linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: kishorek.kadiyala@gmail.com (kishore kadiyala)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 1/4] omap4 hsmmc: Adding card detect support for MMC1
Date: Mon, 27 Sep 2010 13:25:01 +0530	[thread overview]
Message-ID: <AANLkTi=YvtrfmUTc-YBAUjEXn1v3pPLmhb92J60AhU28@mail.gmail.com> (raw)
In-Reply-To: <9408.10.24.255.18.1285348400.squirrel@dbdmail.itg.ti.com>

Cc: Samuel Ortiz <sameo@linux.intel.com>

On Fri, Sep 24, 2010 at 10:43 PM, kishore kadiyala
<kishore.kadiyala@ti.com> wrote:
> Adding card detect callback function and card detect configuration
> function for MMC1 Controller on OMAP4.
>
> Card detect configuration function does initial configuration of the
> MMC Control & PullUp-PullDown registers of Phoenix.
>
> For MMC1 Controller, card detect interrupt source is
> twl6030 which is non-gpio. The card detect call back function provides
> card present/absent status by reading MMC Control register present
> on twl6030.
>
> Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
> the suspend/resume initialization which was done in omap_hsmmc_gpio_init
> previously is moved to the probe thus making it generic for both OMAP3 & OMAP4.
>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
> Cc: Adrian Hunter <adrian.hunter@nokia.com>
> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
> ---
> ?arch/arm/mach-omap2/board-4430sdp.c | ? ?7 +++-
> ?drivers/mfd/twl6030-irq.c ? ? ? ? ? | ? 73 +++++++++++++++++++++++++++++++++++
> ?drivers/mmc/host/omap_hsmmc.c ? ? ? | ? ?4 +-
> ?include/linux/i2c/twl.h ? ? ? ? ? ? | ? 31 +++++++++++++++
> ?4 files changed, 112 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
> index 9447644..a49f285 100644
> --- a/arch/arm/mach-omap2/board-4430sdp.c
> +++ b/arch/arm/mach-omap2/board-4430sdp.c
> @@ -227,9 +227,14 @@ static int omap4_twl6030_hsmmc_late_init(struct device *dev)
> ? ? ? ?struct omap_mmc_platform_data *pdata = dev->platform_data;
>
> ? ? ? ?/* Setting MMC1 Card detect Irq */
> - ? ? ? if (pdev->id == 0)
> + ? ? ? if (pdev->id == 0) {
> + ? ? ? ? ? ? ? ret = twl6030_mmc_card_detect_config();
> + ? ? ? ? ? ? ? if (ret)
> + ? ? ? ? ? ? ? ? ? ? ? pr_err("Failed configuring MMC1 card detect\n");
> ? ? ? ? ? ? ? ?pdata->slots[0].card_detect_irq = TWL6030_IRQ_BASE +
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?MMCDETECT_INTR_OFFSET;
> + ? ? ? ? ? ? ? pdata->slots[0].card_detect = twl6030_mmc_card_detect;
> + ? ? ? }
> ? ? ? ?return ret;
> ?}
>
> diff --git a/drivers/mfd/twl6030-irq.c b/drivers/mfd/twl6030-irq.c
> index 10bf228..2d3bb82 100644
> --- a/drivers/mfd/twl6030-irq.c
> +++ b/drivers/mfd/twl6030-irq.c
> @@ -36,6 +36,7 @@
> ?#include <linux/irq.h>
> ?#include <linux/kthread.h>
> ?#include <linux/i2c/twl.h>
> +#include <linux/platform_device.h>
>
> ?/*
> ?* TWL6030 (unlike its predecessors, which had two level interrupt handling)
> @@ -223,6 +224,78 @@ int twl6030_interrupt_mask(u8 bit_mask, u8 offset)
> ?}
> ?EXPORT_SYMBOL(twl6030_interrupt_mask);
>
> +int twl6030_mmc_card_detect_config(void)
> +{
> + ? ? ? int ret;
> + ? ? ? u8 reg_val = 0;
> +
> + ? ? ? /* Unmasking the Card detect Interrupt line for MMC1 from Phoenix */
> + ? ? ? twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? REG_INT_MSK_LINE_B);
> + ? ? ? twl6030_interrupt_unmask(TWL6030_MMCDETECT_INT_MASK,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? REG_INT_MSK_STS_B);
> + ? ? ? /*
> + ? ? ? ?* Intially Configuring MMC_CTRL for receving interrupts &
> + ? ? ? ?* Card status on TWL6030 for MMC1
> + ? ? ? ?*/
> + ? ? ? ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &reg_val, TWL6030_MMCCTRL);
> + ? ? ? if (ret < 0) {
> + ? ? ? ? ? ? ? pr_err("twl6030: Failed to read MMCCTRL, error %d\n", ret);
> + ? ? ? ? ? ? ? return ret;
> + ? ? ? }
> + ? ? ? reg_val &= ~VMMC_AUTO_OFF;
> + ? ? ? reg_val |= SW_FC;
> + ? ? ? ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val, TWL6030_MMCCTRL);
> + ? ? ? if (ret < 0) {
> + ? ? ? ? ? ? ? pr_err("twl6030: Failed to write MMCCTRL, error %d\n", ret);
> + ? ? ? ? ? ? ? return ret;
> + ? ? ? }
> +
> + ? ? ? /* Configuring PullUp-PullDown register */
> + ? ? ? ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &reg_val,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? TWL6030_CFG_INPUT_PUPD3);
> + ? ? ? if (ret < 0) {
> + ? ? ? ? ? ? ? pr_err("twl6030: Failed to read CFG_INPUT_PUPD3, error %d\n",
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret);
> + ? ? ? ? ? ? ? return ret;
> + ? ? ? }
> + ? ? ? reg_val &= ~(MMC_PU | MMC_PD);
> + ? ? ? ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? TWL6030_CFG_INPUT_PUPD3);
> + ? ? ? if (ret < 0) {
> + ? ? ? ? ? ? ? pr_err("twl6030: Failed to write CFG_INPUT_PUPD3, error %d\n",
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ret);
> + ? ? ? ? ? ? ? return ret;
> + ? ? ? }
> + ? ? ? return 0;
> +}
> +EXPORT_SYMBOL(twl6030_mmc_card_detect_config);
> +
> +int twl6030_mmc_card_detect(struct device *dev, int slot)
> +{
> + ? ? ? int ret = -EIO;
> + ? ? ? u8 read_reg = 0;
> + ? ? ? struct platform_device *pdev = to_platform_device(dev);
> +
> + ? ? ? if (pdev->id) {
> + ? ? ? ? ? ? ? /* TWL6030 provide's Card detect support for
> + ? ? ? ? ? ? ? ?* only MMC1 controller.
> + ? ? ? ? ? ? ? ?*/
> + ? ? ? ? ? ? ? pr_err("Unkown MMC controller %d in %s\n", pdev->id, __func__);
> + ? ? ? ? ? ? ? return ret;
> + ? ? ? }
> + ? ? ? /*
> + ? ? ? ?* BIT0 of MMC_CTRL on TWL6030 provides card status for MMC1
> + ? ? ? ?* 0 - Card not present ,1 - Card present
> + ? ? ? ?*/
> + ? ? ? ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, &read_reg,
> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? TWL6030_MMCCTRL);
> + ? ? ? if (ret >= 0)
> + ? ? ? ? ? ? ? ret = read_reg & STS_MMC;
> + ? ? ? return ret;
> +}
> +EXPORT_SYMBOL(twl6030_mmc_card_detect);
> +
> ?int twl6030_init_irq(int irq_num, unsigned irq_base, unsigned irq_end)
> ?{
>
> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
> index 562dbbb..a51894d 100644
> --- a/drivers/mmc/host/omap_hsmmc.c
> +++ b/drivers/mmc/host/omap_hsmmc.c
> @@ -466,8 +466,6 @@ static int omap_hsmmc_gpio_init(struct omap_mmc_platform_data *pdata)
> ? ? ? ?int ret;
>
> ? ? ? ?if (gpio_is_valid(pdata->slots[0].switch_pin)) {
> - ? ? ? ? ? ? ? pdata->suspend = omap_hsmmc_suspend_cdirq;
> - ? ? ? ? ? ? ? pdata->resume = omap_hsmmc_resume_cdirq;
> ? ? ? ? ? ? ? ?if (pdata->slots[0].cover)
> ? ? ? ? ? ? ? ? ? ? ? ?pdata->slots[0].get_cover_state =
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?omap_hsmmc_get_cover_state;
> @@ -2211,6 +2209,8 @@ static int __init omap_hsmmc_probe(struct platform_device *pdev)
> ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Unable to grab MMC CD IRQ\n");
> ? ? ? ? ? ? ? ? ? ? ? ?goto err_irq_cd;
> ? ? ? ? ? ? ? ?}
> + ? ? ? ? ? ? ? pdata->suspend = omap_hsmmc_suspend_cdirq;
> + ? ? ? ? ? ? ? pdata->resume = omap_hsmmc_resume_cdirq;
> ? ? ? ?}
>
> ? ? ? ?omap_hsmmc_disable_irq(host);
> diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
> index 6de90bf..e64894c 100644
> --- a/include/linux/i2c/twl.h
> +++ b/include/linux/i2c/twl.h
> @@ -141,6 +141,16 @@
> ?#define TWL6030_CHARGER_CTRL_INT_MASK ?0x10
> ?#define TWL6030_CHARGER_FAULT_INT_MASK ? ? ? ? 0x60
>
> +#define TWL6030_MMCCTRL ? ? ? ? ? ? ? ?0xEE
> +#define VMMC_AUTO_OFF ? ? ? ? ? ? ? ? ?(0x1 << 3)
> +#define SW_FC ? ? ? ? ? ? ? ? ? ? ? ? ?(0x1 << 2)
> +#define STS_MMC ? ? ? ? ? ? ? ? ? ? ? ?0x1
> +
> +#define TWL6030_CFG_INPUT_PUPD3 ? ? ? ?0xF2
> +#define MMC_PU ? ? ? ? ? ? ? ? ? ? ? ? (0x1 << 3)
> +#define MMC_PD ? ? ? ? ? ? ? ? ? ? ? ? (0x1 << 2)
> +
> +
>
> ?#define TWL4030_CLASS_ID ? ? ? ? ? ? ? 0x4030
> ?#define TWL6030_CLASS_ID ? ? ? ? ? ? ? 0x6030
> @@ -173,6 +183,27 @@ int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
> ?int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
> ?int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
>
> +/* Card detect Configuration for MMC1 Controller on OMAP4 */
> +#ifdef CONFIG_TWL4030_CORE
> +int twl6030_mmc_card_detect_config(void);
> +#else
> +static inline int twl6030_mmc_card_detect_config(void)
> +{
> + ? ? ? pr_debug("twl6030_mmc_card_detect_config not supported\n");
> + ? ? ? return 0;
> +}
> +#endif
> +
> +/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
> +#ifdef CONFIG_TWL4030_CORE
> +int twl6030_mmc_card_detect(struct device *dev, int slot);
> +#else
> +static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
> +{
> + ? ? ? pr_debug("Call back twl6030_mmc_card_detect not supported\n");
> + ? ? ? return -EIO;
> +}
> +#endif
> ?/*----------------------------------------------------------------------*/
>
> ?/*
> --
> 1.7.0.4
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at ?http://vger.kernel.org/majordomo-info.html
>

  parent reply	other threads:[~2010-09-27  7:55 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-09-24 17:13 [PATCH v4 1/4] omap4 hsmmc: Adding card detect support for MMC1 kishore kadiyala
2010-09-25  0:38 ` Tony Lindgren
2010-09-27  7:52   ` kishore kadiyala
2010-09-27  7:55 ` kishore kadiyala [this message]
2010-09-28  6:52   ` kishore kadiyala
2010-09-29 10:41     ` kishore kadiyala
2010-10-01  6:59       ` kishore kadiyala
2010-10-01 11:29         ` Samuel Ortiz
2010-10-01 12:02           ` kishore kadiyala
2010-10-01 14:41             ` Varadarajan, Charulatha
2010-10-01 14:44               ` kishore kadiyala
2010-10-01 14:54                 ` Varadarajan, Charulatha
2010-10-20 13:11                 ` DebBarma, Tarun Kanti
2010-10-01 14:46 ` Varadarajan, Charulatha

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='AANLkTi=YvtrfmUTc-YBAUjEXn1v3pPLmhb92J60AhU28@mail.gmail.com' \
    --to=kishorek.kadiyala@gmail.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).