* [PATCH 1/5] arm64: dts: qcom: Add RPM glink nodes to msm8996
2017-07-25 5:47 [PATCH 0/5] DB820c DTS dump Bjorn Andersson
@ 2017-07-25 5:47 ` Bjorn Andersson
2017-07-25 5:47 ` [PATCH 2/5] arm64: dts: qcom: db820c: Add pm8994 regulator node Bjorn Andersson
` (3 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 5:47 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 78 +++++++++++++++++++++++++++++++++++
1 file changed, 78 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 8f085716e258..8ebef05e1750 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -276,12 +276,83 @@
hwlocks = <&tcsr_mutex 3>;
};
+ rpm-glink {
+ compatible = "qcom,glink-rpm";
+
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+ mboxes = <&apcs_glb 0>;
+
+ rpm_requests {
+ compatible = "qcom,rpm-msm8996";
+ qcom,glink-channels = "rpm_requests";
+
+ pm8994-regulators {
+ compatible = "qcom,rpm-pm8994-regulators";
+
+ pm8994_s1: s1 {};
+ pm8994_s2: s2 {};
+ pm8994_s3: s3 {};
+ pm8994_s4: s4 {};
+ pm8994_s5: s5 {};
+ pm8994_s6: s6 {};
+ pm8994_s7: s7 {};
+ pm8994_s8: s8 {};
+ pm8994_s9: s9 {};
+ pm8994_s10: s10 {};
+ pm8994_s11: s11 {};
+ pm8994_s12: s12 {};
+
+ pm8994_l1: l1 {};
+ pm8994_l2: l2 {};
+ pm8994_l3: l3 {};
+ pm8994_l4: l4 {};
+ pm8994_l5: l5 {};
+ pm8994_l6: l6 {};
+ pm8994_l7: l7 {};
+ pm8994_l8: l8 {};
+ pm8994_l9: l9 {};
+ pm8994_l10: l10 {};
+ pm8994_l11: l11 {};
+ pm8994_l12: l12 {};
+ pm8994_l13: l13 {};
+ pm8994_l14: l14 {};
+ pm8994_l15: l15 {};
+ pm8994_l16: l16 {};
+ pm8994_l17: l17 {};
+ pm8994_l18: l18 {};
+ pm8994_l19: l19 {};
+ pm8994_l20: l20 {};
+ pm8994_l21: l21 {};
+ pm8994_l22: l22 {};
+ pm8994_l23: l23 {};
+ pm8994_l24: l24 {};
+ pm8994_l25: l25 {};
+ pm8994_l26: l26 {};
+ pm8994_l27: l27 {};
+ pm8994_l28: l28 {};
+ pm8994_l29: l29 {};
+ pm8994_l30: l30 {};
+ pm8994_l31: l31 {};
+ pm8994_l32: l32 {};
+ };
+
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
compatible = "simple-bus";
+ rpm_msg_ram: memory at 68000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x68000 0x6000>;
+ };
+
tcsr_mutex_regs: syscon at 740000 {
compatible = "syscon";
reg = <0x740000 0x20000>;
@@ -303,6 +374,13 @@
reg = <0x9820000 0x1000>;
};
+ apcs_glb: mailbox at 9820000 {
+ compatible = "qcom,msm8996-apcs-hmss-global";
+ reg = <0x9820000 0x1000>;
+
+ #mbox-cells = <1>;
+ };
+
gcc: clock-controller at 300000 {
compatible = "qcom,gcc-msm8996";
#clock-cells = <1>;
--
2.12.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 2/5] arm64: dts: qcom: db820c: Add pm8994 regulator node
2017-07-25 5:47 [PATCH 0/5] DB820c DTS dump Bjorn Andersson
2017-07-25 5:47 ` [PATCH 1/5] arm64: dts: qcom: Add RPM glink nodes to msm8996 Bjorn Andersson
@ 2017-07-25 5:47 ` Bjorn Andersson
2017-07-25 5:47 ` [PATCH 3/5] arm64: dts: msm8996: Add modem smp2p nodes Bjorn Andersson
` (2 subsequent siblings)
4 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 5:47 UTC (permalink / raw)
To: linux-arm-kernel
From: Rajendra Nayak <rnayak@codeaurora.org>
Add PM8994 RPM regulators with their min/max voltages to DB820c.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 148 +++++++++++++++++++++++++++
1 file changed, 148 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index d2196fc6d739..b4817d6c0d50 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -106,4 +106,152 @@
gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
};
};
+
+ rpm-glink {
+ rpm_requests {
+ pm8994-regulators {
+ vdd_l1-supply = <&pm8994_s3>;
+ vdd_l2_l26_l28-supply = <&pm8994_s3>;
+ vdd_l3_l11-supply = <&pm8994_s3>;
+ vdd_l4_l27_l31-supply = <&pm8994_s3>;
+ vdd_l5_l7-supply = <&pm8994_s5>;
+ vdd_l14_l15-supply = <&pm8994_s5>;
+ vdd_l20_l21-supply = <&pm8994_s5>;
+ vdd_l25-supply = <&pm8994_s3>;
+
+ s3 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+ s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ s5 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+ s7 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ l2 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ };
+ l3 {
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ };
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+ l6 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l11 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+ l17 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2900000>;
+ };
+ l19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ };
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ l22 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ l23 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+ l25 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+ l27 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ l28 {
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-allow-set-load;
+ };
+ l29 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ l30 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ l32 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+ };
};
--
2.12.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 3/5] arm64: dts: msm8996: Add modem smp2p nodes
2017-07-25 5:47 [PATCH 0/5] DB820c DTS dump Bjorn Andersson
2017-07-25 5:47 ` [PATCH 1/5] arm64: dts: qcom: Add RPM glink nodes to msm8996 Bjorn Andersson
2017-07-25 5:47 ` [PATCH 2/5] arm64: dts: qcom: db820c: Add pm8994 regulator node Bjorn Andersson
@ 2017-07-25 5:47 ` Bjorn Andersson
2017-07-25 17:29 ` Stephen Boyd
2017-07-25 5:47 ` [PATCH 4/5] arm64: dts: qcom: msm8996: Specify smd-edge for ADSP Bjorn Andersson
2017-07-25 5:47 ` [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node Bjorn Andersson
4 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 5:47 UTC (permalink / raw)
To: linux-arm-kernel
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 8ebef05e1750..7d909546ca24 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -662,6 +662,30 @@
};
};
+ modem-smp2p {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <0 451 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 16 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ modem_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ modem_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
smp2p-slpi {
compatible = "qcom,smp2p";
qcom,smem = <481>, <430>;
--
2.12.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 3/5] arm64: dts: msm8996: Add modem smp2p nodes
2017-07-25 5:47 ` [PATCH 3/5] arm64: dts: msm8996: Add modem smp2p nodes Bjorn Andersson
@ 2017-07-25 17:29 ` Stephen Boyd
0 siblings, 0 replies; 10+ messages in thread
From: Stephen Boyd @ 2017-07-25 17:29 UTC (permalink / raw)
To: linux-arm-kernel
On 07/24/2017 10:47 PM, Bjorn Andersson wrote:
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/msm8996.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index 8ebef05e1750..7d909546ca24 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -662,6 +662,30 @@
> };
> };
>
> + modem-smp2p {
> + compatible = "qcom,smp2p";
> + qcom,smem = <435>, <428>;
> +
> + interrupts = <0 451 IRQ_TYPE_EDGE_RISING>;
s/0/GIC_SPI/?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 4/5] arm64: dts: qcom: msm8996: Specify smd-edge for ADSP
2017-07-25 5:47 [PATCH 0/5] DB820c DTS dump Bjorn Andersson
` (2 preceding siblings ...)
2017-07-25 5:47 ` [PATCH 3/5] arm64: dts: msm8996: Add modem smp2p nodes Bjorn Andersson
@ 2017-07-25 5:47 ` Bjorn Andersson
2017-07-25 5:47 ` [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node Bjorn Andersson
4 siblings, 0 replies; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 5:47 UTC (permalink / raw)
To: linux-arm-kernel
Add the smd-edge node for the adsp, to allow SMD communication with the
ADSP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 7d909546ca24..395666dcce1b 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -636,6 +636,15 @@
qcom,smem-states = <&adsp_smp2p_out 0>;
qcom,smem-state-names = "stop";
+
+ smd-edge {
+ interrupts = <0 156 IRQ_TYPE_EDGE_RISING>;
+
+ label = "lpass";
+ qcom,ipc = <&apcs 16 8>;
+ qcom,smd-edge = <1>;
+ qcom,remote-pid = <2>;
+ };
};
adsp-smp2p {
--
2.12.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node
2017-07-25 5:47 [PATCH 0/5] DB820c DTS dump Bjorn Andersson
` (3 preceding siblings ...)
2017-07-25 5:47 ` [PATCH 4/5] arm64: dts: qcom: msm8996: Specify smd-edge for ADSP Bjorn Andersson
@ 2017-07-25 5:47 ` Bjorn Andersson
2017-07-25 6:09 ` Vivek Gautam
4 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 5:47 UTC (permalink / raw)
To: linux-arm-kernel
From: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 395666dcce1b..d0865d2f731e 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -496,6 +496,17 @@
status = "disabled";
};
+ qfprom: qfprom at 74000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00074000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ qusb2p_hstx_trim: hstx_trim at 24e {
+ reg = <0x24e 0x2>;
+ bits = <5 4>;
+ };
+ };
+
sdhc2: sdhci at 74a4900 {
status = "disabled";
compatible = "qcom,sdhci-msm-v4";
--
2.12.0
^ permalink raw reply related [flat|nested] 10+ messages in thread* [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node
2017-07-25 5:47 ` [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node Bjorn Andersson
@ 2017-07-25 6:09 ` Vivek Gautam
2017-07-25 6:30 ` Bjorn Andersson
0 siblings, 1 reply; 10+ messages in thread
From: Vivek Gautam @ 2017-07-25 6:09 UTC (permalink / raw)
To: linux-arm-kernel
Hi Bjorn,
On Tue, Jul 25, 2017 at 11:17 AM, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
> From: Vivek Gautam <vivek.gautam@codeaurora.org>
>
> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/msm8996.dtsi | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index 395666dcce1b..d0865d2f731e 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -496,6 +496,17 @@
> status = "disabled";
> };
>
> + qfprom: qfprom at 74000 {
> + compatible = "qcom,qfprom";
> + reg = <0x00074000 0x8ff>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + qusb2p_hstx_trim: hstx_trim at 24e {
> + reg = <0x24e 0x2>;
> + bits = <5 4>;
> + };
There's one more part to it which will be used by the secondary
USB2 controller.
I was hoping to add this patch along with the USB device tree patches.
Let me know if you are not using this patch for anything now, i can
submit it along with the usb series.
Regards
Vivek
> + };
> +
> sdhc2: sdhci at 74a4900 {
> status = "disabled";
> compatible = "qcom,sdhci-msm-v4";
> --
> 2.12.0
>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node
2017-07-25 6:09 ` Vivek Gautam
@ 2017-07-25 6:30 ` Bjorn Andersson
2017-07-25 8:12 ` Vivek Gautam
0 siblings, 1 reply; 10+ messages in thread
From: Bjorn Andersson @ 2017-07-25 6:30 UTC (permalink / raw)
To: linux-arm-kernel
On Mon 24 Jul 23:09 PDT 2017, Vivek Gautam wrote:
> Hi Bjorn,
>
>
> On Tue, Jul 25, 2017 at 11:17 AM, Bjorn Andersson
> <bjorn.andersson@linaro.org> wrote:
> > From: Vivek Gautam <vivek.gautam@codeaurora.org>
> >
> > Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > ---
> > arch/arm64/boot/dts/qcom/msm8996.dtsi | 11 +++++++++++
> > 1 file changed, 11 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> > index 395666dcce1b..d0865d2f731e 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> > @@ -496,6 +496,17 @@
> > status = "disabled";
> > };
> >
> > + qfprom: qfprom at 74000 {
> > + compatible = "qcom,qfprom";
> > + reg = <0x00074000 0x8ff>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + qusb2p_hstx_trim: hstx_trim at 24e {
> > + reg = <0x24e 0x2>;
> > + bits = <5 4>;
> > + };
>
> There's one more part to it which will be used by the secondary
> USB2 controller.
> I was hoping to add this patch along with the USB device tree patches.
> Let me know if you are not using this patch for anything now, i can
> submit it along with the usb series.
>
I omitted this due to the rpmcc dependency. But I must have looked at
the wrong node, as there is no such dependency.
So this should be replaced by the full 0387312d9f35 ("arm64: dts:
msm8996: Add device node for qcom qusb2 phy"), which has a commit
message as well.
Thanks for spotting my mistake.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH 5/5] arm64: dts: msm8996: Add QFPROM node
2017-07-25 6:30 ` Bjorn Andersson
@ 2017-07-25 8:12 ` Vivek Gautam
0 siblings, 0 replies; 10+ messages in thread
From: Vivek Gautam @ 2017-07-25 8:12 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Jul 25, 2017 at 12:00 PM, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
> On Mon 24 Jul 23:09 PDT 2017, Vivek Gautam wrote:
>
>> Hi Bjorn,
>>
>>
>> On Tue, Jul 25, 2017 at 11:17 AM, Bjorn Andersson
>> <bjorn.andersson@linaro.org> wrote:
>> > From: Vivek Gautam <vivek.gautam@codeaurora.org>
>> >
>> > Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>> > ---
>> > arch/arm64/boot/dts/qcom/msm8996.dtsi | 11 +++++++++++
>> > 1 file changed, 11 insertions(+)
>> >
>> > diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
>> > index 395666dcce1b..d0865d2f731e 100644
>> > --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
>> > +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
>> > @@ -496,6 +496,17 @@
>> > status = "disabled";
>> > };
>> >
>> > + qfprom: qfprom at 74000 {
>> > + compatible = "qcom,qfprom";
>> > + reg = <0x00074000 0x8ff>;
>> > + #address-cells = <1>;
>> > + #size-cells = <1>;
>> > + qusb2p_hstx_trim: hstx_trim at 24e {
>> > + reg = <0x24e 0x2>;
>> > + bits = <5 4>;
>> > + };
>>
>> There's one more part to it which will be used by the secondary
>> USB2 controller.
>> I was hoping to add this patch along with the USB device tree patches.
>> Let me know if you are not using this patch for anything now, i can
>> submit it along with the usb series.
>>
>
> I omitted this due to the rpmcc dependency. But I must have looked at
> the wrong node, as there is no such dependency.
>
> So this should be replaced by the full 0387312d9f35 ("arm64: dts:
> msm8996: Add device node for qcom qusb2 phy"), which has a commit
> message as well.
>
>
> Thanks for spotting my mistake.
Thanks Bjorn. I will prepare and post out these patches soon.
Best Regards
Vivek
>
> Regards,
> Bjorn
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 10+ messages in thread