[BISECTED] 3.10-rc1 OMAP1 GPIO IRQ regression

[grant.likely@secretlab.ca (Grant Likely)]

On Tue, Jun 25, 2013 at 8:04 AM, Tony Lindgren <tony@atomide.com> wrote:
> * Grant Likely <grant.likely@secretlab.ca> [130624 09:00]:
>> On Mon, Jun 24, 2013 at 8:21 AM, Tony Lindgren <tony@atomide.com> wrote:
>> > * Javier Martinez Canillas <martinez.javier@gmail.com> [130623 18:08]:
>> >> On Mon, Jun 24, 2013 at 1:43 AM, Aaro Koskinen <aaro.koskinen@iki.fi> wrote:
>> >> > Hi,
>> >> >
>> >> > On Mon, Jun 24, 2013 at 01:06:37AM +0200, Javier Martinez Canillas wrote:
>> >> >> On Mon, Jun 24, 2013 at 12:16 AM, Aaro Koskinen <aaro.koskinen@iki.fi> wrote:
>> >> >> > What is the status of this patch? We're already at 3.10-rc7 and GPIO
>> >> >> > IRQs are still broken on OMAP1.
>> >> >
>> >> > [...]
>> >> >
>> >> >> There is a problem with this patch.
>> >> >
>> >> > [...]
>> >> >
>> >> >> So I think that the correct solution is to add SPARSE_IRQ support to
>> >> >> omap1 and not reverting Jon's patch. Of course this may not be
>> >> >> possible since we are so close to 3.10 and most OMAP patches already
>> >> >> merged for 3.11 but we should definitely try to have this at least for
>> >> >> 3.12. Otherwise we won't be able to move to DT-only booting for
>> >> >> OMAP2+.
>> >> >
>> >> > OMAP1 does not use DT. So we could put this code under #ifdef
>> >> > CONFIG_ARCH_OMAP1 or similar. It's just a few lines of code. OMAP2+
>> >> > work should not regress OMAP1.
>> >> >
>> >> > Demanding SPARSE_IRQ support for OMAP1 should have been discussed before
>> >> > these changes were made. It's not reasonable to assume such things can
>> >> > be made during rc-cycle. Also, now, I don't think it's reasonable to
>> >> > wait for that to be done, as it would take until 3.12 or even later to
>> >> > get OMAP1 functional again.
>> >> >
>> >> > A.
>> >>
>> >> Hi,
>> >>
>> >> Yes, since we are so late in the -rc cycle and OMAP1 is currently
>> >> broken I agree that the only sensible solution is to revert the patch
>> >> for now.
>> >
>> > Agreed.
>> >
>> >> I just wanted to point out the issue that keeping the OMAP GPIO driver
>> >> using legacy mapping domain represents a blocker to have GPIO-IRQ
>> >> working with Device Tree for OMAP2+
>> >
>> > Yes. We can do the ifdef Aaro suggested, and let's also plan on
>> > converting omap1 to use SPARSE_IRQ. But with the ifdef we can cut
>> > away the dependency between these two.
>>
>> Alright. Sorry I dropped the ball on this one. I've lost track of
>> which patch needs to get applied, but given that it is so late in the
>> cycle, it would be better for someone else to apply the change, test
>> and send a pull request to Linus. I'm okay with it going through the
>> OMAP tree if that is the most expedient. Alternately, send me the pull
>> request and I'll pass it on to Linus.
>
> OK, I'll wait for Aaro's ack on Javier's patch and then put it into a
> branch for you.

Thanks Tony.

g.