[PATCH 0/3] drm/rockchip: Add driver for the new DSI2 controller

[PATCH 0/3] drm/rockchip: Add driver for the new DSI2 controller

[Heiko Stuebner]

This series adds a bridge and glue driver for the DSI2 controller found
in the rk3588 soc from Rockchip, that is based on a Synopsis IP block.

As the manual states:
The Display Serial Interface 2 (DSI-2) is part of a group of communication
protocols defined by the MIPI Alliance. The MIPI DSI-2 Host Controller is
a digital core that implements all protocol functions defined in the
MIPI DSI-2 Specification.


While the driver structure is very similar to the previous DSI controller,
the programming model of the core is quite different, with a completely
new register set.

Another notable difference is that the phy interface is variable now too
in its width and some other settings.


Heiko Stuebner (3):
  drm/bridge/synopsys: Add MIPI DSI2 host controller bridge
  dt-bindings: display: rockchip: Add schema for RK3588 DW DSI2
    controller
  drm/rockchip: Add MIPI DSI2 glue driver for RK3588

 .../rockchip/rockchip,rk3588-mipi-dsi2.yaml   |  119 ++
 drivers/gpu/drm/bridge/synopsys/Kconfig       |    6 +
 drivers/gpu/drm/bridge/synopsys/Makefile      |    1 +
 .../gpu/drm/bridge/synopsys/dw-mipi-dsi2.c    | 1034 +++++++++++++++++
 drivers/gpu/drm/rockchip/Kconfig              |   10 +
 drivers/gpu/drm/rockchip/Makefile             |    1 +
 .../gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c  |  524 +++++++++
 drivers/gpu/drm/rockchip/rockchip_drm_drv.c   |    2 +
 drivers/gpu/drm/rockchip/rockchip_drm_drv.h   |    1 +
 include/drm/bridge/dw_mipi_dsi2.h             |   94 ++
 10 files changed, 1792 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
 create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
 create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
 create mode 100644 include/drm/bridge/dw_mipi_dsi2.h

-- 
2.45.2

[PATCH 1/3] drm/bridge/synopsys: Add MIPI DSI2 host controller bridge

[Heiko Stuebner]

From: Heiko Stuebner <heiko.stuebner@cherry.de>

Add a Synopsys Designware MIPI DSI host DRM bridge driver for their
DSI2 host controller, based on the Rockchip version from the driver
rockchip/dw-mipi-dsi2.c in their vendor-kernel with phy & bridge APIs.

While the driver is heavily modelled after the previous IP, the register
set of this DSI2 controller is completely different and there are also
additional properties like the variable-width phy interface.

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 drivers/gpu/drm/bridge/synopsys/Kconfig       |    6 +
 drivers/gpu/drm/bridge/synopsys/Makefile      |    1 +
 .../gpu/drm/bridge/synopsys/dw-mipi-dsi2.c    | 1034 +++++++++++++++++
 include/drm/bridge/dw_mipi_dsi2.h             |   94 ++
 4 files changed, 1135 insertions(+)
 create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
 create mode 100644 include/drm/bridge/dw_mipi_dsi2.h

diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
index ca416dab156d..f3ab2f985f8c 100644
--- a/drivers/gpu/drm/bridge/synopsys/Kconfig
+++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
@@ -59,3 +59,9 @@ config DRM_DW_MIPI_DSI
 	select DRM_KMS_HELPER
 	select DRM_MIPI_DSI
 	select DRM_PANEL_BRIDGE
+
+config DRM_DW_MIPI_DSI2
+	tristate
+	select DRM_KMS_HELPER
+	select DRM_MIPI_DSI
+	select DRM_PANEL_BRIDGE
diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
index 9869d9651ed1..9dc376d220ad 100644
--- a/drivers/gpu/drm/bridge/synopsys/Makefile
+++ b/drivers/gpu/drm/bridge/synopsys/Makefile
@@ -8,3 +8,4 @@ obj-$(CONFIG_DRM_DW_HDMI_CEC) += dw-hdmi-cec.o
 obj-$(CONFIG_DRM_DW_HDMI_QP) += dw-hdmi-qp.o
 
 obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
+obj-$(CONFIG_DRM_DW_MIPI_DSI2) += dw-mipi-dsi2.o
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
new file mode 100644
index 000000000000..43738fe3cb93
--- /dev/null
+++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
@@ -0,0 +1,1034 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2024, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Modified by Heiko Stuebner <heiko.stuebner@cherry.de>
+ * This generic Synopsys DesignWare MIPI DSI2 host driver is based on the
+ * Rockchip version from rockchip/dw-mipi-dsi2.c converted to use bridge APIs.
+ */
+
+#include <linux/clk.h>
+#include <linux/iopoll.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/bridge/dw_mipi_dsi2.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_print.h>
+
+#define UPDATE(v, h, l)			(((v) << (l)) & GENMASK((h), (l)))
+
+#define DSI2_PWR_UP			0x000c
+#define RESET				0
+#define POWER_UP			BIT(0)
+#define CMD_TX_MODE(x)			UPDATE(x,  24,  24)
+#define DSI2_SOFT_RESET			0x0010
+#define SYS_RSTN			BIT(2)
+#define PHY_RSTN			BIT(1)
+#define IPI_RSTN			BIT(0)
+#define INT_ST_MAIN			0x0014
+#define DSI2_MODE_CTRL			0x0018
+#define DSI2_MODE_STATUS		0x001c
+#define DSI2_CORE_STATUS		0x0020
+#define PRI_RD_DATA_AVAIL		BIT(26)
+#define PRI_FIFOS_NOT_EMPTY		BIT(25)
+#define PRI_BUSY			BIT(24)
+#define CRI_RD_DATA_AVAIL		BIT(18)
+#define CRT_FIFOS_NOT_EMPTY		BIT(17)
+#define CRI_BUSY			BIT(16)
+#define IPI_FIFOS_NOT_EMPTY		BIT(9)
+#define IPI_BUSY			BIT(8)
+#define CORE_FIFOS_NOT_EMPTY		BIT(1)
+#define CORE_BUSY			BIT(0)
+#define MANUAL_MODE_CFG			0x0024
+#define MANUAL_MODE_EN			BIT(0)
+#define DSI2_TIMEOUT_HSTX_CFG		0x0048
+#define TO_HSTX(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_HSTXRDY_CFG	0x004c
+#define TO_HSTXRDY(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_LPRX_CFG		0x0050
+#define TO_LPRXRDY(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_LPTXRDY_CFG	0x0054
+#define TO_LPTXRDY(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_LPTXTRIG_CFG	0x0058
+#define TO_LPTXTRIG(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_LPTXULPS_CFG	0x005c
+#define TO_LPTXULPS(x)			UPDATE(x, 15, 0)
+#define DSI2_TIMEOUT_BTA_CFG		0x60
+#define TO_BTA(x)			UPDATE(x, 15, 0)
+
+#define DSI2_PHY_MODE_CFG		0x0100
+#define PPI_WIDTH(x)			UPDATE(x, 9, 8)
+#define PHY_LANES(x)			UPDATE((x) - 1, 5, 4)
+#define PHY_TYPE(x)			UPDATE(x, 0, 0)
+#define DSI2_PHY_CLK_CFG		0X0104
+#define PHY_LPTX_CLK_DIV(x)		UPDATE(x, 12, 8)
+#define CLK_TYPE_MASK			BIT(0)
+#define NON_CONTINUOUS_CLK		BIT(0)
+#define CONTINUOUS_CLK			0
+#define DSI2_PHY_LP2HS_MAN_CFG		0x010c
+#define PHY_LP2HS_TIME(x)		UPDATE(x, 28, 0)
+#define DSI2_PHY_HS2LP_MAN_CFG		0x0114
+#define PHY_HS2LP_TIME(x)		UPDATE(x, 28, 0)
+#define DSI2_PHY_MAX_RD_T_MAN_CFG	0x011c
+#define PHY_MAX_RD_TIME(x)		UPDATE(x, 26, 0)
+#define DSI2_PHY_ESC_CMD_T_MAN_CFG	0x0124
+#define PHY_ESC_CMD_TIME(x)		UPDATE(x, 28, 0)
+#define DSI2_PHY_ESC_BYTE_T_MAN_CFG	0x012c
+#define PHY_ESC_BYTE_TIME(x)		UPDATE(x, 28, 0)
+
+#define DSI2_PHY_IPI_RATIO_MAN_CFG	0x0134
+#define PHY_IPI_RATIO(x)		UPDATE(x, 21, 0)
+#define DSI2_PHY_SYS_RATIO_MAN_CFG	0x013C
+#define PHY_SYS_RATIO(x)		UPDATE(x, 16, 0)
+
+#define DSI2_DSI_GENERAL_CFG		0x0200
+#define BTA_EN				BIT(1)
+#define EOTP_TX_EN			BIT(0)
+#define DSI2_DSI_VCID_CFG		0x0204
+#define TX_VCID(x)			UPDATE(x, 1, 0)
+#define DSI2_DSI_SCRAMBLING_CFG		0x0208
+#define SCRAMBLING_SEED(x)		UPDATE(x, 31, 16)
+#define SCRAMBLING_EN			BIT(0)
+#define DSI2_DSI_VID_TX_CFG		0x020c
+#define LPDT_DISPLAY_CMD_EN		BIT(20)
+#define BLK_VFP_HS_EN			BIT(14)
+#define BLK_VBP_HS_EN			BIT(13)
+#define BLK_VSA_HS_EN			BIT(12)
+#define BLK_HFP_HS_EN			BIT(6)
+#define BLK_HBP_HS_EN			BIT(5)
+#define BLK_HSA_HS_EN			BIT(4)
+#define VID_MODE_TYPE(x)		UPDATE(x, 1, 0)
+#define DSI2_CRI_TX_HDR			0x02c0
+#define CMD_TX_MODE(x)			UPDATE(x, 24, 24)
+#define DSI2_CRI_TX_PLD			0x02c4
+#define DSI2_CRI_RX_HDR			0x02c8
+#define DSI2_CRI_RX_PLD			0x02cc
+
+#define DSI2_IPI_COLOR_MAN_CFG		0x0300
+#define IPI_DEPTH(x)			UPDATE(x, 7, 4)
+#define IPI_DEPTH_5_6_5_BITS		0x02
+#define IPI_DEPTH_6_BITS		0x03
+#define IPI_DEPTH_8_BITS		0x05
+#define IPI_DEPTH_10_BITS		0x06
+#define IPI_FORMAT(x)			UPDATE(x, 3, 0)
+#define IPI_FORMAT_RGB			0x0
+#define IPI_FORMAT_DSC			0x0b
+#define DSI2_IPI_VID_HSA_MAN_CFG	0x0304
+#define VID_HSA_TIME(x)			UPDATE(x, 29, 0)
+#define DSI2_IPI_VID_HBP_MAN_CFG	0x030c
+#define VID_HBP_TIME(x)			UPDATE(x, 29, 0)
+#define DSI2_IPI_VID_HACT_MAN_CFG	0x0314
+#define VID_HACT_TIME(x)		UPDATE(x, 29, 0)
+#define DSI2_IPI_VID_HLINE_MAN_CFG	0x031c
+#define VID_HLINE_TIME(x)		UPDATE(x, 29, 0)
+#define DSI2_IPI_VID_VSA_MAN_CFG	0x0324
+#define VID_VSA_LINES(x)		UPDATE(x, 9, 0)
+#define DSI2_IPI_VID_VBP_MAN_CFG	0X032C
+#define VID_VBP_LINES(x)		UPDATE(x, 9, 0)
+#define DSI2_IPI_VID_VACT_MAN_CFG	0X0334
+#define VID_VACT_LINES(x)		UPDATE(x, 13, 0)
+#define DSI2_IPI_VID_VFP_MAN_CFG	0X033C
+#define VID_VFP_LINES(x)		UPDATE(x, 9, 0)
+#define DSI2_IPI_PIX_PKT_CFG		0x0344
+#define MAX_PIX_PKT(x)			UPDATE(x, 15, 0)
+
+#define DSI2_INT_ST_PHY			0x0400
+#define DSI2_INT_MASK_PHY		0x0404
+#define DSI2_INT_ST_TO			0x0410
+#define DSI2_INT_MASK_TO		0x0414
+#define DSI2_INT_ST_ACK			0x0420
+#define DSI2_INT_MASK_ACK		0x0424
+#define DSI2_INT_ST_IPI			0x0430
+#define DSI2_INT_MASK_IPI		0x0434
+#define DSI2_INT_ST_FIFO		0x0440
+#define DSI2_INT_MASK_FIFO		0x0444
+#define DSI2_INT_ST_PRI			0x0450
+#define DSI2_INT_MASK_PRI		0x0454
+#define DSI2_INT_ST_CRI			0x0460
+#define DSI2_INT_MASK_CRI		0x0464
+#define DSI2_INT_FORCE_CRI		0x0468
+#define DSI2_MAX_REGISGER		DSI2_INT_FORCE_CRI
+
+#define MODE_STATUS_TIMEOUT_US		10000
+#define CMD_PKT_STATUS_TIMEOUT_US	20000
+
+enum vid_mode_type {
+	VID_MODE_TYPE_NON_BURST_SYNC_PULSES,
+	VID_MODE_TYPE_NON_BURST_SYNC_EVENTS,
+	VID_MODE_TYPE_BURST,
+};
+
+enum mode_ctrl {
+	IDLE_MODE,
+	AUTOCALC_MODE,
+	COMMAND_MODE,
+	VIDEO_MODE,
+	DATA_STREAM_MODE,
+	VIDE_TEST_MODE,
+	DATA_STREAM_TEST_MODE,
+};
+
+enum ppi_width {
+	PPI_WIDTH_8_BITS,
+	PPI_WIDTH_16_BITS,
+	PPI_WIDTH_32_BITS,
+};
+
+struct cmd_header {
+	u8 cmd_type;
+	u8 delay;
+	u8 payload_length;
+};
+
+struct dw_mipi_dsi2 {
+	struct drm_bridge bridge;
+	struct mipi_dsi_host dsi_host;
+	struct drm_bridge *panel_bridge;
+	struct device *dev;
+	void __iomem *base;
+	struct clk *pclk;
+	struct clk *sys_clk;
+
+	unsigned int lane_mbps; /* per lane */
+	u32 channel;
+	u32 lanes;
+	u32 format;
+	unsigned long mode_flags;
+
+	struct drm_display_mode mode;
+	const struct dw_mipi_dsi2_plat_data *plat_data;
+};
+
+static inline struct dw_mipi_dsi2 *host_to_dsi2(struct mipi_dsi_host *host)
+{
+	return container_of(host, struct dw_mipi_dsi2, dsi_host);
+}
+
+static inline struct dw_mipi_dsi2 *bridge_to_dsi2(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct dw_mipi_dsi2, bridge);
+}
+
+static inline void dsi2_write(struct dw_mipi_dsi2 *dsi2, u32 reg, u32 val)
+{
+	writel(val, dsi2->base + reg);
+}
+
+static inline u32 dsi2_read(struct dw_mipi_dsi2 *dsi2, u32 reg)
+{
+	return readl(dsi2->base + reg);
+}
+
+static int cri_fifos_wait_avail(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 sts, mask;
+	int ret;
+
+	mask = CRI_BUSY | CRT_FIFOS_NOT_EMPTY;
+	ret = readl_poll_timeout(dsi2->base + DSI2_CORE_STATUS,
+				 sts, !(sts & mask), 0,
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret < 0) {
+		DRM_DEV_ERROR(dsi2->dev, "command interface is busy\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static void dw_mipi_dsi2_set_vid_mode(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 val = 0, mode;
+	int ret;
+
+	if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HFP)
+		val |= BLK_HFP_HS_EN;
+
+	if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HBP)
+		val |= BLK_HBP_HS_EN;
+
+	if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO_NO_HSA)
+		val |= BLK_HSA_HS_EN;
+
+	if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
+
+	dsi2_write(dsi2, DSI2_DSI_VID_TX_CFG, val);
+
+	dsi2_write(dsi2, DSI2_MODE_CTRL, VIDEO_MODE);
+	ret = readl_poll_timeout(dsi2->base + DSI2_MODE_STATUS,
+				 mode, mode & VIDEO_MODE, 1000,
+				 MODE_STATUS_TIMEOUT_US);
+	if (ret < 0)
+		dev_err(dsi2->dev, "failed to enter video mode\n");
+}
+
+static void dw_mipi_dsi2_set_data_stream_mode(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 mode;
+	int ret;
+
+	dsi2_write(dsi2, DSI2_MODE_CTRL, DATA_STREAM_MODE);
+	ret = readl_poll_timeout(dsi2->base + DSI2_MODE_STATUS,
+				 mode, mode & DATA_STREAM_MODE, 1000,
+				 MODE_STATUS_TIMEOUT_US);
+	if (ret < 0)
+		dev_err(dsi2->dev, "failed to enter data stream mode\n");
+}
+
+static void dw_mipi_dsi2_set_cmd_mode(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 mode;
+	int ret;
+
+	dsi2_write(dsi2, DSI2_MODE_CTRL, COMMAND_MODE);
+	ret = readl_poll_timeout(dsi2->base + DSI2_MODE_STATUS,
+				 mode, mode & COMMAND_MODE, 1000,
+				 MODE_STATUS_TIMEOUT_US);
+	if (ret < 0)
+		dev_err(dsi2->dev, "failed to enter data stream mode\n");
+}
+
+static void dw_mipi_dsi2_host_softrst(struct dw_mipi_dsi2 *dsi2)
+{
+	dsi2_write(dsi2, DSI2_SOFT_RESET, 0x0);
+	usleep_range(50, 100);
+	dsi2_write(dsi2, DSI2_SOFT_RESET,
+		   SYS_RSTN | PHY_RSTN | IPI_RSTN);
+}
+
+static void dw_mipi_dsi2_phy_clk_mode_cfg(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 sys_clk, esc_clk_div;
+	u32 val = 0;
+
+	/*
+	 * clk_type should be NON_CONTINUOUS_CLK before
+	 * initial deskew calibration be sent.
+	 */
+	val |= NON_CONTINUOUS_CLK;
+
+	/* The maximum value of the escape clock frequency is 20MHz */
+	sys_clk = clk_get_rate(dsi2->sys_clk) / USEC_PER_SEC;
+	esc_clk_div = DIV_ROUND_UP(sys_clk, 20 * 2);
+	val |= PHY_LPTX_CLK_DIV(esc_clk_div);
+
+	dsi2_write(dsi2, DSI2_PHY_CLK_CFG, val);
+}
+
+static void dw_mipi_dsi2_phy_ratio_cfg(struct dw_mipi_dsi2 *dsi2)
+{
+	struct drm_display_mode *mode = &dsi2->mode;
+	u64 sys_clk = clk_get_rate(dsi2->sys_clk);
+	u64 pixel_clk, ipi_clk, phy_hsclk;
+	u64 tmp;
+
+	/*
+	 * in DPHY mode, the phy_hstx_clk is exactly 1/16 the Lane high-speed
+	 * data rate; In CPHY mode, the phy_hstx_clk is exactly 1/7 the trio
+	 * high speed symbol rate.
+	 */
+	phy_hsclk = DIV_ROUND_CLOSEST_ULL(dsi2->lane_mbps * USEC_PER_SEC, 16);
+
+	/* IPI_RATIO_MAN_CFG = PHY_HSTX_CLK / IPI_CLK */
+	pixel_clk = mode->crtc_clock * MSEC_PER_SEC;
+	ipi_clk = pixel_clk / 4;
+
+	tmp = DIV_ROUND_CLOSEST_ULL(phy_hsclk << 16, ipi_clk);
+	dsi2_write(dsi2, DSI2_PHY_IPI_RATIO_MAN_CFG,
+		   PHY_IPI_RATIO(tmp));
+
+	/*
+	 * SYS_RATIO_MAN_CFG = MIPI_DCPHY_HSCLK_Freq / MIPI_DCPHY_HSCLK_Freq
+	 */
+	tmp = DIV_ROUND_CLOSEST_ULL(phy_hsclk << 16, sys_clk);
+	dsi2_write(dsi2, DSI2_PHY_SYS_RATIO_MAN_CFG,
+		   PHY_SYS_RATIO(tmp));
+}
+
+static void dw_mipi_dsi2_lp2hs_or_hs2lp_cfg(struct dw_mipi_dsi2 *dsi2)
+{
+	const struct dw_mipi_dsi2_phy_ops *phy_ops = dsi2->plat_data->phy_ops;
+	struct dw_mipi_dsi2_phy_timing timing;
+	int ret;
+
+	ret = phy_ops->get_timing(dsi2->plat_data->priv_data,
+				  dsi2->lane_mbps, &timing);
+	if (ret)
+		DRM_DEV_ERROR(dsi2->dev, "Retrieving phy timings failed\n");
+
+	dsi2_write(dsi2, DSI2_PHY_LP2HS_MAN_CFG, PHY_LP2HS_TIME(timing.data_lp2hs));
+	dsi2_write(dsi2, DSI2_PHY_HS2LP_MAN_CFG, PHY_HS2LP_TIME(timing.data_hs2lp));
+}
+
+static void dw_mipi_dsi2_phy_init(struct dw_mipi_dsi2 *dsi2)
+{
+	const struct dw_mipi_dsi2_phy_ops *phy_ops = dsi2->plat_data->phy_ops;
+	struct dw_mipi_dsi2_phy_iface iface;
+	u32 val = 0;
+
+	phy_ops->get_interface(dsi2->plat_data->priv_data, &iface);
+
+	switch (iface.ppi_width) {
+	case 8:
+		val |= PPI_WIDTH(PPI_WIDTH_8_BITS);
+		break;
+	case 16:
+		val |= PPI_WIDTH(PPI_WIDTH_16_BITS);
+		break;
+	case 32:
+		val |= PPI_WIDTH(PPI_WIDTH_32_BITS);
+		break;
+	default:
+		/* Caught in probe */
+		break;
+	}
+
+	val |= PHY_LANES(dsi2->lanes);
+	val |= PHY_TYPE(DW_MIPI_DSI2_DPHY);
+	dsi2_write(dsi2, DSI2_PHY_MODE_CFG, val);
+
+	dw_mipi_dsi2_phy_clk_mode_cfg(dsi2);
+	dw_mipi_dsi2_phy_ratio_cfg(dsi2);
+	dw_mipi_dsi2_lp2hs_or_hs2lp_cfg(dsi2);
+
+	/* phy configuration 8 - 10 */
+}
+
+static void dw_mipi_dsi2_tx_option_set(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 val;
+
+	val = BTA_EN | EOTP_TX_EN;
+
+	if (dsi2->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET)
+		val &= ~EOTP_TX_EN;
+
+	dsi2_write(dsi2, DSI2_DSI_GENERAL_CFG, val);
+	dsi2_write(dsi2, DSI2_DSI_VCID_CFG, TX_VCID(dsi2->channel));
+}
+
+static void dw_mipi_dsi2_ipi_color_coding_cfg(struct dw_mipi_dsi2 *dsi2)
+{
+	u32 val, color_depth;
+
+	switch (dsi2->format) {
+	case MIPI_DSI_FMT_RGB666:
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		color_depth = IPI_DEPTH_6_BITS;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		color_depth = IPI_DEPTH_5_6_5_BITS;
+		break;
+	case MIPI_DSI_FMT_RGB888:
+	default:
+		color_depth = IPI_DEPTH_8_BITS;
+		break;
+	}
+
+	val = IPI_DEPTH(color_depth) |
+	      IPI_FORMAT(IPI_FORMAT_RGB);
+	dsi2_write(dsi2, DSI2_IPI_COLOR_MAN_CFG, val);
+}
+
+static void dw_mipi_dsi2_vertical_timing_config(struct dw_mipi_dsi2 *dsi2,
+						const struct drm_display_mode *mode)
+{
+	u32 vactive, vsa, vfp, vbp;
+
+	vactive = mode->vdisplay;
+	vsa = mode->vsync_end - mode->vsync_start;
+	vfp = mode->vsync_start - mode->vdisplay;
+	vbp = mode->vtotal - mode->vsync_end;
+
+	dsi2_write(dsi2, DSI2_IPI_VID_VSA_MAN_CFG, VID_VSA_LINES(vsa));
+	dsi2_write(dsi2, DSI2_IPI_VID_VBP_MAN_CFG, VID_VBP_LINES(vbp));
+	dsi2_write(dsi2, DSI2_IPI_VID_VACT_MAN_CFG, VID_VACT_LINES(vactive));
+	dsi2_write(dsi2, DSI2_IPI_VID_VFP_MAN_CFG, VID_VFP_LINES(vfp));
+}
+
+static void dw_mipi_dsi2_ipi_set(struct dw_mipi_dsi2 *dsi2)
+{
+	struct drm_display_mode *mode = &dsi2->mode;
+	u32 hline, hsa, hbp, hact;
+	u64 hline_time, hsa_time, hbp_time, hact_time, tmp;
+	u64 pixel_clk, phy_hs_clk;
+	u16 val;
+
+	val = mode->hdisplay;
+
+	dsi2_write(dsi2, DSI2_IPI_PIX_PKT_CFG, MAX_PIX_PKT(val));
+
+	dw_mipi_dsi2_ipi_color_coding_cfg(dsi2);
+
+	/*
+	 * if the controller is intended to operate in data stream mode,
+	 * no more steps are required.
+	 */
+	if (!(dsi2->mode_flags & MIPI_DSI_MODE_VIDEO))
+		return;
+
+	hact = mode->hdisplay;
+	hsa = mode->hsync_end - mode->hsync_start;
+	hbp = mode->htotal - mode->hsync_end;
+	hline = mode->htotal;
+
+	pixel_clk = mode->crtc_clock * MSEC_PER_SEC;
+
+	phy_hs_clk = DIV_ROUND_CLOSEST_ULL(dsi2->lane_mbps * USEC_PER_SEC, 16);
+
+	tmp = hsa * phy_hs_clk;
+	hsa_time = DIV_ROUND_CLOSEST_ULL(tmp << 16, pixel_clk);
+	dsi2_write(dsi2, DSI2_IPI_VID_HSA_MAN_CFG, VID_HSA_TIME(hsa_time));
+
+	tmp = hbp * phy_hs_clk;
+	hbp_time = DIV_ROUND_CLOSEST_ULL(tmp << 16, pixel_clk);
+	dsi2_write(dsi2, DSI2_IPI_VID_HBP_MAN_CFG, VID_HBP_TIME(hbp_time));
+
+	tmp = hact * phy_hs_clk;
+	hact_time = DIV_ROUND_CLOSEST_ULL(tmp << 16, pixel_clk);
+	dsi2_write(dsi2, DSI2_IPI_VID_HACT_MAN_CFG, VID_HACT_TIME(hact_time));
+
+	tmp = hline * phy_hs_clk;
+	hline_time = DIV_ROUND_CLOSEST_ULL(tmp << 16, pixel_clk);
+	dsi2_write(dsi2, DSI2_IPI_VID_HLINE_MAN_CFG, VID_HLINE_TIME(hline_time));
+
+	dw_mipi_dsi2_vertical_timing_config(dsi2, mode);
+}
+
+static void
+dw_mipi_dsi2_work_mode(struct dw_mipi_dsi2 *dsi2, u32 mode)
+{
+	/*
+	 * select controller work in Manual mode
+	 * Manual: MANUAL_MODE_EN
+	 * Automatic: 0
+	 */
+	dsi2_write(dsi2, MANUAL_MODE_CFG, mode);
+}
+
+static int dw_mipi_dsi2_host_attach(struct mipi_dsi_host *host,
+				    struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi2 *dsi2 = host_to_dsi2(host);
+	const struct dw_mipi_dsi2_plat_data *pdata = dsi2->plat_data;
+	struct drm_bridge *bridge;
+	int ret;
+
+	if (device->lanes > dsi2->plat_data->max_data_lanes) {
+		dev_err(dsi2->dev, "the number of data lanes(%u) is too many\n",
+			device->lanes);
+		return -EINVAL;
+	}
+
+	dsi2->lanes = device->lanes;
+	dsi2->channel = device->channel;
+	dsi2->format = device->format;
+	dsi2->mode_flags = device->mode_flags;
+
+	bridge = devm_drm_of_get_bridge(dsi2->dev, dsi2->dev->of_node, 1, 0);
+	if (IS_ERR(bridge))
+		return PTR_ERR(bridge);
+
+	bridge->pre_enable_prev_first = true;
+	dsi2->panel_bridge = bridge;
+
+	drm_bridge_add(&dsi2->bridge);
+
+	if (pdata->host_ops && pdata->host_ops->attach) {
+		ret = pdata->host_ops->attach(pdata->priv_data, device);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int dw_mipi_dsi2_host_detach(struct mipi_dsi_host *host,
+				    struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi2 *dsi2 = host_to_dsi2(host);
+	const struct dw_mipi_dsi2_plat_data *pdata = dsi2->plat_data;
+	int ret;
+
+	if (pdata->host_ops && pdata->host_ops->detach) {
+		ret = pdata->host_ops->detach(pdata->priv_data, device);
+		if (ret < 0)
+			return ret;
+	}
+
+	drm_bridge_remove(&dsi2->bridge);
+
+	drm_of_panel_bridge_remove(host->dev->of_node, 1, 0);
+
+	return 0;
+}
+
+static int dw_mipi_dsi2_gen_pkt_hdr_write(struct dw_mipi_dsi2 *dsi2,
+					  u32 hdr_val, bool lpm)
+{
+	int ret;
+
+	dsi2_write(dsi2, DSI2_CRI_TX_HDR, hdr_val | CMD_TX_MODE(lpm));
+
+	ret = cri_fifos_wait_avail(dsi2);
+	if (ret) {
+		dev_err(dsi2->dev, "failed to write command header\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dw_mipi_dsi2_write(struct dw_mipi_dsi2 *dsi2,
+			      const struct mipi_dsi_packet *packet, bool lpm)
+{
+	const u8 *tx_buf = packet->payload;
+	int len = packet->payload_length, pld_data_bytes = sizeof(u32);
+	__le32 word;
+
+	/* Send payload */
+	while (len) {
+		if (len < pld_data_bytes) {
+			word = 0;
+			memcpy(&word, tx_buf, len);
+			dsi2_write(dsi2, DSI2_CRI_TX_PLD, le32_to_cpu(word));
+			len = 0;
+		} else {
+			memcpy(&word, tx_buf, pld_data_bytes);
+			dsi2_write(dsi2, DSI2_CRI_TX_PLD, le32_to_cpu(word));
+			tx_buf += pld_data_bytes;
+			len -= pld_data_bytes;
+		}
+	}
+
+	word = 0;
+	memcpy(&word, packet->header, sizeof(packet->header));
+	return dw_mipi_dsi2_gen_pkt_hdr_write(dsi2, le32_to_cpu(word), lpm);
+}
+
+static int dw_mipi_dsi2_read(struct dw_mipi_dsi2 *dsi2,
+			     const struct mipi_dsi_msg *msg)
+{
+	u8 *payload = msg->rx_buf;
+	int i, j, ret, len = msg->rx_len;
+	u8 data_type;
+	u16 wc;
+	u32 val;
+
+	ret = readl_poll_timeout(dsi2->base + DSI2_CORE_STATUS,
+				 val, val & CRI_RD_DATA_AVAIL, 1000,
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret) {
+		dev_err(dsi2->dev, "CRI has no available read data\n");
+		return ret;
+	}
+
+	val = dsi2_read(dsi2, DSI2_CRI_RX_HDR);
+	data_type = val & 0x3f;
+
+	if (mipi_dsi_packet_format_is_short(data_type)) {
+		for (i = 0; i < len && i < 2; i++)
+			payload[i] = (val >> (8 * (i + 1))) & 0xff;
+
+		return 0;
+	}
+
+	wc = (val >> 8) & 0xffff;
+	/* Receive payload */
+	for (i = 0; i < len && i < wc; i += 4) {
+		val = dsi2_read(dsi2, DSI2_CRI_RX_PLD);
+		for (j = 0; j < 4 && j + i < len && j + i < wc; j++)
+			payload[i + j] = val >> (8 * j);
+	}
+
+	return 0;
+}
+
+static ssize_t dw_mipi_dsi2_host_transfer(struct mipi_dsi_host *host,
+					  const struct mipi_dsi_msg *msg)
+{
+	struct dw_mipi_dsi2 *dsi2 = host_to_dsi2(host);
+	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
+	struct mipi_dsi_packet packet;
+	int ret, nb_bytes;
+	u32 val;
+
+	val = dsi2_read(dsi2, DSI2_DSI_VID_TX_CFG);
+	if (lpm)
+		val |= LPDT_DISPLAY_CMD_EN;
+	else
+		val &= ~LPDT_DISPLAY_CMD_EN;
+	dsi2_write(dsi2, DSI2_DSI_VID_TX_CFG, val);
+
+	/* create a packet to the DSI protocol */
+	ret = mipi_dsi_create_packet(&packet, msg);
+	if (ret) {
+		DRM_DEV_ERROR(dsi2->dev, "failed to create packet: %d\n", ret);
+		return ret;
+	}
+
+	ret = cri_fifos_wait_avail(dsi2);
+	if (ret)
+		return ret;
+
+	ret = dw_mipi_dsi2_write(dsi2, &packet, lpm);
+	if (ret)
+		return ret;
+
+	if (msg->rx_buf && msg->rx_len) {
+		ret = dw_mipi_dsi2_read(dsi2, msg);
+		if (ret < 0)
+			return ret;
+		nb_bytes = msg->rx_len;
+	} else {
+		nb_bytes = packet.size;
+	}
+
+	return nb_bytes;
+}
+
+static const struct mipi_dsi_host_ops dw_mipi_dsi2_host_ops = {
+	.attach = dw_mipi_dsi2_host_attach,
+	.detach = dw_mipi_dsi2_host_detach,
+	.transfer = dw_mipi_dsi2_host_transfer,
+};
+
+static u32 *
+dw_mipi_dsi2_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+					      struct drm_bridge_state *bridge_state,
+					      struct drm_crtc_state *crtc_state,
+					      struct drm_connector_state *conn_state,
+					      u32 output_fmt,
+					      unsigned int *num_input_fmts)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+	const struct dw_mipi_dsi2_plat_data *pdata = dsi2->plat_data;
+	u32 *input_fmts;
+
+	if (pdata->get_input_bus_fmts)
+		return pdata->get_input_bus_fmts(pdata->priv_data,
+						 bridge, bridge_state,
+						 crtc_state, conn_state,
+						 output_fmt, num_input_fmts);
+
+	/* Fall back to MEDIA_BUS_FMT_FIXED as the only input format. */
+	input_fmts = kmalloc(sizeof(*input_fmts), GFP_KERNEL);
+	if (!input_fmts)
+		return NULL;
+	input_fmts[0] = MEDIA_BUS_FMT_FIXED;
+	*num_input_fmts = 1;
+
+	return input_fmts;
+}
+
+static int dw_mipi_dsi2_bridge_atomic_check(struct drm_bridge *bridge,
+					    struct drm_bridge_state *bridge_state,
+					    struct drm_crtc_state *crtc_state,
+					    struct drm_connector_state *conn_state)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+	const struct dw_mipi_dsi2_plat_data *pdata = dsi2->plat_data;
+	bool ret;
+
+	bridge_state->input_bus_cfg.flags =
+		DRM_BUS_FLAG_DE_HIGH | DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE;
+
+	if (pdata->mode_fixup) {
+		ret = pdata->mode_fixup(pdata->priv_data, &crtc_state->mode,
+					&crtc_state->adjusted_mode);
+		if (!ret) {
+			DRM_DEBUG_DRIVER("failed to fixup mode " DRM_MODE_FMT "\n",
+					 DRM_MODE_ARG(&crtc_state->mode));
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static void dw_mipi_dsi2_bridge_post_atomic_disable(struct drm_bridge *bridge,
+						    struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+	const struct dw_mipi_dsi2_phy_ops *phy_ops = dsi2->plat_data->phy_ops;
+
+	dsi2_write(dsi2, DSI2_IPI_PIX_PKT_CFG, 0);
+
+	/*
+	 * Switch to command mode before panel-bridge post_disable &
+	 * panel unprepare.
+	 * Note: panel-bridge disable & panel disable has been called
+	 * before by the drm framework.
+	 */
+	dw_mipi_dsi2_set_cmd_mode(dsi2);
+
+	dsi2_write(dsi2, DSI2_PWR_UP, RESET);
+
+	if (phy_ops->power_off)
+		phy_ops->power_off(dsi2->plat_data->priv_data);
+
+	clk_disable_unprepare(dsi2->pclk);
+	pm_runtime_put(dsi2->dev);
+}
+
+static unsigned int dw_mipi_dsi2_get_lanes(struct dw_mipi_dsi2 *dsi2)
+{
+	/* single-dsi, so no other instance to consider */
+	return dsi2->lanes;
+}
+
+static void dw_mipi_dsi2_mode_set(struct dw_mipi_dsi2 *dsi2,
+				  const struct drm_display_mode *adjusted_mode)
+{
+	const struct dw_mipi_dsi2_phy_ops *phy_ops = dsi2->plat_data->phy_ops;
+	void *priv_data = dsi2->plat_data->priv_data;
+	u32 lanes = dw_mipi_dsi2_get_lanes(dsi2);
+	int ret;
+	u32 val;
+
+	clk_prepare_enable(dsi2->pclk);
+
+	ret = phy_ops->get_lane_mbps(priv_data, adjusted_mode, dsi2->mode_flags,
+				     lanes, dsi2->format, &dsi2->lane_mbps);
+	if (ret)
+		DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
+
+	pm_runtime_get_sync(dsi2->dev);
+
+	dw_mipi_dsi2_host_softrst(dsi2);
+	dsi2_write(dsi2, DSI2_PWR_UP, RESET);
+
+	dw_mipi_dsi2_work_mode(dsi2, MANUAL_MODE_EN);
+	dw_mipi_dsi2_phy_init(dsi2);
+
+	if (phy_ops->power_on)
+		phy_ops->power_on(dsi2->plat_data->priv_data);
+
+	dw_mipi_dsi2_tx_option_set(dsi2);
+
+	/*
+	 * initial deskew calibration is send after phy_power_on,
+	 * then we can configure clk_type.
+	 */
+
+	val = dsi2_read(dsi2, DSI2_PHY_CLK_CFG);
+	val &= ~CLK_TYPE_MASK;
+	val |= (dsi2->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ?
+					NON_CONTINUOUS_CLK : CONTINUOUS_CLK;
+	dsi2_write(dsi2, DSI2_PHY_CLK_CFG, val);
+
+	dsi2_write(dsi2, DSI2_PWR_UP, POWER_UP);
+	dw_mipi_dsi2_set_cmd_mode(dsi2);
+
+	dw_mipi_dsi2_ipi_set(dsi2);
+}
+
+static void dw_mipi_dsi2_bridge_atomic_pre_enable(struct drm_bridge *bridge,
+						  struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+
+	/* Power up the dsi ctl into a command mode */
+	dw_mipi_dsi2_mode_set(dsi2, &dsi2->mode);
+}
+
+static void dw_mipi_dsi2_bridge_mode_set(struct drm_bridge *bridge,
+					 const struct drm_display_mode *mode,
+					 const struct drm_display_mode *adjusted_mode)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+
+	/* Store the display mode for later use in pre_enable callback */
+	drm_mode_copy(&dsi2->mode, adjusted_mode);
+}
+
+static void dw_mipi_dsi2_bridge_atomic_enable(struct drm_bridge *bridge,
+					      struct drm_bridge_state *old_bridge_state)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+
+	/* Switch to video mode for panel-bridge enable & panel enable */
+	if (dsi2->mode_flags & MIPI_DSI_MODE_VIDEO)
+		dw_mipi_dsi2_set_vid_mode(dsi2);
+	else
+		dw_mipi_dsi2_set_data_stream_mode(dsi2);
+}
+
+static enum drm_mode_status
+dw_mipi_dsi2_bridge_mode_valid(struct drm_bridge *bridge,
+			       const struct drm_display_info *info,
+			       const struct drm_display_mode *mode)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+	const struct dw_mipi_dsi2_plat_data *pdata = dsi2->plat_data;
+	enum drm_mode_status mode_status = MODE_OK;
+
+	if (pdata->mode_valid)
+		mode_status = pdata->mode_valid(pdata->priv_data, mode,
+						dsi2->mode_flags,
+						dw_mipi_dsi2_get_lanes(dsi2),
+						dsi2->format);
+
+	return mode_status;
+}
+
+static int dw_mipi_dsi2_bridge_attach(struct drm_bridge *bridge,
+				      enum drm_bridge_attach_flags flags)
+{
+	struct dw_mipi_dsi2 *dsi2 = bridge_to_dsi2(bridge);
+
+	/* Set the encoder type as caller does not know it */
+	bridge->encoder->encoder_type = DRM_MODE_ENCODER_DSI;
+
+	/* Attach the panel-bridge to the dsi bridge */
+	return drm_bridge_attach(bridge->encoder, dsi2->panel_bridge, bridge,
+				 flags);
+}
+
+static const struct drm_bridge_funcs dw_mipi_dsi2_bridge_funcs = {
+	.atomic_duplicate_state	= drm_atomic_helper_bridge_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_bridge_destroy_state,
+	.atomic_get_input_bus_fmts = dw_mipi_dsi2_bridge_atomic_get_input_bus_fmts,
+	.atomic_check		= dw_mipi_dsi2_bridge_atomic_check,
+	.atomic_reset		= drm_atomic_helper_bridge_reset,
+	.atomic_pre_enable	= dw_mipi_dsi2_bridge_atomic_pre_enable,
+	.atomic_enable		= dw_mipi_dsi2_bridge_atomic_enable,
+	.atomic_post_disable	= dw_mipi_dsi2_bridge_post_atomic_disable,
+	.mode_set		= dw_mipi_dsi2_bridge_mode_set,
+	.mode_valid		= dw_mipi_dsi2_bridge_mode_valid,
+	.attach			= dw_mipi_dsi2_bridge_attach,
+};
+
+static struct dw_mipi_dsi2 *
+__dw_mipi_dsi2_probe(struct platform_device *pdev,
+		     const struct dw_mipi_dsi2_plat_data *plat_data)
+{
+	struct device *dev = &pdev->dev;
+	struct reset_control *apb_rst;
+	struct dw_mipi_dsi2 *dsi2;
+	int ret;
+
+	dsi2 = devm_kzalloc(dev, sizeof(*dsi2), GFP_KERNEL);
+	if (!dsi2)
+		return ERR_PTR(-ENOMEM);
+
+	dsi2->dev = dev;
+	dsi2->plat_data = plat_data;
+
+	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps ||
+	    !plat_data->phy_ops->get_timing)
+		return dev_err_ptr_probe(dev, -ENODEV, "Phy not properly configured\n");
+
+	if (!plat_data->base) {
+		dsi2->base = devm_platform_ioremap_resource(pdev, 0);
+		if (IS_ERR(dsi2->base))
+			return ERR_PTR(-ENODEV);
+	} else {
+		dsi2->base = plat_data->base;
+	}
+
+	dsi2->pclk = devm_clk_get(dev, "pclk");
+	if (IS_ERR(dsi2->pclk))
+		return dev_err_cast_probe(dev, dsi2->pclk, "Unable to get pclk\n");
+
+	dsi2->sys_clk = devm_clk_get(dev, "sys");
+	if (IS_ERR(dsi2->sys_clk))
+		return dev_err_cast_probe(dev, dsi2->sys_clk, "Unable to get sys_clk\n");
+
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = devm_reset_control_get_optional_exclusive(dev, "apb");
+	if (IS_ERR(apb_rst))
+		return dev_err_cast_probe(dev, apb_rst, "Unable to get reset control\n");
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi2->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ERR_PTR(ret);
+		}
+
+		reset_control_assert(apb_rst);
+		usleep_range(10, 20);
+		reset_control_deassert(apb_rst);
+
+		clk_disable_unprepare(dsi2->pclk);
+	}
+
+	pm_runtime_enable(dev);
+
+	dsi2->dsi_host.ops = &dw_mipi_dsi2_host_ops;
+	dsi2->dsi_host.dev = dev;
+	ret = mipi_dsi_host_register(&dsi2->dsi_host);
+	if (ret) {
+		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
+		pm_runtime_disable(dev);
+		return ERR_PTR(ret);
+	}
+
+	dsi2->bridge.driver_private = dsi2;
+	dsi2->bridge.funcs = &dw_mipi_dsi2_bridge_funcs;
+	dsi2->bridge.of_node = pdev->dev.of_node;
+
+	return dsi2;
+}
+
+static void __dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
+{
+	mipi_dsi_host_unregister(&dsi2->dsi_host);
+
+	pm_runtime_disable(dsi2->dev);
+}
+
+/*
+ * Probe/remove API, used from platforms based on the DRM bridge API.
+ */
+struct dw_mipi_dsi2 *
+dw_mipi_dsi2_probe(struct platform_device *pdev,
+		   const struct dw_mipi_dsi2_plat_data *plat_data)
+{
+	return __dw_mipi_dsi2_probe(pdev, plat_data);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi2_probe);
+
+void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
+{
+	__dw_mipi_dsi2_remove(dsi2);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi2_remove);
+
+/*
+ * Bind/unbind API, used from platforms based on the component framework.
+ */
+int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder)
+{
+	return drm_bridge_attach(encoder, &dsi2->bridge, NULL, 0);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi2_bind);
+
+void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2)
+{
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi2_unbind);
+
+MODULE_AUTHOR("Guochun Huang <hero.huang@rock-chips.com>");
+MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@cherry.de>");
+MODULE_DESCRIPTION("DW MIPI DSI2 host controller driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:dw-mipi-dsi2");
diff --git a/include/drm/bridge/dw_mipi_dsi2.h b/include/drm/bridge/dw_mipi_dsi2.h
new file mode 100644
index 000000000000..ef5479b35028
--- /dev/null
+++ b/include/drm/bridge/dw_mipi_dsi2.h
@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2024, Fuzhou Rockchip Electronics Co., Ltd
+ *
+ * Authors: Guochun Huang <hero.huang@rock-chips.com>
+ *          Heiko Stuebner <heiko.stuebner@cherry.de>
+ */
+
+#ifndef __DW_MIPI_DSI2__
+#define __DW_MIPI_DSI2__
+
+#include <linux/types.h>
+
+#include <drm/drm_atomic.h>
+#include <drm/drm_bridge.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_modes.h>
+
+struct drm_display_mode;
+struct drm_encoder;
+struct dw_mipi_dsi2;
+struct mipi_dsi_device;
+struct platform_device;
+
+enum dw_mipi_dsi2_phy_type {
+	DW_MIPI_DSI2_DPHY,
+	DW_MIPI_DSI2_CPHY,
+};
+
+struct dw_mipi_dsi2_phy_iface {
+	int ppi_width;
+	enum dw_mipi_dsi2_phy_type phy_type;
+};
+
+struct dw_mipi_dsi2_phy_timing {
+	u32 data_hs2lp;
+	u32 data_lp2hs;
+};
+
+struct dw_mipi_dsi2_phy_ops {
+	int (*init)(void *priv_data);
+	void (*power_on)(void *priv_data);
+	void (*power_off)(void *priv_data);
+	void (*get_interface)(void *priv_data, struct dw_mipi_dsi2_phy_iface *iface);
+	int (*get_lane_mbps)(void *priv_data,
+			     const struct drm_display_mode *mode,
+			     unsigned long mode_flags, u32 lanes, u32 format,
+			     unsigned int *lane_mbps);
+	int (*get_timing)(void *priv_data, unsigned int lane_mbps,
+			  struct dw_mipi_dsi2_phy_timing *timing);
+	int (*get_esc_clk_rate)(void *priv_data, unsigned int *esc_clk_rate);
+};
+
+struct dw_mipi_dsi2_host_ops {
+	int (*attach)(void *priv_data,
+		      struct mipi_dsi_device *dsi);
+	int (*detach)(void *priv_data,
+		      struct mipi_dsi_device *dsi);
+};
+
+struct dw_mipi_dsi2_plat_data {
+	void __iomem *base;
+	unsigned int max_data_lanes;
+
+	enum drm_mode_status (*mode_valid)(void *priv_data,
+					   const struct drm_display_mode *mode,
+					   unsigned long mode_flags,
+					   u32 lanes, u32 format);
+
+	bool (*mode_fixup)(void *priv_data, const struct drm_display_mode *mode,
+			   struct drm_display_mode *adjusted_mode);
+
+	u32 *(*get_input_bus_fmts)(void *priv_data,
+				   struct drm_bridge *bridge,
+				   struct drm_bridge_state *bridge_state,
+				   struct drm_crtc_state *crtc_state,
+				   struct drm_connector_state *conn_state,
+				   u32 output_fmt,
+				   unsigned int *num_input_fmts);
+
+	const struct dw_mipi_dsi2_phy_ops *phy_ops;
+	const struct dw_mipi_dsi2_host_ops *host_ops;
+
+	void *priv_data;
+};
+
+struct dw_mipi_dsi2 *dw_mipi_dsi2_probe(struct platform_device *pdev,
+					const struct dw_mipi_dsi2_plat_data *plat_data);
+void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2);
+int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder);
+void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2);
+
+#endif /* __DW_MIPI_DSI2__ */
-- 
2.45.2

[PATCH 2/3] dt-bindings: display: rockchip: Add schema for RK3588 DW DSI2 controller

[Heiko Stuebner]

From: Heiko Stuebner <heiko.stuebner@cherry.de>

The Display Serial Interface 2 (DSI-2) is part of a group of communication
protocols defined by the MIPI Alliance. The RK3588 implements this
specification in its two MIPI DSI-2 Host Controllers that are based on a
new Synopsis IP.

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 .../rockchip/rockchip,rk3588-mipi-dsi2.yaml   | 119 ++++++++++++++++++
 1 file changed, 119 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml

diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
new file mode 100644
index 000000000000..8fc6b4a63f06
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/rockchip/rockchip,dw-mipi-dsi2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip specific extensions to the Synopsys Designware MIPI DSI2
+
+maintainers:
+  - Heiko Stuebner <heiko@sntech.de>
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk3588-mipi-dsi2
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: pclk
+      - const: sys
+
+  rockchip,grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      This SoC uses GRF regs to switch between vopl/vopb.
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dcphy
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input node to receive pixel data.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: DSI output node to panel.
+
+    required:
+      - port@0
+      - port@1
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: apb
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - rockchip,grf
+  - phys
+  - phy-names
+  - ports
+  - reg
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rockchip,rk3588-cru.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/rk3588-power.h>
+    #include <dt-bindings/reset/rockchip,rk3588-cru.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      dsi0: dsi@fde20000 {
+        compatible = "rockchip,rk3588-mipi-dsi2";
+        reg = <0x0 0xfde20000 0x0 0x10000>;
+        interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH 0>;
+        clocks = <&cru PCLK_DSIHOST0>, <&cru CLK_DSIHOST0>;
+        clock-names = "pclk", "sys";
+        resets = <&cru SRST_P_DSIHOST0>;
+        reset-names = "apb";
+        power-domains = <&power RK3588_PD_VOP>;
+        phys = <&mipidcphy0>;
+        phy-names = "dcphy";
+        rockchip,grf = <&vop_grf>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+          dsi0_in: port@0 {
+            reg = <0>;
+          };
+
+          dsi0_out: port@1 {
+            reg = <1>;
+          };
+        };
+      };
+    };
-- 
2.45.2

[PATCH 3/3] drm/rockchip: Add MIPI DSI2 glue driver for RK3588

[Heiko Stuebner]

From: Heiko Stuebner <heiko.stuebner@cherry.de>

This adds the glue code for the MIPI DSI2 bridge on Rockchip SoCs and
enables its use on the RK3588.

Right now the DSI2 controller is always paired with a DC-phy based on a
Samsung IP, so the interface values are set statically for now.
This stays true for the upcoming RK3576 as well.

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 drivers/gpu/drm/rockchip/Kconfig              |  10 +
 drivers/gpu/drm/rockchip/Makefile             |   1 +
 .../gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c  | 524 ++++++++++++++++++
 drivers/gpu/drm/rockchip/rockchip_drm_drv.c   |   2 +
 drivers/gpu/drm/rockchip/rockchip_drm_drv.h   |   1 +
 5 files changed, 538 insertions(+)
 create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c

diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig
index 448fadd4ba15..99d4b260de85 100644
--- a/drivers/gpu/drm/rockchip/Kconfig
+++ b/drivers/gpu/drm/rockchip/Kconfig
@@ -10,6 +10,7 @@ config DRM_ROCKCHIP
 	select DRM_DW_HDMI if ROCKCHIP_DW_HDMI
 	select DRM_DW_HDMI_QP if ROCKCHIP_DW_HDMI_QP
 	select DRM_DW_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI
+	select DRM_DW_MIPI_DSI2 if ROCKCHIP_DW_MIPI_DSI2
 	select GENERIC_PHY if ROCKCHIP_DW_MIPI_DSI
 	select GENERIC_PHY_MIPI_DPHY if ROCKCHIP_DW_MIPI_DSI
 	select SND_SOC_HDMI_CODEC if ROCKCHIP_CDN_DP && SND_SOC
@@ -81,6 +82,15 @@ config ROCKCHIP_DW_MIPI_DSI
 	  enable MIPI DSI on RK3288 or RK3399 based SoC, you should
 	  select this option.
 
+config ROCKCHIP_DW_MIPI_DSI2
+	bool "Rockchip specific extensions for Synopsys DW MIPI DSI"
+	select GENERIC_PHY_MIPI_DPHY
+	help
+	  This selects support for Rockchip SoC specific extensions
+	  for the Synopsys DesignWare dsi driver. If you want to
+	  enable MIPI DSI on RK3288 or RK3399 based SoC, you should
+	  select this option.
+
 config ROCKCHIP_INNO_HDMI
 	bool "Rockchip specific extensions for Innosilicon HDMI"
 	select DRM_DISPLAY_HDMI_HELPER
diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
index 3eab662a5a1d..2b867cebbc12 100644
--- a/drivers/gpu/drm/rockchip/Makefile
+++ b/drivers/gpu/drm/rockchip/Makefile
@@ -13,6 +13,7 @@ rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o
 rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
 rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI_QP) += dw_hdmi_qp-rockchip.o
 rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi-rockchip.o
+rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI2) += dw-mipi-dsi2-rockchip.o
 rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o
 rockchipdrm-$(CONFIG_ROCKCHIP_LVDS) += rockchip_lvds.o
 rockchipdrm-$(CONFIG_ROCKCHIP_RGB) += rockchip_rgb.o
diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
new file mode 100644
index 000000000000..42a7a80e2138
--- /dev/null
+++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
@@ -0,0 +1,524 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Rockchip Electronics Co.Ltd
+ * Author:
+ *      Guochun Huang <hero.huang@rock-chips.com>
+ *      Heiko Stuebner <heiko.stuebner@cherry.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/gpio.h>
+#include <linux/iopoll.h>
+#include <linux/math64.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+
+#include <drm/bridge/dw_mipi_dsi2.h>
+
+#include <drm/display/drm_dsc.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_panel.h>
+#include <video/mipi_display.h>
+#include <video/videomode.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_simple_kms_helper.h>
+
+#include <uapi/linux/videodev2.h>
+
+#include "rockchip_drm_drv.h"
+#include "rockchip_drm_vop.h"
+
+#define PSEC_PER_SEC			1000000000000LL
+
+struct dsigrf_reg {
+	u16 offset;
+	u16 lsb;
+	u16 msb;
+};
+
+enum grf_reg_fields {
+	TXREQCLKHS_EN,
+	GATING_EN,
+	IPI_SHUTDN,
+	IPI_COLORM,
+	IPI_COLOR_DEPTH,
+	IPI_FORMAT,
+	MAX_FIELDS,
+};
+
+#define IPI_DEPTH_5_6_5_BITS		0x02
+#define IPI_DEPTH_6_BITS		0x03
+#define IPI_DEPTH_8_BITS		0x05
+#define IPI_DEPTH_10_BITS		0x06
+
+struct rockchip_dw_dsi2_chip_data {
+	u32 reg;
+	const struct dsigrf_reg *grf_regs;
+	unsigned long long max_bit_rate_per_lane;
+};
+
+struct dw_mipi_dsi2_rockchip {
+	struct device *dev;
+	struct rockchip_encoder encoder;
+	void __iomem *base;
+	struct clk *pclk;
+	struct clk *sys_clk;
+
+	unsigned int lane_mbps; /* per lane */
+	u32 format;
+
+	struct regmap *grf_regmap;
+	struct phy *phy;
+	union phy_configure_opts phy_opts;
+
+	struct dw_mipi_dsi2 *dmd;
+	struct dw_mipi_dsi2_plat_data pdata;
+	const struct rockchip_dw_dsi2_chip_data *cdata;
+};
+
+static inline struct dw_mipi_dsi2_rockchip *to_dsi2(struct drm_encoder *encoder)
+{
+	struct rockchip_encoder *rkencoder = to_rockchip_encoder(encoder);
+
+	return container_of(rkencoder, struct dw_mipi_dsi2_rockchip, encoder);
+}
+
+static void grf_field_write(struct dw_mipi_dsi2_rockchip *dsi2, enum grf_reg_fields index,
+			    unsigned int val)
+{
+	const struct dsigrf_reg *field = &dsi2->cdata->grf_regs[index];
+
+	if (!field)
+		return;
+
+	regmap_write(dsi2->grf_regmap, field->offset,
+		     (val << field->lsb) | (GENMASK(field->msb, field->lsb) << 16));
+}
+
+static int dw_mipi_dsi2_phy_init(void *priv_data)
+{
+	return 0;
+}
+
+static void dw_mipi_dsi2_phy_power_on(void *priv_data)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+	int ret;
+
+	ret = phy_set_mode(dsi2->phy, PHY_MODE_MIPI_DPHY);
+	if (ret) {
+		dev_err(dsi2->dev, "Failed to set phy mode: %d\n", ret);
+		return;
+	}
+
+	phy_configure(dsi2->phy, &dsi2->phy_opts);
+	phy_power_on(dsi2->phy);
+}
+
+static void dw_mipi_dsi2_phy_power_off(void *priv_data)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+
+	phy_power_off(dsi2->phy);
+}
+
+static int
+dw_mipi_dsi2_get_lane_mbps(void *priv_data, const struct drm_display_mode *mode,
+			   unsigned long mode_flags, u32 lanes, u32 format,
+			   unsigned int *lane_mbps)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+	u64 max_lane_rate, target_phyclk;
+	unsigned int lane_rate_kbps;
+	int bpp;
+
+	max_lane_rate = dsi2->cdata->max_bit_rate_per_lane;
+
+	dsi2->format = format;
+	bpp = mipi_dsi_pixel_format_to_bpp(format);
+	if (bpp < 0) {
+		dev_err(dsi2->dev, "failed to get bpp for pixel format %d\n", format);
+		return bpp;
+	}
+
+	lane_rate_kbps = mode->clock * bpp / lanes;
+
+	/*
+	 * Set BW a little larger only in video burst mode in
+	 * consideration of the protocol overhead and HS mode
+	 * switching to BLLP mode, take 1 / 0.9, since Mbps must
+	 * big than bandwidth of RGB
+	 */
+	if (mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		lane_rate_kbps = (lane_rate_kbps * 10) / 9;
+
+	if (lane_rate_kbps > max_lane_rate) {
+		dev_err(dsi2->dev, "DPHY clock frequency is out of range\n");
+		return -ERANGE;
+	}
+
+	dsi2->lane_mbps = lane_rate_kbps / 1000;
+	*lane_mbps = dsi2->lane_mbps;
+
+	if (dsi2->phy) {
+		target_phyclk = DIV_ROUND_CLOSEST_ULL(lane_rate_kbps * lanes * 1000, bpp);
+		phy_mipi_dphy_get_default_config(target_phyclk, bpp, lanes,
+						 &dsi2->phy_opts.mipi_dphy);
+	}
+
+	return 0;
+}
+
+static void dw_mipi_dsi2_phy_get_iface(void *priv_data, struct dw_mipi_dsi2_phy_iface *iface)
+{
+	/* PPI width is fixed to 16 bits in DCPHY */
+	iface->ppi_width = 16;
+	iface->phy_type = DW_MIPI_DSI2_DPHY;
+}
+
+static int
+dw_mipi_dsi2_phy_get_timing(void *priv_data, unsigned int lane_mbps,
+			    struct dw_mipi_dsi2_phy_timing *timing)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+	struct phy_configure_opts_mipi_dphy *cfg = &dsi2->phy_opts.mipi_dphy;
+	unsigned long long tmp, ui;
+	unsigned long long hstx_clk;
+
+	hstx_clk = DIV_ROUND_CLOSEST_ULL(dsi2->lane_mbps * USEC_PER_SEC, 16);
+
+	ui = ALIGN(PSEC_PER_SEC, hstx_clk);
+	do_div(ui, hstx_clk);
+
+	/* PHY_LP2HS_TIME = (TLPX + THS-PREPARE + THS-ZERO) / Tphy_hstx_clk */
+	tmp = cfg->lpx + cfg->hs_prepare + cfg->hs_zero;
+	tmp = DIV_ROUND_CLOSEST_ULL(tmp << 16, ui);
+	timing->data_lp2hs = tmp;
+
+	/* PHY_HS2LP_TIME = (THS-TRAIL + THS-EXIT) / Tphy_hstx_clk */
+	tmp = cfg->hs_trail + cfg->hs_exit;
+	tmp = DIV_ROUND_CLOSEST_ULL(tmp << 16, ui);
+	timing->data_hs2lp = tmp;
+
+	return 0;
+}
+
+static const struct dw_mipi_dsi2_phy_ops dw_mipi_dsi2_rockchip_phy_ops = {
+	.init = dw_mipi_dsi2_phy_init,
+	.power_on = dw_mipi_dsi2_phy_power_on,
+	.power_off = dw_mipi_dsi2_phy_power_off,
+	.get_interface = dw_mipi_dsi2_phy_get_iface,
+	.get_lane_mbps = dw_mipi_dsi2_get_lane_mbps,
+	.get_timing = dw_mipi_dsi2_phy_get_timing,
+};
+
+static void dw_mipi_dsi2_encoder_atomic_enable(struct drm_encoder *encoder,
+					       struct drm_atomic_state *state)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = to_dsi2(encoder);
+	u32 color_depth;
+
+	switch (dsi2->format) {
+	case MIPI_DSI_FMT_RGB666:
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		color_depth = IPI_DEPTH_6_BITS;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		color_depth = IPI_DEPTH_5_6_5_BITS;
+		break;
+	case MIPI_DSI_FMT_RGB888:
+		color_depth = IPI_DEPTH_8_BITS;
+		break;
+	default:
+		/* Should've been caught by atomic_check */
+		WARN_ON(1);
+		return;
+	}
+
+	grf_field_write(dsi2, IPI_COLOR_DEPTH, color_depth);
+}
+
+static int
+dw_mipi_dsi2_encoder_atomic_check(struct drm_encoder *encoder,
+				  struct drm_crtc_state *crtc_state,
+				  struct drm_connector_state *conn_state)
+{
+	struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state);
+	struct dw_mipi_dsi2_rockchip *dsi2 = to_dsi2(encoder);
+	struct drm_connector *connector = conn_state->connector;
+	struct drm_display_info *info = &connector->display_info;
+
+	switch (dsi2->format) {
+	case MIPI_DSI_FMT_RGB666:
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		s->output_mode = ROCKCHIP_OUT_MODE_P666;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		s->output_mode = ROCKCHIP_OUT_MODE_P565;
+		break;
+	case MIPI_DSI_FMT_RGB888:
+		s->output_mode = ROCKCHIP_OUT_MODE_P888;
+		break;
+	default:
+		WARN_ON(1);
+		return -EINVAL;
+	}
+
+	if (info->num_bus_formats)
+		s->bus_format = info->bus_formats[0];
+	else
+		s->bus_format = MEDIA_BUS_FMT_RGB888_1X24;
+
+	s->output_type = DRM_MODE_CONNECTOR_DSI;
+	s->bus_flags = info->bus_flags;
+	s->color_space = V4L2_COLORSPACE_DEFAULT;
+
+	return 0;
+}
+
+static const struct drm_encoder_helper_funcs
+dw_mipi_dsi2_encoder_helper_funcs = {
+	.atomic_enable = dw_mipi_dsi2_encoder_atomic_enable,
+	.atomic_check = dw_mipi_dsi2_encoder_atomic_check,
+};
+
+static int rockchip_dsi2_drm_create_encoder(struct dw_mipi_dsi2_rockchip *dsi2,
+					    struct drm_device *drm_dev)
+{
+	struct drm_encoder *encoder = &dsi2->encoder.encoder;
+	int ret;
+
+	encoder->possible_crtcs = drm_of_find_possible_crtcs(drm_dev,
+							     dsi2->dev->of_node);
+
+	ret = drm_simple_encoder_init(drm_dev, encoder, DRM_MODE_ENCODER_DSI);
+	if (ret) {
+		dev_err(dsi2->dev, "Failed to initialize encoder with drm\n");
+		return ret;
+	}
+
+	drm_encoder_helper_add(encoder, &dw_mipi_dsi2_encoder_helper_funcs);
+
+	return 0;
+}
+
+static int dw_mipi_dsi2_rockchip_bind(struct device *dev, struct device *master,
+				      void *data)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = dev_get_drvdata(dev);
+	struct drm_device *drm_dev = data;
+	int ret;
+
+	ret = rockchip_dsi2_drm_create_encoder(dsi2, drm_dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to create drm encoder\n");
+
+	rockchip_drm_encoder_set_crtc_endpoint_id(&dsi2->encoder,
+						  dev->of_node, 0, 0);
+
+	ret = dw_mipi_dsi2_bind(dsi2->dmd, &dsi2->encoder.encoder);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to bind\n");
+
+	return 0;
+}
+
+static void dw_mipi_dsi2_rockchip_unbind(struct device *dev, struct device *master,
+					 void *data)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = dev_get_drvdata(dev);
+
+	dw_mipi_dsi2_unbind(dsi2->dmd);
+}
+
+static const struct component_ops dw_mipi_dsi2_rockchip_ops = {
+	.bind	= dw_mipi_dsi2_rockchip_bind,
+	.unbind	= dw_mipi_dsi2_rockchip_unbind,
+};
+
+static int dw_mipi_dsi2_rockchip_host_attach(void *priv_data,
+					     struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+	int ret;
+
+	ret = component_add(dsi2->dev, &dw_mipi_dsi2_rockchip_ops);
+	if (ret)
+		return dev_err_probe(dsi2->dev, ret, "Failed to register component\n");
+
+	return 0;
+}
+
+static int dw_mipi_dsi2_rockchip_host_detach(void *priv_data,
+					     struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = priv_data;
+
+	component_del(dsi2->dev, &dw_mipi_dsi2_rockchip_ops);
+
+	return 0;
+}
+
+static const struct dw_mipi_dsi2_host_ops dw_mipi_dsi2_rockchip_host_ops = {
+	.attach = dw_mipi_dsi2_rockchip_host_attach,
+	.detach = dw_mipi_dsi2_rockchip_host_detach,
+};
+
+static __maybe_unused int dw_mipi_dsi2_runtime_suspend(struct device *dev)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(dsi2->pclk);
+	clk_disable_unprepare(dsi2->sys_clk);
+
+	return 0;
+}
+
+static __maybe_unused int dw_mipi_dsi2_runtime_resume(struct device *dev)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = dev_get_drvdata(dev);
+
+	clk_prepare_enable(dsi2->pclk);
+	clk_prepare_enable(dsi2->sys_clk);
+
+	return 0;
+}
+
+static const struct dev_pm_ops dw_mipi_dsi2_rockchip_pm_ops = {
+	SET_RUNTIME_PM_OPS(dw_mipi_dsi2_runtime_suspend,
+			   dw_mipi_dsi2_runtime_resume, NULL)
+};
+
+static int dw_mipi_dsi2_rockchip_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	const struct rockchip_dw_dsi2_chip_data *cdata =
+						of_device_get_match_data(dev);
+	struct dw_mipi_dsi2_rockchip *dsi2;
+	struct resource *res;
+	int i;
+
+	dsi2 = devm_kzalloc(dev, sizeof(*dsi2), GFP_KERNEL);
+	if (!dsi2)
+		return -ENOMEM;
+
+	dsi2->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(dsi2->base))
+		return dev_err_probe(dev, PTR_ERR(dsi2->base), "Unable to get dsi registers\n");
+
+	i = 0;
+	while (cdata[i].reg) {
+		if (cdata[i].reg == res->start) {
+			dsi2->cdata = &cdata[i];
+			break;
+		}
+
+		i++;
+	}
+
+	if (!dsi2->cdata)
+		return dev_err_probe(dev, -EINVAL, "No dsi-config for %s node\n", np->name);
+
+	dsi2->pclk = devm_clk_get(dev, "pclk");
+	if (IS_ERR(dsi2->pclk))
+		return dev_err_probe(dev, PTR_ERR(dsi2->pclk), "Unable to get pclk\n");
+
+	dsi2->sys_clk = devm_clk_get(dev, "sys");
+	if (IS_ERR(dsi2->sys_clk))
+		return dev_err_probe(dev, PTR_ERR(dsi2->sys_clk), "Unable to get sys_clk\n");
+
+	dsi2->grf_regmap = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
+	if (IS_ERR(dsi2->grf_regmap))
+		return dev_err_probe(dsi2->dev, PTR_ERR(dsi2->grf_regmap), "Unable to get grf\n");
+
+	dsi2->phy = devm_phy_optional_get(dev, "dcphy");
+	if (IS_ERR(dsi2->phy))
+		return dev_err_probe(dev, PTR_ERR(dsi2->phy), "failed to get mipi phy\n");
+
+	dsi2->dev = dev;
+	dsi2->pdata.base = dsi2->base;
+	dsi2->pdata.max_data_lanes = 4;
+	dsi2->pdata.phy_ops = &dw_mipi_dsi2_rockchip_phy_ops;
+	dsi2->pdata.host_ops = &dw_mipi_dsi2_rockchip_host_ops;
+	dsi2->pdata.priv_data = dsi2;
+	platform_set_drvdata(pdev, dsi2);
+
+	dsi2->dmd = dw_mipi_dsi2_probe(pdev, &dsi2->pdata);
+	if (IS_ERR(dsi2->dmd))
+		return dev_err_probe(dev, PTR_ERR(dsi2->dmd), "Failed to probe dw_mipi_dsi2\n");
+
+	return 0;
+}
+
+static void dw_mipi_dsi2_rockchip_remove(struct platform_device *pdev)
+{
+	struct dw_mipi_dsi2_rockchip *dsi2 = platform_get_drvdata(pdev);
+
+	dw_mipi_dsi2_remove(dsi2->dmd);
+}
+
+static const struct dsigrf_reg rk3588_dsi0_grf_reg_fields[MAX_FIELDS] = {
+	[TXREQCLKHS_EN]		= { 0x0000, 11, 11 },
+	[GATING_EN]		= { 0x0000, 10, 10 },
+	[IPI_SHUTDN]		= { 0x0000,  9,  9 },
+	[IPI_COLORM]		= { 0x0000,  8,  8 },
+	[IPI_COLOR_DEPTH]	= { 0x0000,  4,  7 },
+	[IPI_FORMAT]		= { 0x0000,  0,  3 },
+};
+
+static const struct dsigrf_reg rk3588_dsi1_grf_reg_fields[MAX_FIELDS] = {
+	[TXREQCLKHS_EN]		= { 0x0004, 11, 11 },
+	[GATING_EN]		= { 0x0004, 10, 10 },
+	[IPI_SHUTDN]		= { 0x0004,  9,  9 },
+	[IPI_COLORM]		= { 0x0004,  8,  8 },
+	[IPI_COLOR_DEPTH]	= { 0x0004,  4,  7 },
+	[IPI_FORMAT]		= { 0x0004,  0,  3 },
+};
+
+static const struct rockchip_dw_dsi2_chip_data rk3588_chip_data[] = {
+	{
+		.reg = 0xfde20000,
+		.grf_regs = rk3588_dsi0_grf_reg_fields,
+		.max_bit_rate_per_lane = 4500000ULL,
+	},
+	{
+		.reg = 0xfde30000,
+		.grf_regs = rk3588_dsi1_grf_reg_fields,
+		.max_bit_rate_per_lane = 4500000ULL,
+	}
+};
+
+static const struct of_device_id dw_mipi_dsi2_rockchip_dt_ids[] = {
+	{
+		.compatible = "rockchip,rk3588-mipi-dsi2",
+		.data = &rk3588_chip_data,
+	},
+	{}
+};
+MODULE_DEVICE_TABLE(of, dw_mipi_dsi2_rockchip_dt_ids);
+
+struct platform_driver dw_mipi_dsi2_rockchip_driver = {
+	.probe	= dw_mipi_dsi2_rockchip_probe,
+	.remove = dw_mipi_dsi2_rockchip_remove,
+	.driver = {
+		.of_match_table = dw_mipi_dsi2_rockchip_dt_ids,
+		.pm = &dw_mipi_dsi2_rockchip_pm_ops,
+		.name = "dw-mipi-dsi2",
+	},
+};
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
index ddf0be331c0a..5327ce035003 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
@@ -511,6 +511,8 @@ static int __init rockchip_drm_init(void)
 				CONFIG_ROCKCHIP_DW_HDMI_QP);
 	ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi_rockchip_driver,
 				CONFIG_ROCKCHIP_DW_MIPI_DSI);
+	ADD_ROCKCHIP_SUB_DRIVER(dw_mipi_dsi2_rockchip_driver,
+				CONFIG_ROCKCHIP_DW_MIPI_DSI2);
 	ADD_ROCKCHIP_SUB_DRIVER(inno_hdmi_driver, CONFIG_ROCKCHIP_INNO_HDMI);
 	ADD_ROCKCHIP_SUB_DRIVER(rk3066_hdmi_driver,
 				CONFIG_ROCKCHIP_RK3066_HDMI);
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
index 24b4ce5ceaf1..9c9d38a06cdf 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
@@ -90,6 +90,7 @@ extern struct platform_driver cdn_dp_driver;
 extern struct platform_driver dw_hdmi_rockchip_pltfm_driver;
 extern struct platform_driver dw_hdmi_qp_rockchip_pltfm_driver;
 extern struct platform_driver dw_mipi_dsi_rockchip_driver;
+extern struct platform_driver dw_mipi_dsi2_rockchip_driver;
 extern struct platform_driver inno_hdmi_driver;
 extern struct platform_driver rockchip_dp_driver;
 extern struct platform_driver rockchip_lvds_driver;
-- 
2.45.2

Re: [PATCH 1/3] drm/bridge/synopsys: Add MIPI DSI2 host controller bridge

[Diederik de Haas]

[-- Attachment #1: Type: text/plain, Size: 3309 bytes --]

On Wed Nov 6, 2024 at 1:33 PM CET, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
>
> Add a Synopsys Designware MIPI DSI host DRM bridge driver for their
> DSI2 host controller, based on the Rockchip version from the driver
> rockchip/dw-mipi-dsi2.c in their vendor-kernel with phy & bridge APIs.
>
> While the driver is heavily modelled after the previous IP, the register
> set of this DSI2 controller is completely different and there are also
> additional properties like the variable-width phy interface.
>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
> ---
>  drivers/gpu/drm/bridge/synopsys/Kconfig       |    6 +
>  drivers/gpu/drm/bridge/synopsys/Makefile      |    1 +
>  .../gpu/drm/bridge/synopsys/dw-mipi-dsi2.c    | 1034 +++++++++++++++++
>  include/drm/bridge/dw_mipi_dsi2.h             |   94 ++
>  4 files changed, 1135 insertions(+)
>  create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
>  create mode 100644 include/drm/bridge/dw_mipi_dsi2.h
>
> diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
> index ca416dab156d..f3ab2f985f8c 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Kconfig
> +++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
> @@ -59,3 +59,9 @@ config DRM_DW_MIPI_DSI
>  	select DRM_KMS_HELPER
>  	select DRM_MIPI_DSI
>  	select DRM_PANEL_BRIDGE
> +
> +config DRM_DW_MIPI_DSI2
> +	tristate
> +	select DRM_KMS_HELPER
> +	select DRM_MIPI_DSI
> +	select DRM_PANEL_BRIDGE
> diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
> index 9869d9651ed1..9dc376d220ad 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Makefile
> +++ b/drivers/gpu/drm/bridge/synopsys/Makefile
> @@ -8,3 +8,4 @@ obj-$(CONFIG_DRM_DW_HDMI_CEC) += dw-hdmi-cec.o
>  obj-$(CONFIG_DRM_DW_HDMI_QP) += dw-hdmi-qp.o
>  
>  obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
> +obj-$(CONFIG_DRM_DW_MIPI_DSI2) += dw-mipi-dsi2.o
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
> new file mode 100644
> index 000000000000..43738fe3cb93
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
> @@ -0,0 +1,1034 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2024, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * Modified by Heiko Stuebner <heiko.stuebner@cherry.de>
> + * This generic Synopsys DesignWare MIPI DSI2 host driver is based on the
> + * Rockchip version from rockchip/dw-mipi-dsi2.c converted to use bridge APIs.
> + */
> +
> +#include <linux/clk.h>
> ...
> +#include <drm/drm_print.h>
> +
> +#define UPDATE(v, h, l)			(((v) << (l)) & GENMASK((h), (l)))
> +
> +#define DSI2_PWR_UP			0x000c
> ...
> +#define DSI2_MAX_REGISGER		DSI2_INT_FORCE_CRI
> +
> +#define MODE_STATUS_TIMEOUT_US		10000
> +#define CMD_PKT_STATUS_TIMEOUT_US	20000
> +
> +enum vid_mode_type {
> +	VID_MODE_TYPE_NON_BURST_SYNC_PULSES,
> +	VID_MODE_TYPE_NON_BURST_SYNC_EVENTS,
> +	VID_MODE_TYPE_BURST,
> +};
> +
> +enum mode_ctrl {
> +	IDLE_MODE,
> +	AUTOCALC_MODE,
> +	COMMAND_MODE,
> +	VIDEO_MODE,
> +	DATA_STREAM_MODE,
> +	VIDE_TEST_MODE,

VIDEO_TEST_MODE ?

> +	DATA_STREAM_TEST_MODE,
> +};

Cheers,
  Diederik

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 3/3] drm/rockchip: Add MIPI DSI2 glue driver for RK3588

[Diederik de Haas]

[-- Attachment #1: Type: text/plain, Size: 5690 bytes --]

On Wed Nov 6, 2024 at 1:33 PM CET, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
>
> This adds the glue code for the MIPI DSI2 bridge on Rockchip SoCs and
> enables its use on the RK3588.
>
> Right now the DSI2 controller is always paired with a DC-phy based on a
> Samsung IP, so the interface values are set statically for now.
> This stays true for the upcoming RK3576 as well.
>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
> ---
>  drivers/gpu/drm/rockchip/Kconfig              |  10 +
>  drivers/gpu/drm/rockchip/Makefile             |   1 +
>  .../gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c  | 524 ++++++++++++++++++
>  drivers/gpu/drm/rockchip/rockchip_drm_drv.c   |   2 +
>  drivers/gpu/drm/rockchip/rockchip_drm_drv.h   |   1 +
>  5 files changed, 538 insertions(+)
>  create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
>
> diff --git a/drivers/gpu/drm/rockchip/Kconfig b/drivers/gpu/drm/rockchip/Kconfig
> index 448fadd4ba15..99d4b260de85 100644
> --- a/drivers/gpu/drm/rockchip/Kconfig
> +++ b/drivers/gpu/drm/rockchip/Kconfig
> @@ -10,6 +10,7 @@ config DRM_ROCKCHIP
>  	select DRM_DW_HDMI if ROCKCHIP_DW_HDMI
>  	select DRM_DW_HDMI_QP if ROCKCHIP_DW_HDMI_QP
>  	select DRM_DW_MIPI_DSI if ROCKCHIP_DW_MIPI_DSI
> +	select DRM_DW_MIPI_DSI2 if ROCKCHIP_DW_MIPI_DSI2
>  	select GENERIC_PHY if ROCKCHIP_DW_MIPI_DSI
>  	select GENERIC_PHY_MIPI_DPHY if ROCKCHIP_DW_MIPI_DSI
>  	select SND_SOC_HDMI_CODEC if ROCKCHIP_CDN_DP && SND_SOC
> @@ -81,6 +82,15 @@ config ROCKCHIP_DW_MIPI_DSI
>  	  enable MIPI DSI on RK3288 or RK3399 based SoC, you should
>  	  select this option.
>  
> +config ROCKCHIP_DW_MIPI_DSI2
> +	bool "Rockchip specific extensions for Synopsys DW MIPI DSI"
> +	select GENERIC_PHY_MIPI_DPHY
> +	help
> +	  This selects support for Rockchip SoC specific extensions
> +	  for the Synopsys DesignWare dsi driver. If you want to
> +	  enable MIPI DSI on RK3288 or RK3399 based SoC, you should
> +	  select this option.

The commit message and the cover letter talk about RK3588 (and RK3576),
so this seems like a copy-n-paste error (from DSI '1')?
I'd also prefer 'dsi' to be in capitals (thus 'DSI').

> +
>  config ROCKCHIP_INNO_HDMI
>  	bool "Rockchip specific extensions for Innosilicon HDMI"
>  	select DRM_DISPLAY_HDMI_HELPER
> diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
> index 3eab662a5a1d..2b867cebbc12 100644
> --- a/drivers/gpu/drm/rockchip/Makefile
> +++ b/drivers/gpu/drm/rockchip/Makefile
> @@ -13,6 +13,7 @@ rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI_QP) += dw_hdmi_qp-rockchip.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi-rockchip.o
> +rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI2) += dw-mipi-dsi2-rockchip.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_LVDS) += rockchip_lvds.o
>  rockchipdrm-$(CONFIG_ROCKCHIP_RGB) += rockchip_rgb.o
> diff --git a/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c b/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
> new file mode 100644
> index 000000000000..42a7a80e2138
> --- /dev/null
> +++ b/drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
> @@ -0,0 +1,524 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2024 Rockchip Electronics Co.Ltd
> + * Author:
> + *      Guochun Huang <hero.huang@rock-chips.com>
> + *      Heiko Stuebner <heiko.stuebner@cherry.de>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/component.h>
> +#include <linux/gpio.h>
> +#include <linux/iopoll.h>
> +#include <linux/math64.h>
> +#include <linux/media-bus-format.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_platform.h>

In commit 722d4f06e560 ("drm: Explicitly include correct DT includes")
several changes were made to header includes.
One of the things I noticed is that ``of_device.h`` often was removed
and ``of.h`` added.
Thus are the above headers as they should be or should they be updated
like was done in commit 722d4f06e560?

> +#include <linux/pm_runtime.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/phy/phy.h>
> +
> +#include <drm/bridge/dw_mipi_dsi2.h>
> +
> +#include <drm/display/drm_dsc.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <video/mipi_display.h>
> +#include <video/videomode.h>
> +#include <drm/drm_connector.h>
> +#include <drm/drm_probe_helper.h>
> +#include <drm/drm_simple_kms_helper.h>
> +
> +#include <uapi/linux/videodev2.h>
> +
> +#include "rockchip_drm_drv.h"
> +#include "rockchip_drm_vop.h"
> +
> +#define PSEC_PER_SEC			1000000000000LL
> +
> +struct dsigrf_reg {
> +	u16 offset;
> +	u16 lsb;
> +	u16 msb;
> +};
> +
> +enum grf_reg_fields {
> +	TXREQCLKHS_EN,
> +	GATING_EN,
> +	IPI_SHUTDN,
> +	IPI_COLORM,
> +	IPI_COLOR_DEPTH,
> +	IPI_FORMAT,
> +	MAX_FIELDS,
> +};
> +
> +#define IPI_DEPTH_5_6_5_BITS		0x02
> +#define IPI_DEPTH_6_BITS		0x03
> +#define IPI_DEPTH_8_BITS		0x05
> +#define IPI_DEPTH_10_BITS		0x06

Possibly dumb remark (sorry):
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c also defines these
values, so wouldn't it be better if they're defined in 1 place?

Cheers,
  Diederik

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 2/3] dt-bindings: display: rockchip: Add schema for RK3588 DW DSI2 controller

[Rob Herring (Arm)]

On Wed, 06 Nov 2024 13:33:03 +0100, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> The Display Serial Interface 2 (DSI-2) is part of a group of communication
> protocols defined by the MIPI Alliance. The RK3588 implements this
> specification in its two MIPI DSI-2 Host Controllers that are based on a
> new Synopsis IP.
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
> ---
>  .../rockchip/rockchip,rk3588-mipi-dsi2.yaml   | 119 ++++++++++++++++++
>  1 file changed, 119 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml: $id: Cannot determine base path from $id, relative path/filename doesn't match actual path or filename
 	 $id: http://devicetree.org/schemas/display/rockchip/rockchip,dw-mipi-dsi2.yaml
 	file: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241106123304.422854-3-heiko@sntech.de

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH 1/3] drm/bridge/synopsys: Add MIPI DSI2 host controller bridge

[neil.armstrong]

Hi,

On 06/11/2024 13:33, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> Add a Synopsys Designware MIPI DSI host DRM bridge driver for their
> DSI2 host controller, based on the Rockchip version from the driver
> rockchip/dw-mipi-dsi2.c in their vendor-kernel with phy & bridge APIs.
> 
> While the driver is heavily modelled after the previous IP, the register
> set of this DSI2 controller is completely different and there are also
> additional properties like the variable-width phy interface.
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
> ---
>   drivers/gpu/drm/bridge/synopsys/Kconfig       |    6 +
>   drivers/gpu/drm/bridge/synopsys/Makefile      |    1 +
>   .../gpu/drm/bridge/synopsys/dw-mipi-dsi2.c    | 1034 +++++++++++++++++
>   include/drm/bridge/dw_mipi_dsi2.h             |   94 ++
>   4 files changed, 1135 insertions(+)
>   create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
>   create mode 100644 include/drm/bridge/dw_mipi_dsi2.h
> 
> diff --git a/drivers/gpu/drm/bridge/synopsys/Kconfig b/drivers/gpu/drm/bridge/synopsys/Kconfig
> index ca416dab156d..f3ab2f985f8c 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Kconfig
> +++ b/drivers/gpu/drm/bridge/synopsys/Kconfig
> @@ -59,3 +59,9 @@ config DRM_DW_MIPI_DSI
>   	select DRM_KMS_HELPER
>   	select DRM_MIPI_DSI
>   	select DRM_PANEL_BRIDGE
> +
> +config DRM_DW_MIPI_DSI2
> +	tristate
> +	select DRM_KMS_HELPER
> +	select DRM_MIPI_DSI
> +	select DRM_PANEL_BRIDGE
> diff --git a/drivers/gpu/drm/bridge/synopsys/Makefile b/drivers/gpu/drm/bridge/synopsys/Makefile
> index 9869d9651ed1..9dc376d220ad 100644
> --- a/drivers/gpu/drm/bridge/synopsys/Makefile
> +++ b/drivers/gpu/drm/bridge/synopsys/Makefile
> @@ -8,3 +8,4 @@ obj-$(CONFIG_DRM_DW_HDMI_CEC) += dw-hdmi-cec.o
>   obj-$(CONFIG_DRM_DW_HDMI_QP) += dw-hdmi-qp.o
>   
>   obj-$(CONFIG_DRM_DW_MIPI_DSI) += dw-mipi-dsi.o
> +obj-$(CONFIG_DRM_DW_MIPI_DSI2) += dw-mipi-dsi2.o
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
> new file mode 100644
> index 000000000000..43738fe3cb93
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
> @@ -0,0 +1,1034 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2024, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * Modified by Heiko Stuebner <heiko.stuebner@cherry.de>
> + * This generic Synopsys DesignWare MIPI DSI2 host driver is based on the
> + * Rockchip version from rockchip/dw-mipi-dsi2.c converted to use bridge APIs.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/iopoll.h>
> +#include <linux/media-bus-format.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/reset.h>
> +
> +#include <video/mipi_display.h>
> +
> +#include <drm/bridge/dw_mipi_dsi2.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_bridge.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_of.h>
> +#include <drm/drm_print.h>
> +
> +#define UPDATE(v, h, l)			(((v) << (l)) & GENMASK((h), (l)))

I'm not super fan of this macro, overall I thinkg you should switch to
regmap and make use of regmap_update_bits and drop dsi2_write/read wrappers
to readl/writel.

> +
> +#define DSI2_PWR_UP			0x000c
> +#define RESET				0
> +#define POWER_UP			BIT(0)
> +#define CMD_TX_MODE(x)			UPDATE(x,  24,  24)
> +#define DSI2_SOFT_RESET			0x0010
> +#define SYS_RSTN			BIT(2)
> +#define PHY_RSTN			BIT(1)
> +#define IPI_RSTN			BIT(0)
> +#define INT_ST_MAIN			0x0014
> +#define DSI2_MODE_CTRL			0x0018
> +#define DSI2_MODE_STATUS		0x001c
> +#define DSI2_CORE_STATUS		0x0020
> +#define PRI_RD_DATA_AVAIL		BIT(26)
> +#define PRI_FIFOS_NOT_EMPTY		BIT(25)
> +#define PRI_BUSY			BIT(24)
> +#define CRI_RD_DATA_AVAIL		BIT(18)
> +#define CRT_FIFOS_NOT_EMPTY		BIT(17)
> +#define CRI_BUSY			BIT(16)
> +#define IPI_FIFOS_NOT_EMPTY		BIT(9)
> +#define IPI_BUSY			BIT(8)
> +#define CORE_FIFOS_NOT_EMPTY		BIT(1)
> +#define CORE_BUSY			BIT(0)
> +#define MANUAL_MODE_CFG			0x0024
> +#define MANUAL_MODE_EN			BIT(0)
> +#define DSI2_TIMEOUT_HSTX_CFG		0x0048
> +#define TO_HSTX(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_HSTXRDY_CFG	0x004c
> +#define TO_HSTXRDY(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_LPRX_CFG		0x0050
> +#define TO_LPRXRDY(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_LPTXRDY_CFG	0x0054
> +#define TO_LPTXRDY(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_LPTXTRIG_CFG	0x0058
> +#define TO_LPTXTRIG(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_LPTXULPS_CFG	0x005c
> +#define TO_LPTXULPS(x)			UPDATE(x, 15, 0)
> +#define DSI2_TIMEOUT_BTA_CFG		0x60
> +#define TO_BTA(x)			UPDATE(x, 15, 0)
> +

<snip>

> +
> +static struct dw_mipi_dsi2 *
> +__dw_mipi_dsi2_probe(struct platform_device *pdev,
> +		     const struct dw_mipi_dsi2_plat_data *plat_data)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct reset_control *apb_rst;
> +	struct dw_mipi_dsi2 *dsi2;
> +	int ret;
> +
> +	dsi2 = devm_kzalloc(dev, sizeof(*dsi2), GFP_KERNEL);
> +	if (!dsi2)
> +		return ERR_PTR(-ENOMEM);
> +
> +	dsi2->dev = dev;
> +	dsi2->plat_data = plat_data;
> +
> +	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps ||
> +	    !plat_data->phy_ops->get_timing)
> +		return dev_err_ptr_probe(dev, -ENODEV, "Phy not properly configured\n");
> +
> +	if (!plat_data->base) {
> +		dsi2->base = devm_platform_ioremap_resource(pdev, 0);
> +		if (IS_ERR(dsi2->base))
> +			return ERR_PTR(-ENODEV);
> +	} else {
> +		dsi2->base = plat_data->base;
> +	}
> +
> +	dsi2->pclk = devm_clk_get(dev, "pclk");
> +	if (IS_ERR(dsi2->pclk))
> +		return dev_err_cast_probe(dev, dsi2->pclk, "Unable to get pclk\n");
> +
> +	dsi2->sys_clk = devm_clk_get(dev, "sys");
> +	if (IS_ERR(dsi2->sys_clk))
> +		return dev_err_cast_probe(dev, dsi2->sys_clk, "Unable to get sys_clk\n");
> +
> +	/*
> +	 * Note that the reset was not defined in the initial device tree, so
> +	 * we have to be prepared for it not being found.
> +	 */
> +	apb_rst = devm_reset_control_get_optional_exclusive(dev, "apb");
> +	if (IS_ERR(apb_rst))
> +		return dev_err_cast_probe(dev, apb_rst, "Unable to get reset control\n");
> +
> +	if (apb_rst) {
> +		ret = clk_prepare_enable(dsi2->pclk);
> +		if (ret) {
> +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> +			return ERR_PTR(ret);
> +		}
> +
> +		reset_control_assert(apb_rst);
> +		usleep_range(10, 20);
> +		reset_control_deassert(apb_rst);
> +
> +		clk_disable_unprepare(dsi2->pclk);
> +	}
> +
> +	pm_runtime_enable(dev);
> +
> +	dsi2->dsi_host.ops = &dw_mipi_dsi2_host_ops;
> +	dsi2->dsi_host.dev = dev;
> +	ret = mipi_dsi_host_register(&dsi2->dsi_host);
> +	if (ret) {
> +		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
> +		pm_runtime_disable(dev);
> +		return ERR_PTR(ret);
> +	}
> +
> +	dsi2->bridge.driver_private = dsi2;
> +	dsi2->bridge.funcs = &dw_mipi_dsi2_bridge_funcs;
> +	dsi2->bridge.of_node = pdev->dev.of_node;
> +
> +	return dsi2;
> +}
> +
> +static void __dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
> +{
> +	mipi_dsi_host_unregister(&dsi2->dsi_host);
> +
> +	pm_runtime_disable(dsi2->dev);
> +}
> +
> +/*
> + * Probe/remove API, used from platforms based on the DRM bridge API.
> + */
> +struct dw_mipi_dsi2 *
> +dw_mipi_dsi2_probe(struct platform_device *pdev,
> +		   const struct dw_mipi_dsi2_plat_data *plat_data)
> +{
> +	return __dw_mipi_dsi2_probe(pdev, plat_data);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_probe);
> +
> +void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
> +{
> +	__dw_mipi_dsi2_remove(dsi2);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_remove);

Since it's not use yet, you should probably drop those since it's dead
code.

> +
> +/*
> + * Bind/unbind API, used from platforms based on the component framework.
> + */
> +int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder)
> +{
> +	return drm_bridge_attach(encoder, &dsi2->bridge, NULL, 0);
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_bind);
> +
> +void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2)
> +{
> +}
> +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_unbind);
> +
> +MODULE_AUTHOR("Guochun Huang <hero.huang@rock-chips.com>");
> +MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@cherry.de>");
> +MODULE_DESCRIPTION("DW MIPI DSI2 host controller driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:dw-mipi-dsi2");
> diff --git a/include/drm/bridge/dw_mipi_dsi2.h b/include/drm/bridge/dw_mipi_dsi2.h
> new file mode 100644
> index 000000000000..ef5479b35028
> --- /dev/null
> +++ b/include/drm/bridge/dw_mipi_dsi2.h
> @@ -0,0 +1,94 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Copyright (c) 2024, Fuzhou Rockchip Electronics Co., Ltd
> + *
> + * Authors: Guochun Huang <hero.huang@rock-chips.com>
> + *          Heiko Stuebner <heiko.stuebner@cherry.de>
> + */
> +
> +#ifndef __DW_MIPI_DSI2__
> +#define __DW_MIPI_DSI2__
> +
> +#include <linux/types.h>
> +
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_bridge.h>
> +#include <drm/drm_connector.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_modes.h>
> +
> +struct drm_display_mode;
> +struct drm_encoder;
> +struct dw_mipi_dsi2;
> +struct mipi_dsi_device;
> +struct platform_device;
> +
> +enum dw_mipi_dsi2_phy_type {
> +	DW_MIPI_DSI2_DPHY,
> +	DW_MIPI_DSI2_CPHY,
> +};
> +
> +struct dw_mipi_dsi2_phy_iface {
> +	int ppi_width;
> +	enum dw_mipi_dsi2_phy_type phy_type;
> +};
> +
> +struct dw_mipi_dsi2_phy_timing {
> +	u32 data_hs2lp;
> +	u32 data_lp2hs;
> +};
> +
> +struct dw_mipi_dsi2_phy_ops {
> +	int (*init)(void *priv_data);
> +	void (*power_on)(void *priv_data);
> +	void (*power_off)(void *priv_data);
> +	void (*get_interface)(void *priv_data, struct dw_mipi_dsi2_phy_iface *iface);
> +	int (*get_lane_mbps)(void *priv_data,
> +			     const struct drm_display_mode *mode,
> +			     unsigned long mode_flags, u32 lanes, u32 format,
> +			     unsigned int *lane_mbps);
> +	int (*get_timing)(void *priv_data, unsigned int lane_mbps,
> +			  struct dw_mipi_dsi2_phy_timing *timing);
> +	int (*get_esc_clk_rate)(void *priv_data, unsigned int *esc_clk_rate);
> +};
> +
> +struct dw_mipi_dsi2_host_ops {
> +	int (*attach)(void *priv_data,
> +		      struct mipi_dsi_device *dsi);
> +	int (*detach)(void *priv_data,
> +		      struct mipi_dsi_device *dsi);
> +};
> +
> +struct dw_mipi_dsi2_plat_data {
> +	void __iomem *base;
> +	unsigned int max_data_lanes;
> +
> +	enum drm_mode_status (*mode_valid)(void *priv_data,
> +					   const struct drm_display_mode *mode,
> +					   unsigned long mode_flags,
> +					   u32 lanes, u32 format);
> +
> +	bool (*mode_fixup)(void *priv_data, const struct drm_display_mode *mode,
> +			   struct drm_display_mode *adjusted_mode);
> +
> +	u32 *(*get_input_bus_fmts)(void *priv_data,
> +				   struct drm_bridge *bridge,
> +				   struct drm_bridge_state *bridge_state,
> +				   struct drm_crtc_state *crtc_state,
> +				   struct drm_connector_state *conn_state,
> +				   u32 output_fmt,
> +				   unsigned int *num_input_fmts);
> +
> +	const struct dw_mipi_dsi2_phy_ops *phy_ops;
> +	const struct dw_mipi_dsi2_host_ops *host_ops;
> +
> +	void *priv_data;
> +};
> +
> +struct dw_mipi_dsi2 *dw_mipi_dsi2_probe(struct platform_device *pdev,
> +					const struct dw_mipi_dsi2_plat_data *plat_data);
> +void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2);
> +int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder);
> +void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2);
> +
> +#endif /* __DW_MIPI_DSI2__ */

Overall the driver is very close to dw-mipi-dsi, si it's overall good!

Thanks,
Neil

Re: [PATCH 2/3] dt-bindings: display: rockchip: Add schema for RK3588 DW DSI2 controller

[Rob Herring]

On Wed, Nov 06, 2024 at 01:33:03PM +0100, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> The Display Serial Interface 2 (DSI-2) is part of a group of communication
> protocols defined by the MIPI Alliance. The RK3588 implements this
> specification in its two MIPI DSI-2 Host Controllers that are based on a
> new Synopsis IP.
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
> ---
>  .../rockchip/rockchip,rk3588-mipi-dsi2.yaml   | 119 ++++++++++++++++++
>  1 file changed, 119 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
> 
> diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
> new file mode 100644
> index 000000000000..8fc6b4a63f06
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
> @@ -0,0 +1,119 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/display/rockchip/rockchip,dw-mipi-dsi2.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Rockchip specific extensions to the Synopsys Designware MIPI DSI2
> +
> +maintainers:
> +  - Heiko Stuebner <heiko@sntech.de>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - rockchip,rk3588-mipi-dsi2
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 2
> +
> +  clock-names:
> +    items:
> +      - const: pclk
> +      - const: sys
> +
> +  rockchip,grf:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      This SoC uses GRF regs to switch between vopl/vopb.
> +
> +  phys:
> +    maxItems: 1
> +
> +  phy-names:
> +    const: dcphy
> +
> +  ports:

Nodes after properties.

> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Input node to receive pixel data.
> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: DSI output node to panel.
> +
> +    required:
> +      - port@0
> +      - port@1
> +
> +  power-domains:
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  reset-names:
> +    const: apb
> +
> +required:
> +  - compatible
> +  - clocks
> +  - clock-names
> +  - rockchip,grf
> +  - phys
> +  - phy-names
> +  - ports
> +  - reg
> +
> +allOf:
> +  - $ref: ../dsi-controller.yaml#

Absolute path: /schemas/...

> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/rockchip,rk3588-cru.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/power/rk3588-power.h>
> +    #include <dt-bindings/reset/rockchip,rk3588-cru.h>
> +
> +    soc {
> +      #address-cells = <2>;
> +      #size-cells = <2>;
> +
> +      dsi0: dsi@fde20000 {

Drop unused labels.

> +        compatible = "rockchip,rk3588-mipi-dsi2";
> +        reg = <0x0 0xfde20000 0x0 0x10000>;
> +        interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH 0>;
> +        clocks = <&cru PCLK_DSIHOST0>, <&cru CLK_DSIHOST0>;
> +        clock-names = "pclk", "sys";
> +        resets = <&cru SRST_P_DSIHOST0>;
> +        reset-names = "apb";
> +        power-domains = <&power RK3588_PD_VOP>;
> +        phys = <&mipidcphy0>;
> +        phy-names = "dcphy";
> +        rockchip,grf = <&vop_grf>;
> +
> +        ports {
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +          dsi0_in: port@0 {
> +            reg = <0>;
> +          };
> +
> +          dsi0_out: port@1 {
> +            reg = <1>;
> +          };
> +        };
> +      };
> +    };
> -- 
> 2.45.2
> 

Re: [PATCH 0/3] drm/rockchip: Add driver for the new DSI2 controller

[Daniel Semkowicz]

Hello Heiko,

> This series adds a bridge and glue driver for the DSI2 controller found
> in the rk3588 soc from Rockchip, that is based on a Synopsis IP block.
> 
> As the manual states:
> The Display Serial Interface 2 (DSI-2) is part of a group of communication
> protocols defined by the MIPI Alliance. The MIPI DSI-2 Host Controller is
> a digital core that implements all protocol functions defined in the
> MIPI DSI-2 Specification.
> 
> 
> While the driver structure is very similar to the previous DSI controller,
> the programming model of the core is quite different, with a completely
> new register set.
> 
> Another notable difference is that the phy interface is variable now too
> in its width and some other settings.
> 
> 
> Heiko Stuebner (3):
>   drm/bridge/synopsys: Add MIPI DSI2 host controller bridge
>   dt-bindings: display: rockchip: Add schema for RK3588 DW DSI2
>     controller
>   drm/rockchip: Add MIPI DSI2 glue driver for RK3588
> 
>  .../rockchip/rockchip,rk3588-mipi-dsi2.yaml   |  119 ++
>  drivers/gpu/drm/bridge/synopsys/Kconfig       |    6 +
>  drivers/gpu/drm/bridge/synopsys/Makefile      |    1 +
>  .../gpu/drm/bridge/synopsys/dw-mipi-dsi2.c    | 1034 +++++++++++++++++
>  drivers/gpu/drm/rockchip/Kconfig              |   10 +
>  drivers/gpu/drm/rockchip/Makefile             |    1 +
>  .../gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c  |  524 +++++++++
>  drivers/gpu/drm/rockchip/rockchip_drm_drv.c   |    2 +
>  drivers/gpu/drm/rockchip/rockchip_drm_drv.h   |    1 +
>  include/drm/bridge/dw_mipi_dsi2.h             |   94 ++
>  10 files changed, 1792 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/rockchip/rockchip,rk3588-mipi-dsi2.yaml
>  create mode 100644 drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c
>  create mode 100644 drivers/gpu/drm/rockchip/dw-mipi-dsi2-rockchip.c
>  create mode 100644 include/drm/bridge/dw_mipi_dsi2.h
> 
> -- 
> 2.45.2

Thank you for this work!

Sucessfuly tested this series with DSI/LVDS bridge.

Test configuration was described in the thread "[PATCH v3 0/2] MIPI DSI
phy for rk3588":
https://lore.kernel.org/all/20241120093702.9018-1-dse@thaumatec.com/

Tested-by: Daniel Semkowicz <dse@thaumatec.com>

Kind regards
Daniel

Re: [PATCH 3/3] drm/rockchip: Add MIPI DSI2 glue driver for RK3588

[Heiko Stübner]

Hi,

Am Mittwoch, 6. November 2024, 14:33:25 CET schrieb Diederik de Haas:
> > +#define IPI_DEPTH_5_6_5_BITS		0x02
> > +#define IPI_DEPTH_6_BITS		0x03
> > +#define IPI_DEPTH_8_BITS		0x05
> > +#define IPI_DEPTH_10_BITS		0x06
> 
> Possibly dumb remark (sorry):
> drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi2.c also defines these
> values, so wouldn't it be better if they're defined in 1 place?

they are quite device-specific, so for me it doesn't really make sense
to try to centralize them. I.e. these are the values that need to go into
the GRF register to select a specific depth and are more or less the
same by chance.

I still remember quite well the answer to why Rockchip hardware engineers
sometimes shuffle around similar grf entries between socs "because they
want to" ;-)

At least for the rk3576, they seem to stay the same for now, though part
of me just expects the values to change in the future.

So personally I'd like to keep them where they are :-)

Heiko

Re: [PATCH 1/3] drm/bridge/synopsys: Add MIPI DSI2 host controller bridge

[Heiko Stübner]

Hi,

Am Mittwoch, 6. November 2024, 14:54:39 CET schrieb neil.armstrong@linaro.org:
> > +#define UPDATE(v, h, l)			(((v) << (l)) & GENMASK((h), (l)))
> 
> I'm not super fan of this macro, overall I thinkg you should switch to
> regmap and make use of regmap_update_bits and drop dsi2_write/read wrappers
> to readl/writel.

Yep you're right. That macro acutally is just FIELD_PREP in disguise ;-)
So I've gone with that (and regmap).


> <snip>
> 
> > +
> > +static struct dw_mipi_dsi2 *
> > +__dw_mipi_dsi2_probe(struct platform_device *pdev,
> > +		     const struct dw_mipi_dsi2_plat_data *plat_data)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct reset_control *apb_rst;
> > +	struct dw_mipi_dsi2 *dsi2;
> > +	int ret;
> > +
> > +	dsi2 = devm_kzalloc(dev, sizeof(*dsi2), GFP_KERNEL);
> > +	if (!dsi2)
> > +		return ERR_PTR(-ENOMEM);
> > +
> > +	dsi2->dev = dev;
> > +	dsi2->plat_data = plat_data;
> > +
> > +	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps ||
> > +	    !plat_data->phy_ops->get_timing)
> > +		return dev_err_ptr_probe(dev, -ENODEV, "Phy not properly configured\n");
> > +
> > +	if (!plat_data->base) {
> > +		dsi2->base = devm_platform_ioremap_resource(pdev, 0);
> > +		if (IS_ERR(dsi2->base))
> > +			return ERR_PTR(-ENODEV);
> > +	} else {
> > +		dsi2->base = plat_data->base;
> > +	}
> > +
> > +	dsi2->pclk = devm_clk_get(dev, "pclk");
> > +	if (IS_ERR(dsi2->pclk))
> > +		return dev_err_cast_probe(dev, dsi2->pclk, "Unable to get pclk\n");
> > +
> > +	dsi2->sys_clk = devm_clk_get(dev, "sys");
> > +	if (IS_ERR(dsi2->sys_clk))
> > +		return dev_err_cast_probe(dev, dsi2->sys_clk, "Unable to get sys_clk\n");
> > +
> > +	/*
> > +	 * Note that the reset was not defined in the initial device tree, so
> > +	 * we have to be prepared for it not being found.
> > +	 */
> > +	apb_rst = devm_reset_control_get_optional_exclusive(dev, "apb");
> > +	if (IS_ERR(apb_rst))
> > +		return dev_err_cast_probe(dev, apb_rst, "Unable to get reset control\n");
> > +
> > +	if (apb_rst) {
> > +		ret = clk_prepare_enable(dsi2->pclk);
> > +		if (ret) {
> > +			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
> > +			return ERR_PTR(ret);
> > +		}
> > +
> > +		reset_control_assert(apb_rst);
> > +		usleep_range(10, 20);
> > +		reset_control_deassert(apb_rst);
> > +
> > +		clk_disable_unprepare(dsi2->pclk);
> > +	}
> > +
> > +	pm_runtime_enable(dev);
> > +
> > +	dsi2->dsi_host.ops = &dw_mipi_dsi2_host_ops;
> > +	dsi2->dsi_host.dev = dev;
> > +	ret = mipi_dsi_host_register(&dsi2->dsi_host);
> > +	if (ret) {
> > +		dev_err(dev, "Failed to register MIPI host: %d\n", ret);
> > +		pm_runtime_disable(dev);
> > +		return ERR_PTR(ret);
> > +	}
> > +
> > +	dsi2->bridge.driver_private = dsi2;
> > +	dsi2->bridge.funcs = &dw_mipi_dsi2_bridge_funcs;
> > +	dsi2->bridge.of_node = pdev->dev.of_node;
> > +
> > +	return dsi2;
> > +}
> > +
> > +static void __dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
> > +{
> > +	mipi_dsi_host_unregister(&dsi2->dsi_host);
> > +
> > +	pm_runtime_disable(dsi2->dev);
> > +}
> > +
> > +/*
> > + * Probe/remove API, used from platforms based on the DRM bridge API.
> > + */
> > +struct dw_mipi_dsi2 *
> > +dw_mipi_dsi2_probe(struct platform_device *pdev,
> > +		   const struct dw_mipi_dsi2_plat_data *plat_data)
> > +{
> > +	return __dw_mipi_dsi2_probe(pdev, plat_data);
> > +}
> > +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_probe);
> > +
> > +void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2)
> > +{
> > +	__dw_mipi_dsi2_remove(dsi2);
> > +}
> > +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_remove);
> 
> Since it's not use yet, you should probably drop those since it's dead
> code.

Though it is used. The Rockchip glue in patch 3 calls 
	dsi2->dmd = dw_mipi_dsi2_probe(pdev, &dsi2->pdata);
in its dw_mipi_dsi2_rockchip_probe() and
	dw_mipi_dsi2_remove(dsi2->dmd);
in its dw_mipi_dsi2_rockchip_remove() for the whole bridge setup

Similarly the below bind/unbind functions are called for the bridge-attach
from the component part of the Rockchip glue.

Which is the same way the dsi1 driver handles things right now.


> > +
> > +/*
> > + * Bind/unbind API, used from platforms based on the component framework.
> > + */
> > +int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder)
> > +{
> > +	return drm_bridge_attach(encoder, &dsi2->bridge, NULL, 0);
> > +}
> > +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_bind);
> > +
> > +void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2)
> > +{
> > +}
> > +EXPORT_SYMBOL_GPL(dw_mipi_dsi2_unbind);

[...]

> > +struct dw_mipi_dsi2 *dw_mipi_dsi2_probe(struct platform_device *pdev,
> > +					const struct dw_mipi_dsi2_plat_data *plat_data);
> > +void dw_mipi_dsi2_remove(struct dw_mipi_dsi2 *dsi2);
> > +int dw_mipi_dsi2_bind(struct dw_mipi_dsi2 *dsi2, struct drm_encoder *encoder);
> > +void dw_mipi_dsi2_unbind(struct dw_mipi_dsi2 *dsi2);
> > +
> > +#endif /* __DW_MIPI_DSI2__ */
> 
> Overall the driver is very close to dw-mipi-dsi, si it's overall good!

that was the intention ... so that I don't introduce issues that were
already solved elsewhere ;-) .

Heiko