Re: [PATCH 6/7] arm64: dts: Add ipq9574 SoC and AL02 board support

[Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>]

On 1/11/2023 3:14 PM, Krzysztof Kozlowski wrote:
> On 10/01/2023 13:13, devi priya wrote:
>> From: POOVENDHAN SELVARAJ <quic_poovendh@quicinc.com>
>>
>> Add initial device tree support for Qualcomm IPQ9574 SoC
>> and AL02 board
>>
>> Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
>> Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
>> Co-developed-by: devi priya <quic_devipriy@quicinc.com>
>> Signed-off-by: devi priya <quic_devipriy@quicinc.com>
>> Signed-off-by: POOVENDHAN SELVARAJ <quic_poovendh@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/Makefile            |   1 +
>>   arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts |  69 ++++
>>   arch/arm64/boot/dts/qcom/ipq9574.dtsi        | 318 +++++++++++++++++++
>>   3 files changed, 388 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>>   create mode 100644 arch/arm64/boot/dts/qcom/ipq9574.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 3e79496292e7..872c62028a0b 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c2.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)	+= ipq9574-al02-c7.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-alcatel-idol347.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-asus-z00l.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-huawei-g7.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> new file mode 100644
>> index 000000000000..ae3c32f3e16a
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-al02-c7.dts
>> @@ -0,0 +1,69 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
> Not dual licensed? Not BSD?
>
>> +/*
>> + * IPQ9574 AL02-C7 board device tree source
>> + *
>> + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "ipq9574.dtsi"
>> +
>> +/ {
>> +	model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C7";
>> +	compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
>> +	interrupt-parent = <&intc>;
Can this be droppeed? since it is already part of DTSI.
>> +
>> +	aliases {
>> +		serial0 = &blsp1_uart2;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = "serial0:115200n8";
>> +	};
>> +};
>> +
>> +&blsp1_uart2 {
>> +	pinctrl-0 = <&uart2_pins>;
>> +	pinctrl-names = "default";
>> +	status = "okay";
>> +};
>> +
>> +&sdhc_1 {
>> +	pinctrl-0 = <&emmc_pins>;
>> +	pinctrl-names = "default";
>> +	status = "okay";
>> +};
>> +
>> +&tlmm {
>> +	emmc_pins: emmc-state {
>> +		emmc-clk-pins {
>> +			pins = "gpio5";
>> +			function = "sdc_clk";
>> +			drive-strength = <8>;
>> +			bias-disable;
>> +		};
>> +		emmc-cmd-pins {
>> +			pins = "gpio4";
>> +			function = "sdc_cmd";
>> +			drive-strength = <8>;
>> +			bias-pull-up;
>> +		};
>> +		emmc-data-pins {
>> +			pins = "gpio0", "gpio1", "gpio2",
>> +			     "gpio3", "gpio6", "gpio7",
>> +			     "gpio8", "gpio9";
>> +			function = "sdc_data";
>> +			drive-strength = <8>;
>> +			bias-pull-up;
>> +		};
>> +		emmc-rclk-pins {
>> +			pins = "gpio10";
>> +			function = "sdc_rclk";
>> +			drive-strength = <8>;
>> +			bias-pull-down;
>> +		};
>> +	};
>> +
>> +};
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> new file mode 100644
>> index 000000000000..188d18688a77
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -0,0 +1,318 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * IPQ9574 SoC device tree source
>> + *
>> + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/clock/qcom,gcc-ipq9574.h>
>> +#include <dt-bindings/reset/qcom,gcc-ipq9574.h>
>> +
>> +/ {
>> +	interrupt-parent = <&intc>;
>> +	#address-cells = <2>;
>> +	#size-cells = <2>;
>> +
>> +	clocks {
>> +		bias_pll_ubi_nc_clk: bias_pll_ubi_nc_clk {
> No undercores in node names.
>
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <353000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		pcie30_phy0_pipe_clk: pcie30_phy0_pipe_clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <250000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		pcie30_phy1_pipe_clk: pcie30_phy1_pipe_clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <250000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		pcie30_phy2_pipe_clk: pcie30_phy2_pipe_clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <250000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		pcie30_phy3_pipe_clk: pcie30_phy3_pipe_clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <250000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		usb3phy_0_cc_pipe_clk: usb3phy_0_cc_pipe_clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <125000000>;
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		sleep_clk: sleep-clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <32000>;
> That's not a property of the SoC, but board. Either entire clock or at
> least frequency to indicate that the board is providing the clock.
>
>> +			#clock-cells = <0>;> +		};
>> +
>> +		xo_board_clk: xo-board-clk {
>> +			compatible = "fixed-clock";
>> +			clock-frequency = <24000000>;
> Ditto.
>
>> +			#clock-cells = <0>;
>> +		};
>> +	};
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		CPU0: cpu@0 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a73";
>> +			reg = <0x0>;
>> +			enable-method = "psci";
>> +			next-level-cache = <&L2_0>;
>> +		};
>> +
>> +		CPU1: cpu@1 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a73";
>> +			reg = <0x1>;
>> +			enable-method = "psci";
>> +			next-level-cache = <&L2_0>;
>> +		};
>> +
>> +		CPU2: cpu@2 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a73";
>> +			reg = <0x2>;
>> +			enable-method = "psci";
>> +			next-level-cache = <&L2_0>;
>> +		};
>> +
>> +		CPU3: cpu@3 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a73";
>> +			reg = <0x3>;
>> +			enable-method = "psci";
>> +			next-level-cache = <&L2_0>;
>> +		};
>> +
>> +		L2_0: l2-cache {
>> +			compatible = "cache";
>> +			cache-level = <2>;
>> +		};
>> +	};
>> +
>> +	memory@40000000 {
>> +		device_type = "memory";
>> +		/* We expect the bootloader to fill in the size */
>> +		reg = <0x0 0x40000000 0x0 0x0>;
>> +	};
>> +
>> +	pmu {
>> +		compatible = "arm,cortex-a73-pmu";
>> +		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> +	};
>> +
>> +	psci {
>> +		compatible = "arm,psci-1.0";
>> +		method = "smc";
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <2>;
>> +		#size-cells = <2>;
>> +		ranges;
>> +
>> +		tz_region: memory@4a600000 {
>> +			reg = <0x0 0x4a600000 0x0 0x400000>;
>> +			no-map;
>> +		};
>> +	};
>> +
>> +	soc: soc@0 {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0 0 0 0xffffffff>;
>> +		compatible = "simple-bus";
>> +
>> +		tlmm: pinctrl@1000000 {
>> +			compatible = "qcom,ipq9574-tlmm";
>> +			reg = <0x01000000 0x300000>;
>> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> +			gpio-controller;
>> +			#gpio-cells = <2>;
>> +			gpio-ranges = <&tlmm 0 0 65>;
>> +			gpio-reserved-ranges = <59 1>;
> Hm, why reserved ranges are in SoC?
>
>> +			interrupt-controller;
>> +			#interrupt-cells = <2>;
>> +
>> +			uart2_pins: uart2-state {
>> +				pins = "gpio34", "gpio35";
>> +				function = "blsp2_uart";
>> +				drive-strength = <8>;
>> +				bias-disable;
>> +			};
>> +		};
>> +
>> +		gcc: clock-controller@1800000 {
>> +			compatible = "qcom,gcc-ipq9574";
>> +			reg = <0x1800000 0x80000>;
Address can be padded to 8-hex-digits. Please take care of this in all 
nodes.
>> +			clocks = <&xo_board_clk>,
>> +				<&sleep_clk>,
>> +				<&bias_pll_ubi_nc_clk>,
>> +				<&pcie30_phy0_pipe_clk>,
>> +				<&pcie30_phy1_pipe_clk>,
>> +				<&pcie30_phy2_pipe_clk>,
>> +				<&pcie30_phy3_pipe_clk>,
>> +				<&usb3phy_0_cc_pipe_clk>;
>> +			clock-names = "xo",
>> +				"sleep_clk",
> Misaligned. Multiple other places probably as well.
>
>> +				"bias_pll_ubi_nc_clk",
>> +				"pcie30_phy0_pipe_clk",
>> +				"pcie30_phy1_pipe_clk",
>> +				"pcie30_phy2_pipe_clk",
>> +				"pcie30_phy3_pipe_clk",
>> +				"usb3phy_0_cc_pipe_clk";
>> +			#clock-cells = <1>;
>> +			#reset-cells = <1>;
>> +		};
>> +
>> +		sdhc_1: sdhci@7804000 {
>> +			compatible = "qcom,sdhci-msm-v5";
>> +			reg = <0x7804000 0x1000>, <0x7805000 0x1000>;
>> +			reg-names = "hc_mem", "cmdq_mem";
>> +
>> +			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
>> +				   <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
> Like here.
>
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +
>> +			clocks = <&xo_board_clk>,
>> +			       <&gcc GCC_SDCC1_AHB_CLK>,
>> +			       <&gcc GCC_SDCC1_APPS_CLK>;
> And here
>
>> +			clock-names = "xo", "iface", "core";
> Does not look like you tested the bindings. Please run `make
> dt_binding_check` (see
> Documentation/devicetree/bindings/writing-schema.rst for instructions).
>
>> +			mmc-ddr-1_8v;
>> +			mmc-hs200-1_8v;
>> +			mmc-hs400-1_8v;
>> +			mmc-hs400-enhanced-strobe;
>> +			max-frequency = <384000000>;
>> +			bus-width = <8>;
>> +			non-removable;
>> +			status = "disabled";
>> +		};
>> +
>> +		blsp1_uart2: serial@78b1000 {
>> +			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
>> +			reg = <0x078b1000 0x200>;
>> +			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
>> +				 <&gcc GCC_BLSP1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			status = "disabled";
>> +		};
>> +
>> +		intc: interrupt-controller@b000000 {
>> +			compatible = "qcom,msm-qgic2";
>> +			reg = <0x0b000000 0x1000>,  /* GICD */
>> +			      <0x0b002000 0x1000>,  /* GICC */
>> +			      <0x0b001000 0x1000>,  /* GICH */
>> +			      <0x0b004000 0x1000>;  /* GICV */
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			interrupt-controller;
>> +			#interrupt-cells = <3>;
>> +			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> +			ranges = <0 0x0b00c000 0x3000>;
>> +
>> +			v2m0: v2m@0 {
>> +				compatible = "arm,gic-v2m-frame";
>> +				reg = <0x0 0xffd>;
>> +				msi-controller;
>> +			};
>> +
>> +			v2m1: v2m@1 {
>> +				compatible = "arm,gic-v2m-frame";
>> +				reg = <0x1000 0xffd>;
>> +				msi-controller;
>> +			};
>> +
>> +			v2m2: v2m@2 {
>> +				compatible = "arm,gic-v2m-frame";
>> +				reg = <0x2000 0xffd>;
>> +				msi-controller;
>> +			};
>> +		};
>> +
>> +		timer@b120000 {
>> +			compatible = "arm,armv7-timer-mem";
>> +			reg = <0xb120000 0x1000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			clock-frequency = <24000000>;
>> +
>> +			frame@b120000 {
>> +				reg = <0xb121000 0x1000>,
>> +				      <0xb122000 0x1000>;
>> +				frame-number = <0>;
>> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
>> +					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>> +			};
>> +
>> +			frame@b123000 {
>> +				reg = <0xb123000 0x1000>;
>> +				frame-number = <1>;
>> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b124000 {
>> +				reg = <0xb124000 0x1000>;
>> +				frame-number = <2>;
>> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b125000 {
>> +				reg = <0xb125000 0x1000>;
>> +				frame-number = <3>;
>> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b126000 {
>> +				reg = <0xb126000 0x1000>;
>> +				frame-number = <4>;
>> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b127000 {
>> +				reg = <0xb127000 0x1000>;
>> +				frame-number = <5>;
>> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +
>> +			frame@b128000 {
>> +				reg = <0xb128000 0x1000>;
>> +				frame-number = <6>;
>> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
>> +				status = "disabled";
>> +			};
>> +		};
>> +	};
>> +
>> +	timer {
>> +		compatible = "arm,armv8-timer";
>> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
>> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
>> +		clock-frequency = <24000000>;
> Is this allowed in recent designs?
>
>> +	};
>> +};
> Best regards,
> Krzysztof
>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel