[PATCH 2/9] serial: digicolor-usart: Don't allow CS5-6

[PATCH 2/9] serial: digicolor-usart: Don't allow CS5-6

[Ilpo Järvinen]

Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.

Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().

Cc: Baruch Siach <baruch@tkos.co.il>
Fixes: 5930cb3511df (serial: driver for Conexant Digicolor USART)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
 drivers/tty/serial/digicolor-usart.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/tty/serial/digicolor-usart.c b/drivers/tty/serial/digicolor-usart.c
index 6d70fea76bb3..65e653eb5026 100644
--- a/drivers/tty/serial/digicolor-usart.c
+++ b/drivers/tty/serial/digicolor-usart.c
@@ -309,6 +309,8 @@ static void digicolor_uart_set_termios(struct uart_port *port,
 	case CS8:
 	default:
 		config |= UA_CONFIG_CHAR_LEN;
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
 		break;
 	}
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/9] serial: rda-uart: Don't allow CS5-6

[Ilpo Järvinen]

Only CS7 and CS8 are supported but CSIZE is not sanitized after
fallthrough from CS5 or CS6 to CS7.

Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().

Cc: Manivannan Sadhasivam <mani@kernel.org>
Fixes: c10b13325ced (tty: serial: Add RDA8810PL UART driver)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
 drivers/tty/serial/rda-uart.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/tty/serial/rda-uart.c b/drivers/tty/serial/rda-uart.c
index e5f1fded423a..f556b4955f59 100644
--- a/drivers/tty/serial/rda-uart.c
+++ b/drivers/tty/serial/rda-uart.c
@@ -262,6 +262,8 @@ static void rda_uart_set_termios(struct uart_port *port,
 		fallthrough;
 	case CS7:
 		ctrl &= ~RDA_UART_DBITS_8;
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS7;
 		break;
 	default:
 		ctrl |= RDA_UART_DBITS_8;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 7/9] serial: st-asc: Sanitize CSIZE and correct PARENB for CS7

[Ilpo Järvinen]

Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.

Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().

Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Fixes: c4b058560762 (serial:st-asc: Add ST ASC driver.)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
 drivers/tty/serial/st-asc.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/tty/serial/st-asc.c b/drivers/tty/serial/st-asc.c
index d7fd692286cf..1b0da603ab54 100644
--- a/drivers/tty/serial/st-asc.c
+++ b/drivers/tty/serial/st-asc.c
@@ -535,10 +535,14 @@ static void asc_set_termios(struct uart_port *port, struct ktermios *termios,
 	/* set character length */
 	if ((cflag & CSIZE) == CS7) {
 		ctrl_val |= ASC_CTL_MODE_7BIT_PAR;
+		cflag |= PARENB;
 	} else {
 		ctrl_val |= (cflag & PARENB) ?  ASC_CTL_MODE_8BIT_PAR :
 						ASC_CTL_MODE_8BIT;
+		cflag &= ~CSIZE;
+		cflag |= CS8;
 	}
+	termios->c_cflag = cflag;
 
 	/* set stop bit */
 	ctrl_val |= (cflag & CSTOPB) ? ASC_CTL_STOP_2BIT : ASC_CTL_STOP_1BIT;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 8/9] serial: stm32-usart: Correct CSIZE, bits, and parity

[Ilpo Järvinen]

Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.

Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().

Cc: Erwan Le Ray <erwan.leray@st.com>
Fixes: c8a9d043947b (serial: stm32: fix word length configuration)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
 drivers/tty/serial/stm32-usart.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 87b5cd4c9743..3c551fd4f3ff 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -1037,13 +1037,22 @@ static void stm32_usart_set_termios(struct uart_port *port,
 	 * CS8 or (CS7 + parity), 8 bits word aka [M1:M0] = 0b00
 	 * M0 and M1 already cleared by cr1 initialization.
 	 */
-	if (bits == 9)
+	if (bits == 9) {
 		cr1 |= USART_CR1_M0;
-	else if ((bits == 7) && cfg->has_7bits_data)
+	} else if ((bits == 7) && cfg->has_7bits_data) {
 		cr1 |= USART_CR1_M1;
-	else if (bits != 8)
+	} else if (bits != 8) {
 		dev_dbg(port->dev, "Unsupported data bits config: %u bits\n"
 			, bits);
+		cflag &= ~CSIZE;
+		cflag |= CS8;
+		termios->c_cflag = cflag;
+		bits = 8;
+		if (cflag & PARENB) {
+			bits++;
+			cr1 |= USART_CR1_M0;
+		}
+	}
 
 	if (ofs->rtor != UNDEF_REG && (stm32_port->rx_ch ||
 				       (stm32_port->fifoen &&
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/9] serial: digicolor-usart: Don't allow CS5-6

[Baruch Siach]

Hi Ilpo,

On Tue, May 17 2022, Ilpo Järvinen wrote:
> Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
> the default: block.
>
> Set CSIZE correctly so that userspace knows the effective value.
> Incorrect CSIZE also results in miscalculation of the frame bits in
> tty_get_char_size() or in its predecessor where the roughly the same
> code is directly within uart_update_timeout().
>
> Cc: Baruch Siach <baruch@tkos.co.il>
> Fixes: 5930cb3511df (serial: driver for Conexant Digicolor USART)
> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

Acked-by: Baruch Siach <baruch@tkos.co.il>

Thanks,
baruch

> ---
>  drivers/tty/serial/digicolor-usart.c | 2 ++
>  1 file changed, 2 insertions(+)
>
> diff --git a/drivers/tty/serial/digicolor-usart.c b/drivers/tty/serial/digicolor-usart.c
> index 6d70fea76bb3..65e653eb5026 100644
> --- a/drivers/tty/serial/digicolor-usart.c
> +++ b/drivers/tty/serial/digicolor-usart.c
> @@ -309,6 +309,8 @@ static void digicolor_uart_set_termios(struct uart_port *port,
>  	case CS8:
>  	default:
>  		config |= UA_CONFIG_CHAR_LEN;
> +		termios->c_cflag &= ~CSIZE;
> +		termios->c_cflag |= CS8;
>  		break;
>  	}


-- 
                                                     ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel