From: jh80.chung@samsung.com (Jaehoon Chung)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 09/10] ARM: dts: Add MSHC2 dt node for SD card for exynos3250-artik5-devel board
Date: Tue, 15 Mar 2016 09:56:33 +0900 [thread overview]
Message-ID: <56E75DC1.7000807@samsung.com> (raw)
In-Reply-To: <56E7567B.40301@samsung.com>
On 03/15/2016 09:25 AM, Krzysztof Kozlowski wrote:
> On 14.03.2016 19:22, Chanwoo Choi wrote:
>> On 2016? 03? 14? 18:44, Krzysztof Kozlowski wrote:
>>> On 14.03.2016 17:48, Chanwoo Choi wrote:
>>>> On 2016? 03? 14? 17:31, Krzysztof Kozlowski wrote:
>>>>> On 14.03.2016 11:04, Chanwoo Choi wrote:
>>>>>> From: Jaehoon Chung <jh80.chung@samsung.com>
>>>>>>
>>>>>> This patch adds MSHC (Mobile Storage Host Controller) dt node for
>>>>>> Exynos3250 SoC. MSHC is an interface between the system and the SD card
>>>>>>
>>>>>> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
>>>>>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>>>>>> ---
>>>>>> arch/arm/boot/dts/exynos3250-artik5-devel.dts | 16 ++++++++++++++++
>>>>>> 1 file changed, 16 insertions(+)
>>>>>>
>>>>>> diff --git a/arch/arm/boot/dts/exynos3250-artik5-devel.dts b/arch/arm/boot/dts/exynos3250-artik5-devel.dts
>>>>>> index d17c28969118..a371baf8536d 100644
>>>>>> --- a/arch/arm/boot/dts/exynos3250-artik5-devel.dts
>>>>>> +++ b/arch/arm/boot/dts/exynos3250-artik5-devel.dts
>>>>>> @@ -21,6 +21,22 @@
>>>>>> "samsung,exynos3250", "samsung,exynos3";
>>>>>> };
>>>>>>
>>>>>> +&mshc_2 {
>>>>>> + num-slots = <1>;
>>>>>> + cap-sd-highspeed;
>>>>>> + disable-wp;
>>>>>> + card-detect-delay = <200>;
>>>>>> + clock-frequency = <100000000>;
>>>>>> + clock-freq-min-max = <400000 100000000>;
>>>>>> + samsung,dw-mshc-ciu-div = <1>;
>>>>>> + samsung,dw-mshc-sdr-timing = <0 1>;
>>>>>> + samsung,dw-mshc-ddr-timing = <1 2>;
>>>>>> + pinctrl-names = "default";
>>>>>> + pinctrl-0 = <&sd2_cmd &sd2_clk &sd2_cd &sd2_bus1 &sd2_bus4>;
>>>>>> + bus-width = <4>;
>>>>>> + status = "okay";
>>>>>
>>>>> vqmmc-supply = ldo3?
>>>>
>>>> ldo3 is always on state because ldo3 is used for various IP in exynos3250.
>>>> I think that we had better to remain always on state for ldo3.
>>>
>>> Yes, I wasn't thinking about toggling ldo3 but about taking the
>>> regulator here to model the dependencies between components.
>>
>> Okay. I'll add it as following:
>>
>> vmmc-supply = <&ldo18_reg>;
>> vqmmc-supply = <&ldo3>;
>
> ldo18 is not used by mshc2. At least my schematics show that LDO3 goes
> to DVDD_MMC2 (on different board revision that would be ldo18 instead of
> ldo3, but not both).
It's confusing..but it seems that Krzysztof's opinion is right.
Best Regards,
Jaehoon Chung
>
> The card itself is powered by VDDFLASH_28/MAIN_BAT.
>
> BR,
> Krzysztof
>
>
next prev parent reply other threads:[~2016-03-15 0:56 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-14 2:04 [PATCH 00/10] ARM: dts: Add new Exynos3250-based ARTIK5 module dtsi file Chanwoo Choi
2016-03-14 2:04 ` [PATCH 01/10] clk: samsung: exynos3250: Add UART2 clock Chanwoo Choi
2016-03-14 2:04 ` [PATCH 02/10] clk: samsung: exynos3250: Add MMC2 clock Chanwoo Choi
2016-03-14 2:04 ` [PATCH 03/10] ARM: dts: Add UART2 dt node for Exynos3250 SoC Chanwoo Choi
2016-03-14 2:04 ` [PATCH 04/10] ARM: dts: Add MSHC2 " Chanwoo Choi
2016-03-14 6:22 ` Krzysztof Kozlowski
2016-03-14 8:28 ` Chanwoo Choi
2016-03-14 9:52 ` Krzysztof Kozlowski
2016-03-14 2:04 ` [PATCH 05/10] ARM: dts: Add exynos3250-artik5 dtsi file for ARTIK5 module Chanwoo Choi
2016-03-14 6:42 ` Krzysztof Kozlowski
2016-03-14 6:57 ` Chanwoo Choi
2016-03-14 7:22 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 06/10] ARM: dts: Add MSHC0 dt node for eMMC device for exynos3250-artik5 module Chanwoo Choi
2016-03-14 6:57 ` Krzysztof Kozlowski
2016-03-14 8:15 ` Chanwoo Choi
2016-03-14 9:59 ` Krzysztof Kozlowski
2016-03-14 2:04 ` [PATCH 06/10] ARM: dts: exynos3250-artik5: Add MSHC0 dt node for eMMC device Chanwoo Choi
2016-03-14 2:10 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 07/10] ARM: dts: Add thermal zone and cpufreq node for exynos3250-artik5 module Chanwoo Choi
2016-03-14 7:06 ` Krzysztof Kozlowski
2016-03-14 7:13 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 08/10] ARM: dts: Add rtc and adc dt " Chanwoo Choi
2016-03-14 7:12 ` Krzysztof Kozlowski
2016-03-14 7:21 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 09/10] ARM: dts: Add MSHC2 dt node for SD card for exynos3250-artik5-devel board Chanwoo Choi
2016-03-14 8:31 ` Krzysztof Kozlowski
2016-03-14 8:48 ` Chanwoo Choi
2016-03-14 9:44 ` Krzysztof Kozlowski
2016-03-14 10:22 ` Chanwoo Choi
2016-03-15 0:25 ` Krzysztof Kozlowski
2016-03-15 0:56 ` Jaehoon Chung [this message]
2016-03-15 1:45 ` Chanwoo Choi
2016-03-15 1:46 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 10/10] ARM: dts: Add PPMU node for exynos3250-artik5 module Chanwoo Choi
2016-03-14 8:34 ` Krzysztof Kozlowski
2016-03-14 8:43 ` Chanwoo Choi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56E75DC1.7000807@samsung.com \
--to=jh80.chung@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).