[PATCH v9 00/10] bind pinconf to pinctrl single

[PATCH v9 00/10] bind pinconf to pinctrl single

[Haojian Zhuang]

Changelog:
v9:
1. Discard bias-autopull.
2. Fully support irqdomain & drop irq generic chip in pl061 gpio.
3. Rename pinctrl_overlapped_gpio_range().

v8:
1. Update allocate irq dynamically in gpio-pl061.
2. Update bias-pullup/bias-pulldown as 4 parameters.
3. Remove bias-disable.
4. Add bias-autopull.
5. Rename input-schmitt-disable to input-schmitt-enable.
6. Discard allocating global gpio number in ascending order.

v7:
1. Discard the method of adding gpio range from pinctrl-single driver.
Use gpiolib driver to support gpio range from DTS instead.
2. Add gpio request function to claim pin in gpio pl061 driver.
3. Adjust the initcall level in gpio pl061 driver.
4. Allocate gpio number from lowest gpio number to highest. The original
implementation is inverted. It's hard to use since it inverted the sequence
of gpio number.
5. Remove the support of pxa910 temporarily since gpio pxa driver need to
be updated for supporting this solution.

v6:
1. Two configuration array will be created for each pin group.
This first array is stored in pcs_function structure. The 32-bit
configruation argument is stored in this array. Driver stores
data while parsing DTS file, and loads these config array if
function selector is indicated.
The second array is stored in pinctrl_map structure. Driver won't
use it directly. So we could avoid to append lookup pinctrl map
method that is introduced in v5.

v5:
1. Move the properties of pinconf into pin group. So those mask
properties could be merged with other pinconf properties.
2. Append lookup pinctrl map method.
3. Append input schmitt disable config parameter.
4. Clean code.

v4:
1. Define gpio range as sub-node, not label. And remove
pinctrl-single,gpio-ranges property.
2. Use new two properties in sub-node, reg &
pinctrl-single,gpio. GPIO number & GPIO function are listed in
the pinctrl-single,gpio property.
3. Reference the names like pinctrl-single,bias.
4. Add compatible name "pinconf-single". If the compatible name is
"pinctrl-single", there's no pinconf. If the compatible name is
"pinconf-single", there's the generic pinconf in pinctrl-single.
5. Update documents.

v3:
1. Add more comments in document.
2. Replace pcs_readl() & pcs_writel() by pcs->read() & pcs->write().
3. Clean code.

v2:
1. Remove "pinctrl-single,gpio-mask". Since GPIO function is one of the
mux function in the pinmux register of both OMAP and PXA/MMP silicons.
Use "pinctrl-single,function-mask" instead.

[PATCH v9 01/10] gpio: add gpio offset in gpio range cells property

[Haojian Zhuang]

Add gpio offset into "gpio-range-cells" property. It's used to support
sparse pinctrl range in gpio chip.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
---
 Documentation/devicetree/bindings/gpio/gpio.txt |    6 +++---
 arch/arm/boot/dts/spear1310.dtsi                |    4 ++--
 arch/arm/boot/dts/spear1340.dtsi                |    4 ++--
 arch/arm/boot/dts/spear310.dtsi                 |    4 ++--
 arch/arm/boot/dts/spear320.dtsi                 |    4 ++--
 drivers/gpio/gpiolib-of.c                       |   15 ++-------------
 6 files changed, 13 insertions(+), 24 deletions(-)

diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index a336287..d933af3 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -98,7 +98,7 @@ announce the pinrange to the pin ctrl subsystem. For example,
 		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
 		reg = <0x1460 0x18>;
 		gpio-controller;
-		gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>;
+		gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
 
     }
 
@@ -107,8 +107,8 @@ where,
 
    Next values specify the base pin and number of pins for the range
    handled by 'qe_pio_e' gpio. In the given example from base pin 20 to
-   pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled
-   by this gpio controller.
+   pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under
+   pinctrl2 with gpio offset 10 is handled by this gpio controller.
 
 The pinctrl node must have "#gpio-range-cells" property to show number of
 arguments to pass with phandle from gpio controllers node.
diff --git a/arch/arm/boot/dts/spear1310.dtsi b/arch/arm/boot/dts/spear1310.dtsi
index 1513c19..122ae94 100644
--- a/arch/arm/boot/dts/spear1310.dtsi
+++ b/arch/arm/boot/dts/spear1310.dtsi
@@ -89,7 +89,7 @@
 		pinmux: pinmux at e0700000 {
 			compatible = "st,spear1310-pinmux";
 			reg = <0xe0700000 0x1000>;
-			#gpio-range-cells = <2>;
+			#gpio-range-cells = <3>;
 		};
 
 		apb {
@@ -212,7 +212,7 @@
 				interrupt-controller;
 				gpio-controller;
 				#gpio-cells = <2>;
-				gpio-ranges = <&pinmux 0 246>;
+				gpio-ranges = <&pinmux 0 0 246>;
 				status = "disabled";
 
 				st-plgpio,ngpio = <246>;
diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi
index b2d41b7..7ec1eb8 100644
--- a/arch/arm/boot/dts/spear1340.dtsi
+++ b/arch/arm/boot/dts/spear1340.dtsi
@@ -63,7 +63,7 @@
 		pinmux: pinmux at e0700000 {
 			compatible = "st,spear1340-pinmux";
 			reg = <0xe0700000 0x1000>;
-			#gpio-range-cells = <2>;
+			#gpio-range-cells = <3>;
 		};
 
 		pwm: pwm at e0180000 {
@@ -146,7 +146,7 @@
 				interrupt-controller;
 				gpio-controller;
 				#gpio-cells = <2>;
-				gpio-ranges = <&pinmux 0 252>;
+				gpio-ranges = <&pinmux 0 0 252>;
 				status = "disabled";
 
 				st-plgpio,ngpio = <250>;
diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi
index ab45b8c..9537208 100644
--- a/arch/arm/boot/dts/spear310.dtsi
+++ b/arch/arm/boot/dts/spear310.dtsi
@@ -25,7 +25,7 @@
 		pinmux: pinmux at b4000000 {
 			compatible = "st,spear310-pinmux";
 			reg = <0xb4000000 0x1000>;
-			#gpio-range-cells = <2>;
+			#gpio-range-cells = <3>;
 		};
 
 		fsmc: flash at 44000000 {
@@ -102,7 +102,7 @@
 				interrupt-controller;
 				gpio-controller;
 				#gpio-cells = <2>;
-				gpio-ranges = <&pinmux 0 102>;
+				gpio-ranges = <&pinmux 0 0 102>;
 				status = "disabled";
 
 				st-plgpio,ngpio = <102>;
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi
index caa5520..ffea342 100644
--- a/arch/arm/boot/dts/spear320.dtsi
+++ b/arch/arm/boot/dts/spear320.dtsi
@@ -24,7 +24,7 @@
 		pinmux: pinmux at b3000000 {
 			compatible = "st,spear320-pinmux";
 			reg = <0xb3000000 0x1000>;
-			#gpio-range-cells = <2>;
+			#gpio-range-cells = <3>;
 		};
 
 		clcd at 90000000 {
@@ -130,7 +130,7 @@
 				interrupt-controller;
 				gpio-controller;
 				#gpio-cells = <2>;
-				gpio-ranges = <&pinmux 0 102>;
+				gpio-ranges = <&pinmux 0 0 102>;
 				status = "disabled";
 
 				st-plgpio,ngpio = <102>;
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a71a54a..892040a 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -203,22 +203,11 @@ static void of_gpiochip_add_pin_range(struct gpio_chip *chip)
 		if (!pctldev)
 			break;
 
-		/*
-		 * This assumes that the n GPIO pins are consecutive in the
-		 * GPIO number space, and that the pins are also consecutive
-		 * in their local number space. Currently it is not possible
-		 * to add different ranges for one and the same GPIO chip,
-		 * as the code assumes that we have one consecutive range
-		 * on both, mapping 1-to-1.
-		 *
-		 * TODO: make the OF bindings handle multiple sparse ranges
-		 * on the same GPIO chip.
-		 */
 		ret = gpiochip_add_pin_range(chip,
 					     pinctrl_dev_get_devname(pctldev),
-					     0, /* offset in gpiochip */
 					     pinspec.args[0],
-					     pinspec.args[1]);
+					     pinspec.args[1],
+					     pinspec.args[2]);
 
 		if (ret)
 			break;
-- 
1.7.10.4

[PATCH v9 02/10] gpio: fix wrong checking condition for gpio range

[Haojian Zhuang]

If index++ calculates from 0, the checking condition of "while
(index++)" fails & it doesn't check any more. It doesn't follow
the loop that used at here.

Replace it by endless loop at here. Then it keeps parsing
"gpio-ranges" property until it ends.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/gpio/gpiolib-of.c |    5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index 892040a..465f4ca 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -193,7 +193,7 @@ static void of_gpiochip_add_pin_range(struct gpio_chip *chip)
 	if (!np)
 		return;
 
-	do {
+	for (;; index++) {
 		ret = of_parse_phandle_with_args(np, "gpio-ranges",
 				"#gpio-range-cells", index, &pinspec);
 		if (ret)
@@ -211,8 +211,7 @@ static void of_gpiochip_add_pin_range(struct gpio_chip *chip)
 
 		if (ret)
 			break;
-
-	} while (index++);
+	}
 }
 
 #else
-- 
1.7.10.4

[PATCH v9 03/10] gpio: pl061: support irqdomain

[Haojian Zhuang]

Drop the support of irq generic chip. Now support irqdomain instead.

Although set_wake() is defined in irq generic chip & it is not really
used in pl061 gpio driver. Drop it at the same time.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 drivers/gpio/gpio-pl061.c |  104 ++++++++++++++++++++++++++++-----------------
 1 file changed, 65 insertions(+), 39 deletions(-)

diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
index b820869..d1d6035 100644
--- a/drivers/gpio/gpio-pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/irq.h>
+#include <linux/irqdomain.h>
 #include <linux/bitops.h>
 #include <linux/workqueue.h>
 #include <linux/gpio.h>
@@ -51,8 +52,7 @@ struct pl061_gpio {
 	spinlock_t		lock;
 
 	void __iomem		*base;
-	int			irq_base;
-	struct irq_chip_generic	*irq_gc;
+	struct irq_domain	*domain;
 	struct gpio_chip	gc;
 
 #ifdef CONFIG_PM
@@ -122,24 +122,20 @@ static int pl061_to_irq(struct gpio_chip *gc, unsigned offset)
 {
 	struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
 
-	if (chip->irq_base <= 0)
-		return -EINVAL;
-
-	return chip->irq_base + offset;
+	return irq_create_mapping(chip->domain, offset);
 }
 
 static int pl061_irq_type(struct irq_data *d, unsigned trigger)
 {
-	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
-	struct pl061_gpio *chip = gc->private;
-	int offset = d->irq - chip->irq_base;
+	struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
+	int offset = irqd_to_hwirq(d);
 	unsigned long flags;
 	u8 gpiois, gpioibe, gpioiev;
 
 	if (offset < 0 || offset >= PL061_GPIO_NR)
 		return -EINVAL;
 
-	raw_spin_lock_irqsave(&gc->lock, flags);
+	spin_lock_irqsave(&chip->lock, flags);
 
 	gpioiev = readb(chip->base + GPIOIEV);
 
@@ -168,7 +164,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger)
 
 	writeb(gpioiev, chip->base + GPIOIEV);
 
-	raw_spin_unlock_irqrestore(&gc->lock, flags);
+	spin_unlock_irqrestore(&chip->lock, flags);
 
 	return 0;
 }
@@ -192,31 +188,61 @@ static void pl061_irq_handler(unsigned irq, struct irq_desc *desc)
 	chained_irq_exit(irqchip, desc);
 }
 
-static void __init pl061_init_gc(struct pl061_gpio *chip, int irq_base)
+static void pl061_irq_mask(struct irq_data *d)
 {
-	struct irq_chip_type *ct;
+	struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
+	u8 mask = 1 << (irqd_to_hwirq(d) % PL061_GPIO_NR);
+	u8 gpioie;
+
+	spin_lock(&chip->lock);
+	gpioie = readb(chip->base + GPIOIE) & ~mask;
+	writeb(gpioie, chip->base + GPIOIE);
+	spin_unlock(&chip->lock);
+}
 
-	chip->irq_gc = irq_alloc_generic_chip("gpio-pl061", 1, irq_base,
-					      chip->base, handle_simple_irq);
-	chip->irq_gc->private = chip;
+static void pl061_irq_unmask(struct irq_data *d)
+{
+	struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
+	u8 mask = 1 << (irqd_to_hwirq(d) % PL061_GPIO_NR);
+	u8 gpioie;
+
+	spin_lock(&chip->lock);
+	gpioie = readb(chip->base + GPIOIE) | mask;
+	writeb(gpioie, chip->base + GPIOIE);
+	spin_unlock(&chip->lock);
+}
+
+static struct irq_chip pl061_irqchip = {
+	.name		= "pl061 gpio",
+	.irq_mask	= pl061_irq_mask,
+	.irq_unmask	= pl061_irq_unmask,
+	.irq_set_type	= pl061_irq_type,
+};
+
+static int pl061_irq_map(struct irq_domain *d, unsigned int virq,
+			 irq_hw_number_t hw)
+{
+	struct pl061_gpio *chip = d->host_data;
 
-	ct = chip->irq_gc->chip_types;
-	ct->chip.irq_mask = irq_gc_mask_clr_bit;
-	ct->chip.irq_unmask = irq_gc_mask_set_bit;
-	ct->chip.irq_set_type = pl061_irq_type;
-	ct->chip.irq_set_wake = irq_gc_set_wake;
-	ct->regs.mask = GPIOIE;
+	irq_set_chip_and_handler_name(virq, &pl061_irqchip, handle_simple_irq,
+				      "pl061");
+	irq_set_chip_data(virq, chip);
+	irq_set_irq_type(virq, IRQ_TYPE_NONE);
 
-	irq_setup_generic_chip(chip->irq_gc, IRQ_MSK(PL061_GPIO_NR),
-			       IRQ_GC_INIT_NESTED_LOCK, IRQ_NOREQUEST, 0);
+	return 0;
 }
 
+static const struct irq_domain_ops pl061_domain_ops = {
+	.map	= pl061_irq_map,
+	.xlate	= irq_domain_xlate_twocell,
+};
+
 static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
 {
 	struct device *dev = &adev->dev;
 	struct pl061_platform_data *pdata = dev->platform_data;
 	struct pl061_gpio *chip;
-	int ret, irq, i;
+	int ret, irq, i, irq_base;
 
 	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
 	if (chip == NULL)
@@ -224,22 +250,28 @@ static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
 
 	if (pdata) {
 		chip->gc.base = pdata->gpio_base;
-		chip->irq_base = pdata->irq_base;
-	} else if (adev->dev.of_node) {
+		irq_base = pdata->irq_base;
+		if (irq_base <= 0)
+			return -ENODEV;
+	} else {
 		chip->gc.base = -1;
-		chip->irq_base = 0;
-	} else
-		return -ENODEV;
+		irq_base = 0;
+	}
 
 	if (!devm_request_mem_region(dev, adev->res.start,
-				resource_size(&adev->res), "pl061"))
+				     resource_size(&adev->res), "pl061"))
 		return -EBUSY;
 
 	chip->base = devm_ioremap(dev, adev->res.start,
-				resource_size(&adev->res));
-	if (chip->base == NULL)
+				  resource_size(&adev->res));
+	if (!chip->base)
 		return -ENOMEM;
 
+	chip->domain = irq_domain_add_simple(adev->dev.of_node, PL061_GPIO_NR,
+					     irq_base, &pl061_domain_ops, chip);
+	if (!chip->domain)
+		return -ENODEV;
+
 	spin_lock_init(&chip->lock);
 
 	chip->gc.direction_input = pl061_direction_input;
@@ -259,12 +291,6 @@ static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
 	/*
 	 * irq_chip support
 	 */
-
-	if (chip->irq_base <= 0)
-		return 0;
-
-	pl061_init_gc(chip, chip->irq_base);
-
 	writeb(0, chip->base + GPIOIE); /* disable irqs */
 	irq = adev->irq[0];
 	if (irq < 0)
-- 
1.7.10.4

[PATCH v9 04/10] pinctrl: check pinctrl ready for gpio range

[Haojian Zhuang]

pinctrl_get_device_gpio_range() only checks whether a certain GPIO pin
is in gpio range. But maybe some GPIO pins don't have back-end pinctrl
interface, it means that these pins are always configured as GPIO
function. For example, gpio159 isn't related to back-end pinctrl device
in Hi3620 while other GPIO pins are related to back-end pinctrl device.

Append pinctrl_ready_for_gpio_range() that is used to check whether
pinctrl device with GPIO range is ready. This function will be called
after pinctrl_get_device_gpio_range() fails.

If pinctrl device with GPIO range is found, it means that pinctrl device
is already launched and a certain GPIO pin just don't have back-end pinctrl
interface. Then pinctrl_request_gpio() shouldn't return -EPROBE_DEFER in
this case.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 drivers/pinctrl/core.c |   36 ++++++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/drivers/pinctrl/core.c b/drivers/pinctrl/core.c
index b0a8e9a..e333dde 100644
--- a/drivers/pinctrl/core.c
+++ b/drivers/pinctrl/core.c
@@ -27,6 +27,7 @@
 #include <linux/pinctrl/consumer.h>
 #include <linux/pinctrl/pinctrl.h>
 #include <linux/pinctrl/machine.h>
+#include <asm-generic/gpio.h>
 #include "core.h"
 #include "devicetree.h"
 #include "pinmux.h"
@@ -293,6 +294,39 @@ pinctrl_match_gpio_range(struct pinctrl_dev *pctldev, unsigned gpio)
 }
 
 /**
+ * pinctrl_ready_for_gpio_range() - check if other GPIO pins of
+ * the same GPIO chip are in range
+ * @gpio: gpio pin to check taken from the global GPIO pin space
+ *
+ * This function is complement of pinctrl_match_gpio_range(). If the return
+ * value of pinctrl_match_gpio_range() is NULL, this function could be used
+ * to check whether pinctrl device is ready or not. Maybe some GPIO pins
+ * of the same GPIO chip don't have back-end pinctrl interface.
+ * If the return value is true, it means that pinctrl device is ready & the
+ * certain GPIO pin doesn't have back-end pinctrl device. If the return value
+ * is false, it means that pinctrl device may not be ready.
+ */
+static bool pinctrl_ready_for_gpio_range(unsigned gpio)
+{
+	struct pinctrl_dev *pctldev;
+	struct pinctrl_gpio_range *range = NULL;
+	struct gpio_chip *chip = gpio_to_chip(gpio);
+
+	/* Loop over the pin controllers */
+	list_for_each_entry(pctldev, &pinctrldev_list, node) {
+		/* Loop over the ranges */
+		list_for_each_entry(range, &pctldev->gpio_ranges, node) {
+			/* Check if any gpio range overlapped with gpio chip */
+			if (range->base + range->npins - 1 < chip->base ||
+			    range->base > chip->base + chip->ngpio - 1)
+				continue;
+			return true;
+		}
+	}
+	return false;
+}
+
+/**
  * pinctrl_get_device_gpio_range() - find device for GPIO range
  * @gpio: the pin to locate the pin controller for
  * @outdev: the pin control device if found
@@ -459,6 +493,8 @@ int pinctrl_request_gpio(unsigned gpio)
 
 	ret = pinctrl_get_device_gpio_range(gpio, &pctldev, &range);
 	if (ret) {
+		if (pinctrl_ready_for_gpio_range(gpio))
+			ret = 0;
 		mutex_unlock(&pinctrl_mutex);
 		return ret;
 	}
-- 
1.7.10.4

[PATCH v9 05/10] gpio: pl061: bind pinctrl by gpio request

[Haojian Zhuang]

Add the pl061_gpio_request() to request pinctrl. Create the logic
between pl061 gpio driver and pinctrl (pinctrl-single) driver.

While a gpio pin is requested, it will request pinctrl driver to
set that pin with gpio function mode. So pinctrl driver should
append .gpio_request_enable() in pinmux_ops.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 drivers/gpio/gpio-pl061.c |   13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
index d1d6035..06ed257 100644
--- a/drivers/gpio/gpio-pl061.c
+++ b/drivers/gpio/gpio-pl061.c
@@ -23,6 +23,7 @@
 #include <linux/amba/bus.h>
 #include <linux/amba/pl061.h>
 #include <linux/slab.h>
+#include <linux/pinctrl/consumer.h>
 #include <linux/pm.h>
 #include <asm/mach/irq.h>
 
@@ -60,6 +61,17 @@ struct pl061_gpio {
 #endif
 };
 
+static int pl061_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+	/*
+	 * Map back to global GPIO space and request muxing, the direction
+	 * parameter does not matter for this controller.
+	 */
+	int gpio = chip->base + offset;
+
+	return pinctrl_request_gpio(gpio);
+}
+
 static int pl061_direction_input(struct gpio_chip *gc, unsigned offset)
 {
 	struct pl061_gpio *chip = container_of(gc, struct pl061_gpio, gc);
@@ -274,6 +286,7 @@ static int pl061_probe(struct amba_device *adev, const struct amba_id *id)
 
 	spin_lock_init(&chip->lock);
 
+	chip->gc.request = pl061_gpio_request;
 	chip->gc.direction_input = pl061_direction_input;
 	chip->gc.direction_output = pl061_direction_output;
 	chip->gc.get = pl061_get_value;
-- 
1.7.10.4

[PATCH v9 06/10] pinctrl: single: create new gpio function range

[Haojian Zhuang]

Since gpio driver could create gpio range in DTS, it could invoke
pinctrl_request_gpio(). In the pinctrl-single driver, it needs to
configure pins with gpio function mode.

A new gpio function range should be created in DTS file in below.

pinctrl-single,gpio-range = <phandle pin_offset nr_pins gpio_func>;

range: gpio-range {
	#pinctrl-single,gpio-range-cells = <3>;
};

The gpio-ranges property is used in gpio driver and the
pinctrl-single,gpio-range property is used in pinctrl-single driver.

1. gpio-ranges is used for gpio driver in below.
   gpio-ranges = <phandle gpio_offset_in_chip pin_offset nr_pins>
	gpio-ranges = < &pmx0 0 89 1 &pmx0 1 89 1 &pmx0 2 90 1
			&pmx0 3 90 1 &pmx0 4 91 1 &pmx0 5 92 1>;

2. gpio driver could get pin offset from gpio-ranges property.
   pinctrl-single driver could get gpio function mode from gpio_func
   that is stored in @gpiofuncs list in struct pcs_device.
   This new pinctrl-single,gpio-range is used as complement for
   gpio-ranges property in gpio driver.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 drivers/pinctrl/pinctrl-single.c |   73 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 71 insertions(+), 2 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index 5c32e88..8b9dd95 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -77,6 +77,20 @@ struct pcs_function {
 };
 
 /**
+ * struct pcs_gpiofunc_range - pin ranges with same mux value of gpio function
+ * @offset:	offset base of pins
+ * @npins:	number pins with the same mux value of gpio function
+ * @gpiofunc:	mux value of gpio function
+ * @node:	list node
+ */
+struct pcs_gpiofunc_range {
+	unsigned offset;
+	unsigned npins;
+	unsigned gpiofunc;
+	struct list_head node;
+};
+
+/**
  * struct pcs_data - wrapper for data needed by pinctrl framework
  * @pa:		pindesc array
  * @cur:	index to current element
@@ -123,6 +137,7 @@ struct pcs_name {
  * @ftree:	function index radix tree
  * @pingroups:	list of pingroups
  * @functions:	list of functions
+ * @gpiofuncs:	list of gpio functions
  * @ngroups:	number of pingroups
  * @nfuncs:	number of functions
  * @desc:	pin controller descriptor
@@ -148,6 +163,7 @@ struct pcs_device {
 	struct radix_tree_root ftree;
 	struct list_head pingroups;
 	struct list_head functions;
+	struct list_head gpiofuncs;
 	unsigned ngroups;
 	unsigned nfuncs;
 	struct pinctrl_desc desc;
@@ -403,9 +419,26 @@ static void pcs_disable(struct pinctrl_dev *pctldev, unsigned fselector,
 }
 
 static int pcs_request_gpio(struct pinctrl_dev *pctldev,
-			struct pinctrl_gpio_range *range, unsigned offset)
+			    struct pinctrl_gpio_range *range, unsigned pin)
 {
-	return -ENOTSUPP;
+	struct pcs_device *pcs = pinctrl_dev_get_drvdata(pctldev);
+	struct pcs_gpiofunc_range *frange = NULL;
+	struct list_head *pos, *tmp;
+	int mux_bytes = 0;
+	unsigned data;
+
+	list_for_each_safe(pos, tmp, &pcs->gpiofuncs) {
+		frange = list_entry(pos, struct pcs_gpiofunc_range, node);
+		if (pin >= frange->offset + frange->npins
+			|| pin < frange->offset)
+			continue;
+		mux_bytes = pcs->width / BITS_PER_BYTE;
+		data = pcs->read(pcs->base + pin * mux_bytes) & ~pcs->fmask;
+		data |= frange->gpiofunc;
+		pcs->write(data, pcs->base + pin * mux_bytes);
+		break;
+	}
+	return 0;
 }
 
 static struct pinmux_ops pcs_pinmux_ops = {
@@ -879,6 +912,37 @@ static void pcs_free_resources(struct pcs_device *pcs)
 
 static struct of_device_id pcs_of_match[];
 
+static int pcs_add_gpio_func(struct device_node *node, struct pcs_device *pcs)
+{
+	const char *propname = "pinctrl-single,gpio-range";
+	const char *cellname = "#pinctrl-single,gpio-range-cells";
+	struct of_phandle_args gpiospec;
+	struct pcs_gpiofunc_range *range;
+	int ret, i;
+
+	for (i = 0; ; i++) {
+		ret = of_parse_phandle_with_args(node, propname, cellname,
+						 i, &gpiospec);
+		/* Do not treat it as error. Only treat it as end condition. */
+		if (ret) {
+			ret = 0;
+			break;
+		}
+		range = devm_kzalloc(pcs->dev, sizeof(*range), GFP_KERNEL);
+		if (!range) {
+			ret = -ENOMEM;
+			break;
+		}
+		range->offset = gpiospec.args[0];
+		range->npins = gpiospec.args[1];
+		range->gpiofunc = gpiospec.args[2];
+		mutex_lock(&pcs->mutex);
+		list_add_tail(&range->node, &pcs->gpiofuncs);
+		mutex_unlock(&pcs->mutex);
+	}
+	return ret;
+}
+
 static int pcs_probe(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
@@ -900,6 +964,7 @@ static int pcs_probe(struct platform_device *pdev)
 	mutex_init(&pcs->mutex);
 	INIT_LIST_HEAD(&pcs->pingroups);
 	INIT_LIST_HEAD(&pcs->functions);
+	INIT_LIST_HEAD(&pcs->gpiofuncs);
 
 	PCS_GET_PROP_U32("pinctrl-single,register-width", &pcs->width,
 			 "register width not specified\n");
@@ -975,6 +1040,10 @@ static int pcs_probe(struct platform_device *pdev)
 		goto free;
 	}
 
+	ret = pcs_add_gpio_func(np, pcs);
+	if (ret < 0)
+		goto free;
+
 	dev_info(pcs->dev, "%i pins at pa %p size %u\n",
 		 pcs->desc.npins, pcs->base, pcs->size);
 
-- 
1.7.10.4

[PATCH v9 07/10] pinctrl: generic: dump pin configuration

[Haojian Zhuang]

Add the support of dumping pin configuration.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
---
 drivers/pinctrl/pinconf-generic.c |   14 ++++++++++++++
 drivers/pinctrl/pinconf.h         |    8 ++++++++
 2 files changed, 22 insertions(+)

diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c
index e5948f8..ef24230 100644
--- a/drivers/pinctrl/pinconf-generic.c
+++ b/drivers/pinctrl/pinconf-generic.c
@@ -12,6 +12,7 @@
 #define pr_fmt(fmt) "generic pinconfig core: " fmt
 
 #include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/slab.h>
@@ -120,4 +121,17 @@ void pinconf_generic_dump_group(struct pinctrl_dev *pctldev,
 	}
 }
 
+void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
+				 struct seq_file *s, unsigned long config)
+{
+	int i;
+
+	for(i = 0; i < ARRAY_SIZE(conf_items); i++) {
+		if (pinconf_to_config_param(config) != conf_items[i].param)
+			continue;
+		seq_printf(s, "%s: 0x%x", conf_items[i].display,
+			   pinconf_to_config_argument(config));
+	}
+}
+EXPORT_SYMBOL_GPL(pinconf_generic_dump_config);
 #endif
diff --git a/drivers/pinctrl/pinconf.h b/drivers/pinctrl/pinconf.h
index e3ed8cb..1f7113e 100644
--- a/drivers/pinctrl/pinconf.h
+++ b/drivers/pinctrl/pinconf.h
@@ -98,6 +98,8 @@ void pinconf_generic_dump_pin(struct pinctrl_dev *pctldev,
 void pinconf_generic_dump_group(struct pinctrl_dev *pctldev,
 			      struct seq_file *s, const char *gname);
 
+void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
+				 struct seq_file *s, unsigned long config);
 #else
 
 static inline void pinconf_generic_dump_pin(struct pinctrl_dev *pctldev,
@@ -114,4 +116,10 @@ static inline void pinconf_generic_dump_group(struct pinctrl_dev *pctldev,
 	return;
 }
 
+static inline void pinconf_generic_dump_config(struct pinctrl_dev *pctldev,
+					       struct seq_file *s,
+					       unsigned long config)
+{
+	return;
+}
 #endif
-- 
1.7.10.4

[PATCH v9 08/10] pinctrl: single: set function mask as optional

[Haojian Zhuang]

Since Hisilicon's pin controller is divided into two parts. One is the
function mux, and the other is pin configuration. These two parts are
in the different memory regions. So make pinctrl-single,function-mask
as optional property. Then we can define pingroups without valid
function mux that is only used for pin configuration.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 drivers/pinctrl/pinctrl-single.c |   26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index 8b9dd95..fe8f321 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -350,6 +350,9 @@ static int pcs_enable(struct pinctrl_dev *pctldev, unsigned fselector,
 	int i;
 
 	pcs = pinctrl_dev_get_drvdata(pctldev);
+	/* If function mask is null, needn't enable it. */
+	if (!pcs->fmask)
+		return 0;
 	func = radix_tree_lookup(&pcs->ftree, fselector);
 	if (!func)
 		return -EINVAL;
@@ -384,6 +387,10 @@ static void pcs_disable(struct pinctrl_dev *pctldev, unsigned fselector,
 	int i;
 
 	pcs = pinctrl_dev_get_drvdata(pctldev);
+	/* If function mask is null, needn't disable it. */
+	if (!pcs->fmask)
+		return;
+
 	func = radix_tree_lookup(&pcs->ftree, fselector);
 	if (!func) {
 		dev_err(pcs->dev, "%s could not find function%i\n",
@@ -427,6 +434,10 @@ static int pcs_request_gpio(struct pinctrl_dev *pctldev,
 	int mux_bytes = 0;
 	unsigned data;
 
+	/* If function mask is null, return directly. */
+	if (!pcs->fmask)
+		return -ENOTSUPP;
+
 	list_for_each_safe(pos, tmp, &pcs->gpiofuncs) {
 		frange = list_entry(pos, struct pcs_gpiofunc_range, node);
 		if (pin >= frange->offset + frange->npins
@@ -969,10 +980,17 @@ static int pcs_probe(struct platform_device *pdev)
 	PCS_GET_PROP_U32("pinctrl-single,register-width", &pcs->width,
 			 "register width not specified\n");
 
-	PCS_GET_PROP_U32("pinctrl-single,function-mask", &pcs->fmask,
-			 "function register mask not specified\n");
-	pcs->fshift = ffs(pcs->fmask) - 1;
-	pcs->fmax = pcs->fmask >> pcs->fshift;
+	ret = of_property_read_u32(np, "pinctrl-single,function-mask",
+				   &pcs->fmask);
+	if (!ret) {
+		pcs->fshift = ffs(pcs->fmask) - 1;
+		pcs->fmax = pcs->fmask >> pcs->fshift;
+	} else {
+		/* If mask property doesn't exist, function mux is invalid. */
+		pcs->fmask = 0;
+		pcs->fshift = 0;
+		pcs->fmax = 0;
+	}
 
 	ret = of_property_read_u32(np, "pinctrl-single,function-off",
 					&pcs->foff);
-- 
1.7.10.4

[PATCH v9 09/10] pinctrl: single: support generic pinconf

[Haojian Zhuang]

Support the operation of generic pinconf. The supported config arguments
are INPUT_SCHMITT, INPUT_SCHMITT_ENABLE, DRIVE_STRENGHT, BIAS_DISABLE,
BIAS_PULLUP, BIAS_PULLDOWN, SLEW_RATE.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 drivers/pinctrl/Kconfig          |    1 +
 drivers/pinctrl/pinctrl-single.c |  408 +++++++++++++++++++++++++++++++++++++-
 2 files changed, 402 insertions(+), 7 deletions(-)

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 34f51d2..5a690ce 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -166,6 +166,7 @@ config PINCTRL_SINGLE
 	depends on OF
 	select PINMUX
 	select PINCONF
+	select GENERIC_PINCONF
 	help
 	  This selects the device tree based generic pinctrl driver.
 
diff --git a/drivers/pinctrl/pinctrl-single.c b/drivers/pinctrl/pinctrl-single.c
index fe8f321..7b557e2 100644
--- a/drivers/pinctrl/pinctrl-single.c
+++ b/drivers/pinctrl/pinctrl-single.c
@@ -22,8 +22,10 @@
 
 #include <linux/pinctrl/pinctrl.h>
 #include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/pinconf-generic.h>
 
 #include "core.h"
+#include "pinconf.h"
 
 #define DRIVER_NAME			"pinctrl-single"
 #define PCS_MUX_PINS_NAME		"pinctrl-single,pins"
@@ -59,6 +61,33 @@ struct pcs_func_vals {
 };
 
 /**
+ * struct pcs_conf_vals - pinconf parameter, pinconf register offset
+ * and value, enable, disable, mask
+ * @param:	config parameter
+ * @val:	user input bits in the pinconf register
+ * @enable:	enable bits in the pinconf register
+ * @disable:	disable bits in the pinconf register
+ * @mask:	mask bits in the register value
+ */
+struct pcs_conf_vals {
+	enum pin_config_param param;
+	unsigned val;
+	unsigned enable;
+	unsigned disable;
+	unsigned mask;
+};
+
+/**
+ * struct pcs_conf_type - pinconf property name, pinconf param pair
+ * @name:	property name in DTS file
+ * @param:	config parameter
+ */
+struct pcs_conf_type {
+	const char *name;
+	enum pin_config_param param;
+};
+
+/**
  * struct pcs_function - pinctrl function
  * @name:	pinctrl function name
  * @vals:	register and vals array
@@ -73,6 +102,8 @@ struct pcs_function {
 	unsigned nvals;
 	const char **pgnames;
 	int npgnames;
+	struct pcs_conf_vals *conf;
+	int nconfs;
 	struct list_head node;
 };
 
@@ -131,6 +162,7 @@ struct pcs_name {
  * @fshift:	function register shift
  * @foff:	value to turn mux off
  * @fmax:	max number of functions in fmask
+ * @is_pinconf:	whether supports pinconf
  * @names:	array of register names for pins
  * @pins:	physical pins on the SoC
  * @pgtree:	pingroup index radix tree
@@ -157,6 +189,7 @@ struct pcs_device {
 	unsigned foff;
 	unsigned fmax;
 	bool bits_per_mux;
+	bool is_pinconf;
 	struct pcs_name *names;
 	struct pcs_data pins;
 	struct radix_tree_root pgtree;
@@ -171,6 +204,16 @@ struct pcs_device {
 	void (*write)(unsigned val, void __iomem *reg);
 };
 
+static int pcs_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin,
+			   unsigned long *config);
+static int pcs_pinconf_set(struct pinctrl_dev *pctldev, unsigned pin,
+			   unsigned long config);
+
+static enum pin_config_param pcs_bias[] = {
+	PIN_CONFIG_BIAS_PULL_DOWN,
+	PIN_CONFIG_BIAS_PULL_UP,
+};
+
 /*
  * REVISIT: Reads and writes could eventually use regmap or something
  * generic. But at least on omaps, some mux registers are performance
@@ -342,6 +385,28 @@ static int pcs_get_function_groups(struct pinctrl_dev *pctldev,
 	return 0;
 }
 
+static int pcs_get_function(struct pinctrl_dev *pctldev, unsigned pin,
+			    struct pcs_function **func)
+{
+	struct pcs_device *pcs = pinctrl_dev_get_drvdata(pctldev);
+	struct pin_desc *pdesc = pin_desc_get(pctldev, pin);
+	const struct pinctrl_setting_mux *setting;
+	unsigned fselector;
+
+	/* If pin is not described in DTS & enabled, mux_setting is NULL. */
+	setting = pdesc->mux_setting;
+	if (!setting)
+		return -ENOTSUPP;
+	fselector = setting->func;
+	*func = radix_tree_lookup(&pcs->ftree, fselector);
+	if (!(*func)) {
+		dev_err(pcs->dev, "%s could not find function%i\n",
+			__func__, fselector);
+		return -ENOTSUPP;
+	}
+	return 0;
+}
+
 static int pcs_enable(struct pinctrl_dev *pctldev, unsigned fselector,
 	unsigned group)
 {
@@ -461,32 +526,191 @@ static struct pinmux_ops pcs_pinmux_ops = {
 	.gpio_request_enable = pcs_request_gpio,
 };
 
+/* Clear BIAS value */
+static void pcs_pinconf_clear_bias(struct pinctrl_dev *pctldev, unsigned pin)
+{
+	unsigned long config;
+	int i;
+	for (i = 0; i < ARRAY_SIZE(pcs_bias); i++) {
+		config = pinconf_to_config_packed(pcs_bias[i], 0);
+		pcs_pinconf_set(pctldev, pin, config);
+	}
+}
+
+/*
+ * Check whether PIN_CONFIG_BIAS_DISABLE is valid.
+ * It's depend on that PULL_DOWN & PULL_UP configs are all invalid.
+ */
+static bool pcs_pinconf_bias_disable(struct pinctrl_dev *pctldev, unsigned pin)
+{
+	unsigned long config;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcs_bias); i++) {
+		config = pinconf_to_config_packed(pcs_bias[i], 0);
+		if (!pcs_pinconf_get(pctldev, pin, &config))
+			goto out;
+	}
+	return true;
+out:
+	return false;
+}
+
 static int pcs_pinconf_get(struct pinctrl_dev *pctldev,
 				unsigned pin, unsigned long *config)
 {
+	struct pcs_device *pcs = pinctrl_dev_get_drvdata(pctldev);
+	struct pcs_function *func;
+	enum pin_config_param param;
+	unsigned offset = 0, data = 0, i, j, ret;
+
+	ret = pcs_get_function(pctldev, pin, &func);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < func->nconfs; i++) {
+		param = pinconf_to_config_param(*config);
+		if (param == PIN_CONFIG_BIAS_DISABLE) {
+			if (pcs_pinconf_bias_disable(pctldev, pin)) {
+				*config = 0;
+				return 0;
+			} else {
+				return -ENOTSUPP;
+			}
+		} else if (param != func->conf[i].param) {
+			continue;
+		}
+
+		offset = pin * (pcs->width / BITS_PER_BYTE);
+		data = pcs->read(pcs->base + offset) & func->conf[i].mask;
+		switch (func->conf[i].param) {
+		/* 4 parameters */
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+		case PIN_CONFIG_BIAS_PULL_UP:
+		case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+			if ((data != func->conf[i].enable) ||
+			    (data == func->conf[i].disable))
+				return -ENOTSUPP;
+			*config = 0;
+			break;
+		/* 2 parameters */
+		case PIN_CONFIG_INPUT_SCHMITT:
+			for (j = 0; j < func->nconfs; j++) {
+				switch (func->conf[j].param) {
+				case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+					if (data != func->conf[j].enable)
+						return -ENOTSUPP;
+					break;
+				default:
+					break;
+				}
+			}
+			*config = data;
+			break;
+		case PIN_CONFIG_DRIVE_STRENGTH:
+		case PIN_CONFIG_SLEW_RATE:
+		default:
+			*config = data;
+			break;
+		}
+		return 0;
+	}
 	return -ENOTSUPP;
 }
 
 static int pcs_pinconf_set(struct pinctrl_dev *pctldev,
 				unsigned pin, unsigned long config)
 {
+	struct pcs_device *pcs = pinctrl_dev_get_drvdata(pctldev);
+	struct pcs_function *func;
+	unsigned offset = 0, shift = 0, arg = 0, i, data, ret;
+	u16 argument;
+
+	ret = pcs_get_function(pctldev, pin, &func);
+	if (ret)
+		return ret;
+
+	for (i = 0; i < func->nconfs; i++) {
+		if (pinconf_to_config_param(config) == func->conf[i].param) {
+			offset = pin * (pcs->width / BITS_PER_BYTE);
+			data = pcs->read(pcs->base + offset);
+			argument = pinconf_to_config_argument(config);
+			switch (func->conf[i].param) {
+			/* 2 parameters */
+			case PIN_CONFIG_INPUT_SCHMITT:
+			case PIN_CONFIG_DRIVE_STRENGTH:
+			case PIN_CONFIG_SLEW_RATE:
+				shift = ffs(func->conf[i].mask) - 1;
+				arg = pinconf_to_config_argument(config);
+				data &= ~func->conf[i].mask;
+				data |= (arg << shift) & func->conf[i].mask;
+				break;
+			/* 4 parameters */
+			case PIN_CONFIG_BIAS_DISABLE:
+				pcs_pinconf_clear_bias(pctldev, pin);
+				break;
+			case PIN_CONFIG_BIAS_PULL_DOWN:
+			case PIN_CONFIG_BIAS_PULL_UP:
+				if (argument)
+					pcs_pinconf_clear_bias(pctldev, pin);
+				/* fall through */
+			case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
+				data &= ~func->conf[i].mask;
+				if (argument)
+					data |= func->conf[i].enable;
+				else
+					data |= func->conf[i].disable;
+				break;
+			default:
+				return -ENOTSUPP;
+			}
+			pcs->write(data, pcs->base + offset);
+			return 0;
+		}
+	}
 	return -ENOTSUPP;
 }
 
 static int pcs_pinconf_group_get(struct pinctrl_dev *pctldev,
 				unsigned group, unsigned long *config)
 {
-	return -ENOTSUPP;
+	const unsigned *pins;
+	unsigned npins, old = 0;
+	int i, ret;
+
+	ret = pcs_get_group_pins(pctldev, group, &pins, &npins);
+	if (ret)
+		return ret;
+	for (i = 0; i < npins; i++) {
+		if (pcs_pinconf_get(pctldev, pins[i], config))
+			return -ENOTSUPP;
+		/* configs do not match between two pins */
+		if (i && (old != *config))
+			return -ENOTSUPP;
+		old = *config;
+	}
+	return 0;
 }
 
 static int pcs_pinconf_group_set(struct pinctrl_dev *pctldev,
 				unsigned group, unsigned long config)
 {
-	return -ENOTSUPP;
+	const unsigned *pins;
+	unsigned npins;
+	int i, ret;
+
+	ret = pcs_get_group_pins(pctldev, group, &pins, &npins);
+	if (ret)
+		return ret;
+	for (i = 0; i < npins; i++) {
+		if (pcs_pinconf_set(pctldev, pins[i], config))
+			return -ENOTSUPP;
+	}
+	return 0;
 }
 
 static void pcs_pinconf_dbg_show(struct pinctrl_dev *pctldev,
-				struct seq_file *s, unsigned offset)
+				struct seq_file *s, unsigned pin)
 {
 }
 
@@ -495,6 +719,13 @@ static void pcs_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
 {
 }
 
+static void pcs_pinconf_config_dbg_show(struct pinctrl_dev *pctldev,
+					struct seq_file *s,
+					unsigned long config)
+{
+	pinconf_generic_dump_config(pctldev, s, config);
+}
+
 static struct pinconf_ops pcs_pinconf_ops = {
 	.pin_config_get = pcs_pinconf_get,
 	.pin_config_set = pcs_pinconf_set,
@@ -502,6 +733,7 @@ static struct pinconf_ops pcs_pinconf_ops = {
 	.pin_config_group_set = pcs_pinconf_group_set,
 	.pin_config_dbg_show = pcs_pinconf_dbg_show,
 	.pin_config_group_dbg_show = pcs_pinconf_group_dbg_show,
+	.pin_config_config_dbg_show = pcs_pinconf_config_dbg_show,
 };
 
 /**
@@ -692,11 +924,157 @@ static int pcs_get_pin_by_offset(struct pcs_device *pcs, unsigned offset)
 	return index;
 }
 
+/*
+ * check whether data matches enable bits or disable bits
+ * Return value: 1 for matching enable bits, 0 for matching disable bits,
+ *               and negative value for matching failure.
+ */
+static int pcs_config_match(unsigned data, unsigned enable, unsigned disable)
+{
+	int ret = -EINVAL;
+
+	if (data == enable)
+		ret = 1;
+	else if (data == disable)
+		ret = 0;
+	return ret;
+}
+
+static void add_config(struct pcs_conf_vals **conf, enum pin_config_param param,
+		       unsigned value, unsigned enable, unsigned disable,
+		       unsigned mask)
+{
+	(*conf)->param = param;
+	(*conf)->val = value;
+	(*conf)->enable = enable;
+	(*conf)->disable = disable;
+	(*conf)->mask = mask;
+	(*conf)++;
+}
+
+static void add_setting(unsigned long **setting, enum pin_config_param param,
+			unsigned arg)
+{
+	**setting = pinconf_to_config_packed(param, arg);
+	(*setting)++;
+}
+
+/* add pinconf setting with 2 parameters */
+static void pcs_add_conf2(struct pcs_device *pcs, struct device_node *np,
+			  const char *name, enum pin_config_param param,
+			  struct pcs_conf_vals **conf, unsigned long **settings)
+{
+	unsigned value[2];
+	int ret;
+
+	ret = of_property_read_u32_array(np, name, value, 2);
+	if (ret)
+		return;
+	/* set value & mask */
+	value[0] &= value[1];
+	/* skip enable & disable */
+	add_config(conf, param, value[0], 0, 0, value[1]);
+	add_setting(settings, param, value[0]);
+}
+
+/* add pinconf setting with 4 parameters */
+static void pcs_add_conf4(struct pcs_device *pcs, struct device_node *np,
+			  const char *name, enum pin_config_param param,
+			  struct pcs_conf_vals **conf, unsigned long **settings)
+{
+	unsigned value[4];
+	int ret;
+
+	/* value to set, enable, disable, mask */
+	ret = of_property_read_u32_array(np, name, value, 4);
+	if (ret)
+		return;
+	if (!value[3]) {
+		dev_err(pcs->dev, "mask field of the property can't be 0\n");
+		return;
+	}
+	value[0] &= value[3];
+	value[1] &= value[3];
+	value[2] &= value[3];
+	ret = pcs_config_match(value[0], value[1], value[2]);
+	if (ret < 0)
+		dev_dbg(pcs->dev, "failed to match enable or disable bits\n");
+	add_config(conf, param, value[0], value[1], value[2], value[3]);
+	add_setting(settings, param, ret);
+}
+
+static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
+			     struct pcs_function *func,
+			     struct pinctrl_map **map)
+
+{
+	struct pinctrl_map *m = *map;
+	int i = 0, nconfs = 0;
+	unsigned long *settings = NULL, *s = NULL;
+	struct pcs_conf_vals *conf = NULL;
+	struct pcs_conf_type prop2[] = {
+		{ "pinctrl-single,drive-strength", PIN_CONFIG_DRIVE_STRENGTH, },
+		{ "pinctrl-single,slew-rate", PIN_CONFIG_SLEW_RATE, },
+		{ "pinctrl-single,input-schmitt", PIN_CONFIG_INPUT_SCHMITT, },
+	};
+	struct pcs_conf_type prop4[] = {
+		{ "pinctrl-single,bias-pullup", PIN_CONFIG_BIAS_PULL_UP, },
+		{ "pinctrl-single,bias-pulldown", PIN_CONFIG_BIAS_PULL_DOWN, },
+		{ "pinctrl-single,input-schmitt-enable",
+			PIN_CONFIG_INPUT_SCHMITT_ENABLE, },
+	};
+
+	/* If pinconf isn't supported, don't parse properties in below. */
+	if (!pcs->is_pinconf)
+		return 0;
+
+	/* cacluate how much properties are supported in current node */
+	for (i = 0; i < ARRAY_SIZE(prop2); i++) {
+		if (of_find_property(np, prop2[i].name, NULL))
+			nconfs++;
+	}
+	for (i = 0; i < ARRAY_SIZE(prop4); i++) {
+		if (of_find_property(np, prop4[i].name, NULL))
+			nconfs++;
+	}
+	if (!nconfs)
+		return 0;
+
+	func->conf = devm_kzalloc(pcs->dev,
+				  sizeof(struct pcs_conf_vals) * nconfs,
+				  GFP_KERNEL);
+	if (!func->conf)
+		return -ENOMEM;
+	func->nconfs = nconfs;
+	conf = &(func->conf[0]);
+	m++;
+	settings = devm_kzalloc(pcs->dev, sizeof(unsigned long) * nconfs,
+				GFP_KERNEL);
+	if (!settings)
+		return -ENOMEM;
+	s = &settings[0];
+
+	for (i = 0; i < ARRAY_SIZE(prop2); i++)
+		pcs_add_conf2(pcs, np, prop2[i].name, prop2[i].param,
+			      &conf, &s);
+	for (i = 0; i < ARRAY_SIZE(prop4); i++)
+		pcs_add_conf4(pcs, np, prop4[i].name, prop4[i].param,
+			      &conf, &s);
+	m->type = PIN_MAP_TYPE_CONFIGS_GROUP;
+	m->data.configs.group_or_pin = np->name;
+	m->data.configs.configs = settings;
+	m->data.configs.num_configs = nconfs;
+	return 0;
+}
+
+static void pcs_free_pingroups(struct pcs_device *pcs);
+
 /**
  * smux_parse_one_pinctrl_entry() - parses a device tree mux entry
  * @pcs: pinctrl driver instance
  * @np: device node of the mux entry
  * @map: map entry
+ * @num_maps: number of map
  * @pgnames: pingroup names
  *
  * Note that this binding currently supports only sets of one register + value.
@@ -713,6 +1091,7 @@ static int pcs_get_pin_by_offset(struct pcs_device *pcs, unsigned offset)
 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 						struct device_node *np,
 						struct pinctrl_map **map,
+						unsigned *num_maps,
 						const char **pgnames)
 {
 	struct pcs_func_vals *vals;
@@ -785,8 +1164,18 @@ static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 	(*map)->data.mux.group = np->name;
 	(*map)->data.mux.function = np->name;
 
+	if (pcs->is_pinconf) {
+		if (pcs_parse_pinconf(pcs, np, function, map))
+			goto free_pingroups;
+		*num_maps = 2;
+	} else {
+		*num_maps = 1;
+	}
 	return 0;
 
+free_pingroups:
+	pcs_free_pingroups(pcs);
+	*num_maps = 1;
 free_function:
 	pcs_remove_function(pcs, function);
 
@@ -815,7 +1204,8 @@ static int pcs_dt_node_to_map(struct pinctrl_dev *pctldev,
 
 	pcs = pinctrl_dev_get_drvdata(pctldev);
 
-	*map = devm_kzalloc(pcs->dev, sizeof(**map), GFP_KERNEL);
+	/* create 2 maps. One is for pinmux, and the other is for pinconf. */
+	*map = devm_kzalloc(pcs->dev, sizeof(**map) * 2, GFP_KERNEL);
 	if (!*map)
 		return -ENOMEM;
 
@@ -827,13 +1217,13 @@ static int pcs_dt_node_to_map(struct pinctrl_dev *pctldev,
 		goto free_map;
 	}
 
-	ret = pcs_parse_one_pinctrl_entry(pcs, np_config, map, pgnames);
+	ret = pcs_parse_one_pinctrl_entry(pcs, np_config, map, num_maps,
+					  pgnames);
 	if (ret < 0) {
 		dev_err(pcs->dev, "no pins entries for %s\n",
 			np_config->name);
 		goto free_pgnames;
 	}
-	*num_maps = 1;
 
 	return 0;
 
@@ -976,6 +1366,7 @@ static int pcs_probe(struct platform_device *pdev)
 	INIT_LIST_HEAD(&pcs->pingroups);
 	INIT_LIST_HEAD(&pcs->functions);
 	INIT_LIST_HEAD(&pcs->gpiofuncs);
+	pcs->is_pinconf = match->data;
 
 	PCS_GET_PROP_U32("pinctrl-single,register-width", &pcs->width,
 			 "register width not specified\n");
@@ -1046,6 +1437,8 @@ static int pcs_probe(struct platform_device *pdev)
 	pcs->desc.pmxops = &pcs_pinmux_ops;
 	pcs->desc.confops = &pcs_pinconf_ops;
 	pcs->desc.owner = THIS_MODULE;
+	if (match->data)
+		pcs_pinconf_ops.is_generic = true;
 
 	ret = pcs_allocate_pin_table(pcs);
 	if (ret < 0)
@@ -1086,7 +1479,8 @@ static int pcs_remove(struct platform_device *pdev)
 }
 
 static struct of_device_id pcs_of_match[] = {
-	{ .compatible = DRIVER_NAME, },
+	{ .compatible = "pinctrl-single", .data = (void *)false },
+	{ .compatible = "pinconf-single", .data = (void *)true },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, pcs_of_match);
-- 
1.7.10.4

[PATCH v9 10/10] document: devicetree: bind pinconf with pin single

[Haojian Zhuang]

From: Haojian Zhuang <haojian.zhuang@gmail.com>

Add comments with pinconf & gpio range in the document of
pinctrl-single.

Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
---
 .../devicetree/bindings/pinctrl/pinctrl-single.txt |  107 +++++++++++++++++++-
 1 file changed, 106 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
index 2c81e45..fa1746b 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -1,7 +1,9 @@
 One-register-per-pin type device tree based pinctrl driver
 
 Required properties:
-- compatible : "pinctrl-single"
+- compatible : "pinctrl-single" or "pinconf-single".
+  "pinctrl-single" means that pinconf isn't supported.
+  "pinconf-single" means that generic pinconf is supported.
 
 - reg : offset and length of the register set for the mux registers
 
@@ -14,9 +16,61 @@ Optional properties:
 - pinctrl-single,function-off : function off mode for disabled state if
   available and same for all registers; if not specified, disabling of
   pin functions is ignored
+
 - pinctrl-single,bit-per-mux : boolean to indicate that one register controls
   more than one pin
 
+- pinctrl-single,drive-strength : array of value that are used to configure
+  drive strength in the pinmux register. They're value of drive strength
+  current and drive strength mask.
+
+		/* drive strength current, mask */
+		pinctrl-single,power-source = <0x30 0xf0>;
+
+- pinctrl-single,bias-pullup : array of value that are used to configure the
+  input bias pullup in the pinmux register.
+
+		/* input, enabled pullup bits, disabled pullup bits, mask */
+		pinctrl-single,bias-pullup = <0 1 0 1>;
+
+- pinctrl-single,bias-pulldown : array of value that are used to configure the
+  input bias pulldown in the pinmux register.
+
+		/* input, enabled pulldown bits, disabled pulldown bits, mask */
+		pinctrl-single,bias-pulldown = <2 2 0 2>;
+
+  * Two bits to control input bias pullup and pulldown: User should use
+    pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
+    pullup, and the other one bit means pulldown.
+  * Three bits to control input bias enable, pullup and pulldown. User should
+    use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
+    enable bit should be included in pullup or pulldown bits.
+  * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
+    pinctrl-single,bias-disable. Because pinctrl single driver could implement
+    it by calling pulldown, pullup disabled.
+
+- pinctrl-single,input-schmitt : array of value that are used to configure
+  input schmitt in the pinmux register. In some silicons, there're two input
+  schmitt value (rising-edge & falling-edge) in the pinmux register.
+
+		/* input schmitt value, mask */
+		pinctrl-single,input-schmitt = <0x30 0x70>;
+
+- pinctrl-single,input-schmitt-enable : array of value that are used to
+  configure input schmitt enable or disable in the pinmux register.
+
+		/* input, enable bits, disable bits, mask */
+		pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
+
+- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
+  range. They're value of subnode phandle, pin base in pinctrl device, pin
+  number in this range, GPIO function value of this GPIO range.
+  The number of parameters is depend on #pinctrl-single,gpio-range-cells
+  property.
+
+		/* pin base, nr pins & gpio function */
+		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
+
 This driver assumes that there is only one register for each pin (unless the
 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
@@ -42,6 +96,20 @@ Where 0xdc is the offset from the pinctrl register base address for the
 device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
 be used when applying this change to the register.
 
+
+Optional sub-node: In case some pins could be configured as GPIO in the pinmux
+register, those pins could be defined as a GPIO range. This sub-node is required
+by pinctrl-single,gpio-range property.
+
+Required properties in sub-node:
+- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
+  pinctrl-single,gpio-range property.
+
+	range: gpio-range {
+		#pinctrl-single,gpio-range-cells = <3>;
+	};
+
+
 Example:
 
 /* SoC common file */
@@ -76,6 +144,29 @@ control_devconf0: pinmux at 48002274 {
 	pinctrl-single,function-mask = <0x5F>;
 };
 
+/* third controller instance for pins in gpio domain */
+pmx_gpio: pinmux at d401e000 {
+	compatible = "pinconf-single";
+	reg = <0xd401e000 0x0330>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	pinctrl-single,register-width = <32>;
+	pinctrl-single,function-mask = <7>;
+
+	/* sparse GPIO range could be supported */
+	pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+				&range 12 1 0 &range 13 29 1
+				&range 43 1 0 &range 44 49 1
+				&range 94 1 1 &range 96 2 1>;
+
+	range: gpio-range {
+		#pinctrl-single,gpio-range-cells = <3>;
+	};
+};
+
+
 /* board specific .dts file */
 
 &pmx_core {
@@ -96,6 +187,15 @@ control_devconf0: pinmux at 48002274 {
 		>;
 	};
 
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x208 0		/* UART0_RXD (IOCFG138) */
+			0x20c 0		/* UART0_TXD (IOCFG139) */
+		>;
+		pinctrl-single,bias-pulldown = <0 2 2>;
+		pinctrl-single,bias-pullup = <0 1 1>;
+	};
+
 	/* map uart2 pins */
 	uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
@@ -122,6 +222,11 @@ control_devconf0: pinmux@48002274 {
 
 };
 
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins>;
+};
+
 &uart2 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart2_pins>;
-- 
1.7.10.4

[PATCH v9 01/10] gpio: add gpio offset in gpio range cells property

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Add gpio offset into "gpio-range-cells" property. It's used to support
> sparse pinctrl range in gpio chip.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>

OK I have applied this to the pinctrl tree for v3.10 to keep all pinctrl changes
together.

Thanks!
Linus Walleij

[PATCH v9 02/10] gpio: fix wrong checking condition for gpio range

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> If index++ calculates from 0, the checking condition of "while
> (index++)" fails & it doesn't check any more. It doesn't follow
> the loop that used at here.
>
> Replace it by endless loop at here. Then it keeps parsing
> "gpio-ranges" property until it ends.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Patch applied to the fixes branch for the v3.9-rc series in
my pinctrl tree.

Yours,
Linus Walleij

[PATCH v9 03/10] gpio: pl061: support irqdomain

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Drop the support of irq generic chip. Now support irqdomain instead.
>
> Although set_wake() is defined in irq generic chip & it is not really
> used in pl061 gpio driver. Drop it at the same time.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Patch applied to my pinctrl tree to avoid clashes between the GPIO
and pinctrl trees later.

Yours,
Linus Walleij

[PATCH v9 04/10] pinctrl: check pinctrl ready for gpio range

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> pinctrl_get_device_gpio_range() only checks whether a certain GPIO pin
> is in gpio range. But maybe some GPIO pins don't have back-end pinctrl
> interface, it means that these pins are always configured as GPIO
> function. For example, gpio159 isn't related to back-end pinctrl device
> in Hi3620 while other GPIO pins are related to back-end pinctrl device.
>
> Append pinctrl_ready_for_gpio_range() that is used to check whether
> pinctrl device with GPIO range is ready. This function will be called
> after pinctrl_get_device_gpio_range() fails.
>
> If pinctrl device with GPIO range is found, it means that pinctrl device
> is already launched and a certain GPIO pin just don't have back-end pinctrl
> interface. Then pinctrl_request_gpio() shouldn't return -EPROBE_DEFER in
> this case.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Patch applied to the pinctrl tree for v3.10.

Thanks,
Linus Walleij

[PATCH v9 05/10] gpio: pl061: bind pinctrl by gpio request

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Add the pl061_gpio_request() to request pinctrl. Create the logic
> between pl061 gpio driver and pinctrl (pinctrl-single) driver.
>
> While a gpio pin is requested, it will request pinctrl driver to
> set that pin with gpio function mode. So pinctrl driver should
> append .gpio_request_enable() in pinmux_ops.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Patch applied to the pinctrl tree for v3.10.

Thanks,
Linus Walleij

[PATCH v9 06/10] pinctrl: single: create new gpio function range

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Since gpio driver could create gpio range in DTS, it could invoke
> pinctrl_request_gpio(). In the pinctrl-single driver, it needs to
> configure pins with gpio function mode.

Applied to the pinctrl tree for v3.10.

Thanks,
Linus Walleij

[PATCH v9 07/10] pinctrl: generic: dump pin configuration

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Add the support of dumping pin configuration.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Patch applied.

Yours,
Linus Walleij

[PATCH v9 08/10] pinctrl: single: set function mask as optional

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Since Hisilicon's pin controller is divided into two parts. One is the
> function mux, and the other is pin configuration. These two parts are
> in the different memory regions. So make pinctrl-single,function-mask
> as optional property. Then we can define pingroups without valid
> function mux that is only used for pin configuration.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> Acked-by: Tony Lindgren <tony@atomide.com>

Patch applied!

Thanks,
Linus Walleij

[PATCH v9 09/10] pinctrl: single: support generic pinconf

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> Support the operation of generic pinconf. The supported config arguments
> are INPUT_SCHMITT, INPUT_SCHMITT_ENABLE, DRIVE_STRENGHT, BIAS_DISABLE,
> BIAS_PULLUP, BIAS_PULLDOWN, SLEW_RATE.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
> Acked-by: Tony Lindgren <tony@atomide.com>

Patch applied!

Thanks,
Linus Walleij

[PATCH v9 10/10] document: devicetree: bind pinconf with pin single

[Linus Walleij]

On Sun, Feb 17, 2013 at 12:42 PM, Haojian Zhuang
<haojian.zhuang@linaro.org> wrote:

> From: Haojian Zhuang <haojian.zhuang@gmail.com>
>
> Add comments with pinconf & gpio range in the document of
> pinctrl-single.
>
> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
> Acked-by: Tony Lindgren <tony@atomide.com>

Patch applied!

Thanks,
Linus Walleij