[PATCHv3 5/5] ARM: sunxi: dts: Add note ps2 pins conflict with hdmi

[wens@csie.org (Chen-Yu Tsai)]

Hi,

On Sat, Dec 13, 2014 at 11:18 AM, Vishnu Patekar
<vishnupatekar0510@gmail.com> wrote:
> Hello Chen-Yu,
> Thank you for pointing out styling error.
>
> On Sat, Dec 13, 2014 at 7:36 AM, Chen-Yu Tsai <wens@csie.org> wrote:
>>
>> Hi,
>>
>> On Sat, Dec 13, 2014 at 2:25 AM, VishnuPatekar
>> <vishnupatekar0510@gmail.com> wrote:
>> > 1. Please note that ps20 pins conflict with HDMI on Lime2 Board
>> > so, by deault ps20 and ps21 are disabled for Lime2 Board.
>> > There is no on board ps2 connector and these pins can be used
>> > for different purpose.
>> >
>> > Signed-off-by: VishnuPatekar <vishnupatekar0510@gmail.com>
>> > ---
>> >  arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts |    6 +++++-
>> >  1 file changed, 5 insertions(+), 1 deletion(-)
>> >
>> > diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> > b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> > index ed364d5..951b615 100644
>> > --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> > +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> > @@ -112,7 +112,11 @@
>> >                         pinctrl-0 = <&uart0_pins_a>;
>> >                         status = "okay";
>> >                 };
>> > -
>> > +
>> > +               /* PS2 0 and PS2 1 are disabled by default; Please note
>> > that
>> > +               ps20 pins conflict with HDMI on Lime2 Board
>> > +               */
>> > +
>>
>> Multi-line comments should be:
>>
>> /*
>>  * line 1
>>  * line 2
>>  * ...
>>  */
>
> Okie.

So, in fact this patch shouldnt be needed. The LIME2 uses the dedicated
pins for HDMI DDC. PS2 0 pins PI20 and PI21 are in fact routed to
the GPIO-2 header. They are _not_ used for HDMI. Nothing bad should
happen unless you also multiplex PI20/PI21 to HSCL/HDSA.

If you check the schematics Olimex published and trace the HDMI lines,
you will see that this is the case.

ChenYu

>>
>>
>> And why is there a delete and insert for an empty line?
>> Weird... though git seems to ignore it when applying.
>
> I used clean_patch to clear the styling error. that might have modified it.
>
>
>>
>>
>> ChenYu
>>
>> >                 i2c0: i2c at 01c2ac00 {
>> >                         pinctrl-names = "default";
>> >                         pinctrl-0 = <&i2c0_pins_a>;
>> > --
>> > 1.7.9.5
>> >
>> >
>> > _______________________________________________
>> > linux-arm-kernel mailing list
>> > linux-arm-kernel at lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel