Re: [PATCH 3/4] ARM: dts: stm32: enable stmpe811 on stm32429-disco board

[Alexandre Torgue <alexandre.torgue@st.com>]

Hi Dillon

On 5/7/20 11:16 AM, dillon.minfei@gmail.com wrote:
> From: dillon min <dillon.minfei@gmail.com>
> 
> Enable the stmpe811 touch screen on stm32429-disco board.
> 
> Signed-off-by: dillon min <dillon.minfei@gmail.com>
> ---

You have to add version to your patches. When you send updates of your 
patches, it is better to resend the whole series by adding [PATCH v2] 
... instead of [PATCH] (you can do it easily using git format-patch and 
subject-prefix). Then in your cover letter you have to explain changes 
between 2 series versions.

So please resend the whole series by adding V2 prefix, update 
cover-letter explaining changes, and add a title to your cover-letter 
please.

regards
alex



>   arch/arm/boot/dts/stm32f429-disco.dts | 47 +++++++++++++++++++++++++++++++++++
>   1 file changed, 47 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
> index 30c0f67..fad1ec1 100644
> --- a/arch/arm/boot/dts/stm32f429-disco.dts
> +++ b/arch/arm/boot/dts/stm32f429-disco.dts
> @@ -49,6 +49,8 @@
>   #include "stm32f429.dtsi"
>   #include "stm32f429-pinctrl.dtsi"
>   #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/gpio/gpio.h>
>   
>   / {
>   	model = "STMicroelectronics STM32F429i-DISCO board";
> @@ -127,3 +129,48 @@
>   	pinctrl-names = "default";
>   	status = "okay";
>   };
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3_pins>;
> +	clock-frequency = <100000>;
> +	status = "okay";
> +
> +	stmpe811@41 {
> +		compatible = "st,stmpe811";
> +		reg = <0x41>;
> +		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-parent = <&gpioa>;
> +		/* 3.25 MHz ADC clock speed */
> +		st,adc-freq = <1>;
> +		/* 12-bit ADC */
> +		st,mod-12b = <1>;
> +		/* internal ADC reference */
> +		st,ref-sel = <0>;
> +		/* ADC converstion time: 80 clocks */
> +		st,sample-time = <4>;
> +
> +		stmpe_touchscreen {
> +			compatible = "st,stmpe-ts";
> +			/* 8 sample average control */
> +			st,ave-ctrl = <3>;
> +			/* 7 length fractional part in z */
> +			st,fraction-z = <7>;
> +			/*
> +			 * 50 mA typical 80 mA max touchscreen drivers
> +			 * current limit value
> +			 */
> +			st,i-drive = <1>;
> +			/* 1 ms panel driver settling time */
> +			st,settling = <3>;
> +			/* 5 ms touch detect interrupt delay */
> +			st,touch-det-delay = <5>;
> +		};
> +
> +		stmpe_adc {
> +			compatible = "st,stmpe-adc";
> +			/* forbid to use ADC channels 3-0 (touch) */
> +			st,norequest-mask = <0x0F>;
> +		};
> +	};
> +};
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel