[PATCH v4 0/8] Device Tree support for the at91sam9261ek

[jjhiblot@traphandler.com (Jean-Jacques Hiblot)]

Hi Greg,


2014-02-12 12:14 GMT+01:00 Gregory CLEMENT <gregory.clement@free-electrons.com>:
> Hi Jean-Jacques,
>
> On 12/02/2014 11:06, Jean-Jacques Hiblot wrote:
>> This patch set aims at bringing a device tree support for the sam9261.
>> It's mostly based on the sam9263 and sam9x5 stuff.
>>
>> Changes since V3:
>> * Added support for the touchscreen
>> * Added support for the spi dataflash
>> * Activated the TCB by default
>> * Reworked the patch organization to reduce the number of patchs
>> * changed the default bootargs (no mem description, UBI on mtdpart 5)
>> * Changed the xlate implementation of the at91 pinctrl driver to lock the GPIOs
>>   for IRQs instead of requesting them (needed for the touchscreen driver)
>> * some stylistic changes
>>
>> Changes since V2:
>> * removed the smc driver from the serie. It'll be posted in an independent
>>   serie later.
>> * removed the DM9000 support (it'll come with the smc driver)
>> * the sam9261 now supports the Common Clock Framework (CCF). Note: to enable
>>   the CCF you must remove from the kernel config the platforms that don't
>>   support it.
>> * Added basic DT binding for the bus matrix
>> * Added support for USB host
>> * Added support for USB gadget
>> * in dts(i), replaced interrupt-parent with interrupts-extended
>> * changed the nand partition plan (same as for the sama5d3)
>> * removed 'mem' parameter in command line
>> * re-ordered dt-nodes in ascending address order.
>> * split the lcd support patch in 2 parts (SOC and board)
>>
>>
>> Change since V1:
>> * changed the DT representation to use address translation and separate the
>>   timings' configuration from the device properties by adding a "simple-bus"
>>   inetrmediate node.
>> * moved the smc driver from drivers/bus to drivers/memmory
>> * smc driver now accepts timings in nanoseconds as well as raw register values
>> * smc driver can clip the timings if they're out of bound and dump them to the
>>   console
>> * DM9000 timings are now described in nanosecs (for the virtue of example)
>>
>> supported features are:
>> * working with the Common Clock Framework and the old at91 clock implementation
>> * dbgu
>> * lcdc
>> * usb host
>> * usb gadget,
>> * spi dataflash
>> * nand flash
>> * touchscreen
>> * leds
>> * user buttons
>>
>> In the TODO list:
>> * dm9000 (ethernet)
>> * audio
>> * mmc
>
>
> Besides the my comment on the 1st patch, all this series
> seems pretty neat for me.
thanks
>
> It's worth mentioning also that audio and mmc are in the
> TODO list by lack of hardware to test it. So what I suggest
actually the audio hardware is present but seems broken on my board.
Hopefully I should get another one to test this week.
> here is to send a follow-up patch set and to ask for a
> Tested-By from people being able to test it.
>
> For dm9000 the issue is (again) related to an ordering problem:
> the Ethernet need an interrupt provided by the gpio driver. Unfortunately,
> the gpio driver initialization is called after the dm900 driver
> initialization.
>
> Thanks,
>
> Gregory
>
>
>
>>
>> This serie relies on the following patchs:
>> usb: at91-udc: fix irq and iomem resource retrieval
>> ARM: at91: prepare sam9 dt boards transition to common
>>
>> Jean-Jacques
>>
>> Jean-Jacques Hiblot (8):
>>   at91: dt: Adds support for the bus matrix declaration in the DT
>>   at91: pinctrl: don't request GPIOs used for interrupts but lock them
>>     as IRQ
>>   at91: dt: Add at91sam9261 dt SoC support
>>   at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
>>   at91: dt: sam9261: Device Tree support for the at91sam9261ek
>>   at91: updated the at91_dt_defconfig with support for the ADS7846
>>   ARM: at91: prepare common clk transition for sam9261 SoC
>>   ARM: at91: move sam9261 SoC to common clk
>>
>>  arch/arm/boot/dts/Makefile          |   2 +
>>  arch/arm/boot/dts/at91sam9261.dtsi  | 740 ++++++++++++++++++++++++++++++++++++
>>  arch/arm/boot/dts/at91sam9261ek.dts | 204 ++++++++++
>>  arch/arm/configs/at91_dt_defconfig  |   2 +
>>  arch/arm/mach-at91/Kconfig          |   1 -
>>  arch/arm/mach-at91/at91sam9261.c    |  25 +-
>>  arch/arm/mach-at91/setup.c          |  23 ++
>>  drivers/pinctrl/pinctrl-at91.c      |   5 +-
>>  8 files changed, 996 insertions(+), 6 deletions(-)
>>  create mode 100644 arch/arm/boot/dts/at91sam9261.dtsi
>>  create mode 100644 arch/arm/boot/dts/at91sam9261ek.dts
>>
>
>
> --
> Gregory Clement, Free Electrons
> Kernel, drivers, real-time and embedded Linux
> development, consulting, training and support.
> http://free-electrons.com