* [PATCH RFT v8 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs " Duje Mihanović
` (4 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović, Bartosz Golaszewski
Sharp's Spitz board still uses the legacy GPIO interface for controlling
a GPIO pin related to the USB host controller.
Convert this function to use the new GPIO descriptor interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/spitz.c | 13 ++++++-------
drivers/usb/host/ohci-pxa27x.c | 5 +++++
2 files changed, 11 insertions(+), 7 deletions(-)
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index cc691b199429..535e2b2e997b 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
* USB Host
******************************************************************************/
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
+ SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
+
static int spitz_ohci_init(struct device *dev)
{
- int err;
-
- err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
- if (err)
- return err;
+ gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
/* Only Port 2 is connected, setup USB Port 2 Output Control Register */
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
- return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
+ return 0;
}
static void spitz_ohci_exit(struct device *dev)
{
- gpio_free(SPITZ_GPIO_USB_HOST);
+ gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
}
static struct pxaohci_platform_data spitz_ohci_platform_data = {
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 357d9aee38a3..a809ba0bb25e 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -121,6 +121,7 @@ struct pxa27x_ohci {
void __iomem *mmio_base;
struct regulator *vbus[3];
bool vbus_enabled[3];
+ struct gpio_desc *usb_host;
};
#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
@@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
pxa_ohci = to_pxa27x_ohci(hcd);
pxa_ohci->clk = usb_clk;
pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
+ pxa_ohci->usb_host = devm_gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
+ if (IS_ERR(pxa_ohci->usb_host))
+ return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host),
+ "failed to get USB host GPIO\n");
for (i = 0; i < 3; ++i) {
char name[6];
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
2023-10-11 14:21 ` Bartosz Golaszewski
2023-10-11 13:23 ` [PATCH RFT v8 3/6] ARM: pxa: Convert Spitz CF power control " Duje Mihanović
` (3 subsequent siblings)
5 siblings, 1 reply; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović
Sharp's Spitz board still uses the legacy GPIO interface for configuring
its two onboard LEDs.
Convert them to use the GPIO descriptor interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/spitz.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 535e2b2e997b..9efd603c715a 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
* LEDs
******************************************************************************/
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpiod_lookup_table spitz_led_gpio_table = {
+ .dev_id = "leds-gpio",
+ .table = {
+ GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
+ GPIO_ACTIVE_HIGH),
+ GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
+ GPIO_ACTIVE_HIGH),
+ { }
+ }
+};
+
static struct gpio_led spitz_gpio_leds[] = {
{
.name = "spitz:amber:charge",
.default_trigger = "sharpsl-charge",
- .gpio = SPITZ_GPIO_LED_ORANGE,
},
{
.name = "spitz:green:hddactivity",
.default_trigger = "disk-activity",
- .gpio = SPITZ_GPIO_LED_GREEN,
},
};
@@ -480,6 +489,7 @@ static struct platform_device spitz_led_device = {
static void __init spitz_leds_init(void)
{
+ gpiod_add_lookup_table(&spitz_led_gpio_table);
platform_device_register(&spitz_led_device);
}
#else
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors
2023-10-11 13:23 ` [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs " Duje Mihanović
@ 2023-10-11 14:21 ` Bartosz Golaszewski
2023-10-11 15:17 ` Duje Mihanović
0 siblings, 1 reply; 10+ messages in thread
From: Bartosz Golaszewski @ 2023-10-11 14:21 UTC (permalink / raw)
To: Duje Mihanović
Cc: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij, Andy Shevchenko,
Dmitry Torokhov, Mark Brown, linux-arm-kernel, linux-kernel,
linux-usb, linux-gpio, linux-input, linux-spi
On Wed, Oct 11, 2023 at 3:24 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for configuring
> its two onboard LEDs.
>
> Convert them to use the GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---
> arch/arm/mach-pxa/spitz.c | 14 ++++++++++++--
> 1 file changed, 12 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index 535e2b2e997b..9efd603c715a 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
> * LEDs
> ******************************************************************************/
> #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
> +static struct gpiod_lookup_table spitz_led_gpio_table = {
> + .dev_id = "leds-gpio",
> + .table = {
> + GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
> + GPIO_ACTIVE_HIGH),
> + GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
> + GPIO_ACTIVE_HIGH),
> + { }
> + }
> +};
> +
> static struct gpio_led spitz_gpio_leds[] = {
> {
> .name = "spitz:amber:charge",
> .default_trigger = "sharpsl-charge",
> - .gpio = SPITZ_GPIO_LED_ORANGE,
> },
> {
> .name = "spitz:green:hddactivity",
> .default_trigger = "disk-activity",
> - .gpio = SPITZ_GPIO_LED_GREEN,
> },
> };
>
> @@ -480,6 +489,7 @@ static struct platform_device spitz_led_device = {
>
> static void __init spitz_leds_init(void)
> {
> + gpiod_add_lookup_table(&spitz_led_gpio_table);
> platform_device_register(&spitz_led_device);
> }
> #else
>
> --
> 2.42.0
>
>
Which driver consumes these GPIOs? Doesn't it need any conversion?
Bart
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors
2023-10-11 14:21 ` Bartosz Golaszewski
@ 2023-10-11 15:17 ` Duje Mihanović
2023-10-11 15:40 ` Bartosz Golaszewski
0 siblings, 1 reply; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 15:17 UTC (permalink / raw)
To: Bartosz Golaszewski
Cc: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij, Andy Shevchenko,
Dmitry Torokhov, Mark Brown, linux-arm-kernel, linux-kernel,
linux-usb, linux-gpio, linux-input, linux-spi
On Wednesday, October 11, 2023 4:21:39 PM CEST Bartosz Golaszewski wrote:
> Which driver consumes these GPIOs? Doesn't it need any conversion?
That is drivers/leds/leds-gpio.c which has already been converted to the
descriptor API way back in 5c51277a9aba ("leds: leds-gpio: Add support for
GPIO descriptors").
Regards,
Duje
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread* Re: [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors
2023-10-11 15:17 ` Duje Mihanović
@ 2023-10-11 15:40 ` Bartosz Golaszewski
0 siblings, 0 replies; 10+ messages in thread
From: Bartosz Golaszewski @ 2023-10-11 15:40 UTC (permalink / raw)
To: Duje Mihanović
Cc: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij, Andy Shevchenko,
Dmitry Torokhov, Mark Brown, linux-arm-kernel, linux-kernel,
linux-usb, linux-gpio, linux-input, linux-spi
On Wed, Oct 11, 2023 at 5:17 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> On Wednesday, October 11, 2023 4:21:39 PM CEST Bartosz Golaszewski wrote:
> > Which driver consumes these GPIOs? Doesn't it need any conversion?
>
> That is drivers/leds/leds-gpio.c which has already been converted to the
> descriptor API way back in 5c51277a9aba ("leds: leds-gpio: Add support for
> GPIO descriptors").
>
> Regards,
> Duje
>
>
>
Perfect. In that case:
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH RFT v8 3/6] ARM: pxa: Convert Spitz CF power control to GPIO descriptors
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 2/6] ARM: pxa: Convert Spitz LEDs " Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 4/6] ARM: pxa: Convert reset driver " Duje Mihanović
` (2 subsequent siblings)
5 siblings, 0 replies; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović, Bartosz Golaszewski
Sharp's Spitz board still uses the legacy GPIO interface for controlling
the power supply to its CF and SD card slots.
Convert it to use the GPIO descriptor interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/spitz.c | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 9efd603c715a..b72c2916426a 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -133,6 +133,10 @@ static unsigned long spitz_pin_config[] __initdata = {
* Scoop GPIO expander
******************************************************************************/
#if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_card_pwr_ctrl_gpio_table, "pxa2xx-mci.0",
+ "sharp-scoop", SPITZ_GPIO_CF_POWER, "cf_power",
+ GPIO_ACTIVE_HIGH);
+
/* SCOOP Device #1 */
static struct resource spitz_scoop_1_resources[] = {
[0] = {
@@ -190,6 +194,7 @@ struct platform_device spitz_scoop_2_device = {
static void __init spitz_scoop_init(void)
{
platform_device_register(&spitz_scoop_1_device);
+ gpiod_add_lookup_table(&spitz_card_pwr_ctrl_gpio_table);
/* Akita doesn't have the second SCOOP chip */
if (!machine_is_akita())
@@ -201,9 +206,18 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
{
unsigned short cpr;
unsigned long flags;
+ struct gpio_desc *cf_power;
+
+ cf_power = gpiod_get(&pxa_device_mci.dev, "cf_power", GPIOD_ASIS);
+ if (IS_ERR(cf_power)) {
+ dev_err(&pxa_device_mci.dev,
+ "failed to get power control GPIO with %ld\n",
+ PTR_ERR(cf_power));
+ return;
+ }
if (new_cpr & 0x7) {
- gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
+ gpiod_direction_output(cf_power, 1);
mdelay(5);
}
@@ -222,8 +236,10 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
if (!(cpr & 0x7)) {
mdelay(1);
- gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
+ gpiod_direction_output(cf_power, 0);
}
+
+ gpiod_put(cf_power);
}
#else
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH RFT v8 4/6] ARM: pxa: Convert reset driver to GPIO descriptors
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
` (2 preceding siblings ...)
2023-10-11 13:23 ` [PATCH RFT v8 3/6] ARM: pxa: Convert Spitz CF power control " Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 5/6] ARM: pxa: Convert gumstix Bluetooth " Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 6/6] input: ads7846: Move wait_for_sync() logic to driver Duje Mihanović
5 siblings, 0 replies; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović, Bartosz Golaszewski
The PXA reset driver still uses the legacy GPIO interface for
configuring and asserting the reset pin.
Convert it to use the GPIO descriptor interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/reset.c | 39 +++++++++++++--------------------------
arch/arm/mach-pxa/reset.h | 3 +--
arch/arm/mach-pxa/spitz.c | 6 +++++-
3 files changed, 19 insertions(+), 29 deletions(-)
diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c
index 27293549f8ad..08bc104b9411 100644
--- a/arch/arm/mach-pxa/reset.c
+++ b/arch/arm/mach-pxa/reset.c
@@ -2,7 +2,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/io.h>
#include <asm/proc-fns.h>
#include <asm/system_misc.h>
@@ -14,33 +14,20 @@
static void do_hw_reset(void);
-static int reset_gpio = -1;
+static struct gpio_desc *reset_gpio;
-int init_gpio_reset(int gpio, int output, int level)
+int init_gpio_reset(int output, int level)
{
- int rc;
-
- rc = gpio_request(gpio, "reset generator");
- if (rc) {
- printk(KERN_ERR "Can't request reset_gpio\n");
- goto out;
+ reset_gpio = gpiod_get(NULL, "reset", GPIOD_ASIS);
+ if (IS_ERR(reset_gpio)) {
+ pr_err("Can't request reset_gpio: %pe\n", reset_gpio);
+ return PTR_ERR(reset_gpio);
}
if (output)
- rc = gpio_direction_output(gpio, level);
+ return gpiod_direction_output(reset_gpio, level);
else
- rc = gpio_direction_input(gpio);
- if (rc) {
- printk(KERN_ERR "Can't configure reset_gpio\n");
- gpio_free(gpio);
- goto out;
- }
-
-out:
- if (!rc)
- reset_gpio = gpio;
-
- return rc;
+ return gpiod_direction_input(reset_gpio);
}
/*
@@ -50,16 +37,16 @@ int init_gpio_reset(int gpio, int output, int level)
*/
static void do_gpio_reset(void)
{
- BUG_ON(reset_gpio == -1);
+ BUG_ON(IS_ERR(reset_gpio));
/* drive it low */
- gpio_direction_output(reset_gpio, 0);
+ gpiod_direction_output(reset_gpio, 0);
mdelay(2);
/* rising edge or drive high */
- gpio_set_value(reset_gpio, 1);
+ gpiod_set_value(reset_gpio, 1);
mdelay(2);
/* falling edge */
- gpio_set_value(reset_gpio, 0);
+ gpiod_set_value(reset_gpio, 0);
/* give it some time */
mdelay(10);
diff --git a/arch/arm/mach-pxa/reset.h b/arch/arm/mach-pxa/reset.h
index 963dd190bc13..5864f61a0e94 100644
--- a/arch/arm/mach-pxa/reset.h
+++ b/arch/arm/mach-pxa/reset.h
@@ -13,10 +13,9 @@ extern void pxa_register_wdt(unsigned int reset_status);
/**
* init_gpio_reset() - register GPIO as reset generator
- * @gpio: gpio nr
* @output: set gpio as output instead of input during normal work
* @level: output level
*/
-extern int init_gpio_reset(int gpio, int output, int level);
+extern int init_gpio_reset(int output, int level);
#endif /* __ASM_ARCH_RESET_H */
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index b72c2916426a..acb2b5495dbe 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -1020,9 +1020,13 @@ static void spitz_restart(enum reboot_mode mode, const char *cmd)
spitz_poweroff();
}
+GPIO_LOOKUP_SINGLE(spitz_reset_gpio_table, NULL, "pxa-gpio",
+ SPITZ_GPIO_ON_RESET, "reset", GPIO_ACTIVE_HIGH);
+
static void __init spitz_init(void)
{
- init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
+ gpiod_add_lookup_table(&spitz_reset_gpio_table);
+ init_gpio_reset(1, 0);
pm_power_off = spitz_poweroff;
PMCR = 0x00;
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH RFT v8 5/6] ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
` (3 preceding siblings ...)
2023-10-11 13:23 ` [PATCH RFT v8 4/6] ARM: pxa: Convert reset driver " Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
2023-10-11 13:23 ` [PATCH RFT v8 6/6] input: ads7846: Move wait_for_sync() logic to driver Duje Mihanović
5 siblings, 0 replies; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović, Bartosz Golaszewski
Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
device.
Convert it to use the GPIO descriptor interface.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/gumstix.c | 22 +++++++++++-----------
1 file changed, 11 insertions(+), 11 deletions(-)
diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c9f0f62187bd..0bca6e2c80a9 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,8 @@
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/gpio/consumer.h>
#include <linux/gpio/machine.h>
-#include <linux/gpio.h>
#include <linux/err.h>
#include <linux/clk.h>
@@ -129,6 +129,11 @@ static void gumstix_udc_init(void)
#endif
#ifdef CONFIG_BT
+GPIO_LOOKUP_SINGLE(gumstix_bt_gpio_table, "pxa2xx-uart.1", "pxa-gpio",
+ GPIO_GUMSTIX_BTRESET, "BTRST", GPIO_ACTIVE_LOW);
+
+static struct gpio_desc *bt_reset;
+
/* Normally, the bootloader would have enabled this 32kHz clock but many
** boards still have u-boot 1.1.4 so we check if it has been turned on and
** if not, we turn it on with a warning message. */
@@ -153,24 +158,19 @@ static void gumstix_setup_bt_clock(void)
static void __init gumstix_bluetooth_init(void)
{
- int err;
+ gpiod_add_lookup_table(&gumstix_bt_gpio_table);
gumstix_setup_bt_clock();
- err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
- if (err) {
+ bt_reset = gpiod_get(&pxa_device_btuart.dev, "BTRST", GPIOD_OUT_HIGH);
+ if (IS_ERR(bt_reset)) {
pr_err("gumstix: failed request gpio for bluetooth reset\n");
return;
}
- err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
- if (err) {
- pr_err("gumstix: can't reset bluetooth\n");
- return;
- }
- gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+ gpiod_set_value(bt_reset, 1);
udelay(100);
- gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+ gpiod_set_value(bt_reset, 0);
}
#else
static void gumstix_bluetooth_init(void)
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH RFT v8 6/6] input: ads7846: Move wait_for_sync() logic to driver
2023-10-11 13:23 [PATCH RFT v8 0/6] ARM: pxa: GPIO descriptor conversions Duje Mihanović
` (4 preceding siblings ...)
2023-10-11 13:23 ` [PATCH RFT v8 5/6] ARM: pxa: Convert gumstix Bluetooth " Duje Mihanović
@ 2023-10-11 13:23 ` Duje Mihanović
5 siblings, 0 replies; 10+ messages in thread
From: Duje Mihanović @ 2023-10-11 13:23 UTC (permalink / raw)
To: Daniel Mack, Haojian Zhuang, Robert Jarzmik, Russell King,
Alan Stern, Greg Kroah-Hartman, Linus Walleij,
Bartosz Golaszewski, Andy Shevchenko, Dmitry Torokhov, Mark Brown
Cc: linux-arm-kernel, linux-kernel, linux-usb, linux-gpio,
linux-input, linux-spi, Duje Mihanović, Bartosz Golaszewski
If this code is left in the board file, the sync GPIO would have to be
separated into another lookup table during conversion to the GPIO
descriptor API (which is also done in this patch).
The only user of this code (Sharp Spitz) is also converted in this
patch.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
arch/arm/mach-pxa/spitz.c | 12 ++----------
drivers/input/touchscreen/ads7846.c | 22 +++++++++++++++-------
include/linux/spi/ads7846.h | 1 -
3 files changed, 17 insertions(+), 18 deletions(-)
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index acb2b5495dbe..e086a13950d2 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -516,22 +516,12 @@ static inline void spitz_leds_init(void) {}
* SSP Devices
******************************************************************************/
#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static void spitz_ads7846_wait_for_hsync(void)
-{
- while (gpio_get_value(SPITZ_GPIO_HSYNC))
- cpu_relax();
-
- while (!gpio_get_value(SPITZ_GPIO_HSYNC))
- cpu_relax();
-}
-
static struct ads7846_platform_data spitz_ads7846_info = {
.model = 7846,
.vref_delay_usecs = 100,
.x_plate_ohms = 419,
.y_plate_ohms = 486,
.pressure_max = 1024,
- .wait_for_sync = spitz_ads7846_wait_for_hsync,
};
static struct gpiod_lookup_table spitz_ads7846_gpio_table = {
@@ -539,6 +529,8 @@ static struct gpiod_lookup_table spitz_ads7846_gpio_table = {
.table = {
GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_TP_INT,
"pendown", GPIO_ACTIVE_LOW),
+ GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_HSYNC,
+ "sync", GPIO_ACTIVE_LOW),
{ }
},
};
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
index faea40dd66d0..139b0f3735d0 100644
--- a/drivers/input/touchscreen/ads7846.c
+++ b/drivers/input/touchscreen/ads7846.c
@@ -138,8 +138,7 @@ struct ads7846 {
void *filter_data;
int (*get_pendown_state)(void);
struct gpio_desc *gpio_pendown;
-
- void (*wait_for_sync)(void);
+ struct gpio_desc *sync;
};
enum ads7846_filter {
@@ -636,9 +635,15 @@ static const struct attribute_group ads784x_attr_group = {
};
/*--------------------------------------------------------------------------*/
-
-static void null_wait_for_sync(void)
+static void ads7846_wait_for_sync_gpio(struct ads7846 *ts)
{
+ if (!ts->sync)
+ return;
+ while (!gpiod_get_value(ts->sync))
+ cpu_relax();
+
+ while (gpiod_get_value(ts->sync))
+ cpu_relax();
}
static int ads7846_debounce_filter(void *ads, int data_idx, int *val)
@@ -803,7 +808,7 @@ static void ads7846_read_state(struct ads7846 *ts)
packet->last_cmd_idx = 0;
while (true) {
- ts->wait_for_sync();
+ ads7846_wait_for_sync_gpio(ts);
m = &ts->msg[msg_idx];
error = spi_sync(ts->spi, m);
@@ -1261,8 +1266,6 @@ static int ads7846_probe(struct spi_device *spi)
ts->penirq_recheck_delay_usecs =
pdata->penirq_recheck_delay_usecs;
- ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;
-
snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev));
snprintf(ts->name, sizeof(ts->name), "ADS%d Touchscreen", ts->model);
@@ -1361,6 +1364,11 @@ static int ads7846_probe(struct spi_device *spi)
if (err)
return err;
+ ts->sync = devm_gpiod_get_optional(dev, "sync", GPIOD_IN);
+ if (IS_ERR(ts->sync))
+ return dev_err_probe(dev, PTR_ERR(ts->sync),
+ "Failed to get sync GPIO");
+
err = input_register_device(input_dev);
if (err)
return err;
diff --git a/include/linux/spi/ads7846.h b/include/linux/spi/ads7846.h
index a04c1c34c344..fa7c4f119023 100644
--- a/include/linux/spi/ads7846.h
+++ b/include/linux/spi/ads7846.h
@@ -38,7 +38,6 @@ struct ads7846_platform_data {
int gpio_pendown_debounce; /* platform specific debounce time for
* the gpio_pendown */
int (*get_pendown_state)(void);
- void (*wait_for_sync)(void);
bool wakeup;
unsigned long irq_flags;
};
--
2.42.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 10+ messages in thread