[PATCH v2 0/4] {am62,am62a}-phycore-som: Add R5F and C7xv device nodes

[PATCH v2 0/4] {am62,am62a}-phycore-som: Add R5F and C7xv device nodes

[Daniel Schultz]

This patch series is based on [1] and adds these R5F and C7xv device nodes
to the am62- and am62a-phycore-som device-trees. It also reserves main_timer2
as well as main_rti4 for the C7 DSP firmware.

1: https://lore.kernel.org/linux-arm-kernel/20250502220325.3230653-1-jm@ti.com/T/#t

Changes in v2:
  * Rebased to latest master branch.

Daniel Schultz (4):
  arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors
  arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors
  arm64: dts: ti: k3-am62a-phycore-som: Reserve main_rti4 for C7x DSP
  arm64: dts: ti: k3-am62a-phycore-som: Reserve main_timer2 for C7x DSP

 .../boot/dts/ti/k3-am62-phycore-som.dtsi      |  35 +++++-
 .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 106 +++++++++++++++++-
 2 files changed, 129 insertions(+), 12 deletions(-)

-- 
2.25.1

[PATCH v2 1/4] arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors

[Daniel Schultz]

For every remote processor, set up dedicated memory regions and
associate the required mailbox channels. Allocate two memory areas
per remote core: one 1MB region for vring shared buffers, and
another for external memory used by the remote processor for its
resource table and trace buffer.

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
---
 .../boot/dts/ti/k3-am62-phycore-som.dtsi      | 35 +++++++++++++++----
 1 file changed, 29 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
index 55ed418c023b..3075979935d5 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
@@ -64,6 +64,18 @@ mcu_m4fss_memory_region: m4f-memory@9cc00000 {
 			no-map;
 		};
 
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9da00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9da00000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+
 		secure_tfa_ddr: tfa@9e780000 {
 			reg = <0x00 0x9e780000 0x00 0x80000>;
 			alignment = <0x1000>;
@@ -75,12 +87,6 @@ secure_ddr: optee@9e800000 {
 			alignment = <0x1000>;
 			no-map;
 		};
-
-		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9db00000 0x00 0x00c00000>;
-			no-map;
-		};
 	};
 
 	vcc_5v0_som: regulator-vcc-5v0-som {
@@ -240,10 +246,17 @@ cpsw3g_phy1: ethernet-phy@1 {
 };
 
 &mailbox0_cluster0 {
+	status = "okay";
+
 	mbox_m4_0: mbox-m4-0 {
 		ti,mbox-rx = <0 0 0>;
 		ti,mbox-tx = <1 0 0>;
 	};
+
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
 };
 
 &main_pktdma {
@@ -386,3 +399,13 @@ &sdhci0 {
 	bootph-all;
 	status = "okay";
 };
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+			<&wkup_r5fss0_core0_memory_region>;
+};
-- 
2.25.1

Re: [PATCH v2 1/4] arm64: dts: ti: k3-am62-phycore-som: Enable Co-processors

[Wadim Egorov]

Am 06.05.25 um 16:36 schrieb Daniel Schultz:
> For every remote processor, set up dedicated memory regions and
> associate the required mailbox channels. Allocate two memory areas
> per remote core: one 1MB region for vring shared buffers, and
> another for external memory used by the remote processor for its
> resource table and trace buffer.
> 
> Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>

> ---
>   .../boot/dts/ti/k3-am62-phycore-som.dtsi      | 35 +++++++++++++++----
>   1 file changed, 29 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> index 55ed418c023b..3075979935d5 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi
> @@ -64,6 +64,18 @@ mcu_m4fss_memory_region: m4f-memory@9cc00000 {
>   			no-map;
>   		};
>   
> +		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9da00000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9da00000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		wkup_r5fss0_core0_memory_region: r5f-memory@9db00000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9db00000 0x00 0xc00000>;
> +			no-map;
> +		};
> +
>   		secure_tfa_ddr: tfa@9e780000 {
>   			reg = <0x00 0x9e780000 0x00 0x80000>;
>   			alignment = <0x1000>;
> @@ -75,12 +87,6 @@ secure_ddr: optee@9e800000 {
>   			alignment = <0x1000>;
>   			no-map;
>   		};
> -
> -		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
> -			compatible = "shared-dma-pool";
> -			reg = <0x00 0x9db00000 0x00 0x00c00000>;
> -			no-map;
> -		};
>   	};
>   
>   	vcc_5v0_som: regulator-vcc-5v0-som {
> @@ -240,10 +246,17 @@ cpsw3g_phy1: ethernet-phy@1 {
>   };
>   
>   &mailbox0_cluster0 {
> +	status = "okay";
> +
>   	mbox_m4_0: mbox-m4-0 {
>   		ti,mbox-rx = <0 0 0>;
>   		ti,mbox-tx = <1 0 0>;
>   	};
> +
> +	mbox_r5_0: mbox-r5-0 {
> +		ti,mbox-rx = <2 0 0>;
> +		ti,mbox-tx = <3 0 0>;
> +	};
>   };
>   
>   &main_pktdma {
> @@ -386,3 +399,13 @@ &sdhci0 {
>   	bootph-all;
>   	status = "okay";
>   };
> +
> +&wkup_r5fss0 {
> +	status = "okay";
> +};
> +
> +&wkup_r5fss0_core0 {
> +	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
> +	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
> +			<&wkup_r5fss0_core0_memory_region>;
> +};

[PATCH v2 2/4] arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

[Daniel Schultz]

For every remote processor, set up dedicated memory regions and
associate the required mailbox channels. Allocate two memory areas
per remote core: one 1MB region for vring shared buffers, and
another for external memory used by the remote processor for its
resource table and trace buffer.

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
---
 .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
 1 file changed, 90 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
index 147d56b87984..049aa358e796 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
@@ -59,6 +59,42 @@ linux,cma {
 			linux,cma-default;
 		};
 
+		c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99800000 0x00 0x100000>;
+			no-map;
+		};
+
+		c7x_0_memory_region: c7x-memory@99900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x99900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b800000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9b900000 0x00 0xf00000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c800000 0x00 0x100000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c900000 0x00 0xf00000>;
+			no-map;
+		};
+
 		secure_tfa_ddr: tfa@9e780000 {
 			reg = <0x00 0x9e780000 0x00 0x80000>;
 			alignment = <0x1000>;
@@ -70,12 +106,6 @@ secure_ddr: optee@9e800000 {
 			alignment = <0x1000>;
 			no-map;
 		};
-
-		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
-			compatible = "shared-dma-pool";
-			reg = <0x00 0x9c900000 0x00 0x01e00000>;
-			no-map;
-		};
 	};
 
 	vcc_5v0_som: regulator-vcc-5v0-som {
@@ -170,6 +200,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) EXTINTn */
 	};
 };
 
+&c7x_0 {
+	mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
+	memory-region = <&c7x_0_dma_memory_region>,
+			<&c7x_0_memory_region>;
+	status = "okay";
+};
+
 &cpsw3g {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_rgmii1_pins_default>;
@@ -200,6 +237,33 @@ &fss {
 	status = "okay";
 };
 
+&mailbox0_cluster0 {
+	status = "okay";
+
+	mbox_r5_0: mbox-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster1 {
+	status = "okay";
+
+	mbox_c7x_0: mbox-c7x-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster2 {
+	status = "okay";
+
+	mbox_mcu_r5_0: mbox-mcu-r5-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
 &main_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_pins_default>;
@@ -315,6 +379,16 @@ &main_pktdma {
 	bootph-all;
 };
 
+&mcu_r5fss0 {
+	status = "okay";
+};
+
+&mcu_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+};
+
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
@@ -343,3 +417,13 @@ &sdhci0 {
 	bootph-all;
 	status = "okay";
 };
+
+&wkup_r5fss0 {
+	status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
+	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+			<&wkup_r5fss0_core0_memory_region>;
+};
-- 
2.25.1

Re: [PATCH v2 2/4] arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

[Andrew Davis]

On 5/6/25 8:36 AM, Daniel Schultz wrote:
> For every remote processor, set up dedicated memory regions and
> associate the required mailbox channels. Allocate two memory areas
> per remote core: one 1MB region for vring shared buffers, and
> another for external memory used by the remote processor for its
> resource table and trace buffer.
> 
> Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
> ---
>   .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
>   1 file changed, 90 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> index 147d56b87984..049aa358e796 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> @@ -59,6 +59,42 @@ linux,cma {
>   			linux,cma-default;
>   		};
>   
> +		c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x99800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		c7x_0_memory_region: c7x-memory@99900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x99900000 0x00 0xf00000>;
> +			no-map;
> +		};
> +
> +		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9b800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9b900000 0x00 0xf00000>;
> +			no-map;
> +		};
> +
> +		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9c800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9c900000 0x00 0xf00000>;
> +			no-map;
> +		};
> +
>   		secure_tfa_ddr: tfa@9e780000 {
>   			reg = <0x00 0x9e780000 0x00 0x80000>;
>   			alignment = <0x1000>;
> @@ -70,12 +106,6 @@ secure_ddr: optee@9e800000 {
>   			alignment = <0x1000>;
>   			no-map;
>   		};
> -
> -		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
> -			compatible = "shared-dma-pool";
> -			reg = <0x00 0x9c900000 0x00 0x01e00000>;
> -			no-map;
> -		};
>   	};
>   
>   	vcc_5v0_som: regulator-vcc-5v0-som {
> @@ -170,6 +200,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) EXTINTn */
>   	};
>   };
>   
> +&c7x_0 {
> +	mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
> +	memory-region = <&c7x_0_dma_memory_region>,
> +			<&c7x_0_memory_region>;
> +	status = "okay";
> +};
> +
>   &cpsw3g {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_rgmii1_pins_default>;
> @@ -200,6 +237,33 @@ &fss {
>   	status = "okay";
>   };
>   
> +&mailbox0_cluster0 {
> +	status = "okay";
> +
> +	mbox_r5_0: mbox-r5-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
> +&mailbox0_cluster1 {
> +	status = "okay";
> +
> +	mbox_c7x_0: mbox-c7x-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
> +&mailbox0_cluster2 {
> +	status = "okay";
> +
> +	mbox_mcu_r5_0: mbox-mcu-r5-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
>   &main_i2c0 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_i2c0_pins_default>;
> @@ -315,6 +379,16 @@ &main_pktdma {
>   	bootph-all;
>   };
>   
> +&mcu_r5fss0 {
> +	status = "okay";
> +};
> +
> +&mcu_r5fss0_core0 {
> +	mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;

These mboxes items should be combined as they are both part of a single
two-element item, not a big deal for now as the output DTB is the same,

Reviewed-by: Andrew Davis <afd@ti.com>

> +	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> +			<&mcu_r5fss0_core0_memory_region>;
> +};
> +
>   &ospi0 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&ospi0_pins_default>;
> @@ -343,3 +417,13 @@ &sdhci0 {
>   	bootph-all;
>   	status = "okay";
>   };
> +
> +&wkup_r5fss0 {
> +	status = "okay";
> +};
> +
> +&wkup_r5fss0_core0 {
> +	mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
> +	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
> +			<&wkup_r5fss0_core0_memory_region>;
> +};

Re: [PATCH v2 2/4] arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

[Daniel Schultz]

On 5/6/25 16:20, Andrew Davis wrote:
> On 5/6/25 8:36 AM, Daniel Schultz wrote:
>> For every remote processor, set up dedicated memory regions and
>> associate the required mailbox channels. Allocate two memory areas
>> per remote core: one 1MB region for vring shared buffers, and
>> another for external memory used by the remote processor for its
>> resource table and trace buffer.
>>
>> Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
>> ---
>>   .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
>>   1 file changed, 90 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi 
>> b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> index 147d56b87984..049aa358e796 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> @@ -59,6 +59,42 @@ linux,cma {
>>               linux,cma-default;
>>           };
>>   +        c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x99800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        c7x_0_memory_region: c7x-memory@99900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x99900000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9b800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9b900000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9c800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9c900000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>>           secure_tfa_ddr: tfa@9e780000 {
>>               reg = <0x00 0x9e780000 0x00 0x80000>;
>>               alignment = <0x1000>;
>> @@ -70,12 +106,6 @@ secure_ddr: optee@9e800000 {
>>               alignment = <0x1000>;
>>               no-map;
>>           };
>> -
>> -        wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
>> -            compatible = "shared-dma-pool";
>> -            reg = <0x00 0x9c900000 0x00 0x01e00000>;
>> -            no-map;
>> -        };
>>       };
>>         vcc_5v0_som: regulator-vcc-5v0-som {
>> @@ -170,6 +200,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) 
>> EXTINTn */
>>       };
>>   };
>>   +&c7x_0 {
>> +    mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
>> +    memory-region = <&c7x_0_dma_memory_region>,
>> +            <&c7x_0_memory_region>;
>> +    status = "okay";
>> +};
>> +
>>   &cpsw3g {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&main_rgmii1_pins_default>;
>> @@ -200,6 +237,33 @@ &fss {
>>       status = "okay";
>>   };
>>   +&mailbox0_cluster0 {
>> +    status = "okay";
>> +
>> +    mbox_r5_0: mbox-r5-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>> +&mailbox0_cluster1 {
>> +    status = "okay";
>> +
>> +    mbox_c7x_0: mbox-c7x-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>> +&mailbox0_cluster2 {
>> +    status = "okay";
>> +
>> +    mbox_mcu_r5_0: mbox-mcu-r5-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>>   &main_i2c0 {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&main_i2c0_pins_default>;
>> @@ -315,6 +379,16 @@ &main_pktdma {
>>       bootph-all;
>>   };
>>   +&mcu_r5fss0 {
>> +    status = "okay";
>> +};
>> +
>> +&mcu_r5fss0_core0 {
>> +    mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;
>
> These mboxes items should be combined as they are both part of a single
> two-element item, not a big deal for now as the output DTB is the same,

Yes, I can do that. Heads up this is copied from the recent k3-am62a7-sk 
update. You might wanna consider updating this board too.

- Daniel

>
> Reviewed-by: Andrew Davis <afd@ti.com>
>
>> +    memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
>> +            <&mcu_r5fss0_core0_memory_region>;
>> +};
>> +
>>   &ospi0 {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&ospi0_pins_default>;
>> @@ -343,3 +417,13 @@ &sdhci0 {
>>       bootph-all;
>>       status = "okay";
>>   };
>> +
>> +&wkup_r5fss0 {
>> +    status = "okay";
>> +};
>> +
>> +&wkup_r5fss0_core0 {
>> +    mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
>> +    memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
>> +            <&wkup_r5fss0_core0_memory_region>;
>> +};

Re: [PATCH v2 2/4] arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

[Wadim Egorov]

Am 06.05.25 um 16:36 schrieb Daniel Schultz:
> For every remote processor, set up dedicated memory regions and
> associate the required mailbox channels. Allocate two memory areas
> per remote core: one 1MB region for vring shared buffers, and
> another for external memory used by the remote processor for its
> resource table and trace buffer.
> 
> Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
> ---
>   .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
>   1 file changed, 90 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> index 147d56b87984..049aa358e796 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
> @@ -59,6 +59,42 @@ linux,cma {
>   			linux,cma-default;
>   		};
>   
> +		c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x99800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		c7x_0_memory_region: c7x-memory@99900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x99900000 0x00 0xf00000>;

Just checked the origin of this for the am62a7-sk, which is 
https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/commit/?h=10.01.10&id=a82cef91b301e3a03a4efe0f49e6cb8cf50f43af

The size for the c7x-memory is 0x01f00000 and not 0xf00000

> +			no-map;
> +		};
> +
> +		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {

which is relevant because your next reserved memory area starts at 
0x9b800000 (would be fine with a size of 0x1f00000). If you really want 
to have a size of 0xf00000, your next block should start at 9A800000.

Can you please double check and use the free memory inbetween if 
0xf00000 is correct.

> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9b800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9b900000 0x00 0xf00000>;
> +			no-map;
> +		};
> +
> +		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9c800000 0x00 0x100000>;
> +			no-map;
> +		};
> +
> +		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
> +			compatible = "shared-dma-pool";
> +			reg = <0x00 0x9c900000 0x00 0xf00000>;
> +			no-map;
> +		};
> +
>   		secure_tfa_ddr: tfa@9e780000 {
>   			reg = <0x00 0x9e780000 0x00 0x80000>;
>   			alignment = <0x1000>;
> @@ -70,12 +106,6 @@ secure_ddr: optee@9e800000 {
>   			alignment = <0x1000>;
>   			no-map;
>   		};
> -
> -		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
> -			compatible = "shared-dma-pool";
> -			reg = <0x00 0x9c900000 0x00 0x01e00000>;
> -			no-map;
> -		};
>   	};
>   
>   	vcc_5v0_som: regulator-vcc-5v0-som {
> @@ -170,6 +200,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) EXTINTn */
>   	};
>   };
>   
> +&c7x_0 {
> +	mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
> +	memory-region = <&c7x_0_dma_memory_region>,
> +			<&c7x_0_memory_region>;
> +	status = "okay";
> +};
> +
>   &cpsw3g {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_rgmii1_pins_default>;
> @@ -200,6 +237,33 @@ &fss {
>   	status = "okay";
>   };
>   
> +&mailbox0_cluster0 {
> +	status = "okay";
> +
> +	mbox_r5_0: mbox-r5-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
> +&mailbox0_cluster1 {
> +	status = "okay";
> +
> +	mbox_c7x_0: mbox-c7x-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
> +&mailbox0_cluster2 {
> +	status = "okay";
> +
> +	mbox_mcu_r5_0: mbox-mcu-r5-0 {
> +		ti,mbox-rx = <0 0 0>;
> +		ti,mbox-tx = <1 0 0>;
> +	};
> +};
> +
>   &main_i2c0 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&main_i2c0_pins_default>;
> @@ -315,6 +379,16 @@ &main_pktdma {
>   	bootph-all;
>   };
>   
> +&mcu_r5fss0 {
> +	status = "okay";
> +};
> +
> +&mcu_r5fss0_core0 {
> +	mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;
> +	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
> +			<&mcu_r5fss0_core0_memory_region>;
> +};
> +
>   &ospi0 {
>   	pinctrl-names = "default";
>   	pinctrl-0 = <&ospi0_pins_default>;
> @@ -343,3 +417,13 @@ &sdhci0 {
>   	bootph-all;
>   	status = "okay";
>   };
> +
> +&wkup_r5fss0 {
> +	status = "okay";
> +};
> +
> +&wkup_r5fss0_core0 {
> +	mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
> +	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
> +			<&wkup_r5fss0_core0_memory_region>;
> +};

Re: [PATCH v2 2/4] arm64: dts: ti: k3-am62a-phycore-som: Enable Co-processors

[Daniel Schultz]

On 5/6/25 17:41, Wadim Egorov wrote:
> Am 06.05.25 um 16:36 schrieb Daniel Schultz:
>> For every remote processor, set up dedicated memory regions and
>> associate the required mailbox channels. Allocate two memory areas
>> per remote core: one 1MB region for vring shared buffers, and
>> another for external memory used by the remote processor for its
>> resource table and trace buffer.
>>
>> Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
>> ---
>>   .../boot/dts/ti/k3-am62a-phycore-som.dtsi     | 96 +++++++++++++++++--
>>   1 file changed, 90 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi 
>> b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> index 147d56b87984..049aa358e796 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
>> @@ -59,6 +59,42 @@ linux,cma {
>>               linux,cma-default;
>>           };
>>   +        c7x_0_dma_memory_region: c7x-dma-memory@99800000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x99800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        c7x_0_memory_region: c7x-memory@99900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x99900000 0x00 0xf00000>;
>
> Just checked the origin of this for the am62a7-sk, which is 
> https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/commit/?h=10.01.10&id=a82cef91b301e3a03a4efe0f49e6cb8cf50f43af
>
> The size for the c7x-memory is 0x01f00000 and not 0xf00000
>
>> +            no-map;
>> +        };
>> +
>> +        mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@9b800000 {
>
> which is relevant because your next reserved memory area starts at 
> 0x9b800000 (would be fine with a size of 0x1f00000). If you really 
> want to have a size of 0xf00000, your next block should start at 
> 9A800000.
>
> Can you please double check and use the free memory inbetween if 
> 0xf00000 is correct.

Hi Wadim,

I copied all those nodes from the k3-am62a7-sk board update which just 
got merged [1]. I don't want to change that now because I'm afraid the 
default TI mcu firmware won't work with different addresses anymore.

@Andrew: FYI there is a gap now in reserved memory but I assume you're 
already aware.

- Daniel

1: 
https://lore.kernel.org/linux-arm-kernel/174653697389.718892.12387672790395559537.b4-ty@ti.com/T/#m7f099b9507759c8f56733004222ed1b1bbdd0736

>
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9b800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        mcu_r5fss0_core0_memory_region: r5f-dma-memory@9b900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9b900000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9c800000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0x9c900000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>>           secure_tfa_ddr: tfa@9e780000 {
>>               reg = <0x00 0x9e780000 0x00 0x80000>;
>>               alignment = <0x1000>;
>> @@ -70,12 +106,6 @@ secure_ddr: optee@9e800000 {
>>               alignment = <0x1000>;
>>               no-map;
>>           };
>> -
>> -        wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
>> -            compatible = "shared-dma-pool";
>> -            reg = <0x00 0x9c900000 0x00 0x01e00000>;
>> -            no-map;
>> -        };
>>       };
>>         vcc_5v0_som: regulator-vcc-5v0-som {
>> @@ -170,6 +200,13 @@ AM62AX_IOPAD(0x1f4, PIN_INPUT, 0) /* (D16) 
>> EXTINTn */
>>       };
>>   };
>>   +&c7x_0 {
>> +    mboxes = <&mailbox0_cluster1>, <&mbox_c7x_0>;
>> +    memory-region = <&c7x_0_dma_memory_region>,
>> +            <&c7x_0_memory_region>;
>> +    status = "okay";
>> +};
>> +
>>   &cpsw3g {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&main_rgmii1_pins_default>;
>> @@ -200,6 +237,33 @@ &fss {
>>       status = "okay";
>>   };
>>   +&mailbox0_cluster0 {
>> +    status = "okay";
>> +
>> +    mbox_r5_0: mbox-r5-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>> +&mailbox0_cluster1 {
>> +    status = "okay";
>> +
>> +    mbox_c7x_0: mbox-c7x-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>> +&mailbox0_cluster2 {
>> +    status = "okay";
>> +
>> +    mbox_mcu_r5_0: mbox-mcu-r5-0 {
>> +        ti,mbox-rx = <0 0 0>;
>> +        ti,mbox-tx = <1 0 0>;
>> +    };
>> +};
>> +
>>   &main_i2c0 {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&main_i2c0_pins_default>;
>> @@ -315,6 +379,16 @@ &main_pktdma {
>>       bootph-all;
>>   };
>>   +&mcu_r5fss0 {
>> +    status = "okay";
>> +};
>> +
>> +&mcu_r5fss0_core0 {
>> +    mboxes = <&mailbox0_cluster2>, <&mbox_mcu_r5_0>;
>> +    memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
>> +            <&mcu_r5fss0_core0_memory_region>;
>> +};
>> +
>>   &ospi0 {
>>       pinctrl-names = "default";
>>       pinctrl-0 = <&ospi0_pins_default>;
>> @@ -343,3 +417,13 @@ &sdhci0 {
>>       bootph-all;
>>       status = "okay";
>>   };
>> +
>> +&wkup_r5fss0 {
>> +    status = "okay";
>> +};
>> +
>> +&wkup_r5fss0_core0 {
>> +    mboxes = <&mailbox0_cluster0>, <&mbox_r5_0>;
>> +    memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
>> +            <&wkup_r5fss0_core0_memory_region>;
>> +};
>

[PATCH v2 3/4] arm64: dts: ti: k3-am62a-phycore-som: Reserve main_rti4 for C7x DSP

[Daniel Schultz]

The main rti4 watchdog timer is used by the C7x DSP, so reserve the
timer in the linux device tree.

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
---
 arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
index 049aa358e796..7fa0060af4e8 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
@@ -379,6 +379,11 @@ &main_pktdma {
 	bootph-all;
 };
 
+/* main_rti4 is used by C7x DSP */
+&main_rti4 {
+	status = "reserved";
+};
+
 &mcu_r5fss0 {
 	status = "okay";
 };
-- 
2.25.1

[PATCH v2 4/4] arm64: dts: ti: k3-am62a-phycore-som: Reserve main_timer2 for C7x DSP

[Daniel Schultz]

C7x DSP uses main_timer2, so mark it as reserved in linux DT.

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
---
 arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
index 7fa0060af4e8..14f7840ccf2f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-phycore-som.dtsi
@@ -384,6 +384,11 @@ &main_rti4 {
 	status = "reserved";
 };
 
+/* main_timer2 is used by C7x DSP */
+&main_timer2 {
+	status = "reserved";
+};
+
 &mcu_r5fss0 {
 	status = "okay";
 };
-- 
2.25.1