[PATCH] ARM: dts: DRA7: change address-cells and size-cells

[a0131933@ti.com (Lokesh Vutla)]

Hi Tony,

On Saturday 27 February 2016 12:41 AM, Tony Lindgren wrote:
> * Lokesh Vutla <lokeshvutla@ti.com> [160224 02:14]:
>> DRA7 SoC has the capability to support DDR memory upto 4GB. In order to
>> represent this in memory dt node, the address-cells and size cells
>> should be 2. So, changing the address-cells and size-cells to 2 and
>> updating the memory nodes accordingly.
>> @@ -57,10 +57,10 @@
>>  		compatible = "arm,cortex-a15-gic";
>>  		interrupt-controller;
>>  		#interrupt-cells = <3>;
>> -		reg = <0x48211000 0x1000>,
>> -		      <0x48212000 0x1000>,
>> -		      <0x48214000 0x2000>,
>> -		      <0x48216000 0x2000>;
>> +		reg = <0x0 0x48211000 0x0 0x1000>,
>> +		      <0x0 0x48212000 0x0 0x1000>,
>> +		      <0x0 0x48214000 0x0 0x2000>,
>> +		      <0x0 0x48216000 0x0 0x2000>;
>>  		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
>>  		interrupt-parent = <&gic>;
>>  	};
>> @@ -69,7 +69,7 @@
>>  		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
>>  		interrupt-controller;
>>  		#interrupt-cells = <3>;
>> -		reg = <0x48281000 0x1000>;
>> +		reg = <0x0 0x48281000 0x0 0x1000>;
>>  		interrupt-parent = <&gic>;
>>  	};
>>  
>> @@ -96,10 +96,10 @@
>>  		compatible = "ti,dra7-l3-noc", "simple-bus";
>>  		#address-cells = <1>;
>>  		#size-cells = <1>;
>> -		ranges;
>> +		ranges = <0x0 0x0 0x0 0xc0000000>;
>>  		ti,hwmods = "l3_main_1", "l3_main_2";
>> -		reg = <0x44000000 0x1000000>,
>> -		      <0x45000000 0x1000>;
>> +		reg = <0x0 0x44000000 0x0 0x1000000>,
>> +		      <0x0 0x45000000 0x0 0x1000>;
>>  		interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
>>  				      <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>>  
> 
> Is size-cells 2 needed for all these devices too? Can't
> you just set it for the memory nodes?

For updating memory nodes with 64bit, I have to change the address and
size cells as 2 for the root node. So, reg property in all the children
to the root node should also be updated with 2 address cells and 2 size
cells or else the below warning shows up:

Warning (reg_format): "reg" property in /interrupt-controller at 48281000
has invalid length (8 bytes) (#address-cells == 2, #size-cells == 2)
Warning (ranges_format): /ocp has empty "ranges" property but its
#address-cells (1) differs from / (2)
Warning (ranges_format): /ocp has empty "ranges" property but its
#size-cells (1) differs from / (2)

This is why I am updating all the children to the root node.

Thanks and regards,
Lokesh