Re: ARM WFET application scenario consultation

From: Marc Zyngier <maz@kernel.org>
To: Catalin Marinas <catalin.marinas@arm.com>
Cc: yangwendong <yangwendong@huawei.com>,
	Will Deacon <will@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Martin Weidmann <Martin.Weidmann@arm.com>,
	linux-arm-kernel@lists.infradead.org, wanghaibin.wang@huawei.com,
	Zenghui Yu <yuzenghui@huawei.com>,
	"wangjingyi (D)" <wangjingyi11@huawei.com>
Subject: Re: ARM WFET application scenario consultation
Date: Mon, 12 Apr 2021 15:02:00 +0100	[thread overview]
Message-ID: <875z0rob3b.wl-maz@kernel.org> (raw)
In-Reply-To: <877dl7obpc.wl-maz@kernel.org>

On Mon, 12 Apr 2021 14:48:47 +0100,
Marc Zyngier <maz@kernel.org> wrote:
> 
> On Mon, 12 Apr 2021 14:15:21 +0100,
> Catalin Marinas <catalin.marinas@arm.com> wrote:
> > 
> > On Mon, Apr 12, 2021 at 02:09:10PM +0100, Marc Zyngier wrote:
> > > On Mon, 12 Apr 2021 13:46:37 +0100,
> > > Catalin Marinas <catalin.marinas@arm.com> wrote:
> > > > 
> > > > On Mon, Apr 12, 2021 at 08:08:23PM +0800, yangwendong wrote:
> > > > > Recently, a new feature of WFE with timeouts has been added to ARMv8.
> > > > > I have some doubts about the application scenarios of this feature.
> > > > > 
> > > > > 1) Arm spec said that WFE or WFET can be used in spinlock. Since the
> > > > > thread using spinlock can't be sleep, if we use the wfet instruction, we
> > > > > can do nothing but wait when timeout,  so what's the difference between
> > > > > the two instructions in this scenario?
> > > > 
> > > > Not much point in using it it in a classic spinlock, unless you have
> > > > some specific implementation that's supposed to time out.
> > > > 
> > > > Note that we already enabled the event stream in Linux so that an event
> > > > is generated at 100KHz waking up any WFE. One reason we had for this was
> > > > some hardware errata where events between clusters were not generated.
> > > > Another was some small delays required in in certain user programs
> > > > without going through a kernel syscall, though not sure anyone's
> > > > actually using it.
> > > > 
> > > > > 2) Are there any other special scenarios where using wfet instructions
> > > > > can be beneficial ?
> > > > 
> > > > In the kernel we could replace our udelay loop with WFIT for example
> > > > (not WFET because of the event stream). As for user, we can expose a
> > > > HWCAP but it's up to user libraries to make use of it.
> > > 
> > > Note that since c219bc4e9205K ("arm64: Trap WFI executed in
> > > userspace"), we actively prevent WFI from being used in userspace, and
> > > I would expect WFIT to be given the same treatment. It otherwise is a
> > > precise tool for userspace to synchronise against kernel events.
> > 
> > I agree. I only thought about using it in the kernel as a simpler
> > udelay(). The user should not attempt WFI/WFIT.
> 
> That's my position as well. I'll post a patch dealing with that
> shortly.

Actually, no need for that. WFIT gets correctly trapped and skipped
because ESR_ELx_WFx_ISS_TI only covers bit 0, meaning that WFIT is
handled just like WFI.

	M.

-- 
Without deviation from the norm, progress is not possible.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel