[PATCH v5 2/2] [media] atmel-isc: DT binding for Image Sensor Controller driver

[songjun.wu@atmel.com (Wu, Songjun)]

Hi Rob,

Thank you for your comments.

On 6/20/2016 21:25, Rob Herring wrote:
> On Fri, Jun 17, 2016 at 04:57:14PM +0800, Songjun Wu wrote:
>> DT binding documentation for ISC driver.
>>
>> Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
>> ---
>>
>> Changes in v5:
>> - Add clock names.
>>
>> Changes in v4:
>> - Remove the isc clock nodes.
>>
>> Changes in v3:
>> - Remove the 'atmel,sensor-preferred'.
>> - Modify the isc clock node according to the Rob's remarks.
>>
>> Changes in v2:
>> - Remove the unit address of the endpoint.
>> - Add the unit address to the clock node.
>> - Avoid using underscores in node names.
>> - Drop the "0x" in the unit address of the i2c node.
>> - Modify the description of 'atmel,sensor-preferred'.
>> - Add the description for the ISC internal clock.
>>
>>  .../devicetree/bindings/media/atmel-isc.txt        | 64 ++++++++++++++++++++++
>>  1 file changed, 64 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/media/atmel-isc.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
>> new file mode 100644
>> index 0000000..9558a77
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
>> @@ -0,0 +1,64 @@
>> +Atmel Image Sensor Controller (ISC)
>> +----------------------------------------------
>> +
>> +Required properties for ISC:
>> +- compatible
>> +	Must be "atmel,sama5d2-isc".
>> +- reg
>> +	Physical base address and length of the registers set for the device.
>> +- interrupts
>> +	Should contain IRQ line for the ISC.
>> +- clocks
>> +	List of clock specifiers, corresponding to entries in
>> +	the clock-names property;
>> +	Please refer to clock-bindings.txt.
>> +- clock-names
>> +	Required elements: "hclock".
>
> What about the 2 other clocks in the example?
>
The other clocks is optional, not required.
Do you have any suggestion?

>> +- #clock-cells
>> +	Should be 0.
>> +- clock-output-names
>> +	Should contain the name of the clock driving the sensor master clock.
>
> State what the name is.
>
"isc-mck" will be added.

>> +- pinctrl-names, pinctrl-0
>> +	Please refer to pinctrl-bindings.txt.
>> +
>> +ISC supports a single port node with parallel bus. It should contain one
>> +'port' child node with child 'endpoint' node. Please refer to the bindings
>> +defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
>> +
>> +Example:
>> +isc: isc at f0008000 {
>> +	compatible = "atmel,sama5d2-isc";
>> +	reg = <0xf0008000 0x4000>;
>> +	interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
>> +	clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
>> +	clock-names = "hclock", "iscck", "gck";
>> +	#clock-cells = <0>;
>> +	clock-output-names = "isc-mck";
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
>> +
>> +	port {
>> +		isc_0: endpoint {
>> +			remote-endpoint = <&ov7740_0>;
>> +			hsync-active = <1>;
>> +			vsync-active = <0>;
>> +			pclk-sample = <1>;
>> +		};
>> +	};
>> +};
>> +
>> +i2c1: i2c at fc028000 {
>> +	ov7740: camera at 21 {
>> +	compatible = "ovti,ov7740";
>
> Indentation is still wrong here...
>
Sorry, my mistake.
It should be fixed.

>> +	reg = <0x21>;
>> +	clocks = <&isc>;
>> +	clock-names = "xvclk";
>> +	assigned-clocks = <&isc>;
>> +	assigned-clock-rates = <24000000>;
>> +
>> +	port {
>> +		ov7740_0: endpoint {
>> +			remote-endpoint = <&isc_0>;
>> +		};
>> +	};
>> +};
>> --
>> 2.7.4
>>