Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000

linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed

* Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000
       [not found] <20230202093706.30995-1-mrkiko.rs@gmail.com>
@ 2023-02-03 17:46 ` Pali Rohár
  2023-03-29 19:39   ` Pali Rohár
  2023-04-07 15:24   ` Gregory CLEMENT
  0 siblings, 2 replies; 3+ messages in thread
From: Pali Rohár @ 2023-02-03 17:46 UTC (permalink / raw)
  To: Gregory CLEMENT, Andrew Lunn, devicetree, linux-arm-kernel,
	linux-kernel

On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
> The GL-MV1000 (Brume) is a small form-factor gateway router.
> It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
> 
> Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
> CC: Pali <pali@kernel.org>

Looks good,

Reviewed-by: Pali Rohár <pali@kernel.org>

> ---
>  arch/arm64/boot/dts/marvell/Makefile          |   1 +
>  .../dts/marvell/armada-3720-gl-mv1000.dts     | 239 ++++++++++++++++++
>  2 files changed, 240 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> 
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index 058237681fe5..79ac09b58a89 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
>  dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> new file mode 100644
> index 000000000000..b1b45b4fa9d4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> @@ -0,0 +1,239 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "armada-372x.dtsi"
> +
> +/ {
> +	model = "GL.iNet GL-MV1000";
> +	compatible = "glinet,gl-mv1000", "marvell,armada3720";
> +
> +	aliases {
> +		led-boot = &led_power;
> +		led-failsafe = &led_power;
> +		led-running = &led_power;
> +		led-upgrade = &led_power;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> +	};
> +
> +	vcc_sd_reg1: regulator {
> +		compatible = "regulator-gpio";
> +		regulator-name = "vcc_sd1";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +
> +		gpios-states = <0>;
> +		states = <1800000 0x1
> +			3300000 0x0>;
> +		enable-active-high;
> +	};
> +
> +	keys {
> +		compatible = "gpio-keys";
> +
> +		reset {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		switch {
> +			label = "switch";
> +			linux,code = <BTN_0>;
> +			gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		vpn {
> +			label = "green:vpn";
> +			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wan {
> +			label = "green:wan";
> +			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		led_power: power {
> +			label = "green:power";
> +			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> +			default-state = "on";
> +		};
> +	};
> +};
> +
> +&spi0 {
> +	status = "okay";
> +
> +	flash@0 {
> +		reg = <0>;
> +		compatible = "jedec,spi-nor";
> +		spi-max-frequency = <104000000>;
> +		m25p,fast-read;
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition@0 {
> +				label = "firmware";
> +				reg = <0 0xf0000>;
> +			};
> +
> +			partition@f0000 {
> +				label = "u-boot-env";
> +				reg = <0xf0000 0x8000>;
> +			};
> +
> +			factory: partition@f8000 {
> +				label = "factory";
> +				reg = <0xf8000 0x8000>;
> +				read-only;
> +			};
> +
> +			partition@100000 {
> +				label = "dtb";
> +				reg = <0x100000 0x10000>;
> +				read-only;
> +			};
> +
> +			partition@110000 {
> +				label = "rescue";
> +				reg = <0x110000 0x1000000>;
> +			};
> +		};
> +	};
> +};
> +
> +&sdhci1 {
> +	wp-inverted;
> +	bus-width = <4>;
> +	cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
> +	marvell,pad-type = "sd";
> +	no-1-8-v;
> +	vqmmc-supply = <&vcc_sd_reg1>;
> +	status = "okay";
> +};
> +
> +&sdhci0 {
> +	bus-width = <8>;
> +	mmc-ddr-1_8v;
> +	mmc-hs400-1_8v;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	marvell,pad-type = "fixed-1-8v";
> +	status = "okay";
> +};
> +
> +&usb3 {
> +	status = "okay";
> +};
> +
> +&usb2 {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&mdio {
> +	switch0: switch0@1 {
> +		compatible = "marvell,mv88e6085";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <1>;
> +
> +		dsa,member = <0 0>;
> +
> +		ports: ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				label = "cpu";
> +				ethernet = <&eth0>;
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				label = "wan";
> +				phy-handle = <&switch0phy0>;
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				label = "lan0";
> +				phy-handle = <&switch0phy1>;
> +
> +				nvmem-cells = <&macaddr_factory_6>;
> +				nvmem-cell-names = "mac-address";
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				label = "lan1";
> +				phy-handle = <&switch0phy2>;
> +
> +				nvmem-cells = <&macaddr_factory_6>;
> +				nvmem-cell-names = "mac-address";
> +			};
> +		};
> +
> +		mdio {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			switch0phy0: switch0phy0@11 {
> +				reg = <0x11>;
> +			};
> +			switch0phy1: switch0phy1@12 {
> +				reg = <0x12>;
> +			};
> +			switch0phy2: switch0phy2@13 {
> +				reg = <0x13>;
> +			};
> +		};
> +	};
> +};
> +
> +&eth0 {
> +	nvmem-cells = <&macaddr_factory_0>;
> +	nvmem-cell-names = "mac-address";
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> +
> +&factory {
> +	compatible = "nvmem-cells";
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +
> +	macaddr_factory_0: macaddr@0 {
> +		reg = <0x0 0x6>;
> +	};
> +
> +	macaddr_factory_6: macaddr@6 {
> +		reg = <0x6 0x6>;
> +	};
> +};
> -- 
> 2.39.1
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000
  2023-02-03 17:46 ` [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000 Pali Rohár
@ 2023-03-29 19:39   ` Pali Rohár
  2023-04-07 15:24   ` Gregory CLEMENT
  1 sibling, 0 replies; 3+ messages in thread
From: Pali Rohár @ 2023-03-29 19:39 UTC (permalink / raw)
  To: Gregory CLEMENT, Andrew Lunn, devicetree, linux-arm-kernel,
	linux-kernel

PING?

On Friday 03 February 2023 18:46:18 Pali Rohár wrote:
> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
> > The GL-MV1000 (Brume) is a small form-factor gateway router.
> > It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
> > 
> > Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
> > CC: Pali <pali@kernel.org>
> 
> Looks good,
> 
> Reviewed-by: Pali Rohár <pali@kernel.org>
> 
> > ---
> >  arch/arm64/boot/dts/marvell/Makefile          |   1 +
> >  .../dts/marvell/armada-3720-gl-mv1000.dts     | 239 ++++++++++++++++++
> >  2 files changed, 240 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > 
> > diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> > index 058237681fe5..79ac09b58a89 100644
> > --- a/arch/arm64/boot/dts/marvell/Makefile
> > +++ b/arch/arm64/boot/dts/marvell/Makefile
> > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
> > +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
> >  dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> > diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > new file mode 100644
> > index 000000000000..b1b45b4fa9d4
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
> > @@ -0,0 +1,239 @@
> > +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> > +
> > +/dts-v1/;
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include "armada-372x.dtsi"
> > +
> > +/ {
> > +	model = "GL.iNet GL-MV1000";
> > +	compatible = "glinet,gl-mv1000", "marvell,armada3720";
> > +
> > +	aliases {
> > +		led-boot = &led_power;
> > +		led-failsafe = &led_power;
> > +		led-running = &led_power;
> > +		led-upgrade = &led_power;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	memory@0 {
> > +		device_type = "memory";
> > +		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> > +	};
> > +
> > +	vcc_sd_reg1: regulator {
> > +		compatible = "regulator-gpio";
> > +		regulator-name = "vcc_sd1";
> > +		regulator-min-microvolt = <1800000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-boot-on;
> > +
> > +		gpios-states = <0>;
> > +		states = <1800000 0x1
> > +			3300000 0x0>;
> > +		enable-active-high;
> > +	};
> > +
> > +	keys {
> > +		compatible = "gpio-keys";
> > +
> > +		reset {
> > +			label = "reset";
> > +			linux,code = <KEY_RESTART>;
> > +			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		switch {
> > +			label = "switch";
> > +			linux,code = <BTN_0>;
> > +			gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
> > +		};
> > +	};
> > +
> > +	leds {
> > +		compatible = "gpio-leds";
> > +
> > +		vpn {
> > +			label = "green:vpn";
> > +			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		wan {
> > +			label = "green:wan";
> > +			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
> > +		};
> > +
> > +		led_power: power {
> > +			label = "green:power";
> > +			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
> > +			default-state = "on";
> > +		};
> > +	};
> > +};
> > +
> > +&spi0 {
> > +	status = "okay";
> > +
> > +	flash@0 {
> > +		reg = <0>;
> > +		compatible = "jedec,spi-nor";
> > +		spi-max-frequency = <104000000>;
> > +		m25p,fast-read;
> > +		partitions {
> > +			compatible = "fixed-partitions";
> > +			#address-cells = <1>;
> > +			#size-cells = <1>;
> > +
> > +			partition@0 {
> > +				label = "firmware";
> > +				reg = <0 0xf0000>;
> > +			};
> > +
> > +			partition@f0000 {
> > +				label = "u-boot-env";
> > +				reg = <0xf0000 0x8000>;
> > +			};
> > +
> > +			factory: partition@f8000 {
> > +				label = "factory";
> > +				reg = <0xf8000 0x8000>;
> > +				read-only;
> > +			};
> > +
> > +			partition@100000 {
> > +				label = "dtb";
> > +				reg = <0x100000 0x10000>;
> > +				read-only;
> > +			};
> > +
> > +			partition@110000 {
> > +				label = "rescue";
> > +				reg = <0x110000 0x1000000>;
> > +			};
> > +		};
> > +	};
> > +};
> > +
> > +&sdhci1 {
> > +	wp-inverted;
> > +	bus-width = <4>;
> > +	cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
> > +	marvell,pad-type = "sd";
> > +	no-1-8-v;
> > +	vqmmc-supply = <&vcc_sd_reg1>;
> > +	status = "okay";
> > +};
> > +
> > +&sdhci0 {
> > +	bus-width = <8>;
> > +	mmc-ddr-1_8v;
> > +	mmc-hs400-1_8v;
> > +	non-removable;
> > +	no-sd;
> > +	no-sdio;
> > +	marvell,pad-type = "fixed-1-8v";
> > +	status = "okay";
> > +};
> > +
> > +&usb3 {
> > +	status = "okay";
> > +};
> > +
> > +&usb2 {
> > +	status = "okay";
> > +};
> > +
> > +&uart0 {
> > +	status = "okay";
> > +};
> > +
> > +&mdio {
> > +	switch0: switch0@1 {
> > +		compatible = "marvell,mv88e6085";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		reg = <1>;
> > +
> > +		dsa,member = <0 0>;
> > +
> > +		ports: ports {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			port@0 {
> > +				reg = <0>;
> > +				label = "cpu";
> > +				ethernet = <&eth0>;
> > +			};
> > +
> > +			port@1 {
> > +				reg = <1>;
> > +				label = "wan";
> > +				phy-handle = <&switch0phy0>;
> > +			};
> > +
> > +			port@2 {
> > +				reg = <2>;
> > +				label = "lan0";
> > +				phy-handle = <&switch0phy1>;
> > +
> > +				nvmem-cells = <&macaddr_factory_6>;
> > +				nvmem-cell-names = "mac-address";
> > +			};
> > +
> > +			port@3 {
> > +				reg = <3>;
> > +				label = "lan1";
> > +				phy-handle = <&switch0phy2>;
> > +
> > +				nvmem-cells = <&macaddr_factory_6>;
> > +				nvmem-cell-names = "mac-address";
> > +			};
> > +		};
> > +
> > +		mdio {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			switch0phy0: switch0phy0@11 {
> > +				reg = <0x11>;
> > +			};
> > +			switch0phy1: switch0phy1@12 {
> > +				reg = <0x12>;
> > +			};
> > +			switch0phy2: switch0phy2@13 {
> > +				reg = <0x13>;
> > +			};
> > +		};
> > +	};
> > +};
> > +
> > +&eth0 {
> > +	nvmem-cells = <&macaddr_factory_0>;
> > +	nvmem-cell-names = "mac-address";
> > +	phy-mode = "rgmii-id";
> > +	status = "okay";
> > +
> > +	fixed-link {
> > +		speed = <1000>;
> > +		full-duplex;
> > +	};
> > +};
> > +
> > +&factory {
> > +	compatible = "nvmem-cells";
> > +	#address-cells = <1>;
> > +	#size-cells = <1>;
> > +
> > +	macaddr_factory_0: macaddr@0 {
> > +		reg = <0x0 0x6>;
> > +	};
> > +
> > +	macaddr_factory_6: macaddr@6 {
> > +		reg = <0x6 0x6>;
> > +	};
> > +};
> > -- 
> > 2.39.1
> > 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000
  2023-02-03 17:46 ` [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000 Pali Rohár
  2023-03-29 19:39   ` Pali Rohár
@ 2023-04-07 15:24   ` Gregory CLEMENT
  1 sibling, 0 replies; 3+ messages in thread
From: Gregory CLEMENT @ 2023-04-07 15:24 UTC (permalink / raw)
  To: Pali Rohár, Andrew Lunn, devicetree, linux-arm-kernel,
	linux-kernel

Pali Rohár <pali@kernel.org> writes:

> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
>> The GL-MV1000 (Brume) is a small form-factor gateway router.
>> It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
>> 
>> Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
>> CC: Pali <pali@kernel.org>
>
> Looks good,
>
> Reviewed-by: Pali Rohár <pali@kernel.org>


Applied on mvebu/dt64

Thanks,

Gregory

>
>> ---
>>  arch/arm64/boot/dts/marvell/Makefile          |   1 +
>>  .../dts/marvell/armada-3720-gl-mv1000.dts     | 239 ++++++++++++++++++
>>  2 files changed, 240 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> 
>> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
>> index 058237681fe5..79ac09b58a89 100644
>> --- a/arch/arm64/boot/dts/marvell/Makefile
>> +++ b/arch/arm64/boot/dts/marvell/Makefile
>> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
>> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
>>  dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
>> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> new file mode 100644
>> index 000000000000..b1b45b4fa9d4
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> @@ -0,0 +1,239 @@
>> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include "armada-372x.dtsi"
>> +
>> +/ {
>> +	model = "GL.iNet GL-MV1000";
>> +	compatible = "glinet,gl-mv1000", "marvell,armada3720";
>> +
>> +	aliases {
>> +		led-boot = &led_power;
>> +		led-failsafe = &led_power;
>> +		led-running = &led_power;
>> +		led-upgrade = &led_power;
>> +	};
>> +
>> +	chosen {
>> +		stdout-path = "serial0:115200n8";
>> +	};
>> +
>> +	memory@0 {
>> +		device_type = "memory";
>> +		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
>> +	};
>> +
>> +	vcc_sd_reg1: regulator {
>> +		compatible = "regulator-gpio";
>> +		regulator-name = "vcc_sd1";
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		regulator-boot-on;
>> +
>> +		gpios-states = <0>;
>> +		states = <1800000 0x1
>> +			3300000 0x0>;
>> +		enable-active-high;
>> +	};
>> +
>> +	keys {
>> +		compatible = "gpio-keys";
>> +
>> +		reset {
>> +			label = "reset";
>> +			linux,code = <KEY_RESTART>;
>> +			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		switch {
>> +			label = "switch";
>> +			linux,code = <BTN_0>;
>> +			gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
>> +		};
>> +	};
>> +
>> +	leds {
>> +		compatible = "gpio-leds";
>> +
>> +		vpn {
>> +			label = "green:vpn";
>> +			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		wan {
>> +			label = "green:wan";
>> +			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
>> +		};
>> +
>> +		led_power: power {
>> +			label = "green:power";
>> +			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
>> +			default-state = "on";
>> +		};
>> +	};
>> +};
>> +
>> +&spi0 {
>> +	status = "okay";
>> +
>> +	flash@0 {
>> +		reg = <0>;
>> +		compatible = "jedec,spi-nor";
>> +		spi-max-frequency = <104000000>;
>> +		m25p,fast-read;
>> +		partitions {
>> +			compatible = "fixed-partitions";
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +
>> +			partition@0 {
>> +				label = "firmware";
>> +				reg = <0 0xf0000>;
>> +			};
>> +
>> +			partition@f0000 {
>> +				label = "u-boot-env";
>> +				reg = <0xf0000 0x8000>;
>> +			};
>> +
>> +			factory: partition@f8000 {
>> +				label = "factory";
>> +				reg = <0xf8000 0x8000>;
>> +				read-only;
>> +			};
>> +
>> +			partition@100000 {
>> +				label = "dtb";
>> +				reg = <0x100000 0x10000>;
>> +				read-only;
>> +			};
>> +
>> +			partition@110000 {
>> +				label = "rescue";
>> +				reg = <0x110000 0x1000000>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&sdhci1 {
>> +	wp-inverted;
>> +	bus-width = <4>;
>> +	cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
>> +	marvell,pad-type = "sd";
>> +	no-1-8-v;
>> +	vqmmc-supply = <&vcc_sd_reg1>;
>> +	status = "okay";
>> +};
>> +
>> +&sdhci0 {
>> +	bus-width = <8>;
>> +	mmc-ddr-1_8v;
>> +	mmc-hs400-1_8v;
>> +	non-removable;
>> +	no-sd;
>> +	no-sdio;
>> +	marvell,pad-type = "fixed-1-8v";
>> +	status = "okay";
>> +};
>> +
>> +&usb3 {
>> +	status = "okay";
>> +};
>> +
>> +&usb2 {
>> +	status = "okay";
>> +};
>> +
>> +&uart0 {
>> +	status = "okay";
>> +};
>> +
>> +&mdio {
>> +	switch0: switch0@1 {
>> +		compatible = "marvell,mv88e6085";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		reg = <1>;
>> +
>> +		dsa,member = <0 0>;
>> +
>> +		ports: ports {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			port@0 {
>> +				reg = <0>;
>> +				label = "cpu";
>> +				ethernet = <&eth0>;
>> +			};
>> +
>> +			port@1 {
>> +				reg = <1>;
>> +				label = "wan";
>> +				phy-handle = <&switch0phy0>;
>> +			};
>> +
>> +			port@2 {
>> +				reg = <2>;
>> +				label = "lan0";
>> +				phy-handle = <&switch0phy1>;
>> +
>> +				nvmem-cells = <&macaddr_factory_6>;
>> +				nvmem-cell-names = "mac-address";
>> +			};
>> +
>> +			port@3 {
>> +				reg = <3>;
>> +				label = "lan1";
>> +				phy-handle = <&switch0phy2>;
>> +
>> +				nvmem-cells = <&macaddr_factory_6>;
>> +				nvmem-cell-names = "mac-address";
>> +			};
>> +		};
>> +
>> +		mdio {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			switch0phy0: switch0phy0@11 {
>> +				reg = <0x11>;
>> +			};
>> +			switch0phy1: switch0phy1@12 {
>> +				reg = <0x12>;
>> +			};
>> +			switch0phy2: switch0phy2@13 {
>> +				reg = <0x13>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&eth0 {
>> +	nvmem-cells = <&macaddr_factory_0>;
>> +	nvmem-cell-names = "mac-address";
>> +	phy-mode = "rgmii-id";
>> +	status = "okay";
>> +
>> +	fixed-link {
>> +		speed = <1000>;
>> +		full-duplex;
>> +	};
>> +};
>> +
>> +&factory {
>> +	compatible = "nvmem-cells";
>> +	#address-cells = <1>;
>> +	#size-cells = <1>;
>> +
>> +	macaddr_factory_0: macaddr@0 {
>> +		reg = <0x0 0x6>;
>> +	};
>> +
>> +	macaddr_factory_6: macaddr@6 {
>> +		reg = <0x6 0x6>;
>> +	};
>> +};
>> -- 
>> 2.39.1
>> 

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2023-04-07 15:25 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
     [not found] <20230202093706.30995-1-mrkiko.rs@gmail.com>
2023-02-03 17:46 ` [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000 Pali Rohár
2023-03-29 19:39   ` Pali Rohár
2023-04-07 15:24   ` Gregory CLEMENT

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).