From mboxrd@z Thu Jan 1 00:00:00 1970 From: benjamin.gaignard@linaro.org (Benjamin Gaignard) Date: Tue, 13 Dec 2016 10:15:21 +0100 Subject: [PATCH v6 7/8] ARM: dts: stm32: add Timers driver for stm32f429 MCU In-Reply-To: <20161212185943.ph7njaqb2lxtgdn4@rob-hp-laptop> References: <1481292919-26587-1-git-send-email-benjamin.gaignard@st.com> <1481292919-26587-8-git-send-email-benjamin.gaignard@st.com> <20161212185943.ph7njaqb2lxtgdn4@rob-hp-laptop> Message-ID: To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org 2016-12-12 19:59 GMT+01:00 Rob Herring : > On Fri, Dec 09, 2016 at 03:15:18PM +0100, Benjamin Gaignard wrote: >> Add Timers and it sub-nodes into DT for stm32f429 family. >> >> version 6: >> - split patch in two: one for SoC family and one for stm32f469 >> discovery board. >> >> version 5: >> - rename gptimer node to timers >> - re-order timers node par addresses >> >> version 4: >> - remove unwanted indexing in pwm@ and timer@ node name >> - use "reg" instead of additional parameters to set timer >> configuration >> >> version 3: >> - use "st,stm32-timer-trigger" in DT >> >> version 2: >> - use parameters to describe hardware capabilities >> - do not use references for pwm and iio timer subnodes >> >> Signed-off-by: Benjamin Gaignard >> --- >> arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++ >> 1 file changed, 275 insertions(+) >> >> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi >> index bca491d..d0fb9cc 100644 >> --- a/arch/arm/boot/dts/stm32f429.dtsi >> +++ b/arch/arm/boot/dts/stm32f429.dtsi >> @@ -355,6 +355,21 @@ >> slew-rate = <2>; >> }; >> }; >> + >> + pwm1_pins: pwm at 1 { > > No reg prop, so should not have a unit-address. Given the names in the > define below, seems like "timer1" would be appropriate. > >> + pins { >> + pinmux = , >> + , >> + ; >> + }; >> + }; >> + >> + pwm3_pins: pwm at 3 { >> + pins { >> + pinmux = , >> + ; >> + }; >> + }; >> }; >> >> rcc: rcc at 40023810 { >> @@ -426,6 +441,266 @@ >> interrupts = <80>; >> clocks = <&rcc 0 38>; >> }; >> + >> + timers2: timers at 40000000 { > > timer at ... > > It may be more than just a timer, there's not a better generic name. > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000000 0x400>; >> + clocks = <&rcc 0 128>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <1>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers3: timers at 40000400 { > > ditto > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000400 0x400>; >> + clocks = <&rcc 0 129>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <2>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers4: timers at 40000800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000800 0x400>; >> + clocks = <&rcc 0 130>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <3>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers5: timers at 40000C00 { > > timer at ... > > And use lowercase hex. > >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40000C00 0x400>; > > ditto > >> + clocks = <&rcc 0 131>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <4>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers6: timers at 40001000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001000 0x400>; >> + clocks = <&rcc 0 132>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <5>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers7: timers at 40001400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001400 0x400>; >> + clocks = <&rcc 0 133>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <6>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers12: timers at 40001800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001800 0x400>; >> + clocks = <&rcc 0 134>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <9>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers13: timers at 40001C00 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40001C00 0x400>; >> + clocks = <&rcc 0 135>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers14: timers at 40002000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40002000 0x400>; >> + clocks = <&rcc 0 136>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers1: timers at 40010000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40010000 0x400>; >> + clocks = <&rcc 0 160>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <0>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers8: timers at 40010400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40010400 0x400>; >> + clocks = <&rcc 0 161>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <7>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers9: timers at 40014000 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014000 0x400>; >> + clocks = <&rcc 0 176>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + >> + timer { >> + compatible = "st,stm32-timer-trigger"; >> + reg = <8>; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers10: timers at 40014400 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014400 0x400>; >> + clocks = <&rcc 0 177>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> + >> + timers11: timers at 40014800 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + compatible = "st,stm32-timers"; >> + reg = <0x40014800 0x400>; >> + clocks = <&rcc 0 178>; >> + clock-names = "clk_int"; >> + status = "disabled"; >> + >> + pwm { >> + compatible = "st,stm32-pwm"; >> + status = "disabled"; >> + }; >> + }; >> }; >> }; >> >> -- >> 1.9.1 >> -- Benjamin Gaignard Graphic Study Group Linaro.org ? Open source software for ARM SoCs Follow Linaro: Facebook | Twitter | Blog