* Re: [PATCH 0/2] arm64: dts: a7k: add COM Express boards [not found] <20260122165923.2316510-1-enachman@marvell.com> @ 2026-01-22 18:07 ` Rob Herring 2026-01-23 9:10 ` Gregory CLEMENT [not found] ` <20260122165923.2316510-2-enachman@marvell.com> 1 sibling, 1 reply; 10+ messages in thread From: Rob Herring @ 2026-01-22 18:07 UTC (permalink / raw) To: Elad Nachman Cc: conor+dt, linux-kernel, robh+dt, chris.packham, pali, andrew, devicetree, mrkiko.rs, sebastian.hesselbarth, linux-arm-kernel, gregory.clement, krzysztof.kozlowski+dt On Thu, 22 Jan 2026 18:59:20 +0200, Elad Nachman wrote: > From: Elad Nachman <enachman@marvell.com> > > Add support for Armada 7020 Express Type 7 CPU module board by Marvell. > Add device tree bindings for this board. > Define this COM Express CPU module as dtsi and provide a dtsi file for > the carrier board (Marvell DB-98CX85x0 COM Express type 7 carrier board). > Add the Falcon DB to the MAINTAINERS list > > Since memory is soldered on CPU module, memory node is on CPU module > dtsi file. > > This Carrier board only utilizes the PCIe link, hence no special device > or driver support is provided by this dtsi file. > Devise a dts file for the combined com express carrier and CPU module. > > The Aramda 7020 CPU COM Express board offers the following features: > > 1. Armada 7020 CPU, with dual ARM A72 cores > 2. DDR4 memory, 8GB, on board soldered > 3. 1Gbit Out of Band Ethernet via RGMII to PHY and RJ45 connector, > all are present on A7K CPU module (none on the carrier) > 4. Optional 10G KR Ethernet going via the COM Express type 7 connector > 5. On-board 8 Gbit, 8-bit bus width NAND flash > 6. On-board 512 Mbit SPI flash > 7. PCIe Root Complex, 4 lanes PCIe gen3 connectivity, going via the > COM Express type 7 connector > 8. m.2 SATA connector > 9. Micro-SD card connector > 10. USB 2.0 via COM Express type 7 connector > 11. Two i2c interfaces - one to the CPU module, and one to the > carrier board via the COM Express type 7 connector > 12. UART (mini USB connector by virtue of FT2232D UART to USB > converter, connected to the Armada 7020 UART0) > > Elad Nachman (3): > dt-bindings: arm64: add Marvell 7k COMe boards > arm64: dts: a7k: add COM Express boards > MAINTAINERS: Add Falcon DB > > .../bindings/arm/marvell/armada-7k-8k.yaml | 11 ++ > MAINTAINERS | 1 + > arch/arm64/boot/dts/marvell/Makefile | 1 + > .../dts/marvell/armada-7020-comexpress.dtsi | 161 ++++++++++++++++++ > arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 7 + > .../boot/dts/marvell/armada-ap806-dual.dtsi | 4 +- > .../dts/marvell/db-falcon-carrier-a7k.dts | 27 +++ > .../boot/dts/marvell/db-falcon-carrier.dtsi | 22 +++ > 8 files changed, 232 insertions(+), 2 deletions(-) > create mode 100644 arch/arm64/boot/dts/marvell/armada-7020-comexpress.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dts > create mode 100644 arch/arm64/boot/dts/marvell/db-falcon-carrier.dtsi > > -- > 2.25.1 > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade This patch series was applied (using b4) to base: Base: attempting to guess base-commit... Base: tags/next-20260121 (exact match) Base: tags/next-20260121 (use --merge-base to override) If this is not the correct base, please add 'base-commit' tag (or use b4 which does this automatically) New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/marvell/' for 20260122165923.2316510-1-enachman@marvell.com: arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dtb: ethernet@0 (marvell,armada-7k-pp22): ethernet-port@0:phy-mode:0: '10gbase-kr' is not one of ['gmii', 'sgmii', 'rgmii-id', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', '10gbase-r'] from schema $id: http://devicetree.org/schemas/net/marvell,pp2.yaml ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: dts: a7k: add COM Express boards 2026-01-22 18:07 ` [PATCH 0/2] arm64: dts: a7k: add COM Express boards Rob Herring @ 2026-01-23 9:10 ` Gregory CLEMENT 2026-01-23 9:20 ` Maxime Chevallier 0 siblings, 1 reply; 10+ messages in thread From: Gregory CLEMENT @ 2026-01-23 9:10 UTC (permalink / raw) To: Rob Herring, Elad Nachman, andrew, Maxime Chevallier Cc: conor+dt, linux-kernel, robh+dt, chris.packham, pali, devicetree, mrkiko.rs, sebastian.hesselbarth, linux-arm-kernel, krzysztof.kozlowski+dt Hello, > On Thu, 22 Jan 2026 18:59:20 +0200, Elad Nachman wrote: >> From: Elad Nachman <enachman@marvell.com> >> >> Add support for Armada 7020 Express Type 7 CPU module board by Marvell. >> Add device tree bindings for this board. >> Define this COM Express CPU module as dtsi and provide a dtsi file for >> the carrier board (Marvell DB-98CX85x0 COM Express type 7 carrier board). >> Add the Falcon DB to the MAINTAINERS list >> >> Since memory is soldered on CPU module, memory node is on CPU module >> dtsi file. >> >> This Carrier board only utilizes the PCIe link, hence no special device >> or driver support is provided by this dtsi file. >> Devise a dts file for the combined com express carrier and CPU module. >> >> The Aramda 7020 CPU COM Express board offers the following features: >> >> 1. Armada 7020 CPU, with dual ARM A72 cores >> 2. DDR4 memory, 8GB, on board soldered >> 3. 1Gbit Out of Band Ethernet via RGMII to PHY and RJ45 connector, >> all are present on A7K CPU module (none on the carrier) >> 4. Optional 10G KR Ethernet going via the COM Express type 7 connector >> 5. On-board 8 Gbit, 8-bit bus width NAND flash >> 6. On-board 512 Mbit SPI flash >> 7. PCIe Root Complex, 4 lanes PCIe gen3 connectivity, going via the >> COM Express type 7 connector >> 8. m.2 SATA connector >> 9. Micro-SD card connector >> 10. USB 2.0 via COM Express type 7 connector >> 11. Two i2c interfaces - one to the CPU module, and one to the >> carrier board via the COM Express type 7 connector >> 12. UART (mini USB connector by virtue of FT2232D UART to USB >> converter, connected to the Armada 7020 UART0) >> >> Elad Nachman (3): >> dt-bindings: arm64: add Marvell 7k COMe boards >> arm64: dts: a7k: add COM Express boards >> MAINTAINERS: Add Falcon DB >> >> .../bindings/arm/marvell/armada-7k-8k.yaml | 11 ++ >> MAINTAINERS | 1 + >> arch/arm64/boot/dts/marvell/Makefile | 1 + >> .../dts/marvell/armada-7020-comexpress.dtsi | 161 ++++++++++++++++++ >> arch/arm64/boot/dts/marvell/armada-70x0.dtsi | 7 + >> .../boot/dts/marvell/armada-ap806-dual.dtsi | 4 +- >> .../dts/marvell/db-falcon-carrier-a7k.dts | 27 +++ >> .../boot/dts/marvell/db-falcon-carrier.dtsi | 22 +++ >> 8 files changed, 232 insertions(+), 2 deletions(-) >> create mode 100644 arch/arm64/boot/dts/marvell/armada-7020-comexpress.dtsi >> create mode 100644 arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dts >> create mode 100644 arch/arm64/boot/dts/marvell/db-falcon-carrier.dtsi >> >> -- >> 2.25.1 >> >> >> > > > My bot found new DTB warnings on the .dts files added or changed in this > series. > > Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings > are fixed by another series. Ultimately, it is up to the platform > maintainer whether these warnings are acceptable or not. No need to reply > unless the platform maintainer has comments. > > If you already ran DT checks and didn't see these error(s), then > make sure dt-schema is up to date: > > pip3 install dtschema --upgrade > > > This patch series was applied (using b4) to base: > Base: attempting to guess base-commit... > Base: tags/next-20260121 (exact match) > Base: tags/next-20260121 (use --merge-base to override) > > If this is not the correct base, please add 'base-commit' tag > (or use b4 which does this automatically) > > > New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/marvell/' for 20260122165923.2316510-1-enachman@marvell.com: > > arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dtb: ethernet@0 (marvell,armada-7k-pp22): ethernet-port@0:phy-mode:0: '10gbase-kr' is not one of ['gmii', 'sgmii', 'rgmii-id', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', '10gbase-r'] > from schema $id: > http://devicetree.org/schemas/net/marvell,pp2.yaml Does this mean we should add 10gbase-kr to the phy-mode enum list in Documentation/devicetree/bindings/net/marvell? Adding it would likely resolve the warning, but I’m not sure if it’s the correct approach from the driver’s perspective. That’s why I’ve included Andrew in the To field and added Maxime as well. Regards, Gregory > -- Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: dts: a7k: add COM Express boards 2026-01-23 9:10 ` Gregory CLEMENT @ 2026-01-23 9:20 ` Maxime Chevallier 2026-01-23 9:27 ` Gregory CLEMENT 0 siblings, 1 reply; 10+ messages in thread From: Maxime Chevallier @ 2026-01-23 9:20 UTC (permalink / raw) To: Gregory CLEMENT, Rob Herring, Elad Nachman, andrew Cc: conor+dt, linux-kernel, robh+dt, chris.packham, pali, devicetree, mrkiko.rs, sebastian.hesselbarth, linux-arm-kernel, krzysztof.kozlowski+dt Hi, On 23/01/2026 10:10, Gregory CLEMENT wrote: > Hello, > >> On Thu, 22 Jan 2026 18:59:20 +0200, Elad Nachman wrote: >>> From: Elad Nachman <enachman@marvell.com> >>> >>> Add support for Armada 7020 Express Type 7 CPU module board by Marvell. >>> Add device tree bindings for this board. >>> Define this COM Express CPU module as dtsi and provide a dtsi file for >>> the carrier board (Marvell DB-98CX85x0 COM Express type 7 carrier board). >>> Add the Falcon DB to the MAINTAINERS list >>> >>> Since memory is soldered on CPU module, memory node is on CPU module >>> dtsi file. >>> >>> This Carrier board only utilizes the PCIe link, hence no special device >>> or driver support is provided by this dtsi file. >>> Devise a dts file for the combined com express carrier and CPU module. >>> >>> The Aramda 7020 CPU COM Express board offers the following features: >>> >>> 1. Armada 7020 CPU, with dual ARM A72 cores >>> 2. DDR4 memory, 8GB, on board soldered >>> 3. 1Gbit Out of Band Ethernet via RGMII to PHY and RJ45 connector, >>> all are present on A7K CPU module (none on the carrier) >>> 4. Optional 10G KR Ethernet going via the COM Express type 7 connector >>> 5. On-board 8 Gbit, 8-bit bus width NAND flash >>> 6. On-board 512 Mbit SPI flash >>> 7. PCIe Root Complex, 4 lanes PCIe gen3 connectivity, going via the >>> COM Express type 7 connector >>> 8. m.2 SATA connector >>> 9. Micro-SD card connector >>> 10. USB 2.0 via COM Express type 7 connector >>> 11. Two i2c interfaces - one to the CPU module, and one to the >>> carrier board via the COM Express type 7 connector >>> 12. UART (mini USB connector by virtue of FT2232D UART to USB >>> converter, connected to the Armada 7020 UART0) >>> [...] >> My bot found new DTB warnings on the .dts files added or changed in this >> series. >> >> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings >> are fixed by another series. Ultimately, it is up to the platform >> maintainer whether these warnings are acceptable or not. No need to reply >> unless the platform maintainer has comments. >> >> If you already ran DT checks and didn't see these error(s), then >> make sure dt-schema is up to date: >> >> pip3 install dtschema --upgrade >> >> >> This patch series was applied (using b4) to base: >> Base: attempting to guess base-commit... >> Base: tags/next-20260121 (exact match) >> Base: tags/next-20260121 (use --merge-base to override) >> >> If this is not the correct base, please add 'base-commit' tag >> (or use b4 which does this automatically) >> >> >> New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/marvell/' for 20260122165923.2316510-1-enachman@marvell.com: >> >> arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dtb: ethernet@0 (marvell,armada-7k-pp22): ethernet-port@0:phy-mode:0: '10gbase-kr' is not one of ['gmii', 'sgmii', 'rgmii-id', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', '10gbase-r'] >> from schema $id: >> http://devicetree.org/schemas/net/marvell,pp2.yaml > > Does this mean we should add 10gbase-kr to the phy-mode enum list in > Documentation/devicetree/bindings/net/marvell? No, 10gbase-kr is legacy, one should use "10gbase-r" instead, cf commit e0f909bc3a24 ("net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKR") That should probably be documented in the bindings at some point :) Maxime ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: dts: a7k: add COM Express boards 2026-01-23 9:20 ` Maxime Chevallier @ 2026-01-23 9:27 ` Gregory CLEMENT 2026-01-27 16:23 ` Rob Herring 0 siblings, 1 reply; 10+ messages in thread From: Gregory CLEMENT @ 2026-01-23 9:27 UTC (permalink / raw) To: Maxime Chevallier, Rob Herring, Elad Nachman, andrew Cc: conor+dt, linux-kernel, robh+dt, chris.packham, pali, devicetree, mrkiko.rs, sebastian.hesselbarth, linux-arm-kernel, krzysztof.kozlowski+dt > Hi, > > On 23/01/2026 10:10, Gregory CLEMENT wrote: >> Hello, >> >>> On Thu, 22 Jan 2026 18:59:20 +0200, Elad Nachman wrote: >>>> From: Elad Nachman <enachman@marvell.com> >>>> >>>> Add support for Armada 7020 Express Type 7 CPU module board by Marvell. >>>> Add device tree bindings for this board. >>>> Define this COM Express CPU module as dtsi and provide a dtsi file for >>>> the carrier board (Marvell DB-98CX85x0 COM Express type 7 carrier board). >>>> Add the Falcon DB to the MAINTAINERS list >>>> >>>> Since memory is soldered on CPU module, memory node is on CPU module >>>> dtsi file. >>>> >>>> This Carrier board only utilizes the PCIe link, hence no special device >>>> or driver support is provided by this dtsi file. >>>> Devise a dts file for the combined com express carrier and CPU module. >>>> >>>> The Aramda 7020 CPU COM Express board offers the following features: >>>> >>>> 1. Armada 7020 CPU, with dual ARM A72 cores >>>> 2. DDR4 memory, 8GB, on board soldered >>>> 3. 1Gbit Out of Band Ethernet via RGMII to PHY and RJ45 connector, >>>> all are present on A7K CPU module (none on the carrier) >>>> 4. Optional 10G KR Ethernet going via the COM Express type 7 connector >>>> 5. On-board 8 Gbit, 8-bit bus width NAND flash >>>> 6. On-board 512 Mbit SPI flash >>>> 7. PCIe Root Complex, 4 lanes PCIe gen3 connectivity, going via the >>>> COM Express type 7 connector >>>> 8. m.2 SATA connector >>>> 9. Micro-SD card connector >>>> 10. USB 2.0 via COM Express type 7 connector >>>> 11. Two i2c interfaces - one to the CPU module, and one to the >>>> carrier board via the COM Express type 7 connector >>>> 12. UART (mini USB connector by virtue of FT2232D UART to USB >>>> converter, connected to the Armada 7020 UART0) >>>> > > [...] > >>> My bot found new DTB warnings on the .dts files added or changed in this >>> series. >>> >>> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings >>> are fixed by another series. Ultimately, it is up to the platform >>> maintainer whether these warnings are acceptable or not. No need to reply >>> unless the platform maintainer has comments. >>> >>> If you already ran DT checks and didn't see these error(s), then >>> make sure dt-schema is up to date: >>> >>> pip3 install dtschema --upgrade >>> >>> >>> This patch series was applied (using b4) to base: >>> Base: attempting to guess base-commit... >>> Base: tags/next-20260121 (exact match) >>> Base: tags/next-20260121 (use --merge-base to override) >>> >>> If this is not the correct base, please add 'base-commit' tag >>> (or use b4 which does this automatically) >>> >>> >>> New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/marvell/' for 20260122165923.2316510-1-enachman@marvell.com: >>> >>> arch/arm64/boot/dts/marvell/db-falcon-carrier-a7k.dtb: ethernet@0 (marvell,armada-7k-pp22): ethernet-port@0:phy-mode:0: '10gbase-kr' is not one of ['gmii', 'sgmii', 'rgmii-id', '1000base-x', '2500base-x', '5gbase-r', 'rxaui', '10gbase-r'] >>> from schema $id: >>> http://devicetree.org/schemas/net/marvell,pp2.yaml >> >> Does this mean we should add 10gbase-kr to the phy-mode enum list in >> Documentation/devicetree/bindings/net/marvell? > > No, 10gbase-kr is legacy, one should use "10gbase-r" instead, cf commit > > e0f909bc3a24 ("net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKR") > > That should probably be documented in the bindings at some point :) Thanks, Maxime! Elad, I’ll amend the commit unless you have a strong reason against it. Gregory > > Maxime -- Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 0/2] arm64: dts: a7k: add COM Express boards 2026-01-23 9:27 ` Gregory CLEMENT @ 2026-01-27 16:23 ` Rob Herring 0 siblings, 0 replies; 10+ messages in thread From: Rob Herring @ 2026-01-27 16:23 UTC (permalink / raw) To: Gregory CLEMENT Cc: Maxime Chevallier, Elad Nachman, andrew, conor+dt, linux-kernel, chris.packham, pali, devicetree, mrkiko.rs, sebastian.hesselbarth, linux-arm-kernel, krzysztof.kozlowski+dt On Fri, Jan 23, 2026 at 3:27 AM Gregory CLEMENT <gregory.clement@bootlin.com> wrote: > > > > Hi, > > > > On 23/01/2026 10:10, Gregory CLEMENT wrote: > >> Hello, > >> > >>> On Thu, 22 Jan 2026 18:59:20 +0200, Elad Nachman wrote: > >>>> From: Elad Nachman <enachman@marvell.com> > >>>> > >>>> Add support for Armada 7020 Express Type 7 CPU module board by Marvell. > >>>> Add device tree bindings for this board. > >>>> Define this COM Express CPU module as dtsi and provide a dtsi file for > >>>> the carrier board (Marvell DB-98CX85x0 COM Express type 7 carrier board). > >>>> Add the Falcon DB to the MAINTAINERS list > >>>> > >>>> Since memory is soldered on CPU module, memory node is on CPU module > >>>> dtsi file. > >>>> > >>>> This Carrier board only utilizes the PCIe link, hence no special device > >>>> or driver support is provided by this dtsi file. > >>>> Devise a dts file for the combined com express carrier and CPU module. > >>>> > >>>> The Aramda 7020 CPU COM Express board offers the following features: > >>>> > >>>> 1. Armada 7020 CPU, with dual ARM A72 cores > >>>> 2. DDR4 memory, 8GB, on board soldered > >>>> 3. 1Gbit Out of Band Ethernet via RGMII to PHY and RJ45 connector, > >>>> all are present on A7K CPU module (none on the carrier) > >>>> 4. Optional 10G KR Ethernet going via the COM Express type 7 connector > >>>> 5. On-board 8 Gbit, 8-bit bus width NAND flash > >>>> 6. On-board 512 Mbit SPI flash > >>>> 7. PCIe Root Complex, 4 lanes PCIe gen3 connectivity, going via the > >>>> COM Express type 7 connector > >>>> 8. m.2 SATA connector > >>>> 9. Micro-SD card connector > >>>> 10. USB 2.0 via COM Express type 7 connector > >>>> 11. Two i2c interfaces - one to the CPU module, and one to the > >>>> carrier board via the COM Express type 7 connector > >>>> 12. UART (mini USB connector by virtue of FT2232D UART to USB > >>>> converter, connected to the Armada 7020 UART0) > >>>> > > > > [...] > >> > >> Does this mean we should add 10gbase-kr to the phy-mode enum list in > >> Documentation/devicetree/bindings/net/marvell? > > > > No, 10gbase-kr is legacy, one should use "10gbase-r" instead, cf commit > > > > e0f909bc3a24 ("net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKR") > > > > That should probably be documented in the bindings at some point :) > > Thanks, Maxime! > > Elad, I’ll amend the commit unless you have a strong reason against it. You applied the .dts, but not the binding. So now more warnings... Please apply the binding too. Rob ^ permalink raw reply [flat|nested] 10+ messages in thread
[parent not found: <20260122165923.2316510-2-enachman@marvell.com>]
* Re: [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards [not found] ` <20260122165923.2316510-2-enachman@marvell.com> @ 2026-01-22 23:21 ` Rob Herring (Arm) 2026-03-02 15:43 ` Gregory CLEMENT 2026-03-13 15:49 ` Gregory CLEMENT 2 siblings, 0 replies; 10+ messages in thread From: Rob Herring (Arm) @ 2026-01-22 23:21 UTC (permalink / raw) To: Elad Nachman Cc: chris.packham, linux-kernel, krzysztof.kozlowski+dt, linux-arm-kernel, pali, mrkiko.rs, devicetree, robh+dt, andrew, gregory.clement, conor+dt, sebastian.hesselbarth On Thu, 22 Jan 2026 18:59:21 +0200, Elad Nachman wrote: > From: Elad Nachman <enachman@marvell.com> > > Add dt bindings for: > Armada 7020 COM Express CPU module > Falcon DB-98CX85x0 COM Express type 7 Carrier board > Falcon DB-98CX85x0 COM Express type 7 Carrier board > with an Armada 7020 COM Express CPU module > > Signed-off-by: Elad Nachman <enachman@marvell.com> > --- > .../devicetree/bindings/arm/marvell/armada-7k-8k.yaml | 11 +++++++++++ > 1 file changed, 11 insertions(+) > Acked-by: Rob Herring (Arm) <robh@kernel.org> ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards [not found] ` <20260122165923.2316510-2-enachman@marvell.com> 2026-01-22 23:21 ` [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards Rob Herring (Arm) @ 2026-03-02 15:43 ` Gregory CLEMENT 2026-03-06 23:46 ` Rob Herring 2026-03-13 15:49 ` Gregory CLEMENT 2 siblings, 1 reply; 10+ messages in thread From: Gregory CLEMENT @ 2026-03-02 15:43 UTC (permalink / raw) To: Elad Nachman, robh+dt, krzysztof.kozlowski+dt, conor+dt, andrew, sebastian.hesselbarth, pali, mrkiko.rs, chris.packham, devicetree, linux-kernel, linux-arm-kernel Cc: enachman Elad Nachman <enachman@marvell.com> writes: > From: Elad Nachman <enachman@marvell.com> > > Add dt bindings for: > Armada 7020 COM Express CPU module > Falcon DB-98CX85x0 COM Express type 7 Carrier board > Falcon DB-98CX85x0 COM Express type 7 Carrier board > with an Armada 7020 COM Express CPU module > > Signed-off-by: Elad Nachman <enachman@marvell.com> Applied on mvebu/dt64 Thanks, Gregory > --- > .../devicetree/bindings/arm/marvell/armada-7k-8k.yaml | 11 +++++++++++ > 1 file changed, 11 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > index 4bc7454a5d3a..7e77310da626 100644 > --- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > @@ -21,6 +21,17 @@ properties: > - const: marvell,armada-ap806-dual > - const: marvell,armada-ap806 > > + - description: > + Falcon (DB-98CX85x0) Development board COM Express Carrier plus > + Armada 7020 SoC COM Express CPU module > + items: > + - const: marvell,armada7020-falcon-carrier > + - const: marvell,db-falcon-carrier > + - const: marvell,armada7020-cpu-module > + - const: marvell,armada7020 > + - const: marvell,armada-ap806-dual > + - const: marvell,armada-ap806 > + > - description: Armada 7040 SoC > items: > - enum: > -- > 2.25.1 > -- Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards 2026-03-02 15:43 ` Gregory CLEMENT @ 2026-03-06 23:46 ` Rob Herring 2026-03-13 15:49 ` Gregory CLEMENT 0 siblings, 1 reply; 10+ messages in thread From: Rob Herring @ 2026-03-06 23:46 UTC (permalink / raw) To: Gregory CLEMENT Cc: Elad Nachman, krzysztof.kozlowski+dt, conor+dt, andrew, sebastian.hesselbarth, pali, mrkiko.rs, chris.packham, devicetree, linux-kernel, linux-arm-kernel On Mon, Mar 2, 2026 at 9:44 AM Gregory CLEMENT <gregory.clement@bootlin.com> wrote: > > Elad Nachman <enachman@marvell.com> writes: > > > From: Elad Nachman <enachman@marvell.com> > > > > Add dt bindings for: > > Armada 7020 COM Express CPU module > > Falcon DB-98CX85x0 COM Express type 7 Carrier board > > Falcon DB-98CX85x0 COM Express type 7 Carrier board > > with an Armada 7020 COM Express CPU module > > > > Signed-off-by: Elad Nachman <enachman@marvell.com> > > Applied on mvebu/dt64 It seems the .dts files are in 7.0 and the binding is only in next. The binding needs to go into 7.0 too. Please pay attention to the warnings. There are only 19 (unique ones) left for marvell since I fixed most of them. Rob ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards 2026-03-06 23:46 ` Rob Herring @ 2026-03-13 15:49 ` Gregory CLEMENT 0 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2026-03-13 15:49 UTC (permalink / raw) To: Rob Herring Cc: Elad Nachman, krzysztof.kozlowski+dt, conor+dt, andrew, sebastian.hesselbarth, pali, mrkiko.rs, chris.packham, devicetree, linux-kernel, linux-arm-kernel Hello Rob, > On Mon, Mar 2, 2026 at 9:44 AM Gregory CLEMENT > <gregory.clement@bootlin.com> wrote: >> >> Elad Nachman <enachman@marvell.com> writes: >> >> > From: Elad Nachman <enachman@marvell.com> >> > >> > Add dt bindings for: >> > Armada 7020 COM Express CPU module >> > Falcon DB-98CX85x0 COM Express type 7 Carrier board >> > Falcon DB-98CX85x0 COM Express type 7 Carrier board >> > with an Armada 7020 COM Express CPU module >> > >> > Signed-off-by: Elad Nachman <enachman@marvell.com> >> >> Applied on mvebu/dt64 > > It seems the .dts files are in 7.0 and the binding is only in next. > The binding needs to go into 7.0 too. > > Please pay attention to the warnings. There are only 19 (unique ones) > left for marvell since I fixed most of them. > Sorry for this. I have now applied the binding, and it will be included in my next fixes PR. Gregory > Rob -- Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards [not found] ` <20260122165923.2316510-2-enachman@marvell.com> 2026-01-22 23:21 ` [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards Rob Herring (Arm) 2026-03-02 15:43 ` Gregory CLEMENT @ 2026-03-13 15:49 ` Gregory CLEMENT 2 siblings, 0 replies; 10+ messages in thread From: Gregory CLEMENT @ 2026-03-13 15:49 UTC (permalink / raw) To: Elad Nachman, robh+dt, krzysztof.kozlowski+dt, conor+dt, andrew, sebastian.hesselbarth, pali, mrkiko.rs, chris.packham, devicetree, linux-kernel, linux-arm-kernel Cc: enachman Elad Nachman <enachman@marvell.com> writes: > From: Elad Nachman <enachman@marvell.com> > > Add dt bindings for: > Armada 7020 COM Express CPU module > Falcon DB-98CX85x0 COM Express type 7 Carrier board > Falcon DB-98CX85x0 COM Express type 7 Carrier board > with an Armada 7020 COM Express CPU module > > Signed-off-by: Elad Nachman <enachman@marvell.com> Applied on mvebu/fixes Thanks, Gregory > --- > .../devicetree/bindings/arm/marvell/armada-7k-8k.yaml | 11 +++++++++++ > 1 file changed, 11 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > index 4bc7454a5d3a..7e77310da626 100644 > --- a/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > +++ b/Documentation/devicetree/bindings/arm/marvell/armada-7k-8k.yaml > @@ -21,6 +21,17 @@ properties: > - const: marvell,armada-ap806-dual > - const: marvell,armada-ap806 > > + - description: > + Falcon (DB-98CX85x0) Development board COM Express Carrier plus > + Armada 7020 SoC COM Express CPU module > + items: > + - const: marvell,armada7020-falcon-carrier > + - const: marvell,db-falcon-carrier > + - const: marvell,armada7020-cpu-module > + - const: marvell,armada7020 > + - const: marvell,armada-ap806-dual > + - const: marvell,armada-ap806 > + > - description: Armada 7040 SoC > items: > - enum: > -- > 2.25.1 > -- Grégory CLEMENT, Bootlin Embedded Linux and Kernel engineering https://bootlin.com ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2026-03-13 15:49 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20260122165923.2316510-1-enachman@marvell.com>
2026-01-22 18:07 ` [PATCH 0/2] arm64: dts: a7k: add COM Express boards Rob Herring
2026-01-23 9:10 ` Gregory CLEMENT
2026-01-23 9:20 ` Maxime Chevallier
2026-01-23 9:27 ` Gregory CLEMENT
2026-01-27 16:23 ` Rob Herring
[not found] ` <20260122165923.2316510-2-enachman@marvell.com>
2026-01-22 23:21 ` [PATCH 1/3] dt-bindings: arm64: add Marvell 7k COMe boards Rob Herring (Arm)
2026-03-02 15:43 ` Gregory CLEMENT
2026-03-06 23:46 ` Rob Herring
2026-03-13 15:49 ` Gregory CLEMENT
2026-03-13 15:49 ` Gregory CLEMENT
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox