++++++
 .../boot/dts/allwinner/sun50i-a64-pine64-plus.dts  | 59 ++++++++++++++++
 .../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 58 ++++++++++++++++
 5 files changed, 203 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/Makefile
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts

diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index f832b8a..3b7428a 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -1,3 +1,4 @@
+dts-dirs += allwinner
 dts-dirs += altera
 dts-dirs += amd
 dts-dirs += apm
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
new file mode 100644
index 0000000..1e29a5a
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -0,0 +1,5 @@
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+
+always		:= $(dtb-y)
+subdir-y	:= $(dts-dirs)
+clean-files	:= *.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi
new file mode 100644
index 0000000..d5a7249
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi
@@ -0,0 +1,80 @@
+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun50i-a64.dtsi"
+
+/ {
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc {
+		reg_vcc3v3: vcc3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "vcc3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>, <&mmc0_default_cd_pin>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 0>;
+	cd-inverted;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
new file mode 100644
index 0000000..549dc15
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64-pine64-common.dtsi"
+
+/ {
+	model = "Pine64+";
+	compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* There is a model with 2GB of DRAM, but U-Boot fixes this for us. */
+	memory {
+		reg = <0x40000000 0x40000000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
new file mode 100644
index 0000000..ebe029e
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -0,0 +1,58 @@
+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64-pine64-common.dtsi"
+
+/ {
+	model = "Pine64";
+	compatible = "pine64,pine64", "allwinner,sun50i-a64";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x40000000 0x20000000>;
+	};
+};
-- 
2.6.4

[PATCH v3 10/10] arm64: add defconfig options for Allwinner SoCs

[Andre Przywara]

With the Allwinner platform now supported, enable it in the defconfig
and add some options to give some decent out-of-the-box experience on
those SoCs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/configs/defconfig | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 18ca9fb..7acadce 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -31,6 +31,7 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_ARCH_SUNXI=y
 CONFIG_ARCH_BCM_IPROC=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_EXYNOS7=y
@@ -135,12 +136,15 @@ CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_VIRTIO_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MV64XXX=y
 CONFIG_I2C_QUP=y
 CONFIG_I2C_RCAR=y
 CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_SPI_QUP=y
 CONFIG_PINCTRL_MSM8916=y
+CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
 CONFIG_GPIO_RCAR=y
 CONFIG_GPIO_XGENE=y
@@ -175,10 +179,12 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_TEGRA=y
 CONFIG_MMC_SPI=y
+CONFIG_MMC_SUNXI=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_DW_IDMAC=y
 CONFIG_MMC_DW_PLTFM=y
 CONFIG_MMC_DW_EXYNOS=y
+CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_SYSCON=y
@@ -187,6 +193,7 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_EFI=y
+CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_XGENE=y
 CONFIG_DMADEVICES=y
 CONFIG_RCAR_DMAC=y
-- 
2.6.4

[PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support

[Andre Przywara]

Hi Maxime,

can you give me a quick assessment on how we can progress from here?

Is it already too late for at least some of the patches to go into 4.6?
If not, can you at least merge the Kconfig patch (3/10) and the pinctrl
driver (if that goes via your tree at all)? Do you need more reviews or
Acks?
Of the prerequisite patches for a clean arm64 compile I see that the
sunxi-rsb is in your for-next branch, but not in -next itself. Also I
got a message about the sunxi-ss Kconfig patch to be applied, but cannot
find it in -next either. All the other patches have made it into -next
as of today.

Also are you happy with the PLL6 reuse patch I sent on Monday and can I
base the A64's PLL7 clock on that?
Or do you prefer another approach here? I am happy to discuss this on
the list then.

Cheers,
Andre.

On 22/02/16 18:20, Andre Przywara wrote:
> Hi,
> 
> another update of the Allwinner A64 / Pine64 support series.
> I added a solution for the PLL6 reuse issue (the same patch I posted
> yesterday). Also I addressed the comments I got from Rob and Chen-Yu.
> For a changelog see below.
> 
> This series provides initial support for the Allwinner A64 SoC,
> which is based on four ARM Cortex-A53 cores implementing the ARMv8
> 64-bit architecture.
> On top of this there is also initial support for the Pine64 board,
> for which you can find more information and links in the linux-sunxi
> Wiki [1].
> The resulting kernel boots fine on my development samples I have
> here, though the actual boot process is a bit involved at the moment.
> You can find more information and a ready-to-flash image here [2].
> 
> Patch 1/10 removes the hardcoded "pll6" name for the PLL6 clock, so
> it can be reused for the A64's PLL7, patch 2/10 uses that facility
> for the Allwinner H3 SoC's PLL8.
> Patch 3/10 enables the Allwinner/sunxi platform for the arm64
> architecture, so one can select the required drivers during
> configuration.
> Patch 4/10 adds the pinctrl driver, which has been on the list before.
> Patch 5 and 6 add a new generic driver for the bus clock gates which
> relies on DT for providing the parent relationship. That makes adding
> new SoCs much easier, since there should be no more kernel code
> changes necessary.
> Patch 7-9 add the new vendor name and the device tree files, the former
> for the SoC itself, the latter for the Pine64 boards.
> The final patch 10 updates defconfig, so that the generic arm64 kernel
> supports the basic SoC drivers out of the box.
> 
> In the moment we support the basic peripherals like GIC, timer, clocks,
> GPIOs, UARTs and (since v2) I2C.
> The MMC IP block has changed a bit compared to previous SoCs, so the
> existing driver is not 100% compatible. However the default delays seem
> to work fine for the SD cards, so I included all the necessary bits in
> here, since working MMC makes this series indefinitely more usable.
> We can fix both the MMC driver and the DT in a compatible way later.
> 
> Please have a look and comment on the patches. We might want to split
> the series if some patches seem too controversial for being merged
> soonish, please let me know if this is the case and I am happy to
> rearrange the series.
> 
> The patches are based on mripard/sunxi/for-next (since linux-next is
> a bit messy atm). A working repo can be found over here[3].
> 
> Cheers,
> Andre
> 
> Changelog v1 .. v2:
> - Change the naming of DT nodes, identifiers and file names to include
>   the wonderful Allwinner architecture prefix everywhere. You asked
>   for it, you got it, enjoy!
> - Drop SUNXI_MMC to be selected automatically, instead put it in the
>   defconfig.
> - Add a binding documentation for the new multi-bus-gates driver.
> - Add a defconfig update patch.
> - Lots of changes in the DTs, see the respective patches for details.
> 
> Changelog v2 .. v3:
> - Reordered sunxi section in ARM64 platform config.
> - Add PLL6 reuse patch and rework the .dtsi to use the existing binding.
> - Drop unneeded module boilerplate for the pinctrl driver.
> - Rename "owa" pin to "spdif".
> - Rename pll8 to pll7 in the DT.
> - Remove leading 0 in DT node address parts.
> - Added Acks from Rob.
> 
> [1] http://linux-sunxi.org/Pine64
> [2] https://github.com/apritzel/pine64
> [3] https://github.com/apritzel/linux/commits/a64-v3
> 
> Andre Przywara (10):
>   clk: sunxi: allow PLL6 clock to be reused
>   ARM: dts: sunxi: make PLL8 in the H3 a proper clock
>   arm64: Introduce Allwinner SoC config option
>   drivers: pinctrl: add driver for Allwinner A64 SoC
>   DT: clk: sunxi: add binding doc for the multi-bus-gates clock
>   clk: sunxi: add generic multi-parent bus clock gates driver
>   arm64: dts: add Allwinner A64 SoC .dtsi
>   of: add vendor prefix for Pine64
>   arm64: dts: add Pine64 support
>   arm64: add defconfig options for Allwinner SoCs
> 
>  Documentation/devicetree/bindings/arm/sunxi.txt    |   1 +
>  Documentation/devicetree/bindings/clock/sunxi.txt  |   7 +
>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>  .../devicetree/bindings/vendor-prefixes.txt        |   1 +
>  arch/arm/boot/dts/sun8i-h3.dtsi                    |  18 +-
>  arch/arm64/Kconfig.platforms                       |   6 +
>  arch/arm64/boot/dts/Makefile                       |   1 +
>  arch/arm64/boot/dts/allwinner/Makefile             |   5 +
>  .../dts/allwinner/sun50i-a64-pine64-common.dtsi    |  80 +++
>  .../boot/dts/allwinner/sun50i-a64-pine64-plus.dts  |  59 ++
>  .../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts |  58 ++
>  arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi      | 624 +++++++++++++++++++++
>  arch/arm64/configs/defconfig                       |   7 +
>  drivers/clk/sunxi/Makefile                         |   1 +
>  drivers/clk/sunxi/clk-factors.c                    |   3 +-
>  drivers/clk/sunxi/clk-factors.h                    |   1 +
>  drivers/clk/sunxi/clk-multi-gates.c                | 105 ++++
>  drivers/clk/sunxi/clk-sunxi.c                      |   4 +-
>  drivers/pinctrl/sunxi/Kconfig                      |   4 +
>  drivers/pinctrl/sunxi/Makefile                     |   1 +
>  drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c         | 602 ++++++++++++++++++++
>  21 files changed, 1577 insertions(+), 12 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/allwinner/Makefile
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-common.dtsi
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-plus.dts
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
>  create mode 100644 drivers/clk/sunxi/clk-multi-gates.c
>  create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-a64.c
> 

[PATCH v3 04/10] drivers: pinctrl: add driver for Allwinner A64 SoC

[Maxime Ripard]

Hi,

On Mon, Feb 22, 2016 at 06:20:49PM +0000, Andre Przywara wrote:
> Based on the Allwinner A64 user manual and on the previous sunxi
> pinctrl drivers this introduces the pin multiplex assignments for
> the ARMv8 Allwinner A64 SoC.
> Port A is apparently used for the fixed function DRAM controller, so
> the ports start at B here (the manual mentions "n from 1 to 7", so
> not starting at 0).
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Linus, could you merge this patch for 4.6?

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160225/f0ca1553/attachment-0001.sig>

[PATCH v3 10/10] arm64: add defconfig options for Allwinner SoCs

[Maxime Ripard]

On Mon, Feb 22, 2016 at 06:20:55PM +0000, Andre Przywara wrote:
> With the Allwinner platform now supported, enable it in the defconfig
> and add some options to give some decent out-of-the-box experience on
> those SoCs.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Applied, thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160225/d891d8bc/attachment.sig>

[PATCH v3 00/10] arm64: Introduce Allwinner A64 and Pine64 support

[Maxime Ripard]

Hi,

On Thu, Feb 25, 2016 at 10:04:59AM +0000, Andre Przywara wrote:
> Hi Maxime,
> 
> can you give me a quick assessment on how we can progress from here?
> 
> Is it already too late for at least some of the patches to go into 4.6?

I think we still have a major disagreement on the clocks part, and
yeah, it's too late for 4.6, I'm going to send the PR tomorrow, and am
merging the final patches that didn't have the attention they deserved
lately.

> If not, can you at least merge the Kconfig patch (3/10)

This one was already merged

> and the pinctrl driver (if that goes via your tree at all)? Do you
> need more reviews or Acks?

And I just gave my Acked-by for this one, but it will go through the
pinctrl tree, hopefully in time.

> Of the prerequisite patches for a clean arm64 compile I see that the
> sunxi-rsb is in your for-next branch, but not in -next itself. Also I
> got a message about the sunxi-ss Kconfig patch to be applied, but cannot
> find it in -next either. All the other patches have made it into -next
> as of today.

Great, I'll push the A64 kconfig patch in next today, and see if
there's any fallout.

> Also are you happy with the PLL6 reuse patch I sent on Monday and can I
> base the A64's PLL7 clock on that?
> Or do you prefer another approach here? I am happy to discuss this on
> the list then.

I just commented on it.

Sorry for the unresponsiveness lately,
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160225/5d167351/attachment-0001.sig>

[PATCH v3 04/10] drivers: pinctrl: add driver for Allwinner A64 SoC

[Linus Walleij]

On Tue, Feb 23, 2016 at 1:20 AM, Andre Przywara <andre.przywara@arm.com> wrote:

> Based on the Allwinner A64 user manual and on the previous sunxi
> pinctrl drivers this introduces the pin multiplex assignments for
> the ARMv8 Allwinner A64 SoC.
> Port A is apparently used for the fixed function DRAM controller, so
> the ports start at B here (the manual mentions "n from 1 to 7", so
> not starting at 0).
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>

Add Maxime's ACK.

This does not apply do the pinctrl devel branch, so please rebase it.

>  .../bindings/pinctrl/allwinner,sunxi-pinctrl.txt   |   1 +
>  arch/arm64/Kconfig.platforms                       |   1 +

Remove this from the patch, it can go in through the ASoC or ARM64 tree,
just a symbol dependence is fine to merge orthogonally.

Yours,
Linus Walleij