[PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe support for poplar board

[xuwei5@hisilicon.com (Wei Xu)]

Hi Shawn,

On 2018/5/11 3:03, Shawn Guo wrote:
> It adds combophy devices under peripheral controller and enables PCIe
> support for Hi3798CV200 Poplar board.
> 
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Series applied into the hisilicon dt tree.
Thanks!

BR,
Wei

> ---
>  .../boot/dts/hisilicon/hi3798cv200-poplar.dts      | 15 ++++++
>  arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi     | 63 ++++++++++++++++++++++
>  2 files changed, 78 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> index 4d5d644abb12..c4382e1f3c92 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> @@ -61,6 +61,15 @@
>  			default-state = "off";
>  		};
>  	};
> +
> +	reg_pcie: regulator-pcie {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3V3_PCIE0";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio6 7 0>;
> +		enable-active-high;
> +	};
>  };
>  
>  &gmac1 {
> @@ -146,6 +155,12 @@
>  	status = "okay";
>  };
>  
> +&pcie {
> +	reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
> +	vpcie-supply = <&reg_pcie>;
> +	status = "okay";
> +};
> +
>  &sd0 {
>  	bus-width = <4>;
>  	cap-sd-highspeed;
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> index 962bd79139e4..5b73403551e6 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> @@ -8,7 +8,9 @@
>   */
>  
>  #include <dt-bindings/clock/histb-clock.h>
> +#include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/phy/phy.h>
>  #include <dt-bindings/reset/ti-syscon.h>
>  
>  / {
> @@ -106,6 +108,37 @@
>  			#reset-cells = <2>;
>  		};
>  
> +		perictrl: peripheral-controller at 8a20000 {
> +			compatible = "hisilicon,hi3798cv200-perictrl", "syscon",
> +				     "simple-mfd";
> +			reg = <0x8a20000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0x8a20000 0x1000>;
> +
> +			combphy0: phy at 850 {
> +				compatible = "hisilicon,hi3798cv200-combphy";
> +				reg = <0x850 0x8>;
> +				#phy-cells = <1>;
> +				clocks = <&crg HISTB_COMBPHY0_CLK>;
> +				resets = <&crg 0x188 4>;
> +				assigned-clocks = <&crg HISTB_COMBPHY0_CLK>;
> +				assigned-clock-rates = <100000000>;
> +				hisilicon,fixed-mode = <PHY_TYPE_USB3>;
> +			};
> +
> +			combphy1: phy at 858 {
> +				compatible = "hisilicon,hi3798cv200-combphy";
> +				reg = <0x858 0x8>;
> +				#phy-cells = <1>;
> +				clocks = <&crg HISTB_COMBPHY1_CLK>;
> +				resets = <&crg 0x188 12>;
> +				assigned-clocks = <&crg HISTB_COMBPHY1_CLK>;
> +				assigned-clock-rates = <100000000>;
> +				hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>;
> +			};
> +		};
> +
>  		uart0: serial at 8b00000 {
>  			compatible = "arm,pl011", "arm,primecell";
>  			reg = <0x8b00000 0x1000>;
> @@ -419,5 +452,35 @@
>  			clocks = <&sysctrl HISTB_IR_CLK>;
>  			status = "disabled";
>  		};
> +
> +		pcie: pcie at 9860000 {
> +			compatible = "hisilicon,hi3798cv200-pcie";
> +			reg = <0x9860000 0x1000>,
> +			      <0x0 0x2000>,
> +			      <0x2000000 0x01000000>;
> +			reg-names = "control", "rc-dbi", "config";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			device_type = "pci";
> +			bus-range = <0 15>;
> +			num-lanes = <1>;
> +			ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000
> +				  0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>;
> +			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0>;
> +			interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&crg HISTB_PCIE_AUX_CLK>,
> +				 <&crg HISTB_PCIE_PIPE_CLK>,
> +				 <&crg HISTB_PCIE_SYS_CLK>,
> +				 <&crg HISTB_PCIE_BUS_CLK>;
> +			clock-names = "aux", "pipe", "sys", "bus";
> +			resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
> +			reset-names = "soft", "sys", "bus";
> +			phys = <&combphy1 PHY_TYPE_PCIE>;
> +			phy-names = "phy";
> +			status = "disabled";
> +		};
>  	};
>  };
>