* [PATCH]NUC900 LCD Controller Driver
@ 2010-01-11 8:05 Wang Qiang
2010-01-28 9:00 ` Qiang Wang
2010-01-30 0:27 ` Andrew Morton
0 siblings, 2 replies; 7+ messages in thread
From: Wang Qiang @ 2010-01-11 8:05 UTC (permalink / raw)
To: linux-arm-kernel
hi, Dear Wan
There is the patch of LCD controller driver for nuc900s.
The Linux LOGO is just fine and the FB-Test application was ok, too.
best regards
wangqiang
Signed-off-by: Wang Qiang <rurality.linux@gmail.com>
Cc:Wang Zongshun <mcuos.com@gmail.com>
---
diff --git a/arch/arm/configs/nuc950_defconfig
b/arch/arm/configs/nuc950_defconfig
index 97300ec..51cc2a2 100644
--- a/arch/arm/configs/nuc950_defconfig
+++ b/arch/arm/configs/nuc950_defconfig
@@ -590,8 +590,40 @@ CONFIG_SSB_POSSIBLE=y
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_NUC900=y
+CONFIG_GPM1040A0_320X240=y
+CONFIG_FB_NUC900_DEBUG=y
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+
#
# Display device support
@@ -603,6 +635,25 @@ CONFIG_SSB_POSSIBLE=y
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+CONFIG_FONT_8x16=y
+# CONFIG_FONT_6x11 is not set
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
CONFIG_USB_SUPPORT=y
diff --git a/arch/arm/mach-w90x900/cpu.h b/arch/arm/mach-w90x900/cpu.h
index 4d58ba1..f8730b6 100644
--- a/arch/arm/mach-w90x900/cpu.h
+++ b/arch/arm/mach-w90x900/cpu.h
@@ -57,3 +57,4 @@ extern struct platform_device nuc900_device_fmi;
extern struct platform_device nuc900_device_kpi;
extern struct platform_device nuc900_device_rtc;
extern struct platform_device nuc900_device_ts;
+extern struct platform_device nuc900_device_lcd;
diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c
index ec711f4..298c7a2 100644
--- a/arch/arm/mach-w90x900/dev.c
+++ b/arch/arm/mach-w90x900/dev.c
@@ -34,6 +34,7 @@
#include <mach/regs-serial.h>
#include <mach/nuc900_spi.h>
#include <mach/map.h>
+#include <mach/fb.h>
#include "cpu.h"
@@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
.resource = nuc900_kpi_resource,
};
+#ifdef CONFIG_FB_NUC900
+
+static struct resource nuc900_lcd_resource[] = {
+ [0] = {
+ .start = W90X900_PA_LCD,
+ .end = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_LCD,
+ .end = IRQ_LCD,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
+
+struct platform_device nuc900_device_lcd = {
+ .name = "nuc900-lcd",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(nuc900_lcd_resource),
+ .resource = nuc900_lcd_resource,
+ .dev = {
+ .dma_mask = &nuc900_device_lcd_dmamask,
+ .coherent_dma_mask = 0xffffffffUL
+ }
+};
+
+void nuc900_fb_set_platdata(struct nuc900fb_mach_info *pd)
+{
+ struct nuc900fb_mach_info *npd;
+
+ npd = kmalloc(sizeof(*npd), GFP_KERNEL);
+ if (npd) {
+ memcpy(npd, pd, sizeof(*npd));
+ nuc900_device_lcd.dev.platform_data = npd;
+ } else {
+ printk(KERN_ERR "no memory for LCD platform data\n");
+ }
+}
+#endif
+
/*Here should be your evb resourse,such as LCD*/
static struct platform_device *nuc900_public_dev[] __initdata = {
diff --git a/arch/arm/mach-w90x900/include/mach/fb.h
b/arch/arm/mach-w90x900/include/mach/fb.h
new file mode 100644
index 0000000..cec5ece
--- /dev/null
+++ b/arch/arm/mach-w90x900/include/mach/fb.h
@@ -0,0 +1,83 @@
+/* linux/include/asm/arch-nuc900/fb.h
+ *
+ * Copyright (c) 2008 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Changelog:
+ *
+ * 2008/08/26 vincen.zswan modify this file for LCD.
+ */
+
+#ifndef __ASM_ARM_FB_H
+#define __ASM_ARM_FB_H
+
+
+
+/* LCD Controller Hardware Desc */
+struct nuc900fb_hw {
+ unsigned int lcd_dccs;
+ unsigned int lcd_device_ctrl;
+ unsigned int lcd_mpulcd_cmd;
+ unsigned int lcd_int_cs;
+ unsigned int lcd_crtc_size;
+ unsigned int lcd_crtc_dend;
+ unsigned int lcd_crtc_hr;
+ unsigned int lcd_crtc_hsync;
+ unsigned int lcd_crtc_vr;
+ unsigned int lcd_va_baddr0;
+ unsigned int lcd_va_baddr1;
+ unsigned int lcd_va_fbctrl;
+ unsigned int lcd_va_scale;
+ unsigned int lcd_va_test;
+ unsigned int lcd_va_win;
+ unsigned int lcd_va_stuff;
+};
+
+/* LCD Display Description */
+struct nuc900fb_display {
+ /* LCD Image type */
+ unsigned type;
+
+ /* LCD Screen Size */
+ unsigned short width;
+ unsigned short height;
+
+ /* LCD Screen Info */
+ unsigned short xres;
+ unsigned short yres;
+ unsigned short bpp;
+
+ unsigned long pixclock;
+ unsigned short left_margin;
+ unsigned short right_margin;
+ unsigned short hsync_len;
+ unsigned short upper_margin;
+ unsigned short lower_margin;
+ unsigned short vsync_len;
+
+ /* hardware special register value */
+ unsigned int dccs;
+ unsigned int devctl;
+ unsigned int fbctrl;
+ unsigned int scale;
+};
+
+struct nuc900fb_mach_info {
+ struct nuc900fb_display *displays;
+ unsigned num_displays;
+ unsigned default_display;
+ /* GPIO Setting Info */
+ unsigned gpio_dir;
+ unsigned gpio_dir_mask;
+ unsigned gpio_data;
+ unsigned gpio_data_mask;
+};
+
+extern void __init nuc900_fb_set_platdata(struct nuc900fb_mach_info *);
+
+#endif /* __ASM_ARM_FB_H */
diff --git a/arch/arm/mach-w90x900/include/mach/regs-ldm.h
b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
new file mode 100644
index 0000000..e9d480a
--- /dev/null
+++ b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
@@ -0,0 +1,253 @@
+/*
+ * arch/arm/mach-w90x900/include/mach/regs-serial.h
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Description:
+ * Nuvoton Display, LCM Register list
+ * Author: Wang Qiang (rurality.linux at gmail.com) 2009/12/11
+ *
+ */
+
+
+#ifndef __ASM_ARM_W90X900_REGS_LDM_H
+#define __ASM_ARM_W90X900_REGS_LDM_H
+
+#include <mach/map.h>
+
+/* Display Controller Control/Status Register */
+#define REG_LCM_DCCS (0x00)
+
+#define LCM_DCCS_ENG_RST (1 << 0)
+#define LCM_DCCS_VA_EN (1 << 1)
+#define LCM_DCCS_OSD_EN (1 << 2)
+#define LCM_DCCS_DISP_OUT_EN (1 << 3)
+#define LCM_DCCS_DISP_INT_EN (1 << 4)
+#define LCM_DCCS_CMD_ON (1 << 5)
+#define LCM_DCCS_FIELD_INTR (1 << 6)
+#define LCM_DCCS_SINGLE (1 << 7)
+
+enum LCM_DCCS_VA_SRC {
+ LCM_DCCS_VA_SRC_YUV422 = (0 << 8),
+ LCM_DCCS_VA_SRC_YCBCR422 = (1 << 8),
+ LCM_DCCS_VA_SRC_RGB888 = (2 << 8),
+ LCM_DCCS_VA_SRC_RGB666 = (3 << 8),
+ LCM_DCCS_VA_SRC_RGB565 = (4 << 8),
+ LCM_DCCS_VA_SRC_RGB444LOW = (5 << 8),
+ LCM_DCCS_VA_SRC_RGB444HIGH = (7 << 8)
+};
+
+
+/* Display Device Control Register */
+#define REG_LCM_DEV_CTRL (0x04)
+
+enum LCM_DEV_CTRL_SWAP_YCbCr {
+ LCM_DEV_CTRL_SWAP_UYVY = (0 << 1),
+ LCM_DEV_CTRL_SWAP_YUYV = (1 << 1),
+ LCM_DEV_CTRL_SWAP_VYUY = (2 << 1),
+ LCM_DEV_CTRL_SWAP_YVYU = (3 << 1)
+};
+
+enum LCM_DEV_CTRL_RGB_SHIFT {
+ LCM_DEV_CTRL_RGB_SHIFT_NOT = (0 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_ONECYCLE = (1 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_TWOCYCLE = (2 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_NOT_DEF = (3 << 3)
+};
+
+enum LCM_DEV_CTRL_DEVICE {
+ LCM_DEV_CTRL_DEVICE_YUV422 = (0 << 5),
+ LCM_DEV_CTRL_DEVICE_YUV444 = (1 << 5),
+ LCM_DEV_CTRL_DEVICE_UNIPAC = (4 << 5),
+ LCM_DEV_CTRL_DEVICE_SEIKO_EPSON = (5 << 5),
+ LCM_DEV_CTRL_DEVICE_HIGH_COLOR = (6 << 5),
+ LCM_DEV_CTRL_DEVICE_MPU = (7 << 5)
+};
+
+#define LCM_DEV_CTRL_LCD_DDA (8)
+#define LCM_DEV_CTRL_YUV2CCIR (16)
+
+enum LCM_DEV_CTRL_LCD_SEL {
+ LCM_DEV_CTRL_LCD_SEL_RGB_GBR = (0 << 17),
+ LCM_DEV_CTRL_LCD_SEL_BGR_RBG = (1 << 17),
+ LCM_DEV_CTRL_LCD_SEL_GBR_RGB = (2 << 17),
+ LCM_DEV_CTRL_LCD_SEL_RBG_BGR = (3 << 17)
+};
+
+enum LCM_DEV_CTRL_FAL_D {
+ LCM_DEV_CTRL_FAL_D_FALLING = (0 << 19),
+ LCM_DEV_CTRL_FAL_D_RISING = (1 << 19),
+};
+
+enum LCM_DEV_CTRL_H_POL {
+ LCM_DEV_CTRL_H_POL_LOW = (0 << 20),
+ LCM_DEV_CTRL_H_POL_HIGH = (1 << 20),
+};
+
+enum LCM_DEV_CTRL_V_POL {
+ LCM_DEV_CTRL_V_POL_LOW = (0 << 21),
+ LCM_DEV_CTRL_V_POL_HIGH = (1 << 21),
+};
+
+enum LCM_DEV_CTRL_VR_LACE {
+ LCM_DEV_CTRL_VR_LACE_NINTERLACE = (0 << 22),
+ LCM_DEV_CTRL_VR_LACE_INTERLACE = (1 << 22),
+};
+
+enum LCM_DEV_CTRL_LACE {
+ LCM_DEV_CTRL_LACE_NINTERLACE = (0 << 23),
+ LCM_DEV_CTRL_LACE_INTERLACE = (1 << 23),
+};
+
+enum LCM_DEV_CTRL_RGB_SCALE {
+ LCM_DEV_CTRL_RGB_SCALE_4096 = (0 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_65536 = (1 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_262144 = (2 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_16777216 = (3 << 24),
+};
+
+enum LCM_DEV_CTRL_DBWORD {
+ LCM_DEV_CTRL_DBWORD_HALFWORD = (0 << 26),
+ LCM_DEV_CTRL_DBWORD_FULLWORD = (1 << 26),
+};
+
+enum LCM_DEV_CTRL_MPU68 {
+ LCM_DEV_CTRL_MPU68_80_SERIES = (0 << 27),
+ LCM_DEV_CTRL_MPU68_68_SERIES = (1 << 27),
+};
+
+enum LCM_DEV_CTRL_DE_POL {
+ LCM_DEV_CTRL_DE_POL_HIGH = (0 << 28),
+ LCM_DEV_CTRL_DE_POL_LOW = (1 << 28),
+};
+
+#define LCM_DEV_CTRL_CMD16 (29)
+#define LCM_DEV_CTRL_CM16t18 (30)
+#define LCM_DEV_CTRL_CMD_LOW (31)
+
+/* MPU-Interface LCD Write Command */
+#define REG_LCM_MPU_CMD (0x08)
+
+/* Interrupt Control/Status Register */
+#define REG_LCM_INT_CS (0x0c)
+#define LCM_INT_CS_DISP_F_EN (1 << 0)
+#define LCM_INT_CS_UNDERRUN_EN (1 << 1)
+#define LCM_INT_CS_BUS_ERROR_INT (1 << 28)
+#define LCM_INT_CS_UNDERRUN_INT (1 << 29)
+#define LCM_INT_CS_DISP_F_STATUS (1 << 30)
+#define LCM_INT_CS_DISP_F_INT (1 << 31)
+
+/* CRTC Display Size Control Register */
+#define REG_LCM_CRTC_SIZE (0x10)
+#define LCM_CRTC_SIZE_VTTVAL(x) ((x) << 16)
+#define LCM_CRTC_SIZE_HTTVAL(x) ((x) << 0)
+
+/* CRTC Display Enable End */
+#define REG_LCM_CRTC_DEND (0x14)
+#define LCM_CRTC_DEND_VDENDVAL(x) ((x) << 16)
+#define LCM_CRTC_DEND_HDENDVAL(x) ((x) << 0)
+
+/* CRTC Internal Horizontal Retrace Control Register */
+#define REG_LCM_CRTC_HR (0x18)
+#define LCM_CRTC_HR_EVAL(x) ((x) << 16)
+#define LCM_CRTC_HR_SVAL(x) ((x) << 0)
+
+/* CRTC Horizontal Sync Control Register */
+#define REG_LCM_CRTC_HSYNC (0x1C)
+#define LCM_CRTC_HSYNC_SHIFTVAL(x) ((x) << 30)
+#define LCM_CRTC_HSYNC_EVAL(x) ((x) << 16)
+#define LCM_CRTC_HSYNC_SVAL(x) ((x) << 0)
+
+/* CRTC Internal Vertical Retrace Control Register */
+#define REG_LCM_CRTC_VR (0x20)
+#define LCM_CRTC_VR_EVAL(x) ((x) << 16)
+#define LCM_CRTC_VR_SVAL(x) ((x) << 0)
+
+/* Video Stream Frame Buffer-0 Starting Address */
+#define REG_LCM_VA_BADDR0 (0x24)
+
+/* Video Stream Frame Buffer-1 Starting Address */
+#define REG_LCM_VA_BADDR1 (0x28)
+
+/* Video Stream Frame Buffer Control Register */
+#define REG_LCM_VA_FBCTRL (0x2C)
+#define LCM_VA_FBCTRL_IO_REGION_HALF (1 << 28)
+#define LCM_VA_FBCTRL_FIELD_DUAL (1 << 29)
+#define LCM_VA_FBCTRL_START_BUF (1 << 30)
+#define LCM_VA_FBCTRL_DB_EN (1 << 31)
+
+/* Video Stream Scaling Control Register */
+#define REG_LCM_VA_SCALE (0x30)
+#define LCM_VA_SCALE_XCOPY_INTERPOLATION (0 << 15)
+#define LCM_VA_SCALE_XCOPY_DUPLICATION (1 << 15)
+
+/* Image Stream Active Window Coordinates */
+#define REG_LCM_VA_WIN (0x38)
+
+/* Image Stream Stuff Pixel */
+#define REG_LCM_VA_STUFF (0x3C)
+
+/* OSD Window Starting Coordinates */
+#define REG_LCM_OSD_WINS (0x40)
+
+/* OSD Window Ending Coordinates */
+#define REG_LCM_OSD_WINE (0x44)
+
+/* OSD Stream Frame Buffer Starting Address */
+#define REG_LCM_OSD_BADDR (0x48)
+
+/* OSD Stream Frame Buffer Control Register */
+#define REG_LCM_OSD_FBCTRL (0x4c)
+
+/* OSD Overlay Control Register */
+#define REG_LCM_OSD_OVERLAY (0x50)
+
+/* OSD Overlay Color-Key Pattern Register */
+#define REG_LCM_OSD_CKEY (0x54)
+
+/* OSD Overlay Color-Key Mask Register */
+#define REG_LCM_OSD_CMASK (0x58)
+
+/* OSD Window Skip1 Register */
+#define REG_LCM_OSD_SKIP1 (0x5C)
+
+/* OSD Window Skip2 Register */
+#define REG_LCM_OSD_SKIP2 (0x60)
+
+/* OSD horizontal up scaling control register */
+#define REG_LCM_OSD_SCALE (0x64)
+
+/* MPU Vsync control register */
+#define REG_LCM_MPU_VSYNC (0x68)
+
+/* Hardware cursor control Register */
+#define REG_LCM_HC_CTRL (0x6C)
+
+/* Hardware cursot tip point potison on va picture */
+#define REG_LCM_HC_POS (0x70)
+
+/* Hardware Cursor Window Buffer Control Register */
+#define REG_LCM_HC_WBCTRL (0x74)
+
+/* Hardware cursor memory base address register */
+#define REG_LCM_HC_BADDR (0x78)
+
+/* Hardware cursor color ram register mapped to bpp = 0 */
+#define REG_LCM_HC_COLOR0 (0x7C)
+
+/* Hardware cursor color ram register mapped to bpp = 1 */
+#define REG_LCM_HC_COLOR1 (0x80)
+
+/* Hardware cursor color ram register mapped to bpp = 2 */
+#define REG_LCM_HC_COLOR2 (0x84)
+
+/* Hardware cursor color ram register mapped to bpp = 3 */
+#define REG_LCM_HC_COLOR3 (0x88)
+
+#endif /* __ASM_ARM_W90X900_REGS_LDM_H */
diff --git a/arch/arm/mach-w90x900/mach-nuc950evb.c
b/arch/arm/mach-w90x900/mach-nuc950evb.c
index cef903b..b3edc3c 100644
--- a/arch/arm/mach-w90x900/mach-nuc950evb.c
+++ b/arch/arm/mach-w90x900/mach-nuc950evb.c
@@ -10,6 +10,8 @@
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation;version 2 of the License.
+ * history:
+ * Wang Qiang (rurality.linux@gmail.com) add LCD support
*
*/
@@ -18,9 +20,51 @@
#include <asm/mach/map.h>
#include <asm/mach-types.h>
#include <mach/map.h>
+#include <mach/regs-ldm.h>
+#include <mach/fb.h>
#include "nuc950.h"
+#ifdef CONFIG_FB_NUC900
+/* LCD Controller */
+static struct nuc900fb_display __initdata nuc950_lcd_info[] = {
+ /* Giantplus Technology GPM1040A0 320x240 Color TFT LCD */
+ [0] = {
+ .type = LCM_DCCS_VA_SRC_RGB565,
+ .width = 320,
+ .height = 240,
+ .xres = 320,
+ .yres = 240,
+ .bpp = 16,
+ .pixclock = 200000,
+ .left_margin = 34,
+ .right_margin = 54,
+ .hsync_len = 10,
+ .upper_margin = 18,
+ .lower_margin = 4,
+ .vsync_len = 1,
+ .dccs = 0x8e00041a,
+ .devctl = 0x060800c0,
+ .fbctrl = 0x00a000a0,
+ .scale = 0x04000400,
+ },
+};
+
+static struct nuc900fb_mach_info nuc950_fb_info __initdata = {
+#if defined(CONFIG_GPM1040A0_320X240)
+ .displays = &nuc950_lcd_info[0],
+#else
+ .displays = nuc950_lcd_info,
+#endif
+ .num_displays = ARRAY_SIZE(nuc950_lcd_info),
+ .default_display = 0,
+ .gpio_dir = 0x00000004,
+ .gpio_dir_mask = 0xFFFFFFFD,
+ .gpio_data = 0x00000004,
+ .gpio_data_mask = 0xFFFFFFFD,
+};
+#endif
+
static void __init nuc950evb_map_io(void)
{
nuc950_map_io();
@@ -30,6 +74,9 @@ static void __init nuc950evb_map_io(void)
static void __init nuc950evb_init(void)
{
nuc950_board_init();
+#ifdef CONFIG_FB_NUC900
+ nuc900_fb_set_platdata(&nuc950_fb_info);
+#endif
}
MACHINE_START(W90P950EVB, "W90P950EVB")
diff --git a/arch/arm/mach-w90x900/nuc950.c b/arch/arm/mach-w90x900/nuc950.c
index 1495081..4d1f1ab 100644
--- a/arch/arm/mach-w90x900/nuc950.c
+++ b/arch/arm/mach-w90x900/nuc950.c
@@ -18,6 +18,7 @@
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <mach/hardware.h>
+
#include "cpu.h"
/* define specific CPU platform device */
@@ -25,6 +26,9 @@
static struct platform_device *nuc950_dev[] __initdata = {
&nuc900_device_kpi,
&nuc900_device_fmi,
+#ifdef CONFIG_FB_NUC900
+ &nuc900_device_lcd,
+#endif
};
/* define specific CPU platform io map */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 5a5c303..a943e5e 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1945,6 +1945,27 @@ config FB_S3C2410_DEBUG
Turn on debugging messages. Note that you can set/unset at run time
through sysfs
+config FB_NUC900
+ bool "NUC900 LCD framebuffer support"
+ depends on FB && ARCH_W90X900
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ ---help---
+ Frame buffer driver for the built-in LCD controller in the Nuvoton
+ NUC900 processor
+
+config GPM1040A0_320X240
+ bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
+ depends on FB_NUC900
+
+config FB_NUC900_DEBUG
+ bool "NUC900 lcd debug messages"
+ depends on FB_NUC900
+ help
+ Turn on debugging messages. Note that you can set/unset at run time
+ through sysfs
+
config FB_SM501
tristate "Silicon Motion SM501 framebuffer support"
depends on FB && MFD_SM501
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 4ecb30c..a42ad55 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -129,6 +129,7 @@ obj-$(CONFIG_XEN_FBDEV_FRONTEND) += xen-fbfront.o
obj-$(CONFIG_FB_CARMINE) += carminefb.o
obj-$(CONFIG_FB_MB862XX) += mb862xx/
obj-$(CONFIG_FB_MSM) += msm/
+obj-$(CONFIG_FB_NUC900) += nuc900fb.o
# Platform or fallback drivers go here
obj-$(CONFIG_FB_UVESA) += uvesafb.o
diff --git a/drivers/video/nuc900fb.c b/drivers/video/nuc900fb.c
new file mode 100644
index 0000000..c4ff225
--- /dev/null
+++ b/drivers/video/nuc900fb.c
@@ -0,0 +1,842 @@
+/*
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Description:
+ * Nuvoton LCD Controller Driver
+ * Author:
+ * Wang Qiang (rurality.linux at gmail.com) 2009/12/11
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/tty.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/workqueue.h>
+#include <linux/wait.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/cpufreq.h>
+#include <linux/io.h>
+
+#ifdef CONFIG_PM
+#include <linux/pm.h>
+#endif
+
+#include <mach/map.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-ldm.h>
+#include <mach/fb.h>
+#include <mach/clkdev.h>
+
+#include "nuc900fb.h"
+
+/* Debugging stuff */
+#ifdef CONFIG_FB_NUC900_DEBUG
+static int debug = 1;
+#define dprintk(msg...) { printk(KERN_DEBUG "nuc900 lcd: " msg); }
+#else
+static int debug;
+#define dprintk(msg...)
+#endif
+
+
+/*
+ * Initialize the nuc900 video (dual) buffer address
+ */
+static void nuc900fb_set_lcdaddr(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+ unsigned long vbaddr1, vbaddr2;
+ vbaddr1 = info->fix.smem_start;
+ vbaddr2 = info->fix.smem_start;
+ vbaddr2 += info->fix.line_length * info->var.yres;
+ /*set frambuffer start phy addr*/
+ writel(vbaddr1, regs + REG_LCM_VA_BADDR0);
+ writel(vbaddr2, regs + REG_LCM_VA_BADDR1);
+
+ writel(fbi->regs.lcd_va_fbctrl, regs + REG_LCM_VA_FBCTRL);
+ writel(fbi->regs.lcd_va_scale, regs + REG_LCM_VA_SCALE);
+}
+
+//static void nuc900fb_clk_select(struct fb_info *info, unsigned long pixclk)
+//{
+// struct nuc900fb_info *fbi = info->par;
+// int div;
+// if (clk <= 15 * 1000 * 1000) {
+// div = (15 * 1000 * 1000)/
+// nuc900_driver_clksrc_div(fbi->dev, "ext", 0x2);
+// }
+//
+//}
+
+/*
+ * calculate divider for lcd div
+ */
+static unsigned int nuc900fb_calc_pixclk(struct nuc900fb_info *fbi,
+ unsigned long pixclk)
+{
+ unsigned long clk = fbi->clk_rate;
+ unsigned long long div;
+
+ /* pixclk is in picseconds. our clock is in Hz*/
+ /* div = (clk * pixclk)/10^12 */
+ div = (unsigned long long)clk * pixclk;
+ div >>= 12;
+ do_div(div, 625 * 625UL * 625);
+
+ dprintk("pixclk %ld, divisor is %ld\n", pixclk, (long)div);
+
+ return div;
+}
+
+/*
+ * Check the video params of 'var'.
+ */
+static int nuc900fb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
+ struct nuc900fb_display *display = NULL;
+ struct nuc900fb_display *default_display = mach_info->displays +
+ mach_info->default_display;
+ int i;
+
+ dprintk("check_var(var=%p, info=%p)\n", var, info);
+
+ /* validate x/y resolution */
+ /* choose default mode if possible */
+ if (var->xres == default_display->xres &&
+ var->yres == default_display->yres &&
+ var->bits_per_pixel == default_display->bpp)
+ display = default_display;
+ else
+ for (i = 0; i < mach_info->num_displays; i++)
+ if (var->xres == mach_info->displays[i].xres &&
+ var->yres == mach_info->displays[i].yres &&
+ var->bits_per_pixel == mach_info->displays[i].bpp) {
+ display = mach_info->displays + i;
+ break;
+ }
+
+ if (display == NULL) {
+ dprintk("wrong resolution or depth %dx%d at %d bit per pixel\n",
+ var->xres, var->yres, var->bits_per_pixel);
+ return -EINVAL;
+ }
+
+ /* it should be the same size as the display */
+ var->xres_virtual = display->xres;
+ var->yres_virtual = display->yres;
+ var->height = display->height;
+ var->width = display->width;
+
+ /* copy lcd settings */
+ var->pixclock = display->pixclock;
+ var->left_margin = display->left_margin;
+ var->right_margin = display->right_margin;
+ var->upper_margin = display->upper_margin;
+ var->lower_margin = display->lower_margin;
+ var->vsync_len = display->vsync_len;
+ var->hsync_len = display->hsync_len;
+
+ var->transp.offset = 0;
+ var->transp.length = 0;
+
+ fbi->regs.lcd_dccs = display->dccs;
+ fbi->regs.lcd_device_ctrl = display->devctl;
+ fbi->regs.lcd_va_fbctrl = display->fbctrl;
+ fbi->regs.lcd_va_scale = display->scale;
+
+ /* set R/G/B possions */
+ switch (var->bits_per_pixel) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ default:
+ var->red.offset = 0;
+ var->red.length = var->bits_per_pixel;
+ var->green = var->red;
+ var->blue = var->red;
+ break;
+ case 12:
+ var->red.length = 4;
+ var->green.length = 4;
+ var->blue.length = 4;
+ var->red.offset = 8;
+ var->green.offset = 4;
+ var->blue.offset = 0;
+ break;
+ case 16:
+ var->red.length = 5;
+ var->green.length = 6;
+ var->blue.length = 5;
+ var->red.offset = 11;
+ var->green.offset = 5;
+ var->blue.offset = 0;
+ break;
+ case 18:
+ var->red.length = 6;
+ var->green.length = 6;
+ var->blue.length = 6;
+ var->red.offset = 12;
+ var->green.offset = 6;
+ var->blue.offset = 0;
+ break;
+ case 32:
+ var->red.length = 8;
+ var->green.length = 8;
+ var->blue.length = 8;
+ var->red.offset = 16;
+ var->green.offset = 8;
+ var->blue.offset = 0;
+ break;
+ }
+
+ return 0;
+}
+
+/*
+ * Calculate lcd register values from var setting & save into hw
+ */
+static void nuc900fb_calculate_lcd_regs(const struct fb_info *info,
+ struct nuc900fb_hw *regs)
+{
+ const struct fb_var_screeninfo *var = &info->var;
+ int vtt = var->height + var->upper_margin + var->lower_margin;
+ int htt = var->width + var->left_margin + var->right_margin;
+ int hsync = var->width + var->right_margin;
+ int vsync = var->height + var->lower_margin;
+ regs->lcd_crtc_size = LCM_CRTC_SIZE_VTTVAL(vtt) |
+ LCM_CRTC_SIZE_HTTVAL(htt);
+ regs->lcd_crtc_dend = LCM_CRTC_DEND_VDENDVAL(var->height) |
+ LCM_CRTC_DEND_HDENDVAL(var->width);
+ regs->lcd_crtc_hr = LCM_CRTC_HR_EVAL(var->width + 5) |
+ LCM_CRTC_HR_SVAL(var->width + 1);
+ regs->lcd_crtc_hsync = LCM_CRTC_HSYNC_EVAL(hsync + var->hsync_len) |
+ LCM_CRTC_HSYNC_SVAL(hsync);
+ regs->lcd_crtc_vr = LCM_CRTC_VR_EVAL(vsync + var->vsync_len) |
+ LCM_CRTC_VR_SVAL(vsync);
+
+}
+
+/*
+ * Activate (set) the controller from the given framebuffer
+ * information
+ */
+static void nuc900fb_activate_var(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+ struct fb_var_screeninfo *var = &info->var;
+ int clkdiv;
+
+ clkdiv = nuc900fb_calc_pixclk(fbi, var->pixclock) - 1;
+ if (clkdiv < 0)
+ clkdiv = 0;
+
+ nuc900fb_calculate_lcd_regs(info, &fbi->regs);
+
+ /* set the new lcd registers*/
+
+ dprintk("new lcd register set:\n");
+ dprintk("dccs = 0x%08x\n", fbi->regs.lcd_dccs);
+ dprintk("dev_ctl = 0x%08x\n", fbi->regs.lcd_device_ctrl);
+ dprintk("crtc_size = 0x%08x\n", fbi->regs.lcd_crtc_size);
+ dprintk("crtc_dend = 0x%08x\n", fbi->regs.lcd_crtc_dend);
+ dprintk("crtc_hr = 0x%08x\n", fbi->regs.lcd_crtc_hr);
+ dprintk("crtc_hsync = 0x%08x\n", fbi->regs.lcd_crtc_hsync);
+ dprintk("crtc_vr = 0x%08x\n", fbi->regs.lcd_crtc_vr);
+
+ writel(fbi->regs.lcd_device_ctrl, regs + REG_LCM_DEV_CTRL);
+ writel(fbi->regs.lcd_crtc_size, regs + REG_LCM_CRTC_SIZE);
+ writel(fbi->regs.lcd_crtc_dend, regs + REG_LCM_CRTC_DEND);
+ writel(fbi->regs.lcd_crtc_hr, regs + REG_LCM_CRTC_HR);
+ writel(fbi->regs.lcd_crtc_hsync, regs + REG_LCM_CRTC_HSYNC);
+ writel(fbi->regs.lcd_crtc_vr, regs + REG_LCM_CRTC_VR);
+
+ /* set lcd address pointers */
+ nuc900fb_set_lcdaddr(info);
+
+ writel(fbi->regs.lcd_dccs, regs + REG_LCM_DCCS);
+}
+
+/*
+ * Alters the hardware state.
+ *
+ */
+static int nuc900fb_set_par(struct fb_info *info)
+{
+ struct fb_var_screeninfo *var = &info->var;
+
+ dprintk("nuc900fb_set_par\n");
+
+ switch (var->bits_per_pixel) {
+ case 32:
+ case 24:
+ case 18:
+ case 16:
+ case 12:
+ info->fix.visual = FB_VISUAL_TRUECOLOR;
+ break;
+ case 1:
+ info->fix.visual = FB_VISUAL_MONO01;
+ break;
+ default:
+ info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
+ break;
+ }
+
+ info->fix.line_length = (var->xres_virtual * var->bits_per_pixel) / 8;
+
+ /* activate this new configuration */
+ nuc900fb_activate_var(info);
+ return 0;
+}
+
+static inline unsigned int chan_to_field(unsigned int chan,
+ struct fb_bitfield *bf)
+{
+ chan &= 0xffff;
+ chan >>= 16 - bf->length;
+ return chan << bf->offset;
+}
+
+static int nuc900fb_setcolreg(unsigned regno,
+ unsigned red, unsigned green, unsigned blue,
+ unsigned transp, struct fb_info *info)
+{
+ unsigned int val;
+
+ switch (info->fix.visual) {
+ case FB_VISUAL_TRUECOLOR:
+ /* true-colour, use pseuo-palette */
+ if (regno < 16) {
+ u32 *pal = info->pseudo_palette;
+
+ val = chan_to_field(red, &info->var.red);
+ val |= chan_to_field(green, &info->var.green);
+ val |= chan_to_field(blue, &info->var.blue);
+ pal[regno] = val;
+ }
+ break;
+
+ default:
+ return 1; /* unknown type */
+ }
+ return 0;
+}
+
+/**
+ * nuc900fb_blank
+ *
+ */
+static int nuc900fb_blank(int blank_mode, struct fb_info *info)
+{
+
+ return 0;
+}
+
+static int nuc900fb_debug_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return snprintf(buf, PAGE_SIZE, "%s\n", debug ? "on" : "off");
+}
+
+static int nuc900fb_debug_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t len)
+{
+ if (len < 1)
+ return -EINVAL;
+
+ if (strnicmp(buf, "on", 2) == 0 ||
+ strnicmp(buf, "1", 1) == 0) {
+ debug = 1;
+ } else if (strnicmp(buf, "off", 3) == 0 ||
+ strnicmp(buf, "0", 1) == 0) {
+ debug = 0;
+
+ } else {
+ return -EINVAL;
+ }
+
+ return len;
+}
+
+static DEVICE_ATTR(debug, 0666, nuc900fb_debug_show, nuc900fb_debug_store);
+
+static struct fb_ops nuc900fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = nuc900fb_check_var,
+ .fb_set_par = nuc900fb_set_par,
+ .fb_blank = nuc900fb_blank,
+ .fb_setcolreg = nuc900fb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+
+static inline void modify_gpio(void __iomem *reg,
+ unsigned long set, unsigned long mask)
+{
+ unsigned long tmp;
+ tmp = readl(reg) & ~mask;
+ writel(tmp | set, reg);
+}
+
+/*
+ * Initialise LCD-related registers
+ */
+static int nuc900fb_init_registers(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
+ void __iomem *regs = fbi->io;
+
+ /*reset the display engine*/
+ writel(0, regs + REG_LCM_DCCS);
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_ENG_RST,
+ regs + REG_LCM_DCCS);
+ ndelay(100);
+ writel(readl(regs + REG_LCM_DCCS) & (~LCM_DCCS_ENG_RST),
+ regs + REG_LCM_DCCS);
+ ndelay(100);
+
+ writel(0, regs + REG_LCM_DEV_CTRL);
+
+ /* config gpio output */
+ modify_gpio(W90X900_VA_GPIO + 0x54, mach_info->gpio_dir,
+ mach_info->gpio_dir_mask);
+ modify_gpio(W90X900_VA_GPIO + 0x58, mach_info->gpio_data,
+ mach_info->gpio_data_mask);
+
+ return 0;
+}
+
+
+/*
+ * Alloc the SDRAM region of NUC900 for the frame buffer.
+ * The buffer should be a non-cached, non-buffered, memory region
+ * to allow palette and pixel writes without flushing the cache.
+ */
+static int __init nuc900fb_map_video_memory(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ dma_addr_t map_dma;
+ unsigned long map_size = PAGE_ALIGN(info->fix.smem_len);
+
+ dprintk("nuc900fb_map_video_memory(fbi=%p) map_size %lu\n",
+ fbi, map_size);
+
+ info->screen_base = dma_alloc_writecombine(fbi->dev, map_size,
+ &map_dma, GFP_KERNEL);
+
+ if (info->screen_base != NULL) {
+ dprintk("nuc900fb_map_video_memory: clear %p:%08lx\n",
+ info->screen_base, map_size);
+ memset(info->screen_base, 0x00, map_size);
+
+ info->fix.smem_start = map_dma;
+ dprintk("nuc900fb_map_video_memory: "
+ "dma=%08lx cpu=%p size=%08lx\n",
+ info->fix.smem_start, info->screen_base, map_size);
+ }
+ return (info->screen_base) ? 0 : -ENOMEM;
+}
+
+static inline void nuc900fb_unmap_video_memory(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ dma_free_writecombine(fbi->dev, PAGE_ALIGN(info->fix.smem_len),
+ info->screen_base, info->fix.smem_start);
+}
+
+static irqreturn_t nuc900fb_irqhandler(int irq, void *dev_id)
+{
+ struct nuc900fb_info *fbi = dev_id;
+ void __iomem *regs = fbi->io;
+ void __iomem *irq_base = fbi->irq_base;
+ unsigned long lcdirq = readl(regs + REG_LCM_INT_CS);
+
+ if (lcdirq & LCM_INT_CS_DISP_F_STATUS) {
+ writel(readl(irq_base) | 1<<30, irq_base);
+
+ /* wait VA_EN low */
+ if ((readl(regs + REG_LCM_DCCS) &
+ LCM_DCCS_SINGLE) == LCM_DCCS_SINGLE)
+ while ((readl(regs + REG_LCM_DCCS) &
+ LCM_DCCS_VA_EN) == LCM_DCCS_VA_EN)
+ ;
+ /* display_out-enable */
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_DISP_OUT_EN,
+ regs + REG_LCM_DCCS);
+ /* va-enable*/
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_VA_EN,
+ regs + REG_LCM_DCCS);
+ } else if (lcdirq & LCM_INT_CS_UNDERRUN_INT) {
+ writel(readl(irq_base) | LCM_INT_CS_UNDERRUN_INT, irq_base);
+ } else if (lcdirq & LCM_INT_CS_BUS_ERROR_INT) {
+ writel(readl(irq_base) | LCM_INT_CS_BUS_ERROR_INT, irq_base);
+ }
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_CPU_FREQ
+
+static int nuc900fb_cpufreq_transition(struct notifier_block *nb,
+ unsigned long val, void *data)
+{
+ struct nuc900fb_info *info;
+ struct fb_info *fbinfo;
+ long delta_f;
+ info = container_of(nb, struct nuc900fb_info, freq_transition);
+ fbinfo = platform_get_drvdata(to_platform_device(info->dev));
+
+ delta_f = info->clk_rate - clk_get_rate(info->clk);
+
+ if ((val == CPUFREQ_POSTCHANGE && delta_f > 0) ||
+ (val == CPUFREQ_PRECHANGE && delta_f < 0)) {
+ info->clk_rate = clk_get_rate(info->clk);
+ nuc900fb_activate_var(fbinfo);
+ }
+
+ return 0;
+}
+
+static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
+{
+ fbi->freq_transition.notifier_call = nuc900fb_cpufreq_transition;
+ return cpufreq_register_notifier(&fbi->freq_transition,
+ CPUFREQ_TRANSITION_NOTIFIER);
+}
+
+static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *fbi)
+{
+ cpufreq_unregister_notifier(&fbi->freq_transition,
+ CPUFREQ_TRANSITION_NOTIFIER);
+}
+#else
+static inline int nuc900fb_cpufreq_transition(struct notifier_block *nb,
+ unsigned long val, void *data)
+{
+ return 0;
+}
+
+static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
+{
+ return 0;
+}
+
+static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *info)
+{
+}
+#endif
+
+static char driver_name[] = "nuc900fb";
+
+static int __init nuc900fb_probe(struct platform_device *pdev)
+{
+ struct nuc900fb_info *fbi;
+ struct nuc900fb_display *display;
+ struct fb_info *fbinfo;
+ struct nuc900fb_mach_info *mach_info;
+ struct resource *res;
+ int ret;
+ int irq;
+ int i;
+ int size;
+
+ dprintk("devinit\n");
+ mach_info = pdev->dev.platform_data;
+ if (mach_info == NULL) {
+ dev_err(&pdev->dev,
+ "no platform data for lcd, cannot attach\n");
+ return -EINVAL;
+ }
+
+ if (mach_info->default_display > mach_info->num_displays) {
+ dev_err(&pdev->dev,
+ "default display No. is %d but only %d displays \n",
+ mach_info->default_display, mach_info->num_displays);
+ return -EINVAL;
+ }
+
+
+ display = mach_info->displays + mach_info->default_display;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq for device\n");
+ return -ENOENT;
+ }
+
+ fbinfo = framebuffer_alloc(sizeof(struct nuc900fb_info), &pdev->dev);
+ if (!fbinfo)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, fbinfo);
+
+ fbi = fbinfo->par;
+ fbi->dev = &pdev->dev;
+
+#ifdef CONFIG_CPU_NUC950
+ fbi->drv_type = LCDDRV_NUC950;
+#endif
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ size = (res->end - res->start) + 1;
+ fbi->mem = request_mem_region(res->start, size, pdev->name);
+ if (fbi->mem == NULL) {
+ dev_err(&pdev->dev, "failed to alloc memory region\n");
+ ret = -ENOENT;
+ goto free_fb;
+ }
+
+ fbi->io = ioremap(res->start, size);
+ if (fbi->io == NULL) {
+ dev_err(&pdev->dev, "ioremap() of lcd registers failed\n");
+ ret = -ENXIO;
+ goto release_mem_region;
+ }
+
+ fbi->irq_base = fbi->io + REG_LCM_INT_CS;
+
+
+ /* Stop the LCD */
+ writel(0, fbi->io + REG_LCM_DCCS);
+
+ /* fill the fbinfo*/
+ strcpy(fbinfo->fix.id, driver_name);
+ fbinfo->fix.type = FB_TYPE_PACKED_PIXELS;
+ fbinfo->fix.type_aux = 0;
+ fbinfo->fix.xpanstep = 0;
+ fbinfo->fix.ypanstep = 0;
+ fbinfo->fix.ywrapstep = 0;
+ fbinfo->fix.accel = FB_ACCEL_NONE;
+ fbinfo->var.nonstd = 0;
+ fbinfo->var.activate = FB_ACTIVATE_NOW;
+ fbinfo->var.accel_flags = 0;
+ fbinfo->var.vmode = FB_VMODE_NONINTERLACED;
+ fbinfo->fbops = &nuc900fb_ops;
+ fbinfo->flags = FBINFO_FLAG_DEFAULT;
+ fbinfo->pseudo_palette = &fbi->pseudo_pal;
+
+ ret = request_irq(irq, nuc900fb_irqhandler, IRQF_DISABLED,
+ pdev->name, fbinfo);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot register irq handler %d -err %d\n",
+ irq, ret);
+ ret = -EBUSY;
+ goto release_regs;
+ }
+
+ nuc900_driver_clksrc_div(&pdev->dev, "ext", 0x2);
+
+ fbi->clk = clk_get(&pdev->dev, NULL);
+ if (!fbi->clk || IS_ERR(fbi->clk)) {
+ printk(KERN_ERR "nuc900-lcd:failed to get lcd clock source\n");
+ ret = -ENOENT;
+ goto release_irq;
+ }
+
+ clk_enable(fbi->clk);
+ dprintk("got and enabled clock\n");
+
+ fbi->clk_rate = clk_get_rate(fbi->clk);
+
+ /* calutate the video buffer size */
+ for (i = 0; i < mach_info->num_displays; i++) {
+ unsigned long smem_len = mach_info->displays[i].xres;
+ smem_len *= mach_info->displays[i].yres;
+ smem_len *= mach_info->displays[i].bpp;
+ smem_len >>= 3;
+ if (fbinfo->fix.smem_len < smem_len)
+ fbinfo->fix.smem_len = smem_len;
+ }
+
+ /* Initialize Video Memory */
+ ret = nuc900fb_map_video_memory(fbinfo);
+ if (ret) {
+ printk(KERN_ERR "Failed to allocate video RAM: %x\n", ret);
+ goto release_clock;
+ }
+
+ dprintk("got video memory\n");
+
+ fbinfo->var.xres = display->xres;
+ fbinfo->var.yres = display->yres;
+ fbinfo->var.bits_per_pixel = display->bpp;
+
+ nuc900fb_init_registers(fbinfo);
+
+ nuc900fb_check_var(&fbinfo->var, fbinfo);
+
+ ret = nuc900fb_cpufreq_register(fbi);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to register cpufreq\n");
+ goto free_video_memory;
+ }
+
+ ret = register_framebuffer(fbinfo);
+ if (ret) {
+ printk(KERN_ERR "failed to register framebuffer device: %d\n",
+ ret);
+ goto free_cpufreq;
+ }
+
+ /* create device files */
+ ret = device_create_file(&pdev->dev, &dev_attr_debug);
+ if (ret)
+ printk(KERN_ERR "failed to add debug attribute\n");
+
+
+ printk(KERN_INFO "fb%d: %s frame buffer device\n",
+ fbinfo->node, fbinfo->fix.id);
+
+ return 0;
+
+free_cpufreq:
+ nuc900fb_cpufreq_deregister(fbi);
+free_video_memory:
+ nuc900fb_unmap_video_memory(fbinfo);
+release_clock:
+ clk_disable(fbi->clk);
+ clk_put(fbi->clk);
+release_irq:
+ free_irq(irq, fbi);
+release_regs:
+ iounmap(fbi->io);
+release_mem_region:
+ release_mem_region((unsigned long)fbi->mem, size);
+free_fb:
+ framebuffer_release(fbinfo);
+ return ret;
+}
+
+/*
+ * shutdown the lcd controller
+ */
+static void nuc900fb_stop_lcd(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+ unsigned long flags;
+
+ local_irq_save(flags);
+ writel((~LCM_DCCS_DISP_INT_EN) | (~LCM_DCCS_VA_EN) | (~LCM_DCCS_OSD_EN),
+ regs + REG_LCM_DCCS);
+ local_irq_restore(flags);
+}
+
+/*
+ * Cleanup
+ */
+static int nuc900fb_remove(struct platform_device *pdev)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(pdev);
+ struct nuc900fb_info *fbi = fbinfo->par;
+ int irq;
+
+ nuc900fb_stop_lcd(fbinfo);
+ msleep(1);
+
+ nuc900fb_unmap_video_memory(fbinfo);
+
+ iounmap(fbi->io);
+
+ irq = platform_get_irq(pdev, 0);
+ free_irq(irq, fbi);
+
+ release_resource(fbi->mem);
+ kfree(fbi->mem);
+
+ platform_set_drvdata(pdev, NULL);
+ framebuffer_release(fbinfo);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+
+/*
+ * suspend and resume support for the lcd controller
+ */
+
+static int nuc900fb_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(dev);
+ struct nuc900fb_info *info = fbinfo->par;
+
+ nuc900fb_stop_lcd();
+ msleep(1);
+ clk_disable(info->clk);
+ return 0;
+}
+
+static int nuc900fb_resume(struct platform_device *dev)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(dev);
+ struct nuc900fb_info *fbi = fbinfo->par;
+
+ dprintk("nuc900fb resume\n");
+
+ clk_enable(fbi->clk);
+ msleep(1);
+
+ nuc900fb_init_registers(fbinfo);
+ nuc900fb_activate_var(bfinfo);
+
+ return 0;
+}
+
+#else
+#define nuc900fb_suspend NULL
+#define nuc900fb_resume NULL
+#endif
+
+static struct platform_driver nuc900fb_driver = {
+ .probe = nuc900fb_probe,
+ .remove = nuc900fb_remove,
+ .suspend = nuc900fb_suspend,
+ .resume = nuc900fb_resume,
+ .driver = {
+ .name = "nuc900-lcd",
+ .owner = THIS_MODULE,
+ },
+};
+
+int __devinit nuc900fb_init(void)
+{
+ return platform_driver_register(&nuc900fb_driver);
+}
+
+static void __exit nuc900fb_cleanup(void)
+{
+ platform_driver_unregister(&nuc900fb_driver);
+}
+
+module_init(nuc900fb_init);
+module_exit(nuc900fb_cleanup);
+
+MODULE_DESCRIPTION("Framebuffer driver for the NUC900");
+MODULE_LICENSE("GPL");
diff --git a/drivers/video/nuc900fb.h b/drivers/video/nuc900fb.h
new file mode 100644
index 0000000..6c23aa3
--- /dev/null
+++ b/drivers/video/nuc900fb.h
@@ -0,0 +1,55 @@
+/*
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Auther:
+ * Wang Qiang(rurality.linux at gmail.com) 2009/12/16
+ */
+
+#ifndef __NUC900FB_H
+#define __NUC900FB_H
+
+#include <mach/map.h>
+#include <mach/fb.h>
+
+enum nuc900_lcddrv_type {
+ LCDDRV_NUC910,
+ LCDDRV_NUC930,
+ LCDDRV_NUC932,
+ LCDDRV_NUC950,
+ LCDDRV_NUC960,
+};
+
+
+#define PALETTE_BUFFER_SIZE 256
+#define PALETTE_BUFF_CLEAR (0x80000000) /* entry is clear/invalid */
+
+struct nuc900fb_info {
+ struct device *dev;
+ struct clk *clk;
+
+ struct resource *mem;
+ void __iomem *io;
+ void __iomem *irq_base;
+ int drv_type;
+ struct nuc900fb_hw regs;
+ unsigned long clk_rate;
+
+#ifdef CONFIG_CPU_FREQ
+ struct notifier_block freq_transition;
+#endif
+
+ /* keep these registers in case we need to re-write palette */
+ u32 palette_buffer[PALETTE_BUFFER_SIZE];
+ u32 pseudo_pal[16];
+};
+
+int nuc900fb_init(void);
+
+#endif /* __NUC900FB_H */
--
1.6.4
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH]NUC900 LCD Controller Driver
2010-01-11 8:05 [PATCH]NUC900 LCD Controller Driver Wang Qiang
@ 2010-01-28 9:00 ` Qiang Wang
2010-01-30 0:27 ` Andrew Morton
1 sibling, 0 replies; 7+ messages in thread
From: Qiang Wang @ 2010-01-28 9:00 UTC (permalink / raw)
To: linux-arm-kernel
hello, Mr. Andrew Morton
This patch is for nuc900 platform.
Please check and ack.
Thank you very much.
best regards
Wang Qiang
2010/1/11 Wang Qiang <rurality.linux@gmail.com>:
> hi, Dear Wan
>
> There is the patch of LCD controller driver for nuc900s.
> The Linux LOGO is just fine and the FB-Test application was ok, too.
>
> best regards
> wangqiang
>
> Signed-off-by: Wang Qiang <rurality.linux@gmail.com>
> Cc:Wang Zongshun <mcuos.com@gmail.com>
> ---
> diff --git a/arch/arm/configs/nuc950_defconfig
> b/arch/arm/configs/nuc950_defconfig
> index 97300ec..51cc2a2 100644
> --- a/arch/arm/configs/nuc950_defconfig
> +++ b/arch/arm/configs/nuc950_defconfig
> @@ -590,8 +590,40 @@ CONFIG_SSB_POSSIBLE=y
> ?#
> ?# CONFIG_VGASTATE is not set
> ?# CONFIG_VIDEO_OUTPUT_CONTROL is not set
> -# CONFIG_FB is not set
> ?# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
> +CONFIG_FB=y
> +# CONFIG_FIRMWARE_EDID is not set
> +# CONFIG_FB_DDC is not set
> +# CONFIG_FB_BOOT_VESA_SUPPORT is not set
> +CONFIG_FB_CFB_FILLRECT=y
> +CONFIG_FB_CFB_COPYAREA=y
> +CONFIG_FB_CFB_IMAGEBLIT=y
> +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
> +# CONFIG_FB_SYS_FILLRECT is not set
> +# CONFIG_FB_SYS_COPYAREA is not set
> +# CONFIG_FB_SYS_IMAGEBLIT is not set
> +# CONFIG_FB_FOREIGN_ENDIAN is not set
> +# CONFIG_FB_SYS_FOPS is not set
> +# CONFIG_FB_SVGALIB is not set
> +# CONFIG_FB_MACMODES is not set
> +# CONFIG_FB_BACKLIGHT is not set
> +# CONFIG_FB_MODE_HELPERS is not set
> +# CONFIG_FB_TILEBLITTING is not set
> +
> +#
> +# Frame buffer hardware drivers
> +#
> +# CONFIG_FB_S1D13XXX is not set
> +CONFIG_FB_NUC900=y
> +CONFIG_GPM1040A0_320X240=y
> +CONFIG_FB_NUC900_DEBUG=y
> +# CONFIG_FB_VIRTUAL is not set
> +# CONFIG_FB_METRONOME is not set
> +# CONFIG_FB_MB862XX is not set
> +# CONFIG_FB_BROADSHEET is not set
> +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
> +
> +
>
> ?#
> ?# Display device support
> @@ -603,6 +635,25 @@ CONFIG_SSB_POSSIBLE=y
> ?#
> ?# CONFIG_VGA_CONSOLE is not set
> ?CONFIG_DUMMY_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE=y
> +CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
> +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
> +CONFIG_FONTS=y
> +# CONFIG_FONT_8x8 is not set
> +CONFIG_FONT_8x16=y
> +# CONFIG_FONT_6x11 is not set
> +# CONFIG_FONT_7x14 is not set
> +# CONFIG_FONT_PEARL_8x8 is not set
> +# CONFIG_FONT_ACORN_8x8 is not set
> +# CONFIG_FONT_MINI_4x6 is not set
> +# CONFIG_FONT_SUN8x16 is not set
> +# CONFIG_FONT_SUN12x22 is not set
> +# CONFIG_FONT_10x18 is not set
> +CONFIG_LOGO=y
> +# CONFIG_LOGO_LINUX_MONO is not set
> +# CONFIG_LOGO_LINUX_VGA16 is not set
> +CONFIG_LOGO_LINUX_CLUT224=y
> +
> ?# CONFIG_SOUND is not set
> ?# CONFIG_HID_SUPPORT is not set
> ?CONFIG_USB_SUPPORT=y
> diff --git a/arch/arm/mach-w90x900/cpu.h b/arch/arm/mach-w90x900/cpu.h
> index 4d58ba1..f8730b6 100644
> --- a/arch/arm/mach-w90x900/cpu.h
> +++ b/arch/arm/mach-w90x900/cpu.h
> @@ -57,3 +57,4 @@ extern struct platform_device nuc900_device_fmi;
> ?extern struct platform_device nuc900_device_kpi;
> ?extern struct platform_device nuc900_device_rtc;
> ?extern struct platform_device nuc900_device_ts;
> +extern struct platform_device nuc900_device_lcd;
> diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c
> index ec711f4..298c7a2 100644
> --- a/arch/arm/mach-w90x900/dev.c
> +++ b/arch/arm/mach-w90x900/dev.c
> @@ -34,6 +34,7 @@
> ?#include <mach/regs-serial.h>
> ?#include <mach/nuc900_spi.h>
> ?#include <mach/map.h>
> +#include <mach/fb.h>
>
> ?#include "cpu.h"
>
> @@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
> ? ? ? ?.resource ? ? ? = nuc900_kpi_resource,
> ?};
>
> +#ifdef CONFIG_FB_NUC900
> +
> +static struct resource nuc900_lcd_resource[] = {
> + ? ? ? [0] = {
> + ? ? ? ? ? ? ? .start = W90X900_PA_LCD,
> + ? ? ? ? ? ? ? .end ? = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
> + ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
> + ? ? ? },
> + ? ? ? [1] = {
> + ? ? ? ? ? ? ? .start = IRQ_LCD,
> + ? ? ? ? ? ? ? .end ? = IRQ_LCD,
> + ? ? ? ? ? ? ? .flags = IORESOURCE_IRQ,
> + ? ? ? }
> +};
> +
> +static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
> +
> +struct platform_device nuc900_device_lcd = {
> + ? ? ? .name ? ? ? ? ? ? = "nuc900-lcd",
> + ? ? ? .id ? ? ? ? ? ? ? = -1,
> + ? ? ? .num_resources ? ?= ARRAY_SIZE(nuc900_lcd_resource),
> + ? ? ? .resource ? ? ? ? = nuc900_lcd_resource,
> + ? ? ? .dev ? ? ? ? ? ? ?= {
> + ? ? ? ? ? ? ? .dma_mask ? ? ? ? ? ? ? = &nuc900_device_lcd_dmamask,
> + ? ? ? ? ? ? ? .coherent_dma_mask ? ? ?= 0xffffffffUL
> + ? ? ? }
> +};
> +
> +void ?nuc900_fb_set_platdata(struct nuc900fb_mach_info *pd)
> +{
> + ? ? ? struct nuc900fb_mach_info *npd;
> +
> + ? ? ? npd = kmalloc(sizeof(*npd), GFP_KERNEL);
> + ? ? ? if (npd) {
> + ? ? ? ? ? ? ? memcpy(npd, pd, sizeof(*npd));
> + ? ? ? ? ? ? ? nuc900_device_lcd.dev.platform_data = npd;
> + ? ? ? } else {
> + ? ? ? ? ? ? ? printk(KERN_ERR "no memory for LCD platform data\n");
> + ? ? ? }
> +}
> +#endif
> +
> ?/*Here should be your evb resourse,such as LCD*/
>
> ?static struct platform_device *nuc900_public_dev[] __initdata = {
> diff --git a/arch/arm/mach-w90x900/include/mach/fb.h
> b/arch/arm/mach-w90x900/include/mach/fb.h
> new file mode 100644
> index 0000000..cec5ece
> --- /dev/null
> +++ b/arch/arm/mach-w90x900/include/mach/fb.h
> @@ -0,0 +1,83 @@
> +/* linux/include/asm/arch-nuc900/fb.h
> + *
> + * Copyright (c) 2008 Nuvoton technology corporation
> + * All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * Changelog:
> + *
> + * ? 2008/08/26 ? ? vincen.zswan modify this file for LCD.
> + */
> +
> +#ifndef __ASM_ARM_FB_H
> +#define __ASM_ARM_FB_H
> +
> +
> +
> +/* LCD Controller Hardware Desc */
> +struct nuc900fb_hw {
> + ? ? ? unsigned int lcd_dccs;
> + ? ? ? unsigned int lcd_device_ctrl;
> + ? ? ? unsigned int lcd_mpulcd_cmd;
> + ? ? ? unsigned int lcd_int_cs;
> + ? ? ? unsigned int lcd_crtc_size;
> + ? ? ? unsigned int lcd_crtc_dend;
> + ? ? ? unsigned int lcd_crtc_hr;
> + ? ? ? unsigned int lcd_crtc_hsync;
> + ? ? ? unsigned int lcd_crtc_vr;
> + ? ? ? unsigned int lcd_va_baddr0;
> + ? ? ? unsigned int lcd_va_baddr1;
> + ? ? ? unsigned int lcd_va_fbctrl;
> + ? ? ? unsigned int lcd_va_scale;
> + ? ? ? unsigned int lcd_va_test;
> + ? ? ? unsigned int lcd_va_win;
> + ? ? ? unsigned int lcd_va_stuff;
> +};
> +
> +/* LCD Display Description */
> +struct nuc900fb_display {
> + ? ? ? /* LCD Image type */
> + ? ? ? unsigned type;
> +
> + ? ? ? /* LCD Screen Size */
> + ? ? ? unsigned short width;
> + ? ? ? unsigned short height;
> +
> + ? ? ? /* LCD Screen Info */
> + ? ? ? unsigned short xres;
> + ? ? ? unsigned short yres;
> + ? ? ? unsigned short bpp;
> +
> + ? ? ? unsigned long pixclock;
> + ? ? ? unsigned short left_margin;
> + ? ? ? unsigned short right_margin;
> + ? ? ? unsigned short hsync_len;
> + ? ? ? unsigned short upper_margin;
> + ? ? ? unsigned short lower_margin;
> + ? ? ? unsigned short vsync_len;
> +
> + ? ? ? /* hardware special register value */
> + ? ? ? unsigned int dccs;
> + ? ? ? unsigned int devctl;
> + ? ? ? unsigned int fbctrl;
> + ? ? ? unsigned int scale;
> +};
> +
> +struct nuc900fb_mach_info {
> + ? ? ? struct nuc900fb_display *displays;
> + ? ? ? unsigned num_displays;
> + ? ? ? unsigned default_display;
> + ? ? ? /* GPIO Setting ?Info */
> + ? ? ? unsigned gpio_dir;
> + ? ? ? unsigned gpio_dir_mask;
> + ? ? ? unsigned gpio_data;
> + ? ? ? unsigned gpio_data_mask;
> +};
> +
> +extern void __init nuc900_fb_set_platdata(struct nuc900fb_mach_info *);
> +
> +#endif /* __ASM_ARM_FB_H */
> diff --git a/arch/arm/mach-w90x900/include/mach/regs-ldm.h
> b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
> new file mode 100644
> index 0000000..e9d480a
> --- /dev/null
> +++ b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
> @@ -0,0 +1,253 @@
> +/*
> + * arch/arm/mach-w90x900/include/mach/regs-serial.h
> + *
> + * Copyright (c) 2009 Nuvoton technology corporation
> + * All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * ?Description:
> + * ? ? Nuvoton Display, LCM Register list
> + * ?Author: ?Wang Qiang (rurality.linux at gmail.com) 2009/12/11
> + *
> + */
> +
> +
> +#ifndef __ASM_ARM_W90X900_REGS_LDM_H
> +#define __ASM_ARM_W90X900_REGS_LDM_H
> +
> +#include <mach/map.h>
> +
> +/* Display Controller Control/Status Register */
> +#define REG_LCM_DCCS ? ? ? ? ? ? ? ? ? (0x00)
> +
> +#define LCM_DCCS_ENG_RST ? ? ? ? ? ? ? (1 << 0)
> +#define LCM_DCCS_VA_EN ? ? ? ? ? ? ? ? (1 << 1)
> +#define LCM_DCCS_OSD_EN ? ? ? ? ? ? ? ? ? ? ? ?(1 << 2)
> +#define LCM_DCCS_DISP_OUT_EN ? ? ? ? ? (1 << 3)
> +#define LCM_DCCS_DISP_INT_EN ? ? ? ? ? (1 << 4)
> +#define LCM_DCCS_CMD_ON ? ? ? ? ? ? ? ? ? ? ? ?(1 << 5)
> +#define LCM_DCCS_FIELD_INTR ? ? ? ? ? ?(1 << 6)
> +#define LCM_DCCS_SINGLE ? ? ? ? ? ? ? ? ? ? ? ?(1 << 7)
> +
> +enum LCM_DCCS_VA_SRC {
> + ? ? ? LCM_DCCS_VA_SRC_YUV422 ? ? ? ? ?= (0 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_YCBCR422 ? ? ? ?= (1 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_RGB888 ? ? ? ? ?= (2 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_RGB666 ? ? ? ? ?= (3 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_RGB565 ? ? ? ? ?= (4 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_RGB444LOW ? ? ? = (5 << 8),
> + ? ? ? LCM_DCCS_VA_SRC_RGB444HIGH ? ? ?= (7 << 8)
> +};
> +
> +
> +/* Display Device Control Register */
> +#define REG_LCM_DEV_CTRL ? ? ? ? ? ? ? (0x04)
> +
> +enum LCM_DEV_CTRL_SWAP_YCbCr {
> + ? ? ? LCM_DEV_CTRL_SWAP_UYVY ? ? ? ? ?= (0 << 1),
> + ? ? ? LCM_DEV_CTRL_SWAP_YUYV ? ? ? ? ?= (1 << 1),
> + ? ? ? LCM_DEV_CTRL_SWAP_VYUY ? ? ? ? ?= (2 << 1),
> + ? ? ? LCM_DEV_CTRL_SWAP_YVYU ? ? ? ? ?= (3 << 1)
> +};
> +
> +enum LCM_DEV_CTRL_RGB_SHIFT {
> + ? ? ? LCM_DEV_CTRL_RGB_SHIFT_NOT ? ? ?= (0 << 3),
> + ? ? ? LCM_DEV_CTRL_RGB_SHIFT_ONECYCLE = (1 << 3),
> + ? ? ? LCM_DEV_CTRL_RGB_SHIFT_TWOCYCLE = (2 << 3),
> + ? ? ? LCM_DEV_CTRL_RGB_SHIFT_NOT_DEF ?= (3 << 3)
> +};
> +
> +enum LCM_DEV_CTRL_DEVICE {
> + ? ? ? LCM_DEV_CTRL_DEVICE_YUV422 ? ? ?= (0 << 5),
> + ? ? ? LCM_DEV_CTRL_DEVICE_YUV444 ? ? ?= (1 << 5),
> + ? ? ? LCM_DEV_CTRL_DEVICE_UNIPAC ? ? ?= (4 << 5),
> + ? ? ? LCM_DEV_CTRL_DEVICE_SEIKO_EPSON = (5 << 5),
> + ? ? ? LCM_DEV_CTRL_DEVICE_HIGH_COLOR ?= (6 << 5),
> + ? ? ? LCM_DEV_CTRL_DEVICE_MPU ? ? ? ? = (7 << 5)
> +};
> +
> +#define LCM_DEV_CTRL_LCD_DDA ? ? ? ? ? (8)
> +#define LCM_DEV_CTRL_YUV2CCIR ? ? ? ? ?(16)
> +
> +enum LCM_DEV_CTRL_LCD_SEL {
> + ? ? ? LCM_DEV_CTRL_LCD_SEL_RGB_GBR ? ?= (0 << 17),
> + ? ? ? LCM_DEV_CTRL_LCD_SEL_BGR_RBG ? ?= (1 << 17),
> + ? ? ? LCM_DEV_CTRL_LCD_SEL_GBR_RGB ? ?= (2 << 17),
> + ? ? ? LCM_DEV_CTRL_LCD_SEL_RBG_BGR ? ?= (3 << 17)
> +};
> +
> +enum LCM_DEV_CTRL_FAL_D {
> + ? ? ? LCM_DEV_CTRL_FAL_D_FALLING ? ? ?= (0 << 19),
> + ? ? ? LCM_DEV_CTRL_FAL_D_RISING ? ? ? = (1 << 19),
> +};
> +
> +enum LCM_DEV_CTRL_H_POL {
> + ? ? ? LCM_DEV_CTRL_H_POL_LOW ? ? ? ? ?= (0 << 20),
> + ? ? ? LCM_DEV_CTRL_H_POL_HIGH ? ? ? ? = (1 << 20),
> +};
> +
> +enum LCM_DEV_CTRL_V_POL {
> + ? ? ? LCM_DEV_CTRL_V_POL_LOW ? ? ? ? ?= (0 << 21),
> + ? ? ? LCM_DEV_CTRL_V_POL_HIGH ? ? ? ? = (1 << 21),
> +};
> +
> +enum LCM_DEV_CTRL_VR_LACE {
> + ? ? ? LCM_DEV_CTRL_VR_LACE_NINTERLACE = (0 << 22),
> + ? ? ? LCM_DEV_CTRL_VR_LACE_INTERLACE ?= (1 << 22),
> +};
> +
> +enum LCM_DEV_CTRL_LACE {
> + ? ? ? LCM_DEV_CTRL_LACE_NINTERLACE ? ?= (0 << 23),
> + ? ? ? LCM_DEV_CTRL_LACE_INTERLACE ? ? = (1 << 23),
> +};
> +
> +enum LCM_DEV_CTRL_RGB_SCALE {
> + ? ? ? LCM_DEV_CTRL_RGB_SCALE_4096 ? ? = (0 << 24),
> + ? ? ? LCM_DEV_CTRL_RGB_SCALE_65536 ? ?= (1 << 24),
> + ? ? ? LCM_DEV_CTRL_RGB_SCALE_262144 ? = (2 << 24),
> + ? ? ? LCM_DEV_CTRL_RGB_SCALE_16777216 = (3 << 24),
> +};
> +
> +enum LCM_DEV_CTRL_DBWORD {
> + ? ? ? LCM_DEV_CTRL_DBWORD_HALFWORD ? ?= (0 << 26),
> + ? ? ? LCM_DEV_CTRL_DBWORD_FULLWORD ? ?= (1 << 26),
> +};
> +
> +enum LCM_DEV_CTRL_MPU68 {
> + ? ? ? LCM_DEV_CTRL_MPU68_80_SERIES ? ?= (0 << 27),
> + ? ? ? LCM_DEV_CTRL_MPU68_68_SERIES ? ?= (1 << 27),
> +};
> +
> +enum LCM_DEV_CTRL_DE_POL {
> + ? ? ? LCM_DEV_CTRL_DE_POL_HIGH ? ? ? ?= (0 << 28),
> + ? ? ? LCM_DEV_CTRL_DE_POL_LOW ? ? ? ? = (1 << 28),
> +};
> +
> +#define LCM_DEV_CTRL_CMD16 ? ? ? ? ? ? (29)
> +#define LCM_DEV_CTRL_CM16t18 ? ? ? ? ? (30)
> +#define LCM_DEV_CTRL_CMD_LOW ? ? ? ? ? (31)
> +
> +/* MPU-Interface LCD Write Command */
> +#define REG_LCM_MPU_CMD ? ? ? ? ? ? ? ? ? ? ? ?(0x08)
> +
> +/* Interrupt Control/Status Register */
> +#define REG_LCM_INT_CS ? ? ? ? ? ? ? ? (0x0c)
> +#define LCM_INT_CS_DISP_F_EN ? ? ? ? ? (1 << 0)
> +#define LCM_INT_CS_UNDERRUN_EN ? ? ? ? (1 << 1)
> +#define LCM_INT_CS_BUS_ERROR_INT ? ? ? (1 << 28)
> +#define LCM_INT_CS_UNDERRUN_INT ? ? ? ?(1 << 29)
> +#define LCM_INT_CS_DISP_F_STATUS ? ? ? (1 << 30)
> +#define LCM_INT_CS_DISP_F_INT ? ? ? ? ?(1 << 31)
> +
> +/* CRTC Display Size Control Register */
> +#define REG_LCM_CRTC_SIZE ? ? ? ? ? ? ?(0x10)
> +#define LCM_CRTC_SIZE_VTTVAL(x) ? ? ? ? ? ? ? ?((x) << 16)
> +#define LCM_CRTC_SIZE_HTTVAL(x) ? ? ? ? ? ? ? ?((x) << 0)
> +
> +/* CRTC Display Enable End */
> +#define REG_LCM_CRTC_DEND ? ? ? ? ? ? ?(0x14)
> +#define LCM_CRTC_DEND_VDENDVAL(x) ? ? ?((x) << 16)
> +#define LCM_CRTC_DEND_HDENDVAL(x) ? ? ?((x) << 0)
> +
> +/* CRTC Internal Horizontal Retrace Control Register */
> +#define REG_LCM_CRTC_HR ? ? ? ? ? ? ? ? ? ? ? ?(0x18)
> +#define LCM_CRTC_HR_EVAL(x) ? ? ? ? ? ?((x) << 16)
> +#define LCM_CRTC_HR_SVAL(x) ? ? ? ? ? ?((x) << 0)
> +
> +/* CRTC Horizontal Sync Control Register */
> +#define REG_LCM_CRTC_HSYNC ? ? ? ? ? ? (0x1C)
> +#define LCM_CRTC_HSYNC_SHIFTVAL(x) ? ? ((x) << 30)
> +#define LCM_CRTC_HSYNC_EVAL(x) ? ? ? ? ((x) << 16)
> +#define LCM_CRTC_HSYNC_SVAL(x) ? ? ? ? ((x) << 0)
> +
> +/* CRTC Internal Vertical Retrace Control Register */
> +#define REG_LCM_CRTC_VR ? ? ? ? ? ? ? ? ? ? ? ?(0x20)
> +#define LCM_CRTC_VR_EVAL(x) ? ? ? ? ? ?((x) << 16)
> +#define LCM_CRTC_VR_SVAL(x) ? ? ? ? ? ?((x) << 0)
> +
> +/* Video Stream Frame Buffer-0 Starting Address */
> +#define REG_LCM_VA_BADDR0 ? ? ? ? ? ? ?(0x24)
> +
> +/* Video Stream Frame Buffer-1 Starting Address */
> +#define REG_LCM_VA_BADDR1 ? ? ? ? ? ? ?(0x28)
> +
> +/* Video Stream Frame Buffer Control Register */
> +#define REG_LCM_VA_FBCTRL ? ? ? ? ? ? ?(0x2C)
> +#define LCM_VA_FBCTRL_IO_REGION_HALF ? (1 << 28)
> +#define LCM_VA_FBCTRL_FIELD_DUAL ? ? ? (1 << 29)
> +#define LCM_VA_FBCTRL_START_BUF ? ? ? ?(1 << 30)
> +#define LCM_VA_FBCTRL_DB_EN ? ? ? ? ? ?(1 << 31)
> +
> +/* Video Stream Scaling Control Register */
> +#define REG_LCM_VA_SCALE ? ? ? ? ? ? ? (0x30)
> +#define LCM_VA_SCALE_XCOPY_INTERPOLATION (0 << 15)
> +#define LCM_VA_SCALE_XCOPY_DUPLICATION ?(1 << 15)
> +
> +/* Image Stream Active Window Coordinates */
> +#define REG_LCM_VA_WIN ? ? ? ? ? ? ? ? (0x38)
> +
> +/* Image Stream Stuff Pixel */
> +#define REG_LCM_VA_STUFF ? ? ? ? ? ? ? (0x3C)
> +
> +/* OSD Window Starting Coordinates */
> +#define REG_LCM_OSD_WINS ? ? ? ? ? ? ? (0x40)
> +
> +/* OSD Window Ending Coordinates */
> +#define REG_LCM_OSD_WINE ? ? ? ? ? ? ? (0x44)
> +
> +/* OSD Stream Frame Buffer Starting Address */
> +#define REG_LCM_OSD_BADDR ? ? ? ? ? ? ?(0x48)
> +
> +/* OSD Stream Frame Buffer Control Register */
> +#define REG_LCM_OSD_FBCTRL ? ? ? ? ? ? (0x4c)
> +
> +/* OSD Overlay Control Register */
> +#define REG_LCM_OSD_OVERLAY ? ? ? ? ? ?(0x50)
> +
> +/* OSD Overlay Color-Key Pattern Register */
> +#define REG_LCM_OSD_CKEY ? ? ? ? ? ? ? (0x54)
> +
> +/* OSD Overlay Color-Key Mask Register */
> +#define REG_LCM_OSD_CMASK ? ? ? ? ? ? ?(0x58)
> +
> +/* OSD Window Skip1 Register */
> +#define REG_LCM_OSD_SKIP1 ? ? ? ? ? ? ?(0x5C)
> +
> +/* OSD Window Skip2 Register */
> +#define REG_LCM_OSD_SKIP2 ? ? ? ? ? ? ?(0x60)
> +
> +/* OSD horizontal up scaling control register */
> +#define REG_LCM_OSD_SCALE ? ? ? ? ? ? ?(0x64)
> +
> +/* MPU Vsync control register */
> +#define REG_LCM_MPU_VSYNC ? ? ? ? ? ? ?(0x68)
> +
> +/* Hardware cursor control Register */
> +#define REG_LCM_HC_CTRL ? ? ? ? ? ? ? ? ? ? ? ?(0x6C)
> +
> +/* Hardware cursot tip point potison on va picture */
> +#define REG_LCM_HC_POS ? ? ? ? ? ? ? ? (0x70)
> +
> +/* Hardware Cursor Window Buffer Control Register */
> +#define REG_LCM_HC_WBCTRL ? ? ? ? ? ? ?(0x74)
> +
> +/* Hardware cursor memory base address register */
> +#define REG_LCM_HC_BADDR ? ? ? ? ? ? ? (0x78)
> +
> +/* Hardware cursor color ram register mapped to bpp = 0 */
> +#define REG_LCM_HC_COLOR0 ? ? ? ? ? ? ?(0x7C)
> +
> +/* Hardware cursor color ram register mapped to bpp = 1 */
> +#define REG_LCM_HC_COLOR1 ? ? ? ? ? ? ?(0x80)
> +
> +/* Hardware cursor color ram register mapped to bpp = 2 */
> +#define REG_LCM_HC_COLOR2 ? ? ? ? ? ? ?(0x84)
> +
> +/* Hardware cursor color ram register mapped to bpp = 3 */
> +#define REG_LCM_HC_COLOR3 ? ? ? ? ? ? ?(0x88)
> +
> +#endif /* __ASM_ARM_W90X900_REGS_LDM_H */
> diff --git a/arch/arm/mach-w90x900/mach-nuc950evb.c
> b/arch/arm/mach-w90x900/mach-nuc950evb.c
> index cef903b..b3edc3c 100644
> --- a/arch/arm/mach-w90x900/mach-nuc950evb.c
> +++ b/arch/arm/mach-w90x900/mach-nuc950evb.c
> @@ -10,6 +10,8 @@
> ?* This program is free software; you can redistribute it and/or
> ?* modify it under the terms of the GNU General Public License as
> ?* published by the Free Software Foundation;version 2 of the License.
> + * ? history:
> + * ? ? Wang Qiang (rurality.linux at gmail.com) add LCD support
> ?*
> ?*/
>
> @@ -18,9 +20,51 @@
> ?#include <asm/mach/map.h>
> ?#include <asm/mach-types.h>
> ?#include <mach/map.h>
> +#include <mach/regs-ldm.h>
> +#include <mach/fb.h>
>
> ?#include "nuc950.h"
>
> +#ifdef CONFIG_FB_NUC900
> +/* LCD Controller */
> +static struct nuc900fb_display __initdata nuc950_lcd_info[] = {
> + ? ? ? /* Giantplus Technology GPM1040A0 320x240 Color TFT LCD */
> + ? ? ? [0] = {
> + ? ? ? ? ? ? ? .type ? ? ? ? ? = LCM_DCCS_VA_SRC_RGB565,
> + ? ? ? ? ? ? ? .width ? ? ? ? ?= 320,
> + ? ? ? ? ? ? ? .height ? ? ? ? = 240,
> + ? ? ? ? ? ? ? .xres ? ? ? ? ? = 320,
> + ? ? ? ? ? ? ? .yres ? ? ? ? ? = 240,
> + ? ? ? ? ? ? ? .bpp ? ? ? ? ? ?= 16,
> + ? ? ? ? ? ? ? .pixclock ? ? ? = 200000,
> + ? ? ? ? ? ? ? .left_margin ? ?= 34,
> + ? ? ? ? ? ? ? .right_margin ? = 54,
> + ? ? ? ? ? ? ? .hsync_len ? ? ?= 10,
> + ? ? ? ? ? ? ? .upper_margin ? = 18,
> + ? ? ? ? ? ? ? .lower_margin ? = 4,
> + ? ? ? ? ? ? ? .vsync_len ? ? ?= 1,
> + ? ? ? ? ? ? ? .dccs ? ? ? ? ? = 0x8e00041a,
> + ? ? ? ? ? ? ? .devctl ? ? ? ? = 0x060800c0,
> + ? ? ? ? ? ? ? .fbctrl ? ? ? ? = 0x00a000a0,
> + ? ? ? ? ? ? ? .scale ? ? ? ? ?= 0x04000400,
> + ? ? ? },
> +};
> +
> +static struct nuc900fb_mach_info nuc950_fb_info __initdata = {
> +#if defined(CONFIG_GPM1040A0_320X240)
> + ? ? ? .displays ? ? ? ? ? ? ? = &nuc950_lcd_info[0],
> +#else
> + ? ? ? .displays ? ? ? ? ? ? ? = nuc950_lcd_info,
> +#endif
> + ? ? ? .num_displays ? ? ? ? ? = ARRAY_SIZE(nuc950_lcd_info),
> + ? ? ? .default_display ? ? ? ?= 0,
> + ? ? ? .gpio_dir ? ? ? ? ? ? ? = 0x00000004,
> + ? ? ? .gpio_dir_mask ? ? ? ? ?= 0xFFFFFFFD,
> + ? ? ? .gpio_data ? ? ? ? ? ? ?= 0x00000004,
> + ? ? ? .gpio_data_mask ? ? ? ? = 0xFFFFFFFD,
> +};
> +#endif
> +
> ?static void __init nuc950evb_map_io(void)
> ?{
> ? ? ? ?nuc950_map_io();
> @@ -30,6 +74,9 @@ static void __init nuc950evb_map_io(void)
> ?static void __init nuc950evb_init(void)
> ?{
> ? ? ? ?nuc950_board_init();
> +#ifdef CONFIG_FB_NUC900
> + ? ? ? nuc900_fb_set_platdata(&nuc950_fb_info);
> +#endif
> ?}
>
> ?MACHINE_START(W90P950EVB, "W90P950EVB")
> diff --git a/arch/arm/mach-w90x900/nuc950.c b/arch/arm/mach-w90x900/nuc950.c
> index 1495081..4d1f1ab 100644
> --- a/arch/arm/mach-w90x900/nuc950.c
> +++ b/arch/arm/mach-w90x900/nuc950.c
> @@ -18,6 +18,7 @@
> ?#include <linux/platform_device.h>
> ?#include <asm/mach/map.h>
> ?#include <mach/hardware.h>
> +
> ?#include "cpu.h"
>
> ?/* define specific CPU platform device */
> @@ -25,6 +26,9 @@
> ?static struct platform_device *nuc950_dev[] __initdata = {
> ? ? ? ?&nuc900_device_kpi,
> ? ? ? ?&nuc900_device_fmi,
> +#ifdef CONFIG_FB_NUC900
> + ? ? ? &nuc900_device_lcd,
> +#endif
> ?};
>
> ?/* define specific CPU platform io map */
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 5a5c303..a943e5e 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -1945,6 +1945,27 @@ config FB_S3C2410_DEBUG
> ? ? ? ? ?Turn on debugging messages. Note that you can set/unset at run time
> ? ? ? ? ?through sysfs
>
> +config FB_NUC900
> + ? ? ? ?bool "NUC900 LCD framebuffer support"
> + ? ? ? ?depends on FB && ARCH_W90X900
> + ? ? ? ?select FB_CFB_FILLRECT
> + ? ? ? ?select FB_CFB_COPYAREA
> + ? ? ? ?select FB_CFB_IMAGEBLIT
> + ? ? ? ?---help---
> + ? ? ? ? ?Frame buffer driver for the built-in LCD controller in the Nuvoton
> + ? ? ? ? ?NUC900 processor
> +
> +config GPM1040A0_320X240
> + ? ? ? ?bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
> + ? ? ? ?depends on FB_NUC900
> +
> +config FB_NUC900_DEBUG
> + ? ? ? ?bool "NUC900 lcd debug messages"
> + ? ? ? ?depends on FB_NUC900
> + ? ? ? ?help
> + ? ? ? ? ?Turn on debugging messages. Note that you can set/unset at run time
> + ? ? ? ? ?through sysfs
> +
> ?config FB_SM501
> ? ? ? ?tristate "Silicon Motion SM501 framebuffer support"
> ? ? ? ?depends on FB && MFD_SM501
> diff --git a/drivers/video/Makefile b/drivers/video/Makefile
> index 4ecb30c..a42ad55 100644
> --- a/drivers/video/Makefile
> +++ b/drivers/video/Makefile
> @@ -129,6 +129,7 @@ obj-$(CONFIG_XEN_FBDEV_FRONTEND) ?+= xen-fbfront.o
> ?obj-$(CONFIG_FB_CARMINE) ? ? ? ? ?+= carminefb.o
> ?obj-$(CONFIG_FB_MB862XX) ? ? ? ? += mb862xx/
> ?obj-$(CONFIG_FB_MSM) ? ? ? ? ? ? ?+= msm/
> +obj-$(CONFIG_FB_NUC900) ? ? ? ? ? += nuc900fb.o
>
> ?# Platform or fallback drivers go here
> ?obj-$(CONFIG_FB_UVESA) ? ? ? ? ? ?+= uvesafb.o
> diff --git a/drivers/video/nuc900fb.c b/drivers/video/nuc900fb.c
> new file mode 100644
> index 0000000..c4ff225
> --- /dev/null
> +++ b/drivers/video/nuc900fb.c
> @@ -0,0 +1,842 @@
> +/*
> + *
> + * Copyright (c) 2009 Nuvoton technology corporation
> + * All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * ?Description:
> + * ? ?Nuvoton LCD Controller Driver
> + * ?Author:
> + * ? ?Wang Qiang (rurality.linux at gmail.com) 2009/12/11
> + */
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/mm.h>
> +#include <linux/tty.h>
> +#include <linux/slab.h>
> +#include <linux/delay.h>
> +#include <linux/fb.h>
> +#include <linux/init.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/interrupt.h>
> +#include <linux/workqueue.h>
> +#include <linux/wait.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/cpufreq.h>
> +#include <linux/io.h>
> +
> +#ifdef CONFIG_PM
> +#include <linux/pm.h>
> +#endif
> +
> +#include <mach/map.h>
> +#include <mach/regs-clock.h>
> +#include <mach/regs-ldm.h>
> +#include <mach/fb.h>
> +#include <mach/clkdev.h>
> +
> +#include "nuc900fb.h"
> +
> +/* Debugging stuff */
> +#ifdef CONFIG_FB_NUC900_DEBUG
> +static int debug ? ? ? = 1;
> +#define dprintk(msg...) ? ? ? ?{ printk(KERN_DEBUG "nuc900 lcd: " msg); }
> +#else
> +static int debug;
> +#define dprintk(msg...)
> +#endif
> +
> +
> +/*
> + * ?Initialize the nuc900 video (dual) buffer address
> + */
> +static void nuc900fb_set_lcdaddr(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? void __iomem *regs = fbi->io;
> + ? ? ? unsigned long vbaddr1, vbaddr2;
> + ? ? ? vbaddr1 ?= info->fix.smem_start;
> + ? ? ? vbaddr2 ?= info->fix.smem_start;
> + ? ? ? vbaddr2 += info->fix.line_length * info->var.yres;
> + ? ? ? /*set frambuffer start phy addr*/
> + ? ? ? writel(vbaddr1, regs + REG_LCM_VA_BADDR0);
> + ? ? ? writel(vbaddr2, regs + REG_LCM_VA_BADDR1);
> +
> + ? ? ? writel(fbi->regs.lcd_va_fbctrl, regs + REG_LCM_VA_FBCTRL);
> + ? ? ? writel(fbi->regs.lcd_va_scale, regs + REG_LCM_VA_SCALE);
> +}
> +
> +//static void nuc900fb_clk_select(struct fb_info *info, unsigned long pixclk)
> +//{
> +// ? ? struct nuc900fb_info *fbi = info->par;
> +// ? ? int div;
> +// ? ? if (clk <= 15 * 1000 * 1000) {
> +// ? ? ? ? ? ? div = (15 * 1000 * 1000)/
> +// ? ? ? ? ? ? nuc900_driver_clksrc_div(fbi->dev, "ext", 0x2);
> +// ? ? }
> +//
> +//}
> +
> +/*
> + * ? ? calculate divider for lcd div
> + */
> +static unsigned int nuc900fb_calc_pixclk(struct nuc900fb_info *fbi,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned long pixclk)
> +{
> + ? ? ? unsigned long clk = fbi->clk_rate;
> + ? ? ? unsigned long long div;
> +
> + ? ? ? /* pixclk is in picseconds. our clock is in Hz*/
> + ? ? ? /* div = (clk * pixclk)/10^12 */
> + ? ? ? div = (unsigned long long)clk * pixclk;
> + ? ? ? div >>= 12;
> + ? ? ? do_div(div, 625 * 625UL * 625);
> +
> + ? ? ? dprintk("pixclk %ld, divisor is %ld\n", pixclk, (long)div);
> +
> + ? ? ? return div;
> +}
> +
> +/*
> + * ? ? Check the video params of 'var'.
> + */
> +static int nuc900fb_check_var(struct fb_var_screeninfo *var,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
> + ? ? ? struct nuc900fb_display *display = NULL;
> + ? ? ? struct nuc900fb_display *default_display = mach_info->displays +
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?mach_info->default_display;
> + ? ? ? int i;
> +
> + ? ? ? dprintk("check_var(var=%p, info=%p)\n", var, info);
> +
> + ? ? ? /* validate x/y resolution */
> + ? ? ? /* choose default mode if possible */
> + ? ? ? if (var->xres == default_display->xres &&
> + ? ? ? ? ? var->yres == default_display->yres &&
> + ? ? ? ? ? var->bits_per_pixel == default_display->bpp)
> + ? ? ? ? ? ? ? display = default_display;
> + ? ? ? else
> + ? ? ? ? ? ? ? for (i = 0; i < mach_info->num_displays; i++)
> + ? ? ? ? ? ? ? ? ? ? ? if (var->xres == mach_info->displays[i].xres &&
> + ? ? ? ? ? ? ? ? ? ? ? ? ? var->yres == mach_info->displays[i].yres &&
> + ? ? ? ? ? ? ? ? ? ? ? ? ? var->bits_per_pixel == mach_info->displays[i].bpp) {
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? display = mach_info->displays + i;
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? break;
> + ? ? ? ? ? ? ? ? ? ? ? }
> +
> + ? ? ? if (display == NULL) {
> + ? ? ? ? ? ? ? dprintk("wrong resolution or depth %dx%d at %d bit per pixel\n",
> + ? ? ? ? ? ? ? ? ? ? ? var->xres, var->yres, var->bits_per_pixel);
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> +
> + ? ? ? /* it should be the same size as the display */
> + ? ? ? var->xres_virtual ? ? ? = display->xres;
> + ? ? ? var->yres_virtual ? ? ? = display->yres;
> + ? ? ? var->height ? ? ? ? ? ? = display->height;
> + ? ? ? var->width ? ? ? ? ? ? ?= display->width;
> +
> + ? ? ? /* copy lcd settings */
> + ? ? ? var->pixclock ? ? ? ? ? = display->pixclock;
> + ? ? ? var->left_margin ? ? ? ?= display->left_margin;
> + ? ? ? var->right_margin ? ? ? = display->right_margin;
> + ? ? ? var->upper_margin ? ? ? = display->upper_margin;
> + ? ? ? var->lower_margin ? ? ? = display->lower_margin;
> + ? ? ? var->vsync_len ? ? ? ? ?= display->vsync_len;
> + ? ? ? var->hsync_len ? ? ? ? ?= display->hsync_len;
> +
> + ? ? ? var->transp.offset ? ? ?= 0;
> + ? ? ? var->transp.length ? ? ?= 0;
> +
> + ? ? ? fbi->regs.lcd_dccs = display->dccs;
> + ? ? ? fbi->regs.lcd_device_ctrl = display->devctl;
> + ? ? ? fbi->regs.lcd_va_fbctrl = display->fbctrl;
> + ? ? ? fbi->regs.lcd_va_scale = display->scale;
> +
> + ? ? ? /* set R/G/B possions */
> + ? ? ? switch (var->bits_per_pixel) {
> + ? ? ? case 1:
> + ? ? ? case 2:
> + ? ? ? case 4:
> + ? ? ? case 8:
> + ? ? ? default:
> + ? ? ? ? ? ? ? var->red.offset ? ? ? ? = 0;
> + ? ? ? ? ? ? ? var->red.length ? ? ? ? = var->bits_per_pixel;
> + ? ? ? ? ? ? ? var->green ? ? ? ? ? ? ?= var->red;
> + ? ? ? ? ? ? ? var->blue ? ? ? ? ? ? ? = var->red;
> + ? ? ? ? ? ? ? break;
> + ? ? ? case 12:
> + ? ? ? ? ? ? ? var->red.length ? ? ? ? = 4;
> + ? ? ? ? ? ? ? var->green.length ? ? ? = 4;
> + ? ? ? ? ? ? ? var->blue.length ? ? ? ?= 4;
> + ? ? ? ? ? ? ? var->red.offset ? ? ? ? = 8;
> + ? ? ? ? ? ? ? var->green.offset ? ? ? = 4;
> + ? ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
> + ? ? ? ? ? ? ? break;
> + ? ? ? case 16:
> + ? ? ? ? ? ? ? var->red.length ? ? ? ? = 5;
> + ? ? ? ? ? ? ? var->green.length ? ? ? = 6;
> + ? ? ? ? ? ? ? var->blue.length ? ? ? ?= 5;
> + ? ? ? ? ? ? ? var->red.offset ? ? ? ? = 11;
> + ? ? ? ? ? ? ? var->green.offset ? ? ? = 5;
> + ? ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
> + ? ? ? ? ? ? ? break;
> + ? ? ? case 18:
> + ? ? ? ? ? ? ? var->red.length ? ? ? ? = 6;
> + ? ? ? ? ? ? ? var->green.length ? ? ? = 6;
> + ? ? ? ? ? ? ? var->blue.length ? ? ? ?= 6;
> + ? ? ? ? ? ? ? var->red.offset ? ? ? ? = 12;
> + ? ? ? ? ? ? ? var->green.offset ? ? ? = 6;
> + ? ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
> + ? ? ? ? ? ? ? break;
> + ? ? ? case 32:
> + ? ? ? ? ? ? ? var->red.length ? ? ? ? = 8;
> + ? ? ? ? ? ? ? var->green.length ? ? ? = 8;
> + ? ? ? ? ? ? ? var->blue.length ? ? ? ?= 8;
> + ? ? ? ? ? ? ? var->red.offset ? ? ? ? = 16;
> + ? ? ? ? ? ? ? var->green.offset ? ? ? = 8;
> + ? ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
> + ? ? ? ? ? ? ? break;
> + ? ? ? }
> +
> + ? ? ? return 0;
> +}
> +
> +/*
> + * ? ? Calculate lcd register values from var setting & save into hw
> + */
> +static void nuc900fb_calculate_lcd_regs(const struct fb_info *info,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct nuc900fb_hw *regs)
> +{
> + ? ? ? const struct fb_var_screeninfo *var = &info->var;
> + ? ? ? int vtt = var->height + var->upper_margin + var->lower_margin;
> + ? ? ? int htt = var->width + var->left_margin + var->right_margin;
> + ? ? ? int hsync = var->width + var->right_margin;
> + ? ? ? int vsync = var->height + var->lower_margin;
> + ? ? ? regs->lcd_crtc_size = LCM_CRTC_SIZE_VTTVAL(vtt) |
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_SIZE_HTTVAL(htt);
> + ? ? ? regs->lcd_crtc_dend = LCM_CRTC_DEND_VDENDVAL(var->height) |
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_DEND_HDENDVAL(var->width);
> + ? ? ? regs->lcd_crtc_hr = LCM_CRTC_HR_EVAL(var->width + 5) |
> + ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_HR_SVAL(var->width + 1);
> + ? ? ? regs->lcd_crtc_hsync = LCM_CRTC_HSYNC_EVAL(hsync + var->hsync_len) |
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?LCM_CRTC_HSYNC_SVAL(hsync);
> + ? ? ? regs->lcd_crtc_vr = LCM_CRTC_VR_EVAL(vsync + var->vsync_len) |
> + ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_VR_SVAL(vsync);
> +
> +}
> +
> +/*
> + * ? ? Activate (set) the controller from the given framebuffer
> + * ? ? information
> + */
> +static void nuc900fb_activate_var(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? void __iomem *regs = fbi->io;
> + ? ? ? struct fb_var_screeninfo *var = &info->var;
> + ? ? ? int clkdiv;
> +
> + ? ? ? clkdiv = nuc900fb_calc_pixclk(fbi, var->pixclock) - 1;
> + ? ? ? if (clkdiv < 0)
> + ? ? ? ? ? ? ? clkdiv = 0;
> +
> + ? ? ? nuc900fb_calculate_lcd_regs(info, &fbi->regs);
> +
> + ? ? ? /* set the new lcd registers*/
> +
> + ? ? ? dprintk("new lcd register set:\n");
> + ? ? ? dprintk("dccs ? ? ? ? ? = 0x%08x\n", fbi->regs.lcd_dccs);
> + ? ? ? dprintk("dev_ctl ? ? ? ?= 0x%08x\n", fbi->regs.lcd_device_ctrl);
> + ? ? ? dprintk("crtc_size ? ? ?= 0x%08x\n", fbi->regs.lcd_crtc_size);
> + ? ? ? dprintk("crtc_dend ? ? ?= 0x%08x\n", fbi->regs.lcd_crtc_dend);
> + ? ? ? dprintk("crtc_hr ? ? ? ?= 0x%08x\n", fbi->regs.lcd_crtc_hr);
> + ? ? ? dprintk("crtc_hsync ? ? = 0x%08x\n", fbi->regs.lcd_crtc_hsync);
> + ? ? ? dprintk("crtc_vr ? ? ? ?= 0x%08x\n", fbi->regs.lcd_crtc_vr);
> +
> + ? ? ? writel(fbi->regs.lcd_device_ctrl, regs + REG_LCM_DEV_CTRL);
> + ? ? ? writel(fbi->regs.lcd_crtc_size, regs + REG_LCM_CRTC_SIZE);
> + ? ? ? writel(fbi->regs.lcd_crtc_dend, regs + REG_LCM_CRTC_DEND);
> + ? ? ? writel(fbi->regs.lcd_crtc_hr, regs + REG_LCM_CRTC_HR);
> + ? ? ? writel(fbi->regs.lcd_crtc_hsync, regs + REG_LCM_CRTC_HSYNC);
> + ? ? ? writel(fbi->regs.lcd_crtc_vr, regs + REG_LCM_CRTC_VR);
> +
> + ? ? ? /* set lcd address pointers */
> + ? ? ? nuc900fb_set_lcdaddr(info);
> +
> + ? ? ? writel(fbi->regs.lcd_dccs, regs + REG_LCM_DCCS);
> +}
> +
> +/*
> + * ? ? ?Alters the hardware state.
> + *
> + */
> +static int nuc900fb_set_par(struct fb_info *info)
> +{
> + ? ? ? struct fb_var_screeninfo *var = &info->var;
> +
> + ? ? ? dprintk("nuc900fb_set_par\n");
> +
> + ? ? ? switch (var->bits_per_pixel) {
> + ? ? ? case 32:
> + ? ? ? case 24:
> + ? ? ? case 18:
> + ? ? ? case 16:
> + ? ? ? case 12:
> + ? ? ? ? ? ? ? info->fix.visual = FB_VISUAL_TRUECOLOR;
> + ? ? ? ? ? ? ? break;
> + ? ? ? case 1:
> + ? ? ? ? ? ? ? info->fix.visual = FB_VISUAL_MONO01;
> + ? ? ? ? ? ? ? break;
> + ? ? ? default:
> + ? ? ? ? ? ? ? info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
> + ? ? ? ? ? ? ? break;
> + ? ? ? }
> +
> + ? ? ? info->fix.line_length = (var->xres_virtual * var->bits_per_pixel) / 8;
> +
> + ? ? ? /* activate this new configuration */
> + ? ? ? nuc900fb_activate_var(info);
> + ? ? ? return 0;
> +}
> +
> +static inline unsigned int chan_to_field(unsigned int chan,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct fb_bitfield *bf)
> +{
> + ? ? ? chan &= 0xffff;
> + ? ? ? chan >>= 16 - bf->length;
> + ? ? ? return chan << bf->offset;
> +}
> +
> +static int nuc900fb_setcolreg(unsigned regno,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned red, unsigned green, unsigned blue,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned transp, struct fb_info *info)
> +{
> + ? ? ? unsigned int val;
> +
> + ? ? ? switch (info->fix.visual) {
> + ? ? ? case FB_VISUAL_TRUECOLOR:
> + ? ? ? ? ? ? ? /* true-colour, use pseuo-palette */
> + ? ? ? ? ? ? ? if (regno < 16) {
> + ? ? ? ? ? ? ? ? ? ? ? u32 *pal = info->pseudo_palette;
> +
> + ? ? ? ? ? ? ? ? ? ? ? val ?= chan_to_field(red, &info->var.red);
> + ? ? ? ? ? ? ? ? ? ? ? val |= chan_to_field(green, &info->var.green);
> + ? ? ? ? ? ? ? ? ? ? ? val |= chan_to_field(blue, &info->var.blue);
> + ? ? ? ? ? ? ? ? ? ? ? pal[regno] = val;
> + ? ? ? ? ? ? ? }
> + ? ? ? ? ? ? ? break;
> +
> + ? ? ? default:
> + ? ? ? ? ? ? ? return 1; ? /* unknown type */
> + ? ? ? }
> + ? ? ? return 0;
> +}
> +
> +/**
> + * ? ? ?nuc900fb_blank
> + *
> + */
> +static int nuc900fb_blank(int blank_mode, struct fb_info *info)
> +{
> +
> + ? ? ? return 0;
> +}
> +
> +static int nuc900fb_debug_show(struct device *dev,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct device_attribute *attr, char *buf)
> +{
> + ? ? ? return snprintf(buf, PAGE_SIZE, "%s\n", debug ? "on" : "off");
> +}
> +
> +static int nuc900fb_debug_store(struct device *dev,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct device_attribute *attr,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? const char *buf, size_t len)
> +{
> + ? ? ? if (len < 1)
> + ? ? ? ? ? ? ? return -EINVAL;
> +
> + ? ? ? if (strnicmp(buf, "on", 2) == 0 ||
> + ? ? ? ? ? strnicmp(buf, "1", 1) == 0) {
> + ? ? ? ? ? ? ? debug = 1;
> + ? ? ? } else if (strnicmp(buf, "off", 3) == 0 ||
> + ? ? ? ? ? ? ? ? ?strnicmp(buf, "0", 1) == 0) {
> + ? ? ? ? ? ? ? debug = 0;
> +
> + ? ? ? } else {
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> +
> + ? ? ? return len;
> +}
> +
> +static DEVICE_ATTR(debug, 0666, nuc900fb_debug_show, nuc900fb_debug_store);
> +
> +static struct fb_ops nuc900fb_ops = {
> + ? ? ? .owner ? ? ? ? ? ? ? ? ?= THIS_MODULE,
> + ? ? ? .fb_check_var ? ? ? ? ? = nuc900fb_check_var,
> + ? ? ? .fb_set_par ? ? ? ? ? ? = nuc900fb_set_par,
> + ? ? ? .fb_blank ? ? ? ? ? ? ? = nuc900fb_blank,
> + ? ? ? .fb_setcolreg ? ? ? ? ? = nuc900fb_setcolreg,
> + ? ? ? .fb_fillrect ? ? ? ? ? ?= cfb_fillrect,
> + ? ? ? .fb_copyarea ? ? ? ? ? ?= cfb_copyarea,
> + ? ? ? .fb_imageblit ? ? ? ? ? = cfb_imageblit,
> +};
> +
> +
> +static inline void modify_gpio(void __iomem *reg,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned long set, unsigned long mask)
> +{
> + ? ? ? unsigned long tmp;
> + ? ? ? tmp = readl(reg) & ~mask;
> + ? ? ? writel(tmp | set, reg);
> +}
> +
> +/*
> + * Initialise LCD-related registers
> + */
> +static int nuc900fb_init_registers(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
> + ? ? ? void __iomem *regs = fbi->io;
> +
> + ? ? ? /*reset the display engine*/
> + ? ? ? writel(0, regs + REG_LCM_DCCS);
> + ? ? ? writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_ENG_RST,
> + ? ? ? ? ? ? ?regs + REG_LCM_DCCS);
> + ? ? ? ndelay(100);
> + ? ? ? writel(readl(regs + REG_LCM_DCCS) & (~LCM_DCCS_ENG_RST),
> + ? ? ? ? ? ? ?regs + REG_LCM_DCCS);
> + ? ? ? ndelay(100);
> +
> + ? ? ? writel(0, regs + REG_LCM_DEV_CTRL);
> +
> + ? ? ? /* config gpio output */
> + ? ? ? modify_gpio(W90X900_VA_GPIO + 0x54, mach_info->gpio_dir,
> + ? ? ? ? ? ? ? ? ? mach_info->gpio_dir_mask);
> + ? ? ? modify_gpio(W90X900_VA_GPIO + 0x58, mach_info->gpio_data,
> + ? ? ? ? ? ? ? ? ? mach_info->gpio_data_mask);
> +
> + ? ? ? return 0;
> +}
> +
> +
> +/*
> + * ? ?Alloc the SDRAM region of NUC900 for the frame buffer.
> + * ? ?The buffer should be a non-cached, non-buffered, memory region
> + * ? ?to allow palette and pixel writes without flushing the cache.
> + */
> +static int __init nuc900fb_map_video_memory(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? dma_addr_t map_dma;
> + ? ? ? unsigned long map_size = PAGE_ALIGN(info->fix.smem_len);
> +
> + ? ? ? dprintk("nuc900fb_map_video_memory(fbi=%p) map_size %lu\n",
> + ? ? ? ? ? ? ? fbi, map_size);
> +
> + ? ? ? info->screen_base = dma_alloc_writecombine(fbi->dev, map_size,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? &map_dma, GFP_KERNEL);
> +
> + ? ? ? if (info->screen_base != NULL) {
> + ? ? ? ? ? ? ? dprintk("nuc900fb_map_video_memory: clear %p:%08lx\n",
> + ? ? ? ? ? ? ? ? ? ? ? info->screen_base, map_size);
> + ? ? ? ? ? ? ? memset(info->screen_base, 0x00, map_size);
> +
> + ? ? ? ? ? ? ? info->fix.smem_start = map_dma;
> + ? ? ? ? ? ? ? dprintk("nuc900fb_map_video_memory: "
> + ? ? ? ? ? ? ? ? ? ? ? "dma=%08lx cpu=%p size=%08lx\n",
> + ? ? ? ? ? ? ? ? ? ? ? info->fix.smem_start, info->screen_base, map_size);
> + ? ? ? }
> + ? ? ? return (info->screen_base) ? 0 : -ENOMEM;
> +}
> +
> +static inline void nuc900fb_unmap_video_memory(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? dma_free_writecombine(fbi->dev, PAGE_ALIGN(info->fix.smem_len),
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? info->screen_base, info->fix.smem_start);
> +}
> +
> +static irqreturn_t nuc900fb_irqhandler(int irq, void *dev_id)
> +{
> + ? ? ? struct nuc900fb_info *fbi = dev_id;
> + ? ? ? void __iomem *regs = fbi->io;
> + ? ? ? void __iomem *irq_base = fbi->irq_base;
> + ? ? ? unsigned long lcdirq = readl(regs + REG_LCM_INT_CS);
> +
> + ? ? ? if (lcdirq & LCM_INT_CS_DISP_F_STATUS) {
> + ? ? ? ? ? ? ? writel(readl(irq_base) | 1<<30, irq_base);
> +
> + ? ? ? ? ? ? ? /* wait VA_EN low */
> + ? ? ? ? ? ? ? if ((readl(regs + REG_LCM_DCCS) &
> + ? ? ? ? ? ? ? ? ? LCM_DCCS_SINGLE) == LCM_DCCS_SINGLE)
> + ? ? ? ? ? ? ? ? ? ? ? while ((readl(regs + REG_LCM_DCCS) &
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?LCM_DCCS_VA_EN) == LCM_DCCS_VA_EN)
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ;
> + ? ? ? ? ? ? ? /* display_out-enable */
> + ? ? ? ? ? ? ? writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_DISP_OUT_EN,
> + ? ? ? ? ? ? ? ? ? ? ? regs + REG_LCM_DCCS);
> + ? ? ? ? ? ? ? /* va-enable*/
> + ? ? ? ? ? ? ? writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_VA_EN,
> + ? ? ? ? ? ? ? ? ? ? ? regs + REG_LCM_DCCS);
> + ? ? ? } else if (lcdirq & LCM_INT_CS_UNDERRUN_INT) {
> + ? ? ? ? ? ? ? writel(readl(irq_base) | LCM_INT_CS_UNDERRUN_INT, irq_base);
> + ? ? ? } else if (lcdirq & LCM_INT_CS_BUS_ERROR_INT) {
> + ? ? ? ? ? ? ? writel(readl(irq_base) | LCM_INT_CS_BUS_ERROR_INT, irq_base);
> + ? ? ? }
> +
> + ? ? ? return IRQ_HANDLED;
> +}
> +
> +#ifdef CONFIG_CPU_FREQ
> +
> +static int nuc900fb_cpufreq_transition(struct notifier_block *nb,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned long val, void *data)
> +{
> + ? ? ? struct nuc900fb_info *info;
> + ? ? ? struct fb_info *fbinfo;
> + ? ? ? long delta_f;
> + ? ? ? info = container_of(nb, struct nuc900fb_info, freq_transition);
> + ? ? ? fbinfo = platform_get_drvdata(to_platform_device(info->dev));
> +
> + ? ? ? delta_f = info->clk_rate - clk_get_rate(info->clk);
> +
> + ? ? ? if ((val == CPUFREQ_POSTCHANGE && delta_f > 0) ||
> + ? ? ? ? ?(val == CPUFREQ_PRECHANGE && delta_f < 0)) {
> + ? ? ? ? ? ? ? info->clk_rate = clk_get_rate(info->clk);
> + ? ? ? ? ? ? ? nuc900fb_activate_var(fbinfo);
> + ? ? ? }
> +
> + ? ? ? return 0;
> +}
> +
> +static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
> +{
> + ? ? ? fbi->freq_transition.notifier_call = nuc900fb_cpufreq_transition;
> + ? ? ? return cpufreq_register_notifier(&fbi->freq_transition,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CPUFREQ_TRANSITION_NOTIFIER);
> +}
> +
> +static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *fbi)
> +{
> + ? ? ? cpufreq_unregister_notifier(&fbi->freq_transition,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CPUFREQ_TRANSITION_NOTIFIER);
> +}
> +#else
> +static inline int nuc900fb_cpufreq_transition(struct notifier_block *nb,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned long val, void *data)
> +{
> + ? ? ? return 0;
> +}
> +
> +static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
> +{
> + ? ? ? return 0;
> +}
> +
> +static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *info)
> +{
> +}
> +#endif
> +
> +static char driver_name[] = "nuc900fb";
> +
> +static int __init nuc900fb_probe(struct platform_device *pdev)
> +{
> + ? ? ? struct nuc900fb_info *fbi;
> + ? ? ? struct nuc900fb_display *display;
> + ? ? ? struct fb_info ? ? *fbinfo;
> + ? ? ? struct nuc900fb_mach_info *mach_info;
> + ? ? ? struct resource *res;
> + ? ? ? int ret;
> + ? ? ? int irq;
> + ? ? ? int i;
> + ? ? ? int size;
> +
> + ? ? ? dprintk("devinit\n");
> + ? ? ? mach_info = pdev->dev.platform_data;
> + ? ? ? if (mach_info == NULL) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev,
> + ? ? ? ? ? ? ? ? ? ? ? "no platform data for lcd, cannot attach\n");
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> +
> + ? ? ? if (mach_info->default_display > mach_info->num_displays) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev,
> + ? ? ? ? ? ? ? ? ? ? ? "default display No. is %d but only %d displays \n",
> + ? ? ? ? ? ? ? ? ? ? ? mach_info->default_display, mach_info->num_displays);
> + ? ? ? ? ? ? ? return -EINVAL;
> + ? ? ? }
> +
> +
> + ? ? ? display = mach_info->displays + mach_info->default_display;
> +
> + ? ? ? irq = platform_get_irq(pdev, 0);
> + ? ? ? if (irq < 0) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev, "no irq for device\n");
> + ? ? ? ? ? ? ? return -ENOENT;
> + ? ? ? }
> +
> + ? ? ? fbinfo = framebuffer_alloc(sizeof(struct nuc900fb_info), &pdev->dev);
> + ? ? ? if (!fbinfo)
> + ? ? ? ? ? ? ? return -ENOMEM;
> +
> + ? ? ? platform_set_drvdata(pdev, fbinfo);
> +
> + ? ? ? fbi = fbinfo->par;
> + ? ? ? fbi->dev = &pdev->dev;
> +
> +#ifdef CONFIG_CPU_NUC950
> + ? ? ? fbi->drv_type = LCDDRV_NUC950;
> +#endif
> +
> + ? ? ? res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
> + ? ? ? size = (res->end - res->start) + 1;
> + ? ? ? fbi->mem = request_mem_region(res->start, size, pdev->name);
> + ? ? ? if (fbi->mem == NULL) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev, "failed to alloc memory region\n");
> + ? ? ? ? ? ? ? ret = -ENOENT;
> + ? ? ? ? ? ? ? goto free_fb;
> + ? ? ? }
> +
> + ? ? ? fbi->io = ioremap(res->start, size);
> + ? ? ? if (fbi->io == NULL) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev, "ioremap() of lcd registers failed\n");
> + ? ? ? ? ? ? ? ret = -ENXIO;
> + ? ? ? ? ? ? ? goto release_mem_region;
> + ? ? ? }
> +
> + ? ? ? fbi->irq_base = fbi->io + REG_LCM_INT_CS;
> +
> +
> + ? ? ? /* Stop the LCD */
> + ? ? ? writel(0, fbi->io + REG_LCM_DCCS);
> +
> + ? ? ? /* fill the fbinfo*/
> + ? ? ? strcpy(fbinfo->fix.id, driver_name);
> + ? ? ? fbinfo->fix.type ? ? ? ? ? ? ? ?= FB_TYPE_PACKED_PIXELS;
> + ? ? ? fbinfo->fix.type_aux ? ? ? ? ? ?= 0;
> + ? ? ? fbinfo->fix.xpanstep ? ? ? ? ? ?= 0;
> + ? ? ? fbinfo->fix.ypanstep ? ? ? ? ? ?= 0;
> + ? ? ? fbinfo->fix.ywrapstep ? ? ? ? ? = 0;
> + ? ? ? fbinfo->fix.accel ? ? ? ? ? ? ? = FB_ACCEL_NONE;
> + ? ? ? fbinfo->var.nonstd ? ? ? ? ? ? ?= 0;
> + ? ? ? fbinfo->var.activate ? ? ? ? ? ?= FB_ACTIVATE_NOW;
> + ? ? ? fbinfo->var.accel_flags ? ? ? ? = 0;
> + ? ? ? fbinfo->var.vmode ? ? ? ? ? ? ? = FB_VMODE_NONINTERLACED;
> + ? ? ? fbinfo->fbops ? ? ? ? ? ? ? ? ? = &nuc900fb_ops;
> + ? ? ? fbinfo->flags ? ? ? ? ? ? ? ? ? = FBINFO_FLAG_DEFAULT;
> + ? ? ? fbinfo->pseudo_palette ? ? ? ? ?= &fbi->pseudo_pal;
> +
> + ? ? ? ret = request_irq(irq, nuc900fb_irqhandler, IRQF_DISABLED,
> + ? ? ? ? ? ? ? ? ? ? ? ? pdev->name, fbinfo);
> + ? ? ? if (ret) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev, "cannot register irq handler %d -err %d\n",
> + ? ? ? ? ? ? ? ? ? ? ? irq, ret);
> + ? ? ? ? ? ? ? ret = -EBUSY;
> + ? ? ? ? ? ? ? goto release_regs;
> + ? ? ? }
> +
> + ? ? ? nuc900_driver_clksrc_div(&pdev->dev, "ext", 0x2);
> +
> + ? ? ? fbi->clk = clk_get(&pdev->dev, NULL);
> + ? ? ? if (!fbi->clk || IS_ERR(fbi->clk)) {
> + ? ? ? ? ? ? ? printk(KERN_ERR "nuc900-lcd:failed to get lcd clock source\n");
> + ? ? ? ? ? ? ? ret = -ENOENT;
> + ? ? ? ? ? ? ? goto release_irq;
> + ? ? ? }
> +
> + ? ? ? clk_enable(fbi->clk);
> + ? ? ? dprintk("got and enabled clock\n");
> +
> + ? ? ? fbi->clk_rate = clk_get_rate(fbi->clk);
> +
> + ? ? ? /* calutate the video buffer size */
> + ? ? ? for (i = 0; i < mach_info->num_displays; i++) {
> + ? ? ? ? ? ? ? unsigned long smem_len = mach_info->displays[i].xres;
> + ? ? ? ? ? ? ? smem_len *= mach_info->displays[i].yres;
> + ? ? ? ? ? ? ? smem_len *= mach_info->displays[i].bpp;
> + ? ? ? ? ? ? ? smem_len >>= 3;
> + ? ? ? ? ? ? ? if (fbinfo->fix.smem_len < smem_len)
> + ? ? ? ? ? ? ? ? ? ? ? fbinfo->fix.smem_len = smem_len;
> + ? ? ? }
> +
> + ? ? ? /* Initialize Video Memory */
> + ? ? ? ret = nuc900fb_map_video_memory(fbinfo);
> + ? ? ? if (ret) {
> + ? ? ? ? ? ? ? printk(KERN_ERR "Failed to allocate video RAM: %x\n", ret);
> + ? ? ? ? ? ? ? goto release_clock;
> + ? ? ? }
> +
> + ? ? ? dprintk("got video memory\n");
> +
> + ? ? ? fbinfo->var.xres = display->xres;
> + ? ? ? fbinfo->var.yres = display->yres;
> + ? ? ? fbinfo->var.bits_per_pixel = display->bpp;
> +
> + ? ? ? nuc900fb_init_registers(fbinfo);
> +
> + ? ? ? nuc900fb_check_var(&fbinfo->var, fbinfo);
> +
> + ? ? ? ret = nuc900fb_cpufreq_register(fbi);
> + ? ? ? if (ret < 0) {
> + ? ? ? ? ? ? ? dev_err(&pdev->dev, "Failed to register cpufreq\n");
> + ? ? ? ? ? ? ? goto free_video_memory;
> + ? ? ? }
> +
> + ? ? ? ret = register_framebuffer(fbinfo);
> + ? ? ? if (ret) {
> + ? ? ? ? ? ? ? printk(KERN_ERR "failed to register framebuffer device: %d\n",
> + ? ? ? ? ? ? ? ? ? ? ? ret);
> + ? ? ? ? ? ? ? goto free_cpufreq;
> + ? ? ? }
> +
> + ? ? ? /* create device files */
> + ? ? ? ret = device_create_file(&pdev->dev, &dev_attr_debug);
> + ? ? ? if (ret)
> + ? ? ? ? ? ? ? printk(KERN_ERR "failed to add debug attribute\n");
> +
> +
> + ? ? ? printk(KERN_INFO "fb%d: %s frame buffer device\n",
> + ? ? ? ? ? ? ? fbinfo->node, fbinfo->fix.id);
> +
> + ? ? ? return 0;
> +
> +free_cpufreq:
> + ? ? ? nuc900fb_cpufreq_deregister(fbi);
> +free_video_memory:
> + ? ? ? nuc900fb_unmap_video_memory(fbinfo);
> +release_clock:
> + ? ? ? clk_disable(fbi->clk);
> + ? ? ? clk_put(fbi->clk);
> +release_irq:
> + ? ? ? free_irq(irq, fbi);
> +release_regs:
> + ? ? ? iounmap(fbi->io);
> +release_mem_region:
> + ? ? ? release_mem_region((unsigned long)fbi->mem, size);
> +free_fb:
> + ? ? ? framebuffer_release(fbinfo);
> + ? ? ? return ret;
> +}
> +
> +/*
> + * shutdown the lcd controller
> + */
> +static void nuc900fb_stop_lcd(struct fb_info *info)
> +{
> + ? ? ? struct nuc900fb_info *fbi = info->par;
> + ? ? ? void __iomem *regs = fbi->io;
> + ? ? ? unsigned long flags;
> +
> + ? ? ? local_irq_save(flags);
> + ? ? ? writel((~LCM_DCCS_DISP_INT_EN) | (~LCM_DCCS_VA_EN) | (~LCM_DCCS_OSD_EN),
> + ? ? ? ? ? ? ? regs + REG_LCM_DCCS);
> + ? ? ? local_irq_restore(flags);
> +}
> +
> +/*
> + * ?Cleanup
> + */
> +static int nuc900fb_remove(struct platform_device *pdev)
> +{
> + ? ? ? struct fb_info *fbinfo = platform_get_drvdata(pdev);
> + ? ? ? struct nuc900fb_info *fbi = fbinfo->par;
> + ? ? ? int irq;
> +
> + ? ? ? nuc900fb_stop_lcd(fbinfo);
> + ? ? ? msleep(1);
> +
> + ? ? ? nuc900fb_unmap_video_memory(fbinfo);
> +
> + ? ? ? iounmap(fbi->io);
> +
> + ? ? ? irq = platform_get_irq(pdev, 0);
> + ? ? ? free_irq(irq, fbi);
> +
> + ? ? ? release_resource(fbi->mem);
> + ? ? ? kfree(fbi->mem);
> +
> + ? ? ? platform_set_drvdata(pdev, NULL);
> + ? ? ? framebuffer_release(fbinfo);
> +
> + ? ? ? return 0;
> +}
> +
> +#ifdef CONFIG_PM
> +
> +/*
> + * ? ? suspend and resume support for the lcd controller
> + */
> +
> +static int nuc900fb_suspend(struct platform_device *dev, pm_message_t state)
> +{
> + ? ? ? struct fb_info ? ? *fbinfo = platform_get_drvdata(dev);
> + ? ? ? struct nuc900fb_info *info = fbinfo->par;
> +
> + ? ? ? nuc900fb_stop_lcd();
> + ? ? ? msleep(1);
> + ? ? ? clk_disable(info->clk);
> + ? ? ? return 0;
> +}
> +
> +static int nuc900fb_resume(struct platform_device *dev)
> +{
> + ? ? ? struct fb_info ? ? *fbinfo = platform_get_drvdata(dev);
> + ? ? ? struct nuc900fb_info *fbi = fbinfo->par;
> +
> + ? ? ? dprintk("nuc900fb resume\n");
> +
> + ? ? ? clk_enable(fbi->clk);
> + ? ? ? msleep(1);
> +
> + ? ? ? nuc900fb_init_registers(fbinfo);
> + ? ? ? nuc900fb_activate_var(bfinfo);
> +
> + ? ? ? return 0;
> +}
> +
> +#else
> +#define nuc900fb_suspend NULL
> +#define nuc900fb_resume ?NULL
> +#endif
> +
> +static struct platform_driver nuc900fb_driver = {
> + ? ? ? .probe ? ? ? ? ?= nuc900fb_probe,
> + ? ? ? .remove ? ? ? ? = nuc900fb_remove,
> + ? ? ? .suspend ? ? ? ?= nuc900fb_suspend,
> + ? ? ? .resume ? ? ? ? = nuc900fb_resume,
> + ? ? ? .driver ? ? ? ? = {
> + ? ? ? ? ? ? ? .name ? = "nuc900-lcd",
> + ? ? ? ? ? ? ? .owner ?= THIS_MODULE,
> + ? ? ? },
> +};
> +
> +int __devinit nuc900fb_init(void)
> +{
> + ? ? ? return platform_driver_register(&nuc900fb_driver);
> +}
> +
> +static void __exit nuc900fb_cleanup(void)
> +{
> + ? ? ? platform_driver_unregister(&nuc900fb_driver);
> +}
> +
> +module_init(nuc900fb_init);
> +module_exit(nuc900fb_cleanup);
> +
> +MODULE_DESCRIPTION("Framebuffer driver for the NUC900");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/video/nuc900fb.h b/drivers/video/nuc900fb.h
> new file mode 100644
> index 0000000..6c23aa3
> --- /dev/null
> +++ b/drivers/video/nuc900fb.h
> @@ -0,0 +1,55 @@
> +/*
> + *
> + * Copyright (c) 2009 Nuvoton technology corporation
> + * All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * ? Auther:
> + * ? ? ? ?Wang Qiang(rurality.linux at gmail.com) ?2009/12/16
> + */
> +
> +#ifndef __NUC900FB_H
> +#define __NUC900FB_H
> +
> +#include <mach/map.h>
> +#include <mach/fb.h>
> +
> +enum nuc900_lcddrv_type {
> + ? ? ? LCDDRV_NUC910,
> + ? ? ? LCDDRV_NUC930,
> + ? ? ? LCDDRV_NUC932,
> + ? ? ? LCDDRV_NUC950,
> + ? ? ? LCDDRV_NUC960,
> +};
> +
> +
> +#define PALETTE_BUFFER_SIZE ? ?256
> +#define PALETTE_BUFF_CLEAR ? ? (0x80000000) /* entry is clear/invalid */
> +
> +struct nuc900fb_info {
> + ? ? ? struct device ? ? ? ? ? *dev;
> + ? ? ? struct clk ? ? ? ? ? ? ?*clk;
> +
> + ? ? ? struct resource ? ? ? ? *mem;
> + ? ? ? void __iomem ? ? ? ? ? ?*io;
> + ? ? ? void __iomem ? ? ? ? ? ?*irq_base;
> + ? ? ? int ? ? ? ? ? ? ? ? ? ? drv_type;
> + ? ? ? struct nuc900fb_hw ? ? ?regs;
> + ? ? ? unsigned long ? ? ? ? ? clk_rate;
> +
> +#ifdef CONFIG_CPU_FREQ
> + ? ? ? struct notifier_block ? freq_transition;
> +#endif
> +
> + ? ? ? /* keep these registers in case we need to re-write palette */
> + ? ? ? u32 ? ? ? ? ? ? ? ? ? ? palette_buffer[PALETTE_BUFFER_SIZE];
> + ? ? ? u32 ? ? ? ? ? ? ? ? ? ? pseudo_pal[16];
> +};
> +
> +int nuc900fb_init(void);
> +
> +#endif /* __NUC900FB_H */
> --
> 1.6.4
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH]NUC900 LCD Controller Driver
2010-01-11 8:05 [PATCH]NUC900 LCD Controller Driver Wang Qiang
2010-01-28 9:00 ` Qiang Wang
@ 2010-01-30 0:27 ` Andrew Morton
2010-01-30 0:37 ` H Hartley Sweeten
2010-02-01 13:33 ` [Linux-arm-nuc900] " Qiang Wang
1 sibling, 2 replies; 7+ messages in thread
From: Andrew Morton @ 2010-01-30 0:27 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, 11 Jan 2010 17:05:44 +0900
Wang Qiang <rurality.linux@gmail.com> wrote:
> hi, Dear Wan
>
> There is the patch of LCD controller driver for nuc900s.
> The Linux LOGO is just fine and the FB-Test application was ok, too.
>
> best regards
> wangqiang
>
>
> ...
>
> @@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
> .resource = nuc900_kpi_resource,
> };
>
> +#ifdef CONFIG_FB_NUC900
> +
> +static struct resource nuc900_lcd_resource[] = {
> + [0] = {
> + .start = W90X900_PA_LCD,
> + .end = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
> + .flags = IORESOURCE_MEM,
> + },
> + [1] = {
> + .start = IRQ_LCD,
> + .end = IRQ_LCD,
> + .flags = IORESOURCE_IRQ,
> + }
> +};
> +
> +static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
I suspect this should have type `dma_addr_t', but `struct device' uses
open-coded u64 too. Odd.
It makes no sense to initialise a u64 with an unsigned long value -
it's wrong on a 32-bit machine.
this:
static u64 nuc900_device_lcd_dmamask = -1;
will work.
> +struct platform_device nuc900_device_lcd = {
> + .name = "nuc900-lcd",
> + .id = -1,
> + .num_resources = ARRAY_SIZE(nuc900_lcd_resource),
> + .resource = nuc900_lcd_resource,
> + .dev = {
> + .dma_mask = &nuc900_device_lcd_dmamask,
> + .coherent_dma_mask = 0xffffffffUL
And this gets initialised to 0x00000000ffffffff also. Using -1 will fix.
> + }
> +};
> +
>
> ...
>
> + */
> +#include <linux/module.h>
> +#include <linux/kernel.h>
> +#include <linux/errno.h>
> +#include <linux/string.h>
> +#include <linux/mm.h>
> +#include <linux/tty.h>
> +#include <linux/slab.h>
> +#include <linux/delay.h>
> +#include <linux/fb.h>
> +#include <linux/init.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/interrupt.h>
> +#include <linux/workqueue.h>
> +#include <linux/wait.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/cpufreq.h>
> +#include <linux/io.h>
> +
> +#ifdef CONFIG_PM
Is this ifdef needed?
> +#include <linux/pm.h>
> +#endif
> +
> +#include <mach/map.h>
> +#include <mach/regs-clock.h>
> +#include <mach/regs-ldm.h>
> +#include <mach/fb.h>
> +#include <mach/clkdev.h>
> +
> +#include "nuc900fb.h"
> +
> +/* Debugging stuff */
> +#ifdef CONFIG_FB_NUC900_DEBUG
> +static int debug = 1;
> +#define dprintk(msg...) { printk(KERN_DEBUG "nuc900 lcd: " msg); }
> +#else
> +static int debug;
> +#define dprintk(msg...)
> +#endif
Would be better to use the standard pr_debug(), rather than inventing
private infrastructure. That way you get to enjoy the facilities which
lib/dynamic_debug.c offers.
> +
> +/*
> + * Initialize the nuc900 video (dual) buffer address
> + */
> +static void nuc900fb_set_lcdaddr(struct fb_info *info)
> +{
> + struct nuc900fb_info *fbi = info->par;
> + void __iomem *regs = fbi->io;
> + unsigned long vbaddr1, vbaddr2;
> + vbaddr1 = info->fix.smem_start;
It's conventional to put a blank line beterrn end-of-locals and start-of-code.
> + vbaddr2 = info->fix.smem_start;
> + vbaddr2 += info->fix.line_length * info->var.yres;
> + /*set frambuffer start phy addr*/
Like this:
/* set frambuffer start phy addr */
> + writel(vbaddr1, regs + REG_LCM_VA_BADDR0);
> + writel(vbaddr2, regs + REG_LCM_VA_BADDR1);
> +
> + writel(fbi->regs.lcd_va_fbctrl, regs + REG_LCM_VA_FBCTRL);
> + writel(fbi->regs.lcd_va_scale, regs + REG_LCM_VA_SCALE);
> +}
> +
> +//static void nuc900fb_clk_select(struct fb_info *info, unsigned long pixclk)
> +//{
> +// struct nuc900fb_info *fbi = info->par;
> +// int div;
> +// if (clk <= 15 * 1000 * 1000) {
> +// div = (15 * 1000 * 1000)/
> +// nuc900_driver_clksrc_div(fbi->dev, "ext", 0x2);
> +// }
> +//
> +//}
Please feed the patch through scrupts/checkpatch.pl.
> +/*
> + * calculate divider for lcd div
> + */
> +static unsigned int nuc900fb_calc_pixclk(struct nuc900fb_info *fbi,
> + unsigned long pixclk)
> +{
> + unsigned long clk = fbi->clk_rate;
> + unsigned long long div;
> +
> + /* pixclk is in picseconds. our clock is in Hz*/
> + /* div = (clk * pixclk)/10^12 */
> + div = (unsigned long long)clk * pixclk;
> + div >>= 12;
> + do_div(div, 625 * 625UL * 625);
> +
> + dprintk("pixclk %ld, divisor is %ld\n", pixclk, (long)div);
Perhaps use %lld and remove the cast.
> + return div;
> +}
> +
> +/*
> + * Check the video params of 'var'.
> + */
> +static int nuc900fb_check_var(struct fb_var_screeninfo *var,
> + struct fb_info *info)
> +{
> + struct nuc900fb_info *fbi = info->par;
> + struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
> + struct nuc900fb_display *display = NULL;
> + struct nuc900fb_display *default_display = mach_info->displays +
> + mach_info->default_display;
> + int i;
> +
> + dprintk("check_var(var=%p, info=%p)\n", var, info);
> +
> + /* validate x/y resolution */
> + /* choose default mode if possible */
> + if (var->xres == default_display->xres &&
> + var->yres == default_display->yres &&
> + var->bits_per_pixel == default_display->bpp)
> + display = default_display;
> + else
> + for (i = 0; i < mach_info->num_displays; i++)
> + if (var->xres == mach_info->displays[i].xres &&
> + var->yres == mach_info->displays[i].yres &&
> + var->bits_per_pixel == mach_info->displays[i].bpp) {
> + display = mach_info->displays + i;
> + break;
> + }
> +
> + if (display == NULL) {
> + dprintk("wrong resolution or depth %dx%d at %d bit per pixel\n",
> + var->xres, var->yres, var->bits_per_pixel);
Some of the printks in here really should be printks, not the
compile-time-suppressible dprintk(). Please review them all and
convert the ones which will be useful to end-users into printk().
> + return -EINVAL;
> + }
> +
> + /* it should be the same size as the display */
> + var->xres_virtual = display->xres;
> + var->yres_virtual = display->yres;
> + var->height = display->height;
> + var->width = display->width;
> +
> + /* copy lcd settings */
> + var->pixclock = display->pixclock;
> + var->left_margin = display->left_margin;
> + var->right_margin = display->right_margin;
> + var->upper_margin = display->upper_margin;
> + var->lower_margin = display->lower_margin;
> + var->vsync_len = display->vsync_len;
> + var->hsync_len = display->hsync_len;
> +
> + var->transp.offset = 0;
> + var->transp.length = 0;
> +
> + fbi->regs.lcd_dccs = display->dccs;
> + fbi->regs.lcd_device_ctrl = display->devctl;
> + fbi->regs.lcd_va_fbctrl = display->fbctrl;
> + fbi->regs.lcd_va_scale = display->scale;
> +
> + /* set R/G/B possions */
> + switch (var->bits_per_pixel) {
> + case 1:
> + case 2:
> + case 4:
> + case 8:
The above four lines are unneeded, but it's OK keeping them for
documentation purposes.
> + default:
> + var->red.offset = 0;
> + var->red.length = var->bits_per_pixel;
> + var->green = var->red;
> + var->blue = var->red;
> + break;
> + case 12:
> + var->red.length = 4;
> + var->green.length = 4;
> + var->blue.length = 4;
> + var->red.offset = 8;
> + var->green.offset = 4;
> + var->blue.offset = 0;
> + break;
> + case 16:
> + var->red.length = 5;
> + var->green.length = 6;
> + var->blue.length = 5;
> + var->red.offset = 11;
> + var->green.offset = 5;
> + var->blue.offset = 0;
> + break;
> + case 18:
> + var->red.length = 6;
> + var->green.length = 6;
> + var->blue.length = 6;
> + var->red.offset = 12;
> + var->green.offset = 6;
> + var->blue.offset = 0;
> + break;
> + case 32:
> + var->red.length = 8;
> + var->green.length = 8;
> + var->blue.length = 8;
> + var->red.offset = 16;
> + var->green.offset = 8;
> + var->blue.offset = 0;
> + break;
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * Calculate lcd register values from var setting & save into hw
> + */
> +static void nuc900fb_calculate_lcd_regs(const struct fb_info *info,
> + struct nuc900fb_hw *regs)
> +{
> + const struct fb_var_screeninfo *var = &info->var;
> + int vtt = var->height + var->upper_margin + var->lower_margin;
> + int htt = var->width + var->left_margin + var->right_margin;
> + int hsync = var->width + var->right_margin;
> + int vsync = var->height + var->lower_margin;
newline here, please.
> + regs->lcd_crtc_size = LCM_CRTC_SIZE_VTTVAL(vtt) |
> + LCM_CRTC_SIZE_HTTVAL(htt);
> + regs->lcd_crtc_dend = LCM_CRTC_DEND_VDENDVAL(var->height) |
> + LCM_CRTC_DEND_HDENDVAL(var->width);
> + regs->lcd_crtc_hr = LCM_CRTC_HR_EVAL(var->width + 5) |
> + LCM_CRTC_HR_SVAL(var->width + 1);
> + regs->lcd_crtc_hsync = LCM_CRTC_HSYNC_EVAL(hsync + var->hsync_len) |
> + LCM_CRTC_HSYNC_SVAL(hsync);
> + regs->lcd_crtc_vr = LCM_CRTC_VR_EVAL(vsync + var->vsync_len) |
> + LCM_CRTC_VR_SVAL(vsync);
> +
> +}
> +
>
> ...
>
> +static int nuc900fb_debug_store(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t len)
> +{
> + if (len < 1)
> + return -EINVAL;
> +
> + if (strnicmp(buf, "on", 2) == 0 ||
> + strnicmp(buf, "1", 1) == 0) {
> + debug = 1;
> + } else if (strnicmp(buf, "off", 3) == 0 ||
> + strnicmp(buf, "0", 1) == 0) {
> + debug = 0;
> +
> + } else {
> + return -EINVAL;
> + }
> +
> + return len;
> +}
Duplicates the above-mentioned dynamic-debug facility.
> +static DEVICE_ATTR(debug, 0666, nuc900fb_debug_show, nuc900fb_debug_store);
> +
>
> ...
>
> +static int __init nuc900fb_map_video_memory(struct fb_info *info)
> +{
> + struct nuc900fb_info *fbi = info->par;
> + dma_addr_t map_dma;
> + unsigned long map_size = PAGE_ALIGN(info->fix.smem_len);
> +
> + dprintk("nuc900fb_map_video_memory(fbi=%p) map_size %lu\n",
> + fbi, map_size);
> +
> + info->screen_base = dma_alloc_writecombine(fbi->dev, map_size,
> + &map_dma, GFP_KERNEL);
Here, do
if (!info->screen_base)
return -ENOMEM;
and the rest of the function gets neater.
> + if (info->screen_base != NULL) {
> + dprintk("nuc900fb_map_video_memory: clear %p:%08lx\n",
> + info->screen_base, map_size);
> + memset(info->screen_base, 0x00, map_size);
> +
> + info->fix.smem_start = map_dma;
> + dprintk("nuc900fb_map_video_memory: "
> + "dma=%08lx cpu=%p size=%08lx\n",
> + info->fix.smem_start, info->screen_base, map_size);
> + }
> + return (info->screen_base) ? 0 : -ENOMEM;
> +}
> +
>
> ...
>
> +static char driver_name[] = "nuc900fb";
> +
> +static int __init nuc900fb_probe(struct platform_device *pdev)
Should this be __devinit?
> +{
> + struct nuc900fb_info *fbi;
> + struct nuc900fb_display *display;
> + struct fb_info *fbinfo;
> + struct nuc900fb_mach_info *mach_info;
> + struct resource *res;
> + int ret;
> + int irq;
> + int i;
> + int size;
> +
> + dprintk("devinit\n");
> + mach_info = pdev->dev.platform_data;
> + if (mach_info == NULL) {
> + dev_err(&pdev->dev,
> + "no platform data for lcd, cannot attach\n");
> + return -EINVAL;
> + }
> +
> + if (mach_info->default_display > mach_info->num_displays) {
> + dev_err(&pdev->dev,
> + "default display No. is %d but only %d displays \n",
> + mach_info->default_display, mach_info->num_displays);
> + return -EINVAL;
> + }
> +
> +
> + display = mach_info->displays + mach_info->default_display;
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
> + dev_err(&pdev->dev, "no irq for device\n");
> + return -ENOENT;
> + }
> +
> + fbinfo = framebuffer_alloc(sizeof(struct nuc900fb_info), &pdev->dev);
> + if (!fbinfo)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, fbinfo);
> +
> + fbi = fbinfo->par;
> + fbi->dev = &pdev->dev;
> +
> +#ifdef CONFIG_CPU_NUC950
> + fbi->drv_type = LCDDRV_NUC950;
> +#endif
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +
>
> ...
>
> +static void nuc900fb_stop_lcd(struct fb_info *info)
> +{
> + struct nuc900fb_info *fbi = info->par;
> + void __iomem *regs = fbi->io;
> + unsigned long flags;
> +
> + local_irq_save(flags);
> + writel((~LCM_DCCS_DISP_INT_EN) | (~LCM_DCCS_VA_EN) | (~LCM_DCCS_OSD_EN),
> + regs + REG_LCM_DCCS);
> + local_irq_restore(flags);
> +}
The local_irq_save() is a worry. What's it doing here? It does
nothing to prevent an interrupt on another CPU!
> +/*
> + * Cleanup
> + */
> +static int nuc900fb_remove(struct platform_device *pdev)
> +{
> + struct fb_info *fbinfo = platform_get_drvdata(pdev);
> + struct nuc900fb_info *fbi = fbinfo->par;
> + int irq;
> +
> + nuc900fb_stop_lcd(fbinfo);
> + msleep(1);
> +
> + nuc900fb_unmap_video_memory(fbinfo);
> +
> + iounmap(fbi->io);
> +
> + irq = platform_get_irq(pdev, 0);
> + free_irq(irq, fbi);
> +
> + release_resource(fbi->mem);
> + kfree(fbi->mem);
> +
> + platform_set_drvdata(pdev, NULL);
> + framebuffer_release(fbinfo);
> +
> + return 0;
> +}
> +
>
> ...
>
The driver generally looks OK to me. Please cc me on any updates.
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH]NUC900 LCD Controller Driver
2010-01-30 0:27 ` Andrew Morton
@ 2010-01-30 0:37 ` H Hartley Sweeten
2010-02-01 13:35 ` [Linux-arm-nuc900] " Qiang Wang
2010-02-01 13:33 ` [Linux-arm-nuc900] " Qiang Wang
1 sibling, 1 reply; 7+ messages in thread
From: H Hartley Sweeten @ 2010-01-30 0:37 UTC (permalink / raw)
To: linux-arm-kernel
On Friday, January 29, 2010 5:28 PM, Andrew Morton wrote:
>
> On Mon, 11 Jan 2010 17:05:44 +0900
> Wang Qiang <rurality.linux@gmail.com> wrote:
>
>> hi, Dear Wan
>>
>> There is the patch of LCD controller driver for nuc900s.
>> The Linux LOGO is just fine and the FB-Test application was ok, too.
>>
>> best regards
>> wangqiang
>>
>>
>> ...
>>
>> @@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
>> .resource = nuc900_kpi_resource,
>> };
>>
>> +#ifdef CONFIG_FB_NUC900
>> +
>> +static struct resource nuc900_lcd_resource[] = {
>> + [0] = {
>> + .start = W90X900_PA_LCD,
>> + .end = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
>> + .flags = IORESOURCE_MEM,
>> + },
>> + [1] = {
>> + .start = IRQ_LCD,
>> + .end = IRQ_LCD,
>> + .flags = IORESOURCE_IRQ,
>> + }
>> +};
>> +
>> +static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
>
> I suspect this should have type `dma_addr_t', but `struct device' uses
> open-coded u64 too. Odd.
>
> It makes no sense to initialise a u64 with an unsigned long value -
> it's wrong on a 32-bit machine.
>
> this:
>
> static u64 nuc900_device_lcd_dmamask = -1;
>
> will work.
>
>> +struct platform_device nuc900_device_lcd = {
>> + .name = "nuc900-lcd",
>> + .id = -1,
>> + .num_resources = ARRAY_SIZE(nuc900_lcd_resource),
>> + .resource = nuc900_lcd_resource,
>> + .dev = {
>> + .dma_mask = &nuc900_device_lcd_dmamask,
>> + .coherent_dma_mask = 0xffffffffUL
>
> And this gets initialised to 0x00000000ffffffff also. Using -1 will fix.
>
Wouldn't this also work?
.dev = {
.dma_mask = &nuc900_device_lcd.dev.coherent_dma_mask,
.coherent_dma_mask = DMA_BIT_MASK(32),
},
Then you could just get rid of nuc900_device_lcd_dmamask.
Regards,
Hartley
^ permalink raw reply [flat|nested] 7+ messages in thread
* [Linux-arm-nuc900] Re: [PATCH]NUC900 LCD Controller Driver
2010-01-30 0:27 ` Andrew Morton
2010-01-30 0:37 ` H Hartley Sweeten
@ 2010-02-01 13:33 ` Qiang Wang
1 sibling, 0 replies; 7+ messages in thread
From: Qiang Wang @ 2010-02-01 13:33 UTC (permalink / raw)
To: linux-arm-kernel
? 2010?1?30? ??8:27?Andrew Morton <akpm@linux-foundation.org> ???
> On Mon, 11 Jan 2010 17:05:44 +0900
> Wang Qiang <rurality.linux@gmail.com> wrote:
>
>> hi, Dear Wan
>>
>> There is the patch of LCD controller driver for nuc900s.
>> The Linux LOGO is just fine and the FB-Test application was ok, too.
>>
>> best regards
>> wangqiang
>>
>>
>> ...
>>
>> @@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
>> ? ? ? .resource ? ? ? = nuc900_kpi_resource,
>> ?};
>>
>> +#ifdef CONFIG_FB_NUC900
>> +
>> +static struct resource nuc900_lcd_resource[] = {
>> + ? ? [0] = {
>> + ? ? ? ? ? ? .start = W90X900_PA_LCD,
>> + ? ? ? ? ? ? .end ? = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
>> + ? ? ? ? ? ? .flags = IORESOURCE_MEM,
>> + ? ? },
>> + ? ? [1] = {
>> + ? ? ? ? ? ? .start = IRQ_LCD,
>> + ? ? ? ? ? ? .end ? = IRQ_LCD,
>> + ? ? ? ? ? ? .flags = IORESOURCE_IRQ,
>> + ? ? }
>> +};
>> +
>> +static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
>
> I suspect this should have type `dma_addr_t', but `struct device' uses
> open-coded u64 too. ?Odd.
>
> It makes no sense to initialise a u64 with an unsigned long value -
> it's wrong on a 32-bit machine.
>
> this:
>
> ? ? ? ?static u64 nuc900_device_lcd_dmamask = -1;
>
> will work.
>
>> +struct platform_device nuc900_device_lcd = {
>> + ? ? .name ? ? ? ? ? ? = "nuc900-lcd",
>> + ? ? .id ? ? ? ? ? ? ? = -1,
>> + ? ? .num_resources ? ?= ARRAY_SIZE(nuc900_lcd_resource),
>> + ? ? .resource ? ? ? ? = nuc900_lcd_resource,
>> + ? ? .dev ? ? ? ? ? ? ?= {
>> + ? ? ? ? ? ? .dma_mask ? ? ? ? ? ? ? = &nuc900_device_lcd_dmamask,
>> + ? ? ? ? ? ? .coherent_dma_mask ? ? ?= 0xffffffffUL
>
> And this gets initialised to 0x00000000ffffffff also. ?Using -1 will fix.
>
>> + ? ? }
>> +};
>> +
>>
>> ...
>>
>> + */
>> +#include <linux/module.h>
>> +#include <linux/kernel.h>
>> +#include <linux/errno.h>
>> +#include <linux/string.h>
>> +#include <linux/mm.h>
>> +#include <linux/tty.h>
>> +#include <linux/slab.h>
>> +#include <linux/delay.h>
>> +#include <linux/fb.h>
>> +#include <linux/init.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/workqueue.h>
>> +#include <linux/wait.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/clk.h>
>> +#include <linux/cpufreq.h>
>> +#include <linux/io.h>
>> +
>> +#ifdef CONFIG_PM
>
> Is this ifdef needed?
>
>> +#include <linux/pm.h>
>> +#endif
>> +
>> +#include <mach/map.h>
>> +#include <mach/regs-clock.h>
>> +#include <mach/regs-ldm.h>
>> +#include <mach/fb.h>
>> +#include <mach/clkdev.h>
>> +
>> +#include "nuc900fb.h"
>> +
>> +/* Debugging stuff */
>> +#ifdef CONFIG_FB_NUC900_DEBUG
>> +static int debug ? ? = 1;
>> +#define dprintk(msg...) ? ? ?{ printk(KERN_DEBUG "nuc900 lcd: " msg); }
>> +#else
>> +static int debug;
>> +#define dprintk(msg...)
>> +#endif
>
> Would be better to use the standard pr_debug(), rather than inventing
> private infrastructure. ?That way you get to enjoy the facilities which
> lib/dynamic_debug.c offers.
>
>> +
>> +/*
>> + * ?Initialize the nuc900 video (dual) buffer address
>> + */
>> +static void nuc900fb_set_lcdaddr(struct fb_info *info)
>> +{
>> + ? ? struct nuc900fb_info *fbi = info->par;
>> + ? ? void __iomem *regs = fbi->io;
>> + ? ? unsigned long vbaddr1, vbaddr2;
>> + ? ? vbaddr1 ?= info->fix.smem_start;
>
> It's conventional to put a blank line beterrn end-of-locals and start-of-code.
>
>> + ? ? vbaddr2 ?= info->fix.smem_start;
>> + ? ? vbaddr2 += info->fix.line_length * info->var.yres;
>> + ? ? /*set frambuffer start phy addr*/
>
> Like this:
>
> ? ? ? ?/* set frambuffer start phy addr */
>
>> + ? ? writel(vbaddr1, regs + REG_LCM_VA_BADDR0);
>> + ? ? writel(vbaddr2, regs + REG_LCM_VA_BADDR1);
>> +
>> + ? ? writel(fbi->regs.lcd_va_fbctrl, regs + REG_LCM_VA_FBCTRL);
>> + ? ? writel(fbi->regs.lcd_va_scale, regs + REG_LCM_VA_SCALE);
>> +}
>> +
>> +//static void nuc900fb_clk_select(struct fb_info *info, unsigned long pixclk)
>> +//{
>> +// ? struct nuc900fb_info *fbi = info->par;
>> +// ? int div;
>> +// ? if (clk <= 15 * 1000 * 1000) {
>> +// ? ? ? ? ? div = (15 * 1000 * 1000)/
>> +// ? ? ? ? ? nuc900_driver_clksrc_div(fbi->dev, "ext", 0x2);
>> +// ? }
>> +//
>> +//}
>
> Please feed the patch through scrupts/checkpatch.pl.
>
>> +/*
>> + * ? calculate divider for lcd div
>> + */
>> +static unsigned int nuc900fb_calc_pixclk(struct nuc900fb_info *fbi,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?unsigned long pixclk)
>> +{
>> + ? ? unsigned long clk = fbi->clk_rate;
>> + ? ? unsigned long long div;
>> +
>> + ? ? /* pixclk is in picseconds. our clock is in Hz*/
>> + ? ? /* div = (clk * pixclk)/10^12 */
>> + ? ? div = (unsigned long long)clk * pixclk;
>> + ? ? div >>= 12;
>> + ? ? do_div(div, 625 * 625UL * 625);
>> +
>> + ? ? dprintk("pixclk %ld, divisor is %ld\n", pixclk, (long)div);
>
> Perhaps use %lld and remove the cast.
>
>> + ? ? return div;
>> +}
>> +
>> +/*
>> + * ? Check the video params of 'var'.
>> + */
>> +static int nuc900fb_check_var(struct fb_var_screeninfo *var,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ?struct fb_info *info)
>> +{
>> + ? ? struct nuc900fb_info *fbi = info->par;
>> + ? ? struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
>> + ? ? struct nuc900fb_display *display = NULL;
>> + ? ? struct nuc900fb_display *default_display = mach_info->displays +
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?mach_info->default_display;
>> + ? ? int i;
>> +
>> + ? ? dprintk("check_var(var=%p, info=%p)\n", var, info);
>> +
>> + ? ? /* validate x/y resolution */
>> + ? ? /* choose default mode if possible */
>> + ? ? if (var->xres == default_display->xres &&
>> + ? ? ? ? var->yres == default_display->yres &&
>> + ? ? ? ? var->bits_per_pixel == default_display->bpp)
>> + ? ? ? ? ? ? display = default_display;
>> + ? ? else
>> + ? ? ? ? ? ? for (i = 0; i < mach_info->num_displays; i++)
>> + ? ? ? ? ? ? ? ? ? ? if (var->xres == mach_info->displays[i].xres &&
>> + ? ? ? ? ? ? ? ? ? ? ? ? var->yres == mach_info->displays[i].yres &&
>> + ? ? ? ? ? ? ? ? ? ? ? ? var->bits_per_pixel == mach_info->displays[i].bpp) {
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? display = mach_info->displays + i;
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? break;
>> + ? ? ? ? ? ? ? ? ? ? }
>> +
>> + ? ? if (display == NULL) {
>> + ? ? ? ? ? ? dprintk("wrong resolution or depth %dx%d at %d bit per pixel\n",
>> + ? ? ? ? ? ? ? ? ? ? var->xres, var->yres, var->bits_per_pixel);
>
> Some of the printks in here really should be printks, not the
> compile-time-suppressible dprintk(). ?Please review them all and
> convert the ones which will be useful to end-users into printk().
>
>> + ? ? ? ? ? ? return -EINVAL;
>> + ? ? }
>> +
>> + ? ? /* it should be the same size as the display */
>> + ? ? var->xres_virtual ? ? ? = display->xres;
>> + ? ? var->yres_virtual ? ? ? = display->yres;
>> + ? ? var->height ? ? ? ? ? ? = display->height;
>> + ? ? var->width ? ? ? ? ? ? ?= display->width;
>> +
>> + ? ? /* copy lcd settings */
>> + ? ? var->pixclock ? ? ? ? ? = display->pixclock;
>> + ? ? var->left_margin ? ? ? ?= display->left_margin;
>> + ? ? var->right_margin ? ? ? = display->right_margin;
>> + ? ? var->upper_margin ? ? ? = display->upper_margin;
>> + ? ? var->lower_margin ? ? ? = display->lower_margin;
>> + ? ? var->vsync_len ? ? ? ? ?= display->vsync_len;
>> + ? ? var->hsync_len ? ? ? ? ?= display->hsync_len;
>> +
>> + ? ? var->transp.offset ? ? ?= 0;
>> + ? ? var->transp.length ? ? ?= 0;
>> +
>> + ? ? fbi->regs.lcd_dccs = display->dccs;
>> + ? ? fbi->regs.lcd_device_ctrl = display->devctl;
>> + ? ? fbi->regs.lcd_va_fbctrl = display->fbctrl;
>> + ? ? fbi->regs.lcd_va_scale = display->scale;
>> +
>> + ? ? /* set R/G/B possions */
>> + ? ? switch (var->bits_per_pixel) {
>> + ? ? case 1:
>> + ? ? case 2:
>> + ? ? case 4:
>> + ? ? case 8:
>
> The above four lines are unneeded, but it's OK keeping them for
> documentation purposes.
>
>> + ? ? default:
>> + ? ? ? ? ? ? var->red.offset ? ? ? ? = 0;
>> + ? ? ? ? ? ? var->red.length ? ? ? ? = var->bits_per_pixel;
>> + ? ? ? ? ? ? var->green ? ? ? ? ? ? ?= var->red;
>> + ? ? ? ? ? ? var->blue ? ? ? ? ? ? ? = var->red;
>> + ? ? ? ? ? ? break;
>> + ? ? case 12:
>> + ? ? ? ? ? ? var->red.length ? ? ? ? = 4;
>> + ? ? ? ? ? ? var->green.length ? ? ? = 4;
>> + ? ? ? ? ? ? var->blue.length ? ? ? ?= 4;
>> + ? ? ? ? ? ? var->red.offset ? ? ? ? = 8;
>> + ? ? ? ? ? ? var->green.offset ? ? ? = 4;
>> + ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
>> + ? ? ? ? ? ? break;
>> + ? ? case 16:
>> + ? ? ? ? ? ? var->red.length ? ? ? ? = 5;
>> + ? ? ? ? ? ? var->green.length ? ? ? = 6;
>> + ? ? ? ? ? ? var->blue.length ? ? ? ?= 5;
>> + ? ? ? ? ? ? var->red.offset ? ? ? ? = 11;
>> + ? ? ? ? ? ? var->green.offset ? ? ? = 5;
>> + ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
>> + ? ? ? ? ? ? break;
>> + ? ? case 18:
>> + ? ? ? ? ? ? var->red.length ? ? ? ? = 6;
>> + ? ? ? ? ? ? var->green.length ? ? ? = 6;
>> + ? ? ? ? ? ? var->blue.length ? ? ? ?= 6;
>> + ? ? ? ? ? ? var->red.offset ? ? ? ? = 12;
>> + ? ? ? ? ? ? var->green.offset ? ? ? = 6;
>> + ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
>> + ? ? ? ? ? ? break;
>> + ? ? case 32:
>> + ? ? ? ? ? ? var->red.length ? ? ? ? = 8;
>> + ? ? ? ? ? ? var->green.length ? ? ? = 8;
>> + ? ? ? ? ? ? var->blue.length ? ? ? ?= 8;
>> + ? ? ? ? ? ? var->red.offset ? ? ? ? = 16;
>> + ? ? ? ? ? ? var->green.offset ? ? ? = 8;
>> + ? ? ? ? ? ? var->blue.offset ? ? ? ?= 0;
>> + ? ? ? ? ? ? break;
>> + ? ? }
>> +
>> + ? ? return 0;
>> +}
>> +
>> +/*
>> + * ? Calculate lcd register values from var setting & save into hw
>> + */
>> +static void nuc900fb_calculate_lcd_regs(const struct fb_info *info,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct nuc900fb_hw *regs)
>> +{
>> + ? ? const struct fb_var_screeninfo *var = &info->var;
>> + ? ? int vtt = var->height + var->upper_margin + var->lower_margin;
>> + ? ? int htt = var->width + var->left_margin + var->right_margin;
>> + ? ? int hsync = var->width + var->right_margin;
>> + ? ? int vsync = var->height + var->lower_margin;
>
> newline here, please.
>
>> + ? ? regs->lcd_crtc_size = LCM_CRTC_SIZE_VTTVAL(vtt) |
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_SIZE_HTTVAL(htt);
>> + ? ? regs->lcd_crtc_dend = LCM_CRTC_DEND_VDENDVAL(var->height) |
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_DEND_HDENDVAL(var->width);
>> + ? ? regs->lcd_crtc_hr = LCM_CRTC_HR_EVAL(var->width + 5) |
>> + ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_HR_SVAL(var->width + 1);
>> + ? ? regs->lcd_crtc_hsync = LCM_CRTC_HSYNC_EVAL(hsync + var->hsync_len) |
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ?LCM_CRTC_HSYNC_SVAL(hsync);
>> + ? ? regs->lcd_crtc_vr = LCM_CRTC_VR_EVAL(vsync + var->vsync_len) |
>> + ? ? ? ? ? ? ? ? ? ? ? ? LCM_CRTC_VR_SVAL(vsync);
>> +
>> +}
>> +
>>
>> ...
>>
>> +static int nuc900fb_debug_store(struct device *dev,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? struct device_attribute *attr,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? const char *buf, size_t len)
>> +{
>> + ? ? if (len < 1)
>> + ? ? ? ? ? ? return -EINVAL;
>> +
>> + ? ? if (strnicmp(buf, "on", 2) == 0 ||
>> + ? ? ? ? strnicmp(buf, "1", 1) == 0) {
>> + ? ? ? ? ? ? debug = 1;
>> + ? ? } else if (strnicmp(buf, "off", 3) == 0 ||
>> + ? ? ? ? ? ? ? ?strnicmp(buf, "0", 1) == 0) {
>> + ? ? ? ? ? ? debug = 0;
>> +
>> + ? ? } else {
>> + ? ? ? ? ? ? return -EINVAL;
>> + ? ? }
>> +
>> + ? ? return len;
>> +}
>
> Duplicates the above-mentioned dynamic-debug facility.
>
>> +static DEVICE_ATTR(debug, 0666, nuc900fb_debug_show, nuc900fb_debug_store);
>> +
>>
>> ...
>>
>> +static int __init nuc900fb_map_video_memory(struct fb_info *info)
>> +{
>> + ? ? struct nuc900fb_info *fbi = info->par;
>> + ? ? dma_addr_t map_dma;
>> + ? ? unsigned long map_size = PAGE_ALIGN(info->fix.smem_len);
>> +
>> + ? ? dprintk("nuc900fb_map_video_memory(fbi=%p) map_size %lu\n",
>> + ? ? ? ? ? ? fbi, map_size);
>> +
>> + ? ? info->screen_base = dma_alloc_writecombine(fbi->dev, map_size,
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? &map_dma, GFP_KERNEL);
>
> Here, do
>
> ? ? ? ?if (!info->screen_base)
> ? ? ? ? ? ? ? ?return -ENOMEM;
>
> and the rest of the function gets neater.
>
>
>> + ? ? if (info->screen_base != NULL) {
>> + ? ? ? ? ? ? dprintk("nuc900fb_map_video_memory: clear %p:%08lx\n",
>> + ? ? ? ? ? ? ? ? ? ? info->screen_base, map_size);
>> + ? ? ? ? ? ? memset(info->screen_base, 0x00, map_size);
>> +
>> + ? ? ? ? ? ? info->fix.smem_start = map_dma;
>> + ? ? ? ? ? ? dprintk("nuc900fb_map_video_memory: "
>> + ? ? ? ? ? ? ? ? ? ? "dma=%08lx cpu=%p size=%08lx\n",
>> + ? ? ? ? ? ? ? ? ? ? info->fix.smem_start, info->screen_base, map_size);
>> + ? ? }
>> + ? ? return (info->screen_base) ? 0 : -ENOMEM;
>> +}
>> +
>>
>> ...
>>
>> +static char driver_name[] = "nuc900fb";
>> +
>> +static int __init nuc900fb_probe(struct platform_device *pdev)
>
> Should this be __devinit?
>
>> +{
>> + ? ? struct nuc900fb_info *fbi;
>> + ? ? struct nuc900fb_display *display;
>> + ? ? struct fb_info ? ? *fbinfo;
>> + ? ? struct nuc900fb_mach_info *mach_info;
>> + ? ? struct resource *res;
>> + ? ? int ret;
>> + ? ? int irq;
>> + ? ? int i;
>> + ? ? int size;
>> +
>> + ? ? dprintk("devinit\n");
>> + ? ? mach_info = pdev->dev.platform_data;
>> + ? ? if (mach_info == NULL) {
>> + ? ? ? ? ? ? dev_err(&pdev->dev,
>> + ? ? ? ? ? ? ? ? ? ? "no platform data for lcd, cannot attach\n");
>> + ? ? ? ? ? ? return -EINVAL;
>> + ? ? }
>> +
>> + ? ? if (mach_info->default_display > mach_info->num_displays) {
>> + ? ? ? ? ? ? dev_err(&pdev->dev,
>> + ? ? ? ? ? ? ? ? ? ? "default display No. is %d but only %d displays \n",
>> + ? ? ? ? ? ? ? ? ? ? mach_info->default_display, mach_info->num_displays);
>> + ? ? ? ? ? ? return -EINVAL;
>> + ? ? }
>> +
>> +
>> + ? ? display = mach_info->displays + mach_info->default_display;
>> +
>> + ? ? irq = platform_get_irq(pdev, 0);
>> + ? ? if (irq < 0) {
>> + ? ? ? ? ? ? dev_err(&pdev->dev, "no irq for device\n");
>> + ? ? ? ? ? ? return -ENOENT;
>> + ? ? }
>> +
>> + ? ? fbinfo = framebuffer_alloc(sizeof(struct nuc900fb_info), &pdev->dev);
>> + ? ? if (!fbinfo)
>> + ? ? ? ? ? ? return -ENOMEM;
>> +
>> + ? ? platform_set_drvdata(pdev, fbinfo);
>> +
>> + ? ? fbi = fbinfo->par;
>> + ? ? fbi->dev = &pdev->dev;
>> +
>> +#ifdef CONFIG_CPU_NUC950
>> + ? ? fbi->drv_type = LCDDRV_NUC950;
>> +#endif
>> +
>> + ? ? res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +
>>
>> ...
>>
>> +static void nuc900fb_stop_lcd(struct fb_info *info)
>> +{
>> + ? ? struct nuc900fb_info *fbi = info->par;
>> + ? ? void __iomem *regs = fbi->io;
>> + ? ? unsigned long flags;
>> +
>> + ? ? local_irq_save(flags);
>> + ? ? writel((~LCM_DCCS_DISP_INT_EN) | (~LCM_DCCS_VA_EN) | (~LCM_DCCS_OSD_EN),
>> + ? ? ? ? ? ? regs + REG_LCM_DCCS);
>> + ? ? local_irq_restore(flags);
>> +}
>
> The local_irq_save() is a worry. ?What's it doing here? ?It does
> nothing to prevent an interrupt on another CPU!
>
>> +/*
>> + * ?Cleanup
>> + */
>> +static int nuc900fb_remove(struct platform_device *pdev)
>> +{
>> + ? ? struct fb_info *fbinfo = platform_get_drvdata(pdev);
>> + ? ? struct nuc900fb_info *fbi = fbinfo->par;
>> + ? ? int irq;
>> +
>> + ? ? nuc900fb_stop_lcd(fbinfo);
>> + ? ? msleep(1);
>> +
>> + ? ? nuc900fb_unmap_video_memory(fbinfo);
>> +
>> + ? ? iounmap(fbi->io);
>> +
>> + ? ? irq = platform_get_irq(pdev, 0);
>> + ? ? free_irq(irq, fbi);
>> +
>> + ? ? release_resource(fbi->mem);
>> + ? ? kfree(fbi->mem);
>> +
>> + ? ? platform_set_drvdata(pdev, NULL);
>> + ? ? framebuffer_release(fbinfo);
>> +
>> + ? ? return 0;
>> +}
>> +
>>
>> ...
>>
>
> The driver generally looks OK to me. ?Please cc me on any updates.
>
Thanks for your comments.
I will update my patch as soon as possible.
> --
> ????"NUC900 Linux BSP????".
> NUC900 Linux????????????
> NUC900 at googlegroups.com
> ?????????
> NUC900+unsubscribe at googlegroups.com
> ??????????
> https://groups.google.com/group/NUC900?hl=zh-CN
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [Linux-arm-nuc900] RE: [PATCH]NUC900 LCD Controller Driver
2010-01-30 0:37 ` H Hartley Sweeten
@ 2010-02-01 13:35 ` Qiang Wang
2010-02-02 5:14 ` Qiang Wang
0 siblings, 1 reply; 7+ messages in thread
From: Qiang Wang @ 2010-02-01 13:35 UTC (permalink / raw)
To: linux-arm-kernel
? 2010?1?30? ??8:37?H Hartley Sweeten <hartleys@visionengravers.com> ???
> On Friday, January 29, 2010 5:28 PM, Andrew Morton wrote:
>>
>> On Mon, 11 Jan 2010 17:05:44 +0900
>> Wang Qiang <rurality.linux@gmail.com> wrote:
>>
>>> hi, Dear Wan
>>>
>>> There is the patch of LCD controller driver for nuc900s.
>>> The Linux LOGO is just fine and the FB-Test application was ok, too.
>>>
>>> best regards
>>> wangqiang
>>>
>>>
>>> ...
>>>
>>> @@ -380,6 +381,48 @@ struct platform_device nuc900_device_kpi = {
>>> ? ? ?.resource ? ? ? = nuc900_kpi_resource,
>>> ?};
>>>
>>> +#ifdef CONFIG_FB_NUC900
>>> +
>>> +static struct resource nuc900_lcd_resource[] = {
>>> + ? ?[0] = {
>>> + ? ? ? ? ? ?.start = W90X900_PA_LCD,
>>> + ? ? ? ? ? ?.end ? = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
>>> + ? ? ? ? ? ?.flags = IORESOURCE_MEM,
>>> + ? ?},
>>> + ? ?[1] = {
>>> + ? ? ? ? ? ?.start = IRQ_LCD,
>>> + ? ? ? ? ? ?.end ? = IRQ_LCD,
>>> + ? ? ? ? ? ?.flags = IORESOURCE_IRQ,
>>> + ? ?}
>>> +};
>>> +
>>> +static u64 nuc900_device_lcd_dmamask = 0xffffffffUL;
>>
>> I suspect this should have type `dma_addr_t', but `struct device' uses
>> open-coded u64 too. ?Odd.
>>
>> It makes no sense to initialise a u64 with an unsigned long value -
>> it's wrong on a 32-bit machine.
>>
>> this:
>>
>> ? ? ? static u64 nuc900_device_lcd_dmamask = -1;
>>
>> will work.
>>
>>> +struct platform_device nuc900_device_lcd = {
>>> + ? ?.name ? ? ? ? ? ? = "nuc900-lcd",
>>> + ? ?.id ? ? ? ? ? ? ? = -1,
>>> + ? ?.num_resources ? ?= ARRAY_SIZE(nuc900_lcd_resource),
>>> + ? ?.resource ? ? ? ? = nuc900_lcd_resource,
>>> + ? ?.dev ? ? ? ? ? ? ?= {
>>> + ? ? ? ? ? ?.dma_mask ? ? ? ? ? ? ? = &nuc900_device_lcd_dmamask,
>>> + ? ? ? ? ? ?.coherent_dma_mask ? ? ?= 0xffffffffUL
>>
>> And this gets initialised to 0x00000000ffffffff also. ?Using -1 will fix.
>>
>
> Wouldn't this also work?
>
> ? ? ? ?.dev ? ? ? ? ? ? ? ? ? ?= {
> ? ? ? ? ? ? ? ?.dma_mask ? ? ? ? ? ? ? ? ? ? ? = &nuc900_device_lcd.dev.coherent_dma_mask,
> ? ? ? ? ? ? ? ?.coherent_dma_mask ? ? ?= DMA_BIT_MASK(32),
> ? ? ? ?},
>
> Then you could just get rid of nuc900_device_lcd_dmamask.
Yes, you are right.
I will use the DMA_BIT_MASK macro.
Thank you very much.
>
> Regards,
> Hartley
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [Linux-arm-nuc900] RE: [PATCH]NUC900 LCD Controller Driver
2010-02-01 13:35 ` [Linux-arm-nuc900] " Qiang Wang
@ 2010-02-02 5:14 ` Qiang Wang
0 siblings, 0 replies; 7+ messages in thread
From: Qiang Wang @ 2010-02-02 5:14 UTC (permalink / raw)
To: linux-arm-kernel
hello, Mr. Andrew Morton
I modified the nuc900 LCD Controller base on your comments.
Hope it will be fine:)
Best regards,
Wang Qiang
Signed-off-by: Wang Qiang <rurality.linux@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Wang Zongshun <mcuos.com@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
---
arch/arm/configs/nuc950_defconfig | 53 ++-
arch/arm/mach-w90x900/cpu.h | 1 +
arch/arm/mach-w90x900/dev.c | 42 ++
arch/arm/mach-w90x900/include/mach/fb.h | 83 +++
arch/arm/mach-w90x900/include/mach/regs-ldm.h | 253 ++++++++
arch/arm/mach-w90x900/mach-nuc950evb.c | 47 ++
arch/arm/mach-w90x900/nuc950.c | 4 +
drivers/video/Kconfig | 21 +
drivers/video/Makefile | 1 +
drivers/video/nuc900fb.c | 779 +++++++++++++++++++++++++
drivers/video/nuc900fb.h | 55 ++
11 files changed, 1338 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-w90x900/include/mach/fb.h
create mode 100644 arch/arm/mach-w90x900/include/mach/regs-ldm.h
create mode 100644 drivers/video/nuc900fb.c
create mode 100644 drivers/video/nuc900fb.h
diff --git a/arch/arm/configs/nuc950_defconfig
b/arch/arm/configs/nuc950_defconfig
index 97300ec..51cc2a2 100644
--- a/arch/arm/configs/nuc950_defconfig
+++ b/arch/arm/configs/nuc950_defconfig
@@ -590,8 +590,40 @@ CONFIG_SSB_POSSIBLE=y
#
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_NUC900=y
+CONFIG_GPM1040A0_320X240=y
+CONFIG_FB_NUC900_DEBUG=y
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+
#
# Display device support
@@ -603,6 +635,25 @@ CONFIG_SSB_POSSIBLE=y
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+CONFIG_FONT_8x16=y
+# CONFIG_FONT_6x11 is not set
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+
# CONFIG_SOUND is not set
# CONFIG_HID_SUPPORT is not set
CONFIG_USB_SUPPORT=y
diff --git a/arch/arm/mach-w90x900/cpu.h b/arch/arm/mach-w90x900/cpu.h
index 4d58ba1..f8730b6 100644
--- a/arch/arm/mach-w90x900/cpu.h
+++ b/arch/arm/mach-w90x900/cpu.h
@@ -57,3 +57,4 @@ extern struct platform_device nuc900_device_fmi;
extern struct platform_device nuc900_device_kpi;
extern struct platform_device nuc900_device_rtc;
extern struct platform_device nuc900_device_ts;
+extern struct platform_device nuc900_device_lcd;
diff --git a/arch/arm/mach-w90x900/dev.c b/arch/arm/mach-w90x900/dev.c
index ec711f4..4887612 100644
--- a/arch/arm/mach-w90x900/dev.c
+++ b/arch/arm/mach-w90x900/dev.c
@@ -34,6 +34,7 @@
#include <mach/regs-serial.h>
#include <mach/nuc900_spi.h>
#include <mach/map.h>
+#include <mach/fb.h>
#include "cpu.h"
@@ -380,6 +381,47 @@ struct platform_device nuc900_device_kpi = {
.resource = nuc900_kpi_resource,
};
+#ifdef CONFIG_FB_NUC900
+
+static struct resource nuc900_lcd_resource[] = {
+ [0] = {
+ .start = W90X900_PA_LCD,
+ .end = W90X900_PA_LCD + W90X900_SZ_LCD - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_LCD,
+ .end = IRQ_LCD,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 nuc900_device_lcd_dmamask = -1;
+struct platform_device nuc900_device_lcd = {
+ .name = "nuc900-lcd",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(nuc900_lcd_resource),
+ .resource = nuc900_lcd_resource,
+ .dev = {
+ .dma_mask = &nuc900_device_lcd_dmamask,
+ .coherent_dma_mask = -1,
+ }
+};
+
+void nuc900_fb_set_platdata(struct nuc900fb_mach_info *pd)
+{
+ struct nuc900fb_mach_info *npd;
+
+ npd = kmalloc(sizeof(*npd), GFP_KERNEL);
+ if (npd) {
+ memcpy(npd, pd, sizeof(*npd));
+ nuc900_device_lcd.dev.platform_data = npd;
+ } else {
+ printk(KERN_ERR "no memory for LCD platform data\n");
+ }
+}
+#endif
+
/*Here should be your evb resourse,such as LCD*/
static struct platform_device *nuc900_public_dev[] __initdata = {
diff --git a/arch/arm/mach-w90x900/include/mach/fb.h
b/arch/arm/mach-w90x900/include/mach/fb.h
new file mode 100644
index 0000000..cec5ece
--- /dev/null
+++ b/arch/arm/mach-w90x900/include/mach/fb.h
@@ -0,0 +1,83 @@
+/* linux/include/asm/arch-nuc900/fb.h
+ *
+ * Copyright (c) 2008 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Changelog:
+ *
+ * 2008/08/26 vincen.zswan modify this file for LCD.
+ */
+
+#ifndef __ASM_ARM_FB_H
+#define __ASM_ARM_FB_H
+
+
+
+/* LCD Controller Hardware Desc */
+struct nuc900fb_hw {
+ unsigned int lcd_dccs;
+ unsigned int lcd_device_ctrl;
+ unsigned int lcd_mpulcd_cmd;
+ unsigned int lcd_int_cs;
+ unsigned int lcd_crtc_size;
+ unsigned int lcd_crtc_dend;
+ unsigned int lcd_crtc_hr;
+ unsigned int lcd_crtc_hsync;
+ unsigned int lcd_crtc_vr;
+ unsigned int lcd_va_baddr0;
+ unsigned int lcd_va_baddr1;
+ unsigned int lcd_va_fbctrl;
+ unsigned int lcd_va_scale;
+ unsigned int lcd_va_test;
+ unsigned int lcd_va_win;
+ unsigned int lcd_va_stuff;
+};
+
+/* LCD Display Description */
+struct nuc900fb_display {
+ /* LCD Image type */
+ unsigned type;
+
+ /* LCD Screen Size */
+ unsigned short width;
+ unsigned short height;
+
+ /* LCD Screen Info */
+ unsigned short xres;
+ unsigned short yres;
+ unsigned short bpp;
+
+ unsigned long pixclock;
+ unsigned short left_margin;
+ unsigned short right_margin;
+ unsigned short hsync_len;
+ unsigned short upper_margin;
+ unsigned short lower_margin;
+ unsigned short vsync_len;
+
+ /* hardware special register value */
+ unsigned int dccs;
+ unsigned int devctl;
+ unsigned int fbctrl;
+ unsigned int scale;
+};
+
+struct nuc900fb_mach_info {
+ struct nuc900fb_display *displays;
+ unsigned num_displays;
+ unsigned default_display;
+ /* GPIO Setting Info */
+ unsigned gpio_dir;
+ unsigned gpio_dir_mask;
+ unsigned gpio_data;
+ unsigned gpio_data_mask;
+};
+
+extern void __init nuc900_fb_set_platdata(struct nuc900fb_mach_info *);
+
+#endif /* __ASM_ARM_FB_H */
diff --git a/arch/arm/mach-w90x900/include/mach/regs-ldm.h
b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
new file mode 100644
index 0000000..e9d480a
--- /dev/null
+++ b/arch/arm/mach-w90x900/include/mach/regs-ldm.h
@@ -0,0 +1,253 @@
+/*
+ * arch/arm/mach-w90x900/include/mach/regs-serial.h
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Description:
+ * Nuvoton Display, LCM Register list
+ * Author: Wang Qiang (rurality.linux at gmail.com) 2009/12/11
+ *
+ */
+
+
+#ifndef __ASM_ARM_W90X900_REGS_LDM_H
+#define __ASM_ARM_W90X900_REGS_LDM_H
+
+#include <mach/map.h>
+
+/* Display Controller Control/Status Register */
+#define REG_LCM_DCCS (0x00)
+
+#define LCM_DCCS_ENG_RST (1 << 0)
+#define LCM_DCCS_VA_EN (1 << 1)
+#define LCM_DCCS_OSD_EN (1 << 2)
+#define LCM_DCCS_DISP_OUT_EN (1 << 3)
+#define LCM_DCCS_DISP_INT_EN (1 << 4)
+#define LCM_DCCS_CMD_ON (1 << 5)
+#define LCM_DCCS_FIELD_INTR (1 << 6)
+#define LCM_DCCS_SINGLE (1 << 7)
+
+enum LCM_DCCS_VA_SRC {
+ LCM_DCCS_VA_SRC_YUV422 = (0 << 8),
+ LCM_DCCS_VA_SRC_YCBCR422 = (1 << 8),
+ LCM_DCCS_VA_SRC_RGB888 = (2 << 8),
+ LCM_DCCS_VA_SRC_RGB666 = (3 << 8),
+ LCM_DCCS_VA_SRC_RGB565 = (4 << 8),
+ LCM_DCCS_VA_SRC_RGB444LOW = (5 << 8),
+ LCM_DCCS_VA_SRC_RGB444HIGH = (7 << 8)
+};
+
+
+/* Display Device Control Register */
+#define REG_LCM_DEV_CTRL (0x04)
+
+enum LCM_DEV_CTRL_SWAP_YCbCr {
+ LCM_DEV_CTRL_SWAP_UYVY = (0 << 1),
+ LCM_DEV_CTRL_SWAP_YUYV = (1 << 1),
+ LCM_DEV_CTRL_SWAP_VYUY = (2 << 1),
+ LCM_DEV_CTRL_SWAP_YVYU = (3 << 1)
+};
+
+enum LCM_DEV_CTRL_RGB_SHIFT {
+ LCM_DEV_CTRL_RGB_SHIFT_NOT = (0 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_ONECYCLE = (1 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_TWOCYCLE = (2 << 3),
+ LCM_DEV_CTRL_RGB_SHIFT_NOT_DEF = (3 << 3)
+};
+
+enum LCM_DEV_CTRL_DEVICE {
+ LCM_DEV_CTRL_DEVICE_YUV422 = (0 << 5),
+ LCM_DEV_CTRL_DEVICE_YUV444 = (1 << 5),
+ LCM_DEV_CTRL_DEVICE_UNIPAC = (4 << 5),
+ LCM_DEV_CTRL_DEVICE_SEIKO_EPSON = (5 << 5),
+ LCM_DEV_CTRL_DEVICE_HIGH_COLOR = (6 << 5),
+ LCM_DEV_CTRL_DEVICE_MPU = (7 << 5)
+};
+
+#define LCM_DEV_CTRL_LCD_DDA (8)
+#define LCM_DEV_CTRL_YUV2CCIR (16)
+
+enum LCM_DEV_CTRL_LCD_SEL {
+ LCM_DEV_CTRL_LCD_SEL_RGB_GBR = (0 << 17),
+ LCM_DEV_CTRL_LCD_SEL_BGR_RBG = (1 << 17),
+ LCM_DEV_CTRL_LCD_SEL_GBR_RGB = (2 << 17),
+ LCM_DEV_CTRL_LCD_SEL_RBG_BGR = (3 << 17)
+};
+
+enum LCM_DEV_CTRL_FAL_D {
+ LCM_DEV_CTRL_FAL_D_FALLING = (0 << 19),
+ LCM_DEV_CTRL_FAL_D_RISING = (1 << 19),
+};
+
+enum LCM_DEV_CTRL_H_POL {
+ LCM_DEV_CTRL_H_POL_LOW = (0 << 20),
+ LCM_DEV_CTRL_H_POL_HIGH = (1 << 20),
+};
+
+enum LCM_DEV_CTRL_V_POL {
+ LCM_DEV_CTRL_V_POL_LOW = (0 << 21),
+ LCM_DEV_CTRL_V_POL_HIGH = (1 << 21),
+};
+
+enum LCM_DEV_CTRL_VR_LACE {
+ LCM_DEV_CTRL_VR_LACE_NINTERLACE = (0 << 22),
+ LCM_DEV_CTRL_VR_LACE_INTERLACE = (1 << 22),
+};
+
+enum LCM_DEV_CTRL_LACE {
+ LCM_DEV_CTRL_LACE_NINTERLACE = (0 << 23),
+ LCM_DEV_CTRL_LACE_INTERLACE = (1 << 23),
+};
+
+enum LCM_DEV_CTRL_RGB_SCALE {
+ LCM_DEV_CTRL_RGB_SCALE_4096 = (0 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_65536 = (1 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_262144 = (2 << 24),
+ LCM_DEV_CTRL_RGB_SCALE_16777216 = (3 << 24),
+};
+
+enum LCM_DEV_CTRL_DBWORD {
+ LCM_DEV_CTRL_DBWORD_HALFWORD = (0 << 26),
+ LCM_DEV_CTRL_DBWORD_FULLWORD = (1 << 26),
+};
+
+enum LCM_DEV_CTRL_MPU68 {
+ LCM_DEV_CTRL_MPU68_80_SERIES = (0 << 27),
+ LCM_DEV_CTRL_MPU68_68_SERIES = (1 << 27),
+};
+
+enum LCM_DEV_CTRL_DE_POL {
+ LCM_DEV_CTRL_DE_POL_HIGH = (0 << 28),
+ LCM_DEV_CTRL_DE_POL_LOW = (1 << 28),
+};
+
+#define LCM_DEV_CTRL_CMD16 (29)
+#define LCM_DEV_CTRL_CM16t18 (30)
+#define LCM_DEV_CTRL_CMD_LOW (31)
+
+/* MPU-Interface LCD Write Command */
+#define REG_LCM_MPU_CMD (0x08)
+
+/* Interrupt Control/Status Register */
+#define REG_LCM_INT_CS (0x0c)
+#define LCM_INT_CS_DISP_F_EN (1 << 0)
+#define LCM_INT_CS_UNDERRUN_EN (1 << 1)
+#define LCM_INT_CS_BUS_ERROR_INT (1 << 28)
+#define LCM_INT_CS_UNDERRUN_INT (1 << 29)
+#define LCM_INT_CS_DISP_F_STATUS (1 << 30)
+#define LCM_INT_CS_DISP_F_INT (1 << 31)
+
+/* CRTC Display Size Control Register */
+#define REG_LCM_CRTC_SIZE (0x10)
+#define LCM_CRTC_SIZE_VTTVAL(x) ((x) << 16)
+#define LCM_CRTC_SIZE_HTTVAL(x) ((x) << 0)
+
+/* CRTC Display Enable End */
+#define REG_LCM_CRTC_DEND (0x14)
+#define LCM_CRTC_DEND_VDENDVAL(x) ((x) << 16)
+#define LCM_CRTC_DEND_HDENDVAL(x) ((x) << 0)
+
+/* CRTC Internal Horizontal Retrace Control Register */
+#define REG_LCM_CRTC_HR (0x18)
+#define LCM_CRTC_HR_EVAL(x) ((x) << 16)
+#define LCM_CRTC_HR_SVAL(x) ((x) << 0)
+
+/* CRTC Horizontal Sync Control Register */
+#define REG_LCM_CRTC_HSYNC (0x1C)
+#define LCM_CRTC_HSYNC_SHIFTVAL(x) ((x) << 30)
+#define LCM_CRTC_HSYNC_EVAL(x) ((x) << 16)
+#define LCM_CRTC_HSYNC_SVAL(x) ((x) << 0)
+
+/* CRTC Internal Vertical Retrace Control Register */
+#define REG_LCM_CRTC_VR (0x20)
+#define LCM_CRTC_VR_EVAL(x) ((x) << 16)
+#define LCM_CRTC_VR_SVAL(x) ((x) << 0)
+
+/* Video Stream Frame Buffer-0 Starting Address */
+#define REG_LCM_VA_BADDR0 (0x24)
+
+/* Video Stream Frame Buffer-1 Starting Address */
+#define REG_LCM_VA_BADDR1 (0x28)
+
+/* Video Stream Frame Buffer Control Register */
+#define REG_LCM_VA_FBCTRL (0x2C)
+#define LCM_VA_FBCTRL_IO_REGION_HALF (1 << 28)
+#define LCM_VA_FBCTRL_FIELD_DUAL (1 << 29)
+#define LCM_VA_FBCTRL_START_BUF (1 << 30)
+#define LCM_VA_FBCTRL_DB_EN (1 << 31)
+
+/* Video Stream Scaling Control Register */
+#define REG_LCM_VA_SCALE (0x30)
+#define LCM_VA_SCALE_XCOPY_INTERPOLATION (0 << 15)
+#define LCM_VA_SCALE_XCOPY_DUPLICATION (1 << 15)
+
+/* Image Stream Active Window Coordinates */
+#define REG_LCM_VA_WIN (0x38)
+
+/* Image Stream Stuff Pixel */
+#define REG_LCM_VA_STUFF (0x3C)
+
+/* OSD Window Starting Coordinates */
+#define REG_LCM_OSD_WINS (0x40)
+
+/* OSD Window Ending Coordinates */
+#define REG_LCM_OSD_WINE (0x44)
+
+/* OSD Stream Frame Buffer Starting Address */
+#define REG_LCM_OSD_BADDR (0x48)
+
+/* OSD Stream Frame Buffer Control Register */
+#define REG_LCM_OSD_FBCTRL (0x4c)
+
+/* OSD Overlay Control Register */
+#define REG_LCM_OSD_OVERLAY (0x50)
+
+/* OSD Overlay Color-Key Pattern Register */
+#define REG_LCM_OSD_CKEY (0x54)
+
+/* OSD Overlay Color-Key Mask Register */
+#define REG_LCM_OSD_CMASK (0x58)
+
+/* OSD Window Skip1 Register */
+#define REG_LCM_OSD_SKIP1 (0x5C)
+
+/* OSD Window Skip2 Register */
+#define REG_LCM_OSD_SKIP2 (0x60)
+
+/* OSD horizontal up scaling control register */
+#define REG_LCM_OSD_SCALE (0x64)
+
+/* MPU Vsync control register */
+#define REG_LCM_MPU_VSYNC (0x68)
+
+/* Hardware cursor control Register */
+#define REG_LCM_HC_CTRL (0x6C)
+
+/* Hardware cursot tip point potison on va picture */
+#define REG_LCM_HC_POS (0x70)
+
+/* Hardware Cursor Window Buffer Control Register */
+#define REG_LCM_HC_WBCTRL (0x74)
+
+/* Hardware cursor memory base address register */
+#define REG_LCM_HC_BADDR (0x78)
+
+/* Hardware cursor color ram register mapped to bpp = 0 */
+#define REG_LCM_HC_COLOR0 (0x7C)
+
+/* Hardware cursor color ram register mapped to bpp = 1 */
+#define REG_LCM_HC_COLOR1 (0x80)
+
+/* Hardware cursor color ram register mapped to bpp = 2 */
+#define REG_LCM_HC_COLOR2 (0x84)
+
+/* Hardware cursor color ram register mapped to bpp = 3 */
+#define REG_LCM_HC_COLOR3 (0x88)
+
+#endif /* __ASM_ARM_W90X900_REGS_LDM_H */
diff --git a/arch/arm/mach-w90x900/mach-nuc950evb.c
b/arch/arm/mach-w90x900/mach-nuc950evb.c
index cef903b..b3edc3c 100644
--- a/arch/arm/mach-w90x900/mach-nuc950evb.c
+++ b/arch/arm/mach-w90x900/mach-nuc950evb.c
@@ -10,6 +10,8 @@
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation;version 2 of the License.
+ * history:
+ * Wang Qiang (rurality.linux@gmail.com) add LCD support
*
*/
@@ -18,9 +20,51 @@
#include <asm/mach/map.h>
#include <asm/mach-types.h>
#include <mach/map.h>
+#include <mach/regs-ldm.h>
+#include <mach/fb.h>
#include "nuc950.h"
+#ifdef CONFIG_FB_NUC900
+/* LCD Controller */
+static struct nuc900fb_display __initdata nuc950_lcd_info[] = {
+ /* Giantplus Technology GPM1040A0 320x240 Color TFT LCD */
+ [0] = {
+ .type = LCM_DCCS_VA_SRC_RGB565,
+ .width = 320,
+ .height = 240,
+ .xres = 320,
+ .yres = 240,
+ .bpp = 16,
+ .pixclock = 200000,
+ .left_margin = 34,
+ .right_margin = 54,
+ .hsync_len = 10,
+ .upper_margin = 18,
+ .lower_margin = 4,
+ .vsync_len = 1,
+ .dccs = 0x8e00041a,
+ .devctl = 0x060800c0,
+ .fbctrl = 0x00a000a0,
+ .scale = 0x04000400,
+ },
+};
+
+static struct nuc900fb_mach_info nuc950_fb_info __initdata = {
+#if defined(CONFIG_GPM1040A0_320X240)
+ .displays = &nuc950_lcd_info[0],
+#else
+ .displays = nuc950_lcd_info,
+#endif
+ .num_displays = ARRAY_SIZE(nuc950_lcd_info),
+ .default_display = 0,
+ .gpio_dir = 0x00000004,
+ .gpio_dir_mask = 0xFFFFFFFD,
+ .gpio_data = 0x00000004,
+ .gpio_data_mask = 0xFFFFFFFD,
+};
+#endif
+
static void __init nuc950evb_map_io(void)
{
nuc950_map_io();
@@ -30,6 +74,9 @@ static void __init nuc950evb_map_io(void)
static void __init nuc950evb_init(void)
{
nuc950_board_init();
+#ifdef CONFIG_FB_NUC900
+ nuc900_fb_set_platdata(&nuc950_fb_info);
+#endif
}
MACHINE_START(W90P950EVB, "W90P950EVB")
diff --git a/arch/arm/mach-w90x900/nuc950.c b/arch/arm/mach-w90x900/nuc950.c
index 1495081..4d1f1ab 100644
--- a/arch/arm/mach-w90x900/nuc950.c
+++ b/arch/arm/mach-w90x900/nuc950.c
@@ -18,6 +18,7 @@
#include <linux/platform_device.h>
#include <asm/mach/map.h>
#include <mach/hardware.h>
+
#include "cpu.h"
/* define specific CPU platform device */
@@ -25,6 +26,9 @@
static struct platform_device *nuc950_dev[] __initdata = {
&nuc900_device_kpi,
&nuc900_device_fmi,
+#ifdef CONFIG_FB_NUC900
+ &nuc900_device_lcd,
+#endif
};
/* define specific CPU platform io map */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 5a5c303..a943e5e 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1945,6 +1945,27 @@ config FB_S3C2410_DEBUG
Turn on debugging messages. Note that you can set/unset at run time
through sysfs
+config FB_NUC900
+ bool "NUC900 LCD framebuffer support"
+ depends on FB && ARCH_W90X900
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ ---help---
+ Frame buffer driver for the built-in LCD controller in the Nuvoton
+ NUC900 processor
+
+config GPM1040A0_320X240
+ bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
+ depends on FB_NUC900
+
+config FB_NUC900_DEBUG
+ bool "NUC900 lcd debug messages"
+ depends on FB_NUC900
+ help
+ Turn on debugging messages. Note that you can set/unset at run time
+ through sysfs
+
config FB_SM501
tristate "Silicon Motion SM501 framebuffer support"
depends on FB && MFD_SM501
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 4ecb30c..a42ad55 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -129,6 +129,7 @@ obj-$(CONFIG_XEN_FBDEV_FRONTEND) += xen-fbfront.o
obj-$(CONFIG_FB_CARMINE) += carminefb.o
obj-$(CONFIG_FB_MB862XX) += mb862xx/
obj-$(CONFIG_FB_MSM) += msm/
+obj-$(CONFIG_FB_NUC900) += nuc900fb.o
# Platform or fallback drivers go here
obj-$(CONFIG_FB_UVESA) += uvesafb.o
diff --git a/drivers/video/nuc900fb.c b/drivers/video/nuc900fb.c
new file mode 100644
index 0000000..6bf0d46
--- /dev/null
+++ b/drivers/video/nuc900fb.c
@@ -0,0 +1,779 @@
+/*
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Description:
+ * Nuvoton LCD Controller Driver
+ * Author:
+ * Wang Qiang (rurality.linux at gmail.com) 2009/12/11
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/mm.h>
+#include <linux/tty.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/workqueue.h>
+#include <linux/wait.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/cpufreq.h>
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <linux/device.h>
+
+#include <mach/map.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-ldm.h>
+#include <mach/fb.h>
+#include <mach/clkdev.h>
+
+#include "nuc900fb.h"
+
+
+/*
+ * Initialize the nuc900 video (dual) buffer address
+ */
+static void nuc900fb_set_lcdaddr(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+ unsigned long vbaddr1, vbaddr2;
+
+ vbaddr1 = info->fix.smem_start;
+ vbaddr2 = info->fix.smem_start;
+ vbaddr2 += info->fix.line_length * info->var.yres;
+
+ /* set frambuffer start phy addr*/
+ writel(vbaddr1, regs + REG_LCM_VA_BADDR0);
+ writel(vbaddr2, regs + REG_LCM_VA_BADDR1);
+
+ writel(fbi->regs.lcd_va_fbctrl, regs + REG_LCM_VA_FBCTRL);
+ writel(fbi->regs.lcd_va_scale, regs + REG_LCM_VA_SCALE);
+}
+
+/*
+ * calculate divider for lcd div
+ */
+static unsigned int nuc900fb_calc_pixclk(struct nuc900fb_info *fbi,
+ unsigned long pixclk)
+{
+ unsigned long clk = fbi->clk_rate;
+ unsigned long long div;
+
+ /* pixclk is in picseconds. our clock is in Hz*/
+ /* div = (clk * pixclk)/10^12 */
+ div = (unsigned long long)clk * pixclk;
+ div >>= 12;
+ do_div(div, 625 * 625UL * 625);
+
+ dev_dbg(fbi->dev, "pixclk %ld, divisor is %lld\n", pixclk, div);
+
+ return div;
+}
+
+/*
+ * Check the video params of 'var'.
+ */
+static int nuc900fb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
+ struct nuc900fb_display *display = NULL;
+ struct nuc900fb_display *default_display = mach_info->displays +
+ mach_info->default_display;
+ int i;
+
+ dev_dbg(fbi->dev, "check_var(var=%p, info=%p)\n", var, info);
+
+ /* validate x/y resolution */
+ /* choose default mode if possible */
+ if (var->xres == default_display->xres &&
+ var->yres == default_display->yres &&
+ var->bits_per_pixel == default_display->bpp)
+ display = default_display;
+ else
+ for (i = 0; i < mach_info->num_displays; i++)
+ if (var->xres == mach_info->displays[i].xres &&
+ var->yres == mach_info->displays[i].yres &&
+ var->bits_per_pixel == mach_info->displays[i].bpp) {
+ display = mach_info->displays + i;
+ break;
+ }
+
+ if (display == NULL) {
+ printk(KERN_ERR "wrong resolution or depth %dx%d at %d bit per pixel\n",
+ var->xres, var->yres, var->bits_per_pixel);
+ return -EINVAL;
+ }
+
+ /* it should be the same size as the display */
+ var->xres_virtual = display->xres;
+ var->yres_virtual = display->yres;
+ var->height = display->height;
+ var->width = display->width;
+
+ /* copy lcd settings */
+ var->pixclock = display->pixclock;
+ var->left_margin = display->left_margin;
+ var->right_margin = display->right_margin;
+ var->upper_margin = display->upper_margin;
+ var->lower_margin = display->lower_margin;
+ var->vsync_len = display->vsync_len;
+ var->hsync_len = display->hsync_len;
+
+ var->transp.offset = 0;
+ var->transp.length = 0;
+
+ fbi->regs.lcd_dccs = display->dccs;
+ fbi->regs.lcd_device_ctrl = display->devctl;
+ fbi->regs.lcd_va_fbctrl = display->fbctrl;
+ fbi->regs.lcd_va_scale = display->scale;
+
+ /* set R/G/B possions */
+ switch (var->bits_per_pixel) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ default:
+ var->red.offset = 0;
+ var->red.length = var->bits_per_pixel;
+ var->green = var->red;
+ var->blue = var->red;
+ break;
+ case 12:
+ var->red.length = 4;
+ var->green.length = 4;
+ var->blue.length = 4;
+ var->red.offset = 8;
+ var->green.offset = 4;
+ var->blue.offset = 0;
+ break;
+ case 16:
+ var->red.length = 5;
+ var->green.length = 6;
+ var->blue.length = 5;
+ var->red.offset = 11;
+ var->green.offset = 5;
+ var->blue.offset = 0;
+ break;
+ case 18:
+ var->red.length = 6;
+ var->green.length = 6;
+ var->blue.length = 6;
+ var->red.offset = 12;
+ var->green.offset = 6;
+ var->blue.offset = 0;
+ break;
+ case 32:
+ var->red.length = 8;
+ var->green.length = 8;
+ var->blue.length = 8;
+ var->red.offset = 16;
+ var->green.offset = 8;
+ var->blue.offset = 0;
+ break;
+ }
+
+ return 0;
+}
+
+/*
+ * Calculate lcd register values from var setting & save into hw
+ */
+static void nuc900fb_calculate_lcd_regs(const struct fb_info *info,
+ struct nuc900fb_hw *regs)
+{
+ const struct fb_var_screeninfo *var = &info->var;
+ int vtt = var->height + var->upper_margin + var->lower_margin;
+ int htt = var->width + var->left_margin + var->right_margin;
+ int hsync = var->width + var->right_margin;
+ int vsync = var->height + var->lower_margin;
+
+ regs->lcd_crtc_size = LCM_CRTC_SIZE_VTTVAL(vtt) |
+ LCM_CRTC_SIZE_HTTVAL(htt);
+ regs->lcd_crtc_dend = LCM_CRTC_DEND_VDENDVAL(var->height) |
+ LCM_CRTC_DEND_HDENDVAL(var->width);
+ regs->lcd_crtc_hr = LCM_CRTC_HR_EVAL(var->width + 5) |
+ LCM_CRTC_HR_SVAL(var->width + 1);
+ regs->lcd_crtc_hsync = LCM_CRTC_HSYNC_EVAL(hsync + var->hsync_len) |
+ LCM_CRTC_HSYNC_SVAL(hsync);
+ regs->lcd_crtc_vr = LCM_CRTC_VR_EVAL(vsync + var->vsync_len) |
+ LCM_CRTC_VR_SVAL(vsync);
+
+}
+
+/*
+ * Activate (set) the controller from the given framebuffer
+ * information
+ */
+static void nuc900fb_activate_var(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+ struct fb_var_screeninfo *var = &info->var;
+ int clkdiv;
+
+ clkdiv = nuc900fb_calc_pixclk(fbi, var->pixclock) - 1;
+ if (clkdiv < 0)
+ clkdiv = 0;
+
+ nuc900fb_calculate_lcd_regs(info, &fbi->regs);
+
+ /* set the new lcd registers*/
+
+ dev_dbg(fbi->dev, "new lcd register set:\n");
+ dev_dbg(fbi->dev, "dccs = 0x%08x\n", fbi->regs.lcd_dccs);
+ dev_dbg(fbi->dev, "dev_ctl = 0x%08x\n", fbi->regs.lcd_device_ctrl);
+ dev_dbg(fbi->dev, "crtc_size = 0x%08x\n", fbi->regs.lcd_crtc_size);
+ dev_dbg(fbi->dev, "crtc_dend = 0x%08x\n", fbi->regs.lcd_crtc_dend);
+ dev_dbg(fbi->dev, "crtc_hr = 0x%08x\n", fbi->regs.lcd_crtc_hr);
+ dev_dbg(fbi->dev, "crtc_hsync = 0x%08x\n", fbi->regs.lcd_crtc_hsync);
+ dev_dbg(fbi->dev, "crtc_vr = 0x%08x\n", fbi->regs.lcd_crtc_vr);
+
+ writel(fbi->regs.lcd_device_ctrl, regs + REG_LCM_DEV_CTRL);
+ writel(fbi->regs.lcd_crtc_size, regs + REG_LCM_CRTC_SIZE);
+ writel(fbi->regs.lcd_crtc_dend, regs + REG_LCM_CRTC_DEND);
+ writel(fbi->regs.lcd_crtc_hr, regs + REG_LCM_CRTC_HR);
+ writel(fbi->regs.lcd_crtc_hsync, regs + REG_LCM_CRTC_HSYNC);
+ writel(fbi->regs.lcd_crtc_vr, regs + REG_LCM_CRTC_VR);
+
+ /* set lcd address pointers */
+ nuc900fb_set_lcdaddr(info);
+
+ writel(fbi->regs.lcd_dccs, regs + REG_LCM_DCCS);
+}
+
+/*
+ * Alters the hardware state.
+ *
+ */
+static int nuc900fb_set_par(struct fb_info *info)
+{
+ struct fb_var_screeninfo *var = &info->var;
+
+ switch (var->bits_per_pixel) {
+ case 32:
+ case 24:
+ case 18:
+ case 16:
+ case 12:
+ info->fix.visual = FB_VISUAL_TRUECOLOR;
+ break;
+ case 1:
+ info->fix.visual = FB_VISUAL_MONO01;
+ break;
+ default:
+ info->fix.visual = FB_VISUAL_PSEUDOCOLOR;
+ break;
+ }
+
+ info->fix.line_length = (var->xres_virtual * var->bits_per_pixel) / 8;
+
+ /* activate this new configuration */
+ nuc900fb_activate_var(info);
+ return 0;
+}
+
+static inline unsigned int chan_to_field(unsigned int chan,
+ struct fb_bitfield *bf)
+{
+ chan &= 0xffff;
+ chan >>= 16 - bf->length;
+ return chan << bf->offset;
+}
+
+static int nuc900fb_setcolreg(unsigned regno,
+ unsigned red, unsigned green, unsigned blue,
+ unsigned transp, struct fb_info *info)
+{
+ unsigned int val;
+
+ switch (info->fix.visual) {
+ case FB_VISUAL_TRUECOLOR:
+ /* true-colour, use pseuo-palette */
+ if (regno < 16) {
+ u32 *pal = info->pseudo_palette;
+
+ val = chan_to_field(red, &info->var.red);
+ val |= chan_to_field(green, &info->var.green);
+ val |= chan_to_field(blue, &info->var.blue);
+ pal[regno] = val;
+ }
+ break;
+
+ default:
+ return 1; /* unknown type */
+ }
+ return 0;
+}
+
+/**
+ * nuc900fb_blank
+ *
+ */
+static int nuc900fb_blank(int blank_mode, struct fb_info *info)
+{
+
+ return 0;
+}
+
+static struct fb_ops nuc900fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = nuc900fb_check_var,
+ .fb_set_par = nuc900fb_set_par,
+ .fb_blank = nuc900fb_blank,
+ .fb_setcolreg = nuc900fb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+
+static inline void modify_gpio(void __iomem *reg,
+ unsigned long set, unsigned long mask)
+{
+ unsigned long tmp;
+ tmp = readl(reg) & ~mask;
+ writel(tmp | set, reg);
+}
+
+/*
+ * Initialise LCD-related registers
+ */
+static int nuc900fb_init_registers(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ struct nuc900fb_mach_info *mach_info = fbi->dev->platform_data;
+ void __iomem *regs = fbi->io;
+
+ /*reset the display engine*/
+ writel(0, regs + REG_LCM_DCCS);
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_ENG_RST,
+ regs + REG_LCM_DCCS);
+ ndelay(100);
+ writel(readl(regs + REG_LCM_DCCS) & (~LCM_DCCS_ENG_RST),
+ regs + REG_LCM_DCCS);
+ ndelay(100);
+
+ writel(0, regs + REG_LCM_DEV_CTRL);
+
+ /* config gpio output */
+ modify_gpio(W90X900_VA_GPIO + 0x54, mach_info->gpio_dir,
+ mach_info->gpio_dir_mask);
+ modify_gpio(W90X900_VA_GPIO + 0x58, mach_info->gpio_data,
+ mach_info->gpio_data_mask);
+
+ return 0;
+}
+
+
+/*
+ * Alloc the SDRAM region of NUC900 for the frame buffer.
+ * The buffer should be a non-cached, non-buffered, memory region
+ * to allow palette and pixel writes without flushing the cache.
+ */
+static int __init nuc900fb_map_video_memory(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ dma_addr_t map_dma;
+ unsigned long map_size = PAGE_ALIGN(info->fix.smem_len);
+
+ dev_dbg(fbi->dev, "nuc900fb_map_video_memory(fbi=%p) map_size %lu\n",
+ fbi, map_size);
+
+ info->screen_base = dma_alloc_writecombine(fbi->dev, map_size,
+ &map_dma, GFP_KERNEL);
+
+ if (!info->screen_base)
+ return -ENOMEM;
+
+ memset(info->screen_base, 0x00, map_size);
+ info->fix.smem_start = map_dma;
+
+ return 0;
+}
+
+static inline void nuc900fb_unmap_video_memory(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ dma_free_writecombine(fbi->dev, PAGE_ALIGN(info->fix.smem_len),
+ info->screen_base, info->fix.smem_start);
+}
+
+static irqreturn_t nuc900fb_irqhandler(int irq, void *dev_id)
+{
+ struct nuc900fb_info *fbi = dev_id;
+ void __iomem *regs = fbi->io;
+ void __iomem *irq_base = fbi->irq_base;
+ unsigned long lcdirq = readl(regs + REG_LCM_INT_CS);
+
+ if (lcdirq & LCM_INT_CS_DISP_F_STATUS) {
+ writel(readl(irq_base) | 1<<30, irq_base);
+
+ /* wait VA_EN low */
+ if ((readl(regs + REG_LCM_DCCS) &
+ LCM_DCCS_SINGLE) == LCM_DCCS_SINGLE)
+ while ((readl(regs + REG_LCM_DCCS) &
+ LCM_DCCS_VA_EN) == LCM_DCCS_VA_EN)
+ ;
+ /* display_out-enable */
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_DISP_OUT_EN,
+ regs + REG_LCM_DCCS);
+ /* va-enable*/
+ writel(readl(regs + REG_LCM_DCCS) | LCM_DCCS_VA_EN,
+ regs + REG_LCM_DCCS);
+ } else if (lcdirq & LCM_INT_CS_UNDERRUN_INT) {
+ writel(readl(irq_base) | LCM_INT_CS_UNDERRUN_INT, irq_base);
+ } else if (lcdirq & LCM_INT_CS_BUS_ERROR_INT) {
+ writel(readl(irq_base) | LCM_INT_CS_BUS_ERROR_INT, irq_base);
+ }
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_CPU_FREQ
+
+static int nuc900fb_cpufreq_transition(struct notifier_block *nb,
+ unsigned long val, void *data)
+{
+ struct nuc900fb_info *info;
+ struct fb_info *fbinfo;
+ long delta_f;
+ info = container_of(nb, struct nuc900fb_info, freq_transition);
+ fbinfo = platform_get_drvdata(to_platform_device(info->dev));
+
+ delta_f = info->clk_rate - clk_get_rate(info->clk);
+
+ if ((val == CPUFREQ_POSTCHANGE && delta_f > 0) ||
+ (val == CPUFREQ_PRECHANGE && delta_f < 0)) {
+ info->clk_rate = clk_get_rate(info->clk);
+ nuc900fb_activate_var(fbinfo);
+ }
+
+ return 0;
+}
+
+static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
+{
+ fbi->freq_transition.notifier_call = nuc900fb_cpufreq_transition;
+ return cpufreq_register_notifier(&fbi->freq_transition,
+ CPUFREQ_TRANSITION_NOTIFIER);
+}
+
+static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *fbi)
+{
+ cpufreq_unregister_notifier(&fbi->freq_transition,
+ CPUFREQ_TRANSITION_NOTIFIER);
+}
+#else
+static inline int nuc900fb_cpufreq_transition(struct notifier_block *nb,
+ unsigned long val, void *data)
+{
+ return 0;
+}
+
+static inline int nuc900fb_cpufreq_register(struct nuc900fb_info *fbi)
+{
+ return 0;
+}
+
+static inline void nuc900fb_cpufreq_deregister(struct nuc900fb_info *info)
+{
+}
+#endif
+
+static char driver_name[] = "nuc900fb";
+
+static int __devinit nuc900fb_probe(struct platform_device *pdev)
+{
+ struct nuc900fb_info *fbi;
+ struct nuc900fb_display *display;
+ struct fb_info *fbinfo;
+ struct nuc900fb_mach_info *mach_info;
+ struct resource *res;
+ int ret;
+ int irq;
+ int i;
+ int size;
+
+ dev_dbg(&pdev->dev, "devinit\n");
+ mach_info = pdev->dev.platform_data;
+ if (mach_info == NULL) {
+ dev_err(&pdev->dev,
+ "no platform data for lcd, cannot attach\n");
+ return -EINVAL;
+ }
+
+ if (mach_info->default_display > mach_info->num_displays) {
+ dev_err(&pdev->dev,
+ "default display No. is %d but only %d displays \n",
+ mach_info->default_display, mach_info->num_displays);
+ return -EINVAL;
+ }
+
+
+ display = mach_info->displays + mach_info->default_display;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no irq for device\n");
+ return -ENOENT;
+ }
+
+ fbinfo = framebuffer_alloc(sizeof(struct nuc900fb_info), &pdev->dev);
+ if (!fbinfo)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, fbinfo);
+
+ fbi = fbinfo->par;
+ fbi->dev = &pdev->dev;
+
+#ifdef CONFIG_CPU_NUC950
+ fbi->drv_type = LCDDRV_NUC950;
+#endif
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ size = (res->end - res->start) + 1;
+ fbi->mem = request_mem_region(res->start, size, pdev->name);
+ if (fbi->mem == NULL) {
+ dev_err(&pdev->dev, "failed to alloc memory region\n");
+ ret = -ENOENT;
+ goto free_fb;
+ }
+
+ fbi->io = ioremap(res->start, size);
+ if (fbi->io == NULL) {
+ dev_err(&pdev->dev, "ioremap() of lcd registers failed\n");
+ ret = -ENXIO;
+ goto release_mem_region;
+ }
+
+ fbi->irq_base = fbi->io + REG_LCM_INT_CS;
+
+
+ /* Stop the LCD */
+ writel(0, fbi->io + REG_LCM_DCCS);
+
+ /* fill the fbinfo*/
+ strcpy(fbinfo->fix.id, driver_name);
+ fbinfo->fix.type = FB_TYPE_PACKED_PIXELS;
+ fbinfo->fix.type_aux = 0;
+ fbinfo->fix.xpanstep = 0;
+ fbinfo->fix.ypanstep = 0;
+ fbinfo->fix.ywrapstep = 0;
+ fbinfo->fix.accel = FB_ACCEL_NONE;
+ fbinfo->var.nonstd = 0;
+ fbinfo->var.activate = FB_ACTIVATE_NOW;
+ fbinfo->var.accel_flags = 0;
+ fbinfo->var.vmode = FB_VMODE_NONINTERLACED;
+ fbinfo->fbops = &nuc900fb_ops;
+ fbinfo->flags = FBINFO_FLAG_DEFAULT;
+ fbinfo->pseudo_palette = &fbi->pseudo_pal;
+
+ ret = request_irq(irq, nuc900fb_irqhandler, IRQF_DISABLED,
+ pdev->name, fbinfo);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot register irq handler %d -err %d\n",
+ irq, ret);
+ ret = -EBUSY;
+ goto release_regs;
+ }
+
+ nuc900_driver_clksrc_div(&pdev->dev, "ext", 0x2);
+
+ fbi->clk = clk_get(&pdev->dev, NULL);
+ if (!fbi->clk || IS_ERR(fbi->clk)) {
+ printk(KERN_ERR "nuc900-lcd:failed to get lcd clock source\n");
+ ret = -ENOENT;
+ goto release_irq;
+ }
+
+ clk_enable(fbi->clk);
+ dev_dbg(&pdev->dev, "got and enabled clock\n");
+
+ fbi->clk_rate = clk_get_rate(fbi->clk);
+
+ /* calutate the video buffer size */
+ for (i = 0; i < mach_info->num_displays; i++) {
+ unsigned long smem_len = mach_info->displays[i].xres;
+ smem_len *= mach_info->displays[i].yres;
+ smem_len *= mach_info->displays[i].bpp;
+ smem_len >>= 3;
+ if (fbinfo->fix.smem_len < smem_len)
+ fbinfo->fix.smem_len = smem_len;
+ }
+
+ /* Initialize Video Memory */
+ ret = nuc900fb_map_video_memory(fbinfo);
+ if (ret) {
+ printk(KERN_ERR "Failed to allocate video RAM: %x\n", ret);
+ goto release_clock;
+ }
+
+ dev_dbg(&pdev->dev, "got video memory\n");
+
+ fbinfo->var.xres = display->xres;
+ fbinfo->var.yres = display->yres;
+ fbinfo->var.bits_per_pixel = display->bpp;
+
+ nuc900fb_init_registers(fbinfo);
+
+ nuc900fb_check_var(&fbinfo->var, fbinfo);
+
+ ret = nuc900fb_cpufreq_register(fbi);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to register cpufreq\n");
+ goto free_video_memory;
+ }
+
+ ret = register_framebuffer(fbinfo);
+ if (ret) {
+ printk(KERN_ERR "failed to register framebuffer device: %d\n",
+ ret);
+ goto free_cpufreq;
+ }
+
+ printk(KERN_INFO "fb%d: %s frame buffer device\n",
+ fbinfo->node, fbinfo->fix.id);
+
+ return 0;
+
+free_cpufreq:
+ nuc900fb_cpufreq_deregister(fbi);
+free_video_memory:
+ nuc900fb_unmap_video_memory(fbinfo);
+release_clock:
+ clk_disable(fbi->clk);
+ clk_put(fbi->clk);
+release_irq:
+ free_irq(irq, fbi);
+release_regs:
+ iounmap(fbi->io);
+release_mem_region:
+ release_mem_region((unsigned long)fbi->mem, size);
+free_fb:
+ framebuffer_release(fbinfo);
+ return ret;
+}
+
+/*
+ * shutdown the lcd controller
+ */
+static void nuc900fb_stop_lcd(struct fb_info *info)
+{
+ struct nuc900fb_info *fbi = info->par;
+ void __iomem *regs = fbi->io;
+
+ writel((~LCM_DCCS_DISP_INT_EN) | (~LCM_DCCS_VA_EN) | (~LCM_DCCS_OSD_EN),
+ regs + REG_LCM_DCCS);
+}
+
+/*
+ * Cleanup
+ */
+static int nuc900fb_remove(struct platform_device *pdev)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(pdev);
+ struct nuc900fb_info *fbi = fbinfo->par;
+ int irq;
+
+ nuc900fb_stop_lcd(fbinfo);
+ msleep(1);
+
+ nuc900fb_unmap_video_memory(fbinfo);
+
+ iounmap(fbi->io);
+
+ irq = platform_get_irq(pdev, 0);
+ free_irq(irq, fbi);
+
+ release_resource(fbi->mem);
+ kfree(fbi->mem);
+
+ platform_set_drvdata(pdev, NULL);
+ framebuffer_release(fbinfo);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+
+/*
+ * suspend and resume support for the lcd controller
+ */
+
+static int nuc900fb_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(dev);
+ struct nuc900fb_info *info = fbinfo->par;
+
+ nuc900fb_stop_lcd();
+ msleep(1);
+ clk_disable(info->clk);
+ return 0;
+}
+
+static int nuc900fb_resume(struct platform_device *dev)
+{
+ struct fb_info *fbinfo = platform_get_drvdata(dev);
+ struct nuc900fb_info *fbi = fbinfo->par;
+
+ printk(KERN_INFO "nuc900fb resume\n");
+
+ clk_enable(fbi->clk);
+ msleep(1);
+
+ nuc900fb_init_registers(fbinfo);
+ nuc900fb_activate_var(bfinfo);
+
+ return 0;
+}
+
+#else
+#define nuc900fb_suspend NULL
+#define nuc900fb_resume NULL
+#endif
+
+static struct platform_driver nuc900fb_driver = {
+ .probe = nuc900fb_probe,
+ .remove = nuc900fb_remove,
+ .suspend = nuc900fb_suspend,
+ .resume = nuc900fb_resume,
+ .driver = {
+ .name = "nuc900-lcd",
+ .owner = THIS_MODULE,
+ },
+};
+
+int __devinit nuc900fb_init(void)
+{
+ return platform_driver_register(&nuc900fb_driver);
+}
+
+static void __exit nuc900fb_cleanup(void)
+{
+ platform_driver_unregister(&nuc900fb_driver);
+}
+
+module_init(nuc900fb_init);
+module_exit(nuc900fb_cleanup);
+
+MODULE_DESCRIPTION("Framebuffer driver for the NUC900");
+MODULE_LICENSE("GPL");
diff --git a/drivers/video/nuc900fb.h b/drivers/video/nuc900fb.h
new file mode 100644
index 0000000..6c23aa3
--- /dev/null
+++ b/drivers/video/nuc900fb.h
@@ -0,0 +1,55 @@
+/*
+ *
+ * Copyright (c) 2009 Nuvoton technology corporation
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Auther:
+ * Wang Qiang(rurality.linux at gmail.com) 2009/12/16
+ */
+
+#ifndef __NUC900FB_H
+#define __NUC900FB_H
+
+#include <mach/map.h>
+#include <mach/fb.h>
+
+enum nuc900_lcddrv_type {
+ LCDDRV_NUC910,
+ LCDDRV_NUC930,
+ LCDDRV_NUC932,
+ LCDDRV_NUC950,
+ LCDDRV_NUC960,
+};
+
+
+#define PALETTE_BUFFER_SIZE 256
+#define PALETTE_BUFF_CLEAR (0x80000000) /* entry is clear/invalid */
+
+struct nuc900fb_info {
+ struct device *dev;
+ struct clk *clk;
+
+ struct resource *mem;
+ void __iomem *io;
+ void __iomem *irq_base;
+ int drv_type;
+ struct nuc900fb_hw regs;
+ unsigned long clk_rate;
+
+#ifdef CONFIG_CPU_FREQ
+ struct notifier_block freq_transition;
+#endif
+
+ /* keep these registers in case we need to re-write palette */
+ u32 palette_buffer[PALETTE_BUFFER_SIZE];
+ u32 pseudo_pal[16];
+};
+
+int nuc900fb_init(void);
+
+#endif /* __NUC900FB_H */
--
1.6.4
-------------- next part --------------
A non-text attachment was scrubbed...
Name: nuc900-lcd-controller-driver.patch
Type: application/octet-stream
Size: 40989 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100202/a7a554a2/attachment-0001.obj>
^ permalink raw reply related [flat|nested] 7+ messages in thread
end of thread, other threads:[~2010-02-02 5:14 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-11 8:05 [PATCH]NUC900 LCD Controller Driver Wang Qiang
2010-01-28 9:00 ` Qiang Wang
2010-01-30 0:27 ` Andrew Morton
2010-01-30 0:37 ` H Hartley Sweeten
2010-02-01 13:35 ` [Linux-arm-nuc900] " Qiang Wang
2010-02-02 5:14 ` Qiang Wang
2010-02-01 13:33 ` [Linux-arm-nuc900] " Qiang Wang
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).