From: matthias.bgg@gmail.com (Matthias Brugger)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v1 0/6] drivers: net: xgene: Fix 1G hot-plug and module support
Date: Fri, 27 May 2016 19:07:04 +0200 [thread overview]
Message-ID: <57487EB8.6040309@gmail.com> (raw)
In-Reply-To: <1464333768-26150-1-git-send-email-isubramanian@apm.com>
On 27/05/16 09:22, Iyappan Subramanian wrote:
> This patchset addresses the following issues,
>
> 1. hot-plug issue on the SGMII 1G interface
> - by adding a driver for MDIO management
> 2. fixes the kernel crash when the driver loaded as an kernel module
> - by fixing hardware cleanups and rearrange kernel API calls
>
> Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
> ---
Without this patches we observed problems on some hardware when the
driver was loaded as modules, as well as the kernel crash when
unloading/loading the module.
I tested this with an older FW and both issues are fixed, so you can add
Tested-by: Matthias Brugger <mbrugger@suse.com>
But I think the way the series is split in different patches is not
correct. Patch 1 on its own won't compile and get fixed in patch 2.
Although I think backward compatibility to older firmware should be part
of the changes which provide support for the new firmware and should not
be a patch apart. Said this, I'm not sure if just squashing patch 1 and
patch 2 is the right to do, as to me it seems as if some other fixes
slipped into the series.
From my point of view, patch 4 and 5 should be squashed, as xge0clk and
sge1clk nodes are useless when the mdio nodes are present.
Regards,
Matthias
>
> Iyappan Subramanian (6):
> drivers: net: xgene: MAC and PHY configuration changes
> drivers: net: xgene: Backward compatibility with older firmware
> drivers: net: phy: Add MDIO driver
> dtb: xgene: Add MDIO node
> dtb: xgene: Remove clock nodes
> drivers: net: xgene: Fix module load/unload crash
>
> arch/arm64/boot/dts/apm/apm-merlin.dts | 10 +
> arch/arm64/boot/dts/apm/apm-mustang.dts | 12 +
> arch/arm64/boot/dts/apm/apm-shadowcat.dtsi | 23 +-
> arch/arm64/boot/dts/apm/apm-storm.dtsi | 38 +-
> drivers/net/ethernet/apm/xgene/Kconfig | 1 +
> drivers/net/ethernet/apm/xgene/xgene_enet_hw.c | 241 ++++++----
> drivers/net/ethernet/apm/xgene/xgene_enet_hw.h | 18 +-
> drivers/net/ethernet/apm/xgene/xgene_enet_main.c | 325 ++++++++-----
> drivers/net/ethernet/apm/xgene/xgene_enet_main.h | 36 +-
> drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c | 191 +++++++-
> drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.h | 8 +
> drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c | 66 ++-
> drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.h | 4 +
> drivers/net/phy/Kconfig | 7 +
> drivers/net/phy/Makefile | 1 +
> drivers/net/phy/mdio-xgene.c | 531 ++++++++++++++++++++++
> drivers/net/phy/mdio-xgene.h | 140 ++++++
> 17 files changed, 1373 insertions(+), 279 deletions(-)
> create mode 100644 drivers/net/phy/mdio-xgene.c
> create mode 100644 drivers/net/phy/mdio-xgene.h
>
prev parent reply other threads:[~2016-05-27 17:07 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-27 7:22 [PATCH v1 0/6] drivers: net: xgene: Fix 1G hot-plug and module support Iyappan Subramanian
2016-05-27 7:22 ` [PATCH v1 1/6] drivers: net: xgene: MAC and PHY configuration changes Iyappan Subramanian
2016-05-27 17:07 ` Matthias Brugger
2016-05-27 7:22 ` [PATCH v1 2/6] drivers: net: xgene: Backward compatibility with older firmware Iyappan Subramanian
2016-05-27 7:22 ` [PATCH v1 3/6] drivers: net: phy: Add MDIO driver Iyappan Subramanian
2016-05-27 7:22 ` [PATCH v1 4/6] dtb: xgene: Add MDIO node Iyappan Subramanian
2016-05-27 7:22 ` [PATCH v1 5/6] dtb: xgene: Remove clock nodes Iyappan Subramanian
2016-05-30 7:34 ` Matthias Brugger
2016-05-31 23:44 ` Iyappan Subramanian
2016-05-27 7:22 ` [PATCH v1 6/6] drivers: net: xgene: Fix module load/unload crash Iyappan Subramanian
2016-05-27 17:07 ` Matthias Brugger [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=57487EB8.6040309@gmail.com \
--to=matthias.bgg@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).