[PATCH v6 00/11] KVM: arm64: PMU: Allow userspace to limit the number of PMCs on vCPU

[PATCH v6 00/11] KVM: arm64: PMU: Allow userspace to limit the number of PMCs on vCPU

[Raghavendra Rao Ananta]

Hello,

With permission from Reiji Watanabe <reijiw@google.com>, the original
author of the series, I'm posting the v6 with necessary alterations.

The goal of this series is to allow userspace to limit the number
of PMU event counters on the vCPU.  We need this to support migration
across systems that implement different numbers of counters.

The number of PMU event counters is indicated in PMCR_EL0.N.
For a vCPU with PMUv3 configured, its value will be the same as
the current PE by default.  Userspace can set PMCR_EL0.N for the
vCPU to any value even with the current KVM using KVM_SET_ONE_REG.
However, it is practically unsupported, as KVM resets PMCR_EL0.N
to the host value on vCPU reset and some KVM code uses the host
value to identify (un)implemented event counters on the vCPU.

This series will ensure that the PMCR_EL0.N value is preserved
on vCPU reset and that KVM doesn't use the host value
to identify (un)implemented event counters on the vCPU.
This allows userspace to limit the number of the PMU event
counters on the vCPU.

The series is based on v6.6-rc3.

Patch 1 adds helper functions to set a PMU for the guest. This
helper will make it easier for the following patches to add
modify codes for that process.

Patch 2 makes the default PMU for the guest set on the first
vCPU reset.

Patch 3 fixes reset_pmu_reg() to ensure that (RAZ) bits of
PMCNTEN{SET,CLR}_EL0, PMINTEN{SET,CLR}_EL1, and
PMOVS{SET,CLR}_EL1 corresponding to unimplemented event
counters on the vCPU are reset to zero.

Patch 4 is a minor refactoring to use the default PMU register reset
function for PMUSERENR_EL0 and PMCCFILTR_EL0.

Patch 5 adds a helper to read vCPU's PMCR_EL0.

Patch 6 changes the code to use the guest's PMCR_EL0.N, instead
of the PE's PMCR_EL0.N.

Patch 7 adds support userspace modifying PMCR_EL0.N.

Patch 8-11 adds a selftest to verify reading and writing PMU registers
for implemented or unimplemented PMU event counters on the vCPU.

v6: Thanks, Oliver and Shaoqin for the suggestions
- Split the previously defined kvm_arm_set_vm_pmu() into separate
  functions: default arm_pmu and a caller requested arm_pmu.
- Send -EINVAL from kvm_reset_vcpu(), instead of -ENODEV for the
  case where KVM fails to set a default arm_pmu, to remain consistent
  with the existing behavior.
- Drop the v5 patch-5/12 that removes ARMV8_PMU_PMCR_N_MASK and adds
  ARMV8_PMU_PMCR_N. Make corresponding changes to v5 patch-6/12.
- Disregard introducing 'pmcr_n_limit' in kvm->arch as a member to
  be accessed later in 'set_pmcr()'. Instead, directly obtain the
  value by accessing the saved 'arm_pmu'.
- 'set_pmcr()' ignores the error when userspace tries to set PMCR.N
  greater than the hardware limit to keep the existing API behavior.
- 'set_pmcr()' ignores modifications to the register after the VM has
  started and returns a success to userspace.
- Introduce [get|set]_pmcr_n() helpers in the selftest to make
  modifications to the field easier.
- Define the 'vpmu_vm' globally in the selftest, instead of allocating
  it every time a VM is created.
- Use the new printf style __GUEST_ASSERT()s in the selftest. 

v5:
https://lore.kernel.org/all/20230817003029.3073210-1-rananta@google.com/
 - Drop the patches (v4 3,4) related to PMU version fixes as it's
   now being handled in a separate series [1].
 - Switch to config_lock, instead of kvm->lock, while configuring
   the guest PMU.
 - Instead of continuing after a WARN_ON() for the return value of
   kvm_arm_set_vm_pmu() in kvm_arm_pmu_v3_set_pmu(), patch-1 now
   returns from the function immediately with the error code.
 - Fix WARN_ON() logic in kvm_host_pmu_init() (patch v4 9/14).
 - Instead of returning 0, return -ENODEV from the
   kvm_arm_set_vm_pmu() stub function.
 - Do not define the PMEVN_CASE() and PMEVN_SWITCH() macros in
   the selftest code as they are now included in the imported
   arm_pmuv3.h header.
 - Since the (initial) purpose of the selftest is to test the
   accessibility of the counter registers, remove the functional
   test at the end of test_access_pmc_regs(). It'll be added
   later in a separate series.
 - Introduce additional helper functions (destroy_vpmu_vm(),
   PMC_ACC_TO_IDX()) in the selftest for ease of maintenance
   and debugging.
   
v4:
https://lore.kernel.org/all/20230211031506.4159098-1-reijiw@google.com/
 - Fix the selftest bug in patch 13 (Have test_access_pmc_regs() to
   specify pmc index for test_bitmap_pmu_regs() instead of bit-shifted
   value (Thank you Raghavendra for the reporting the issue!).

v3:
https://lore.kernel.org/all/20230203040242.1792453-1-reijiw@google.com/
 - Remove reset_pmu_reg(), and use reset_val() instead. [Marc]
 - Fixed the initial value of PMCR_EL0.N on heterogeneous
   PMU systems. [Oliver]
 - Fixed PMUVer issues on heterogeneous PMU systems.
 - Fixed typos [Shaoqin]

v2:
https://lore.kernel.org/all/20230117013542.371944-1-reijiw@google.com/
 - Added the sys_reg's set_user() handler for the PMCR_EL0 to
   disallow userspace to set PMCR_EL0.N for the vCPU to a value
   that is greater than the host value (and added a new test
   case for this behavior). [Oliver]
 - Added to the commit log of the patch 2 that PMUSERENR_EL0 and
   PMCCFILTR_EL0 have UNKNOWN reset values.

v1:
https://lore.kernel.org/all/20221230035928.3423990-1-reijiw@google.com/

Thank you.
Raghavendra

[1]:
https://lore.kernel.org/all/20230728181907.1759513-1-reijiw@google.com/

Raghavendra Rao Ananta (1):
  tools: Import arm_pmuv3.h

Reiji Watanabe (10):
  KVM: arm64: PMU: Introduce helpers to set the guest's PMU
  KVM: arm64: PMU: Set the default PMU for the guest on vCPU reset
  KVM: arm64: PMU: Clear PM{C,I}NTEN{SET,CLR} and PMOVS{SET,CLR} on vCPU
    reset
  KVM: arm64: PMU: Don't define the sysreg reset() for
    PM{USERENR,CCFILTR}_EL0
  KVM: arm64: PMU: Add a helper to read a vCPU's PMCR_EL0
  KVM: arm64: PMU: Set PMCR_EL0.N for vCPU based on the associated PMU
  KVM: arm64: PMU: Allow userspace to limit PMCR_EL0.N for the guest
  KVM: selftests: aarch64: Introduce vpmu_counter_access test
  KVM: selftests: aarch64: vPMU register test for implemented counters
  KVM: selftests: aarch64: vPMU register test for unimplemented counters

 arch/arm64/include/asm/kvm_host.h             |   3 +
 arch/arm64/kvm/arm.c                          |   3 +-
 arch/arm64/kvm/pmu-emul.c                     |  91 ++-
 arch/arm64/kvm/reset.c                        |  18 +-
 arch/arm64/kvm/sys_regs.c                     | 102 ++-
 include/kvm/arm_pmu.h                         |  12 +
 tools/include/perf/arm_pmuv3.h                | 308 +++++++++
 tools/testing/selftests/kvm/Makefile          |   1 +
 .../kvm/aarch64/vpmu_counter_access.c         | 590 ++++++++++++++++++
 .../selftests/kvm/include/aarch64/processor.h |   1 +
 10 files changed, 1064 insertions(+), 65 deletions(-)
 create mode 100644 tools/include/perf/arm_pmuv3.h
 create mode 100644 tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c


base-commit: 6465e260f48790807eef06b583b38ca9789b6072
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 01/11] KVM: arm64: PMU: Introduce helpers to set the guest's PMU

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

Introduce new helper functions to set the guest's PMU
(kvm->arch.arm_pmu) either to a default probed instance or to a
caller requested one, and use it when the guest's PMU needs to
be set. These helpers will make it easier for the following
patches to modify the relevant code.

No functional change intended.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/pmu-emul.c | 50 +++++++++++++++++++++++++++------------
 1 file changed, 35 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/kvm/pmu-emul.c b/arch/arm64/kvm/pmu-emul.c
index 6b066e04dc5df..fb9817bdfeb57 100644
--- a/arch/arm64/kvm/pmu-emul.c
+++ b/arch/arm64/kvm/pmu-emul.c
@@ -874,6 +874,36 @@ static bool pmu_irq_is_valid(struct kvm *kvm, int irq)
 	return true;
 }
 
+static void kvm_arm_set_pmu(struct kvm *kvm, struct arm_pmu *arm_pmu)
+{
+	lockdep_assert_held(&kvm->arch.config_lock);
+
+	kvm->arch.arm_pmu = arm_pmu;
+}
+
+/**
+ * kvm_arm_set_default_pmu - No PMU set, get the default one.
+ * @kvm: The kvm pointer
+ *
+ * The observant among you will notice that the supported_cpus
+ * mask does not get updated for the default PMU even though it
+ * is quite possible the selected instance supports only a
+ * subset of cores in the system. This is intentional, and
+ * upholds the preexisting behavior on heterogeneous systems
+ * where vCPUs can be scheduled on any core but the guest
+ * counters could stop working.
+ */
+static int kvm_arm_set_default_pmu(struct kvm *kvm)
+{
+	struct arm_pmu *arm_pmu = kvm_pmu_probe_armpmu();
+
+	if (!arm_pmu)
+		return -ENODEV;
+
+	kvm_arm_set_pmu(kvm, arm_pmu);
+	return 0;
+}
+
 static int kvm_arm_pmu_v3_set_pmu(struct kvm_vcpu *vcpu, int pmu_id)
 {
 	struct kvm *kvm = vcpu->kvm;
@@ -893,7 +923,7 @@ static int kvm_arm_pmu_v3_set_pmu(struct kvm_vcpu *vcpu, int pmu_id)
 				break;
 			}
 
-			kvm->arch.arm_pmu = arm_pmu;
+			kvm_arm_set_pmu(kvm, arm_pmu);
 			cpumask_copy(kvm->arch.supported_cpus, &arm_pmu->supported_cpus);
 			ret = 0;
 			break;
@@ -917,20 +947,10 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 		return -EBUSY;
 
 	if (!kvm->arch.arm_pmu) {
-		/*
-		 * No PMU set, get the default one.
-		 *
-		 * The observant among you will notice that the supported_cpus
-		 * mask does not get updated for the default PMU even though it
-		 * is quite possible the selected instance supports only a
-		 * subset of cores in the system. This is intentional, and
-		 * upholds the preexisting behavior on heterogeneous systems
-		 * where vCPUs can be scheduled on any core but the guest
-		 * counters could stop working.
-		 */
-		kvm->arch.arm_pmu = kvm_pmu_probe_armpmu();
-		if (!kvm->arch.arm_pmu)
-			return -ENODEV;
+		int ret = kvm_arm_set_default_pmu(kvm);
+
+		if (ret)
+			return ret;
 	}
 
 	switch (attr->attr) {
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 02/11] KVM: arm64: PMU: Set the default PMU for the guest on vCPU reset

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

The following patches will use the number of counters information
from the arm_pmu and use this to set the PMCR.N for the guest
during vCPU reset. However, since the guest is not associated
with any arm_pmu until userspace configures the vPMU device
attributes, and a reset can happen before this event, call
kvm_arm_support_pmu_v3() just before doing the reset.

No functional change intended.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/pmu-emul.c | 12 ++----------
 arch/arm64/kvm/reset.c    | 18 +++++++++++++-----
 include/kvm/arm_pmu.h     |  6 ++++++
 3 files changed, 21 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/kvm/pmu-emul.c b/arch/arm64/kvm/pmu-emul.c
index fb9817bdfeb57..998e1bbd5310d 100644
--- a/arch/arm64/kvm/pmu-emul.c
+++ b/arch/arm64/kvm/pmu-emul.c
@@ -717,8 +717,7 @@ static struct arm_pmu *kvm_pmu_probe_armpmu(void)
 	 * It is still necessary to get a valid cpu, though, to probe for the
 	 * default PMU instance as userspace is not required to specify a PMU
 	 * type. In order to uphold the preexisting behavior KVM selects the
-	 * PMU instance for the core where the first call to the
-	 * KVM_ARM_VCPU_PMU_V3_CTRL attribute group occurs. A dependent use case
+	 * PMU instance for the core during the vcpu reset. A dependent use case
 	 * would be a user with disdain of all things big.LITTLE that affines
 	 * the VMM to a particular cluster of cores.
 	 *
@@ -893,7 +892,7 @@ static void kvm_arm_set_pmu(struct kvm *kvm, struct arm_pmu *arm_pmu)
  * where vCPUs can be scheduled on any core but the guest
  * counters could stop working.
  */
-static int kvm_arm_set_default_pmu(struct kvm *kvm)
+int kvm_arm_set_default_pmu(struct kvm *kvm)
 {
 	struct arm_pmu *arm_pmu = kvm_pmu_probe_armpmu();
 
@@ -946,13 +945,6 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 	if (vcpu->arch.pmu.created)
 		return -EBUSY;
 
-	if (!kvm->arch.arm_pmu) {
-		int ret = kvm_arm_set_default_pmu(kvm);
-
-		if (ret)
-			return ret;
-	}
-
 	switch (attr->attr) {
 	case KVM_ARM_VCPU_PMU_V3_IRQ: {
 		int __user *uaddr = (int __user *)(long)attr->addr;
diff --git a/arch/arm64/kvm/reset.c b/arch/arm64/kvm/reset.c
index 7a65a35ee4ac4..6912832b44b6d 100644
--- a/arch/arm64/kvm/reset.c
+++ b/arch/arm64/kvm/reset.c
@@ -206,6 +206,7 @@ static int kvm_vcpu_enable_ptrauth(struct kvm_vcpu *vcpu)
  */
 int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 {
+	struct kvm *kvm = vcpu->kvm;
 	struct vcpu_reset_state reset_state;
 	int ret;
 	bool loaded;
@@ -216,6 +217,18 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 	vcpu->arch.reset_state.reset = false;
 	spin_unlock(&vcpu->arch.mp_state_lock);
 
+	if (kvm_vcpu_has_pmu(vcpu)) {
+		if (!kvm_arm_support_pmu_v3())
+			return -EINVAL;
+
+		/*
+		 * When the vCPU has a PMU, but no PMU is set for the guest
+		 * yet, set the default one.
+		 */
+		if (unlikely(!kvm->arch.arm_pmu) && kvm_arm_set_default_pmu(kvm))
+			return -EINVAL;
+	}
+
 	/* Reset PMU outside of the non-preemptible section */
 	kvm_pmu_vcpu_reset(vcpu);
 
@@ -255,11 +268,6 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 	else
 		pstate = VCPU_RESET_PSTATE_EL1;
 
-	if (kvm_vcpu_has_pmu(vcpu) && !kvm_arm_support_pmu_v3()) {
-		ret = -EINVAL;
-		goto out;
-	}
-
 	/* Reset core registers */
 	memset(vcpu_gp_regs(vcpu), 0, sizeof(*vcpu_gp_regs(vcpu)));
 	memset(&vcpu->arch.ctxt.fp_regs, 0, sizeof(vcpu->arch.ctxt.fp_regs));
diff --git a/include/kvm/arm_pmu.h b/include/kvm/arm_pmu.h
index 31029f4f7be85..b80c75d80886b 100644
--- a/include/kvm/arm_pmu.h
+++ b/include/kvm/arm_pmu.h
@@ -101,6 +101,7 @@ void kvm_vcpu_pmu_resync_el0(void);
 })
 
 u8 kvm_arm_pmu_get_pmuver_limit(void);
+int kvm_arm_set_default_pmu(struct kvm *kvm);
 
 #else
 struct kvm_pmu {
@@ -174,6 +175,11 @@ static inline u8 kvm_arm_pmu_get_pmuver_limit(void)
 }
 static inline void kvm_vcpu_pmu_resync_el0(void) {}
 
+static inline int kvm_arm_set_default_pmu(struct kvm *kvm)
+{
+	return -ENODEV;
+}
+
 #endif
 
 #endif
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 03/11] KVM: arm64: PMU: Clear PM{C,I}NTEN{SET,CLR} and PMOVS{SET,CLR} on vCPU reset

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

On vCPU reset, PMCNTEN{SET,CLR}_EL0, PMINTEN{SET,CLR}_EL1, and
PMOVS{SET,CLR}_EL1 for a vCPU are reset by reset_pmu_reg().
This function clears RAZ bits of those registers corresponding
to unimplemented event counters on the vCPU, and sets bits
corresponding to implemented event counters to a predefined
pseudo UNKNOWN value (some bits are set to 1).

The function identifies (un)implemented event counters on the
vCPU based on the PMCR_EL0.N value on the host. Using the host
value for this would be problematic when KVM supports letting
userspace set PMCR_EL0.N to a value different from the host value
(some of the RAZ bits of those registers could end up being set to 1).

Fix this by clearing the registers so that it can ensure
that all the RAZ bits are cleared even when the PMCR_EL0.N value
for the vCPU is different from the host value. Use reset_val() to
do this instead of fixing reset_pmu_reg(), and remove
reset_pmu_reg(), as it is no longer used.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/sys_regs.c | 21 +--------------------
 1 file changed, 1 insertion(+), 20 deletions(-)

diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index e92ec810d4494..ffd123fae30d6 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -717,25 +717,6 @@ static unsigned int pmu_visibility(const struct kvm_vcpu *vcpu,
 	return REG_HIDDEN;
 }
 
-static u64 reset_pmu_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r)
-{
-	u64 n, mask = BIT(ARMV8_PMU_CYCLE_IDX);
-
-	/* No PMU available, any PMU reg may UNDEF... */
-	if (!kvm_arm_support_pmu_v3())
-		return 0;
-
-	n = read_sysreg(pmcr_el0) >> ARMV8_PMU_PMCR_N_SHIFT;
-	n &= ARMV8_PMU_PMCR_N_MASK;
-	if (n)
-		mask |= GENMASK(n - 1, 0);
-
-	reset_unknown(vcpu, r);
-	__vcpu_sys_reg(vcpu, r->reg) &= mask;
-
-	return __vcpu_sys_reg(vcpu, r->reg);
-}
-
 static u64 reset_pmevcntr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r)
 {
 	reset_unknown(vcpu, r);
@@ -1115,7 +1096,7 @@ static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
 	  trap_wcr, reset_wcr, 0, 0,  get_wcr, set_wcr }
 
 #define PMU_SYS_REG(name)						\
-	SYS_DESC(SYS_##name), .reset = reset_pmu_reg,			\
+	SYS_DESC(SYS_##name), .reset = reset_val,			\
 	.visibility = pmu_visibility
 
 /* Macro to expand the PMEVCNTRn_EL0 register */
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 04/11] KVM: arm64: PMU: Don't define the sysreg reset() for PM{USERENR,CCFILTR}_EL0

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

The default reset function for PMU registers (defined by PMU_SYS_REG)
now simply clears a specified register. Use the default one for
PMUSERENR_EL0 and PMCCFILTR_EL0, as KVM currently clears those
registers on vCPU reset (NOTE: All non-RES0 fields of those
registers have UNKNOWN reset values, and the same fields of
their AArch32 registers have 0 reset values).

No functional change intended.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/sys_regs.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index ffd123fae30d6..66b9e1de54230 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -2180,7 +2180,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	 * in 32bit mode. Here we choose to reset it as zero for consistency.
 	 */
 	{ PMU_SYS_REG(PMUSERENR_EL0), .access = access_pmuserenr,
-	  .reset = reset_val, .reg = PMUSERENR_EL0, .val = 0 },
+	  .reg = PMUSERENR_EL0, },
 	{ PMU_SYS_REG(PMOVSSET_EL0),
 	  .access = access_pmovs, .reg = PMOVSSET_EL0 },
 
@@ -2338,7 +2338,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	 * in 32bit mode. Here we choose to reset it as zero for consistency.
 	 */
 	{ PMU_SYS_REG(PMCCFILTR_EL0), .access = access_pmu_evtyper,
-	  .reset = reset_val, .reg = PMCCFILTR_EL0, .val = 0 },
+	  .reg = PMCCFILTR_EL0, },
 
 	EL2_REG(VPIDR_EL2, access_rw, reset_unknown, 0),
 	EL2_REG(VMPIDR_EL2, access_rw, reset_unknown, 0),
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 05/11] KVM: arm64: PMU: Add a helper to read a vCPU's PMCR_EL0

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

Add a helper to read a vCPU's PMCR_EL0, and use it when KVM
reads a vCPU's PMCR_EL0.

The PMCR_EL0 value is tracked by a sysreg file per each vCPU.
The following patches will make (only) PMCR_EL0.N track per guest.
Having the new helper will be useful to combine the PMCR_EL0.N
field (tracked per guest) and the other fields (tracked per vCPU)
to provide the value of PMCR_EL0.

No functional change intended.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/arm.c      |  3 +--
 arch/arm64/kvm/pmu-emul.c | 21 +++++++++++++++------
 arch/arm64/kvm/sys_regs.c |  6 +++---
 include/kvm/arm_pmu.h     |  6 ++++++
 4 files changed, 25 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/kvm/arm.c b/arch/arm64/kvm/arm.c
index 4866b3f7b4ea3..86cafe5a6010b 100644
--- a/arch/arm64/kvm/arm.c
+++ b/arch/arm64/kvm/arm.c
@@ -801,8 +801,7 @@ static int check_vcpu_requests(struct kvm_vcpu *vcpu)
 		}
 
 		if (kvm_check_request(KVM_REQ_RELOAD_PMU, vcpu))
-			kvm_pmu_handle_pmcr(vcpu,
-					    __vcpu_sys_reg(vcpu, PMCR_EL0));
+			kvm_pmu_handle_pmcr(vcpu, kvm_vcpu_read_pmcr(vcpu));
 
 		if (kvm_check_request(KVM_REQ_RESYNC_PMU_EL0, vcpu))
 			kvm_vcpu_pmu_restore_guest(vcpu);
diff --git a/arch/arm64/kvm/pmu-emul.c b/arch/arm64/kvm/pmu-emul.c
index 998e1bbd5310d..d89438956f7d3 100644
--- a/arch/arm64/kvm/pmu-emul.c
+++ b/arch/arm64/kvm/pmu-emul.c
@@ -72,7 +72,7 @@ static bool kvm_pmc_is_64bit(struct kvm_pmc *pmc)
 
 static bool kvm_pmc_has_64bit_overflow(struct kvm_pmc *pmc)
 {
-	u64 val = __vcpu_sys_reg(kvm_pmc_to_vcpu(pmc), PMCR_EL0);
+	u64 val = kvm_vcpu_read_pmcr(kvm_pmc_to_vcpu(pmc));
 
 	return (pmc->idx < ARMV8_PMU_CYCLE_IDX && (val & ARMV8_PMU_PMCR_LP)) ||
 	       (pmc->idx == ARMV8_PMU_CYCLE_IDX && (val & ARMV8_PMU_PMCR_LC));
@@ -250,7 +250,7 @@ void kvm_pmu_vcpu_destroy(struct kvm_vcpu *vcpu)
 
 u64 kvm_pmu_valid_counter_mask(struct kvm_vcpu *vcpu)
 {
-	u64 val = __vcpu_sys_reg(vcpu, PMCR_EL0) >> ARMV8_PMU_PMCR_N_SHIFT;
+	u64 val = kvm_vcpu_read_pmcr(vcpu) >> ARMV8_PMU_PMCR_N_SHIFT;
 
 	val &= ARMV8_PMU_PMCR_N_MASK;
 	if (val == 0)
@@ -272,7 +272,7 @@ void kvm_pmu_enable_counter_mask(struct kvm_vcpu *vcpu, u64 val)
 	if (!kvm_vcpu_has_pmu(vcpu))
 		return;
 
-	if (!(__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E) || !val)
+	if (!(kvm_vcpu_read_pmcr(vcpu) & ARMV8_PMU_PMCR_E) || !val)
 		return;
 
 	for (i = 0; i < ARMV8_PMU_MAX_COUNTERS; i++) {
@@ -324,7 +324,7 @@ static u64 kvm_pmu_overflow_status(struct kvm_vcpu *vcpu)
 {
 	u64 reg = 0;
 
-	if ((__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E)) {
+	if ((kvm_vcpu_read_pmcr(vcpu) & ARMV8_PMU_PMCR_E)) {
 		reg = __vcpu_sys_reg(vcpu, PMOVSSET_EL0);
 		reg &= __vcpu_sys_reg(vcpu, PMCNTENSET_EL0);
 		reg &= __vcpu_sys_reg(vcpu, PMINTENSET_EL1);
@@ -426,7 +426,7 @@ static void kvm_pmu_counter_increment(struct kvm_vcpu *vcpu,
 {
 	int i;
 
-	if (!(__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E))
+	if (!(kvm_vcpu_read_pmcr(vcpu) & ARMV8_PMU_PMCR_E))
 		return;
 
 	/* Weed out disabled counters */
@@ -569,7 +569,7 @@ void kvm_pmu_handle_pmcr(struct kvm_vcpu *vcpu, u64 val)
 static bool kvm_pmu_counter_is_enabled(struct kvm_pmc *pmc)
 {
 	struct kvm_vcpu *vcpu = kvm_pmc_to_vcpu(pmc);
-	return (__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E) &&
+	return (kvm_vcpu_read_pmcr(vcpu) & ARMV8_PMU_PMCR_E) &&
 	       (__vcpu_sys_reg(vcpu, PMCNTENSET_EL0) & BIT(pmc->idx));
 }
 
@@ -1084,3 +1084,12 @@ u8 kvm_arm_pmu_get_pmuver_limit(void)
 					      ID_AA64DFR0_EL1_PMUVer_V3P5);
 	return FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_PMUVer), tmp);
 }
+
+/**
+ * kvm_vcpu_read_pmcr - Read PMCR_EL0 register for the vCPU
+ * @vcpu: The vcpu pointer
+ */
+u64 kvm_vcpu_read_pmcr(struct kvm_vcpu *vcpu)
+{
+	return __vcpu_sys_reg(vcpu, PMCR_EL0);
+}
diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index 66b9e1de54230..5ae7399f2b822 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -803,7 +803,7 @@ static bool access_pmcr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
 		 * Only update writeable bits of PMCR (continuing into
 		 * kvm_pmu_handle_pmcr() as well)
 		 */
-		val = __vcpu_sys_reg(vcpu, PMCR_EL0);
+		val = kvm_vcpu_read_pmcr(vcpu);
 		val &= ~ARMV8_PMU_PMCR_MASK;
 		val |= p->regval & ARMV8_PMU_PMCR_MASK;
 		if (!kvm_supports_32bit_el0())
@@ -811,7 +811,7 @@ static bool access_pmcr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
 		kvm_pmu_handle_pmcr(vcpu, val);
 	} else {
 		/* PMCR.P & PMCR.C are RAZ */
-		val = __vcpu_sys_reg(vcpu, PMCR_EL0)
+		val = kvm_vcpu_read_pmcr(vcpu)
 		      & ~(ARMV8_PMU_PMCR_P | ARMV8_PMU_PMCR_C);
 		p->regval = val;
 	}
@@ -860,7 +860,7 @@ static bool pmu_counter_idx_valid(struct kvm_vcpu *vcpu, u64 idx)
 {
 	u64 pmcr, val;
 
-	pmcr = __vcpu_sys_reg(vcpu, PMCR_EL0);
+	pmcr = kvm_vcpu_read_pmcr(vcpu);
 	val = (pmcr >> ARMV8_PMU_PMCR_N_SHIFT) & ARMV8_PMU_PMCR_N_MASK;
 	if (idx >= val && idx != ARMV8_PMU_CYCLE_IDX) {
 		kvm_inject_undefined(vcpu);
diff --git a/include/kvm/arm_pmu.h b/include/kvm/arm_pmu.h
index b80c75d80886b..c6a5e49b850ab 100644
--- a/include/kvm/arm_pmu.h
+++ b/include/kvm/arm_pmu.h
@@ -103,6 +103,7 @@ void kvm_vcpu_pmu_resync_el0(void);
 u8 kvm_arm_pmu_get_pmuver_limit(void);
 int kvm_arm_set_default_pmu(struct kvm *kvm);
 
+u64 kvm_vcpu_read_pmcr(struct kvm_vcpu *vcpu);
 #else
 struct kvm_pmu {
 };
@@ -180,6 +181,11 @@ static inline int kvm_arm_set_default_pmu(struct kvm *kvm)
 	return -ENODEV;
 }
 
+static inline u64 kvm_vcpu_read_pmcr(struct kvm_vcpu *vcpu)
+{
+	return 0;
+}
+
 #endif
 
 #endif
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 06/11] KVM: arm64: PMU: Set PMCR_EL0.N for vCPU based on the associated PMU

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

The number of PMU event counters is indicated in PMCR_EL0.N.
For a vCPU with PMUv3 configured, the value is set to the same
value as the current PE on every vCPU reset.  Unless the vCPU is
pinned to PEs that has the PMU associated to the guest from the
initial vCPU reset, the value might be different from the PMU's
PMCR_EL0.N on heterogeneous PMU systems.

Fix this by setting the vCPU's PMCR_EL0.N to the PMU's PMCR_EL0.N
value. Track the PMCR_EL0.N per guest, as only one PMU can be set
for the guest (PMCR_EL0.N must be the same for all vCPUs of the
guest), and it is convenient for updating the value.

KVM does not yet support userspace modifying PMCR_EL0.N.
The following patch will add support for that.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/include/asm/kvm_host.h |  3 +++
 arch/arm64/kvm/pmu-emul.c         | 20 +++++++++++++++++++-
 arch/arm64/kvm/sys_regs.c         | 15 +++++++++------
 3 files changed, 31 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/include/asm/kvm_host.h b/arch/arm64/include/asm/kvm_host.h
index af06ccb7ee343..0fe9cc9dc8368 100644
--- a/arch/arm64/include/asm/kvm_host.h
+++ b/arch/arm64/include/asm/kvm_host.h
@@ -257,6 +257,9 @@ struct kvm_arch {
 
 	cpumask_var_t supported_cpus;
 
+	/* PMCR_EL0.N value for the guest */
+	u8 pmcr_n;
+
 	/* Hypercall features firmware registers' descriptor */
 	struct kvm_smccc_features smccc_feat;
 	struct maple_tree smccc_filter;
diff --git a/arch/arm64/kvm/pmu-emul.c b/arch/arm64/kvm/pmu-emul.c
index d89438956f7d3..121cfd161959a 100644
--- a/arch/arm64/kvm/pmu-emul.c
+++ b/arch/arm64/kvm/pmu-emul.c
@@ -690,6 +690,9 @@ void kvm_host_pmu_init(struct arm_pmu *pmu)
 	if (!entry)
 		goto out_unlock;
 
+	WARN_ON((pmu->num_events <= 0) ||
+		(pmu->num_events > ARMV8_PMU_MAX_COUNTERS));
+
 	entry->arm_pmu = pmu;
 	list_add_tail(&entry->entry, &arm_pmus);
 
@@ -878,6 +881,13 @@ static void kvm_arm_set_pmu(struct kvm *kvm, struct arm_pmu *arm_pmu)
 	lockdep_assert_held(&kvm->arch.config_lock);
 
 	kvm->arch.arm_pmu = arm_pmu;
+
+	/*
+	 * Both the num_events and PMCR_EL0.N indicates the number of
+	 * PMU event counters, but the former includes the cycle counter
+	 * while the latter does not.
+	 */
+	kvm->arch.pmcr_n = arm_pmu->num_events - 1;
 }
 
 /**
@@ -1088,8 +1098,16 @@ u8 kvm_arm_pmu_get_pmuver_limit(void)
 /**
  * kvm_vcpu_read_pmcr - Read PMCR_EL0 register for the vCPU
  * @vcpu: The vcpu pointer
+ *
+ * The function returns the value of PMCR.N based on the per-VM tracked
+ * value (kvm->arch.pmcr_n). This is to ensure that the register field
+ * remains consistent for the VM, even on heterogeneous systems where
+ * the value may vary when read from different CPUs (during vCPU reset).
  */
 u64 kvm_vcpu_read_pmcr(struct kvm_vcpu *vcpu)
 {
-	return __vcpu_sys_reg(vcpu, PMCR_EL0);
+	u64 pmcr = __vcpu_sys_reg(vcpu, PMCR_EL0) &
+			~(ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT);
+
+	return pmcr | ((u64)vcpu->kvm->arch.pmcr_n << ARMV8_PMU_PMCR_N_SHIFT);
 }
diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index 5ae7399f2b822..d1db1f292645e 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -745,12 +745,8 @@ static u64 reset_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r)
 {
 	u64 pmcr;
 
-	/* No PMU available, PMCR_EL0 may UNDEF... */
-	if (!kvm_arm_support_pmu_v3())
-		return 0;
-
 	/* Only preserve PMCR_EL0.N, and reset the rest to 0 */
-	pmcr = read_sysreg(pmcr_el0) & (ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT);
+	pmcr = kvm_vcpu_read_pmcr(vcpu) & (ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT);
 	if (!kvm_supports_32bit_el0())
 		pmcr |= ARMV8_PMU_PMCR_LC;
 
@@ -1084,6 +1080,13 @@ static bool access_pmuserenr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
 	return true;
 }
 
+static int get_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		    u64 *val)
+{
+	*val = kvm_vcpu_read_pmcr(vcpu);
+	return 0;
+}
+
 /* Silly macro to expand the DBG{BCR,BVR,WVR,WCR}n_EL1 registers in one go */
 #define DBG_BCR_BVR_WCR_WVR_EL1(n)					\
 	{ SYS_DESC(SYS_DBGBVRn_EL1(n)),					\
@@ -2148,7 +2151,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	{ SYS_DESC(SYS_SVCR), undef_access },
 
 	{ PMU_SYS_REG(PMCR_EL0), .access = access_pmcr,
-	  .reset = reset_pmcr, .reg = PMCR_EL0 },
+	  .reset = reset_pmcr, .reg = PMCR_EL0, .get_user = get_pmcr },
 	{ PMU_SYS_REG(PMCNTENSET_EL0),
 	  .access = access_pmcnten, .reg = PMCNTENSET_EL0 },
 	{ PMU_SYS_REG(PMCNTENCLR_EL0),
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 07/11] KVM: arm64: PMU: Allow userspace to limit PMCR_EL0.N for the guest

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

KVM does not yet support userspace modifying PMCR_EL0.N (With
the previous patch, KVM ignores what is written by userspace).
Add support userspace limiting PMCR_EL0.N.

Disallow userspace to set PMCR_EL0.N to a value that is greater
than the host value as KVM doesn't support more event counters
than what the host HW implements. Also, make this register
immutable after the VM has started running. To maintain the
existing expectations, instead of returning an error, KVM
returns a success for these two cases.

Finally, ignore writes to read-only bits that are cleared on
vCPU reset, and RES{0,1} bits (including writable bits that
KVM doesn't support yet), as those bits shouldn't be modified
(at least with the current KVM).

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 arch/arm64/kvm/sys_regs.c | 58 +++++++++++++++++++++++++++++++++++++--
 1 file changed, 56 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index d1db1f292645e..a0efc71dbee1e 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -16,6 +16,7 @@
 #include <linux/mm.h>
 #include <linux/printk.h>
 #include <linux/uaccess.h>
+#include <linux/perf/arm_pmu.h>
 
 #include <asm/cacheflush.h>
 #include <asm/cputype.h>
@@ -1087,6 +1088,59 @@ static int get_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
 	return 0;
 }
 
+static int set_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		    u64 val)
+{
+	struct kvm *kvm = vcpu->kvm;
+	u64 new_n, mutable_mask;
+
+	mutex_lock(&kvm->arch.config_lock);
+
+	/*
+	 * Make PMCR immutable once the VM has started running, but do
+	 * not return an error (-EBUSY) to meet the existing expectations.
+	 */
+	if (kvm_vm_has_ran_once(vcpu->kvm)) {
+		mutex_unlock(&kvm->arch.config_lock);
+		return 0;
+	}
+
+	new_n = (val >> ARMV8_PMU_PMCR_N_SHIFT) & ARMV8_PMU_PMCR_N_MASK;
+	if (new_n != kvm->arch.pmcr_n) {
+		u8 pmcr_n_limit = kvm->arch.arm_pmu->num_events - 1;
+
+		/*
+		 * The vCPU can't have more counters than the PMU hardware
+		 * implements. Ignore this error to maintain compatibility
+		 * with the existing KVM behavior.
+		 */
+		if (new_n <= pmcr_n_limit)
+			kvm->arch.pmcr_n = new_n;
+	}
+	mutex_unlock(&kvm->arch.config_lock);
+
+	/*
+	 * Ignore writes to RES0 bits, read only bits that are cleared on
+	 * vCPU reset, and writable bits that KVM doesn't support yet.
+	 * (i.e. only PMCR.N and bits [7:0] are mutable from userspace)
+	 * The LP bit is RES0 when FEAT_PMUv3p5 is not supported on the vCPU.
+	 * But, we leave the bit as it is here, as the vCPU's PMUver might
+	 * be changed later (NOTE: the bit will be cleared on first vCPU run
+	 * if necessary).
+	 */
+	mutable_mask = (ARMV8_PMU_PMCR_MASK |
+			(ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT));
+	val &= mutable_mask;
+	val |= (__vcpu_sys_reg(vcpu, r->reg) & ~mutable_mask);
+
+	/* The LC bit is RES1 when AArch32 is not supported */
+	if (!kvm_supports_32bit_el0())
+		val |= ARMV8_PMU_PMCR_LC;
+
+	__vcpu_sys_reg(vcpu, r->reg) = val;
+	return 0;
+}
+
 /* Silly macro to expand the DBG{BCR,BVR,WVR,WCR}n_EL1 registers in one go */
 #define DBG_BCR_BVR_WCR_WVR_EL1(n)					\
 	{ SYS_DESC(SYS_DBGBVRn_EL1(n)),					\
@@ -2150,8 +2204,8 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	{ SYS_DESC(SYS_CTR_EL0), access_ctr },
 	{ SYS_DESC(SYS_SVCR), undef_access },
 
-	{ PMU_SYS_REG(PMCR_EL0), .access = access_pmcr,
-	  .reset = reset_pmcr, .reg = PMCR_EL0, .get_user = get_pmcr },
+	{ PMU_SYS_REG(PMCR_EL0), .access = access_pmcr, .reset = reset_pmcr,
+	  .reg = PMCR_EL0, .get_user = get_pmcr, .set_user = set_pmcr },
 	{ PMU_SYS_REG(PMCNTENSET_EL0),
 	  .access = access_pmcnten, .reg = PMCNTENSET_EL0 },
 	{ PMU_SYS_REG(PMCNTENCLR_EL0),
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 08/11] tools: Import arm_pmuv3.h

[Raghavendra Rao Ananta]

Import kernel's include/linux/perf/arm_pmuv3.h, with the
definition of PMEVN_SWITCH() additionally including an assert()
for the 'default' case. The following patches will use macros
defined in this header.

Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 tools/include/perf/arm_pmuv3.h | 308 +++++++++++++++++++++++++++++++++
 1 file changed, 308 insertions(+)
 create mode 100644 tools/include/perf/arm_pmuv3.h

diff --git a/tools/include/perf/arm_pmuv3.h b/tools/include/perf/arm_pmuv3.h
new file mode 100644
index 0000000000000..e822d49fb5b88
--- /dev/null
+++ b/tools/include/perf/arm_pmuv3.h
@@ -0,0 +1,308 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2012 ARM Ltd.
+ */
+
+#ifndef __PERF_ARM_PMUV3_H
+#define __PERF_ARM_PMUV3_H
+
+#include <assert.h>
+#include <asm/bug.h>
+
+#define ARMV8_PMU_MAX_COUNTERS	32
+#define ARMV8_PMU_COUNTER_MASK	(ARMV8_PMU_MAX_COUNTERS - 1)
+
+/*
+ * Common architectural and microarchitectural event numbers.
+ */
+#define ARMV8_PMUV3_PERFCTR_SW_INCR				0x0000
+#define ARMV8_PMUV3_PERFCTR_L1I_CACHE_REFILL			0x0001
+#define ARMV8_PMUV3_PERFCTR_L1I_TLB_REFILL			0x0002
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_REFILL			0x0003
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE				0x0004
+#define ARMV8_PMUV3_PERFCTR_L1D_TLB_REFILL			0x0005
+#define ARMV8_PMUV3_PERFCTR_LD_RETIRED				0x0006
+#define ARMV8_PMUV3_PERFCTR_ST_RETIRED				0x0007
+#define ARMV8_PMUV3_PERFCTR_INST_RETIRED			0x0008
+#define ARMV8_PMUV3_PERFCTR_EXC_TAKEN				0x0009
+#define ARMV8_PMUV3_PERFCTR_EXC_RETURN				0x000A
+#define ARMV8_PMUV3_PERFCTR_CID_WRITE_RETIRED			0x000B
+#define ARMV8_PMUV3_PERFCTR_PC_WRITE_RETIRED			0x000C
+#define ARMV8_PMUV3_PERFCTR_BR_IMMED_RETIRED			0x000D
+#define ARMV8_PMUV3_PERFCTR_BR_RETURN_RETIRED			0x000E
+#define ARMV8_PMUV3_PERFCTR_UNALIGNED_LDST_RETIRED		0x000F
+#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED				0x0010
+#define ARMV8_PMUV3_PERFCTR_CPU_CYCLES				0x0011
+#define ARMV8_PMUV3_PERFCTR_BR_PRED				0x0012
+#define ARMV8_PMUV3_PERFCTR_MEM_ACCESS				0x0013
+#define ARMV8_PMUV3_PERFCTR_L1I_CACHE				0x0014
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_WB			0x0015
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE				0x0016
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_REFILL			0x0017
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_WB			0x0018
+#define ARMV8_PMUV3_PERFCTR_BUS_ACCESS				0x0019
+#define ARMV8_PMUV3_PERFCTR_MEMORY_ERROR			0x001A
+#define ARMV8_PMUV3_PERFCTR_INST_SPEC				0x001B
+#define ARMV8_PMUV3_PERFCTR_TTBR_WRITE_RETIRED			0x001C
+#define ARMV8_PMUV3_PERFCTR_BUS_CYCLES				0x001D
+#define ARMV8_PMUV3_PERFCTR_CHAIN				0x001E
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_ALLOCATE			0x001F
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_ALLOCATE			0x0020
+#define ARMV8_PMUV3_PERFCTR_BR_RETIRED				0x0021
+#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED_RETIRED			0x0022
+#define ARMV8_PMUV3_PERFCTR_STALL_FRONTEND			0x0023
+#define ARMV8_PMUV3_PERFCTR_STALL_BACKEND			0x0024
+#define ARMV8_PMUV3_PERFCTR_L1D_TLB				0x0025
+#define ARMV8_PMUV3_PERFCTR_L1I_TLB				0x0026
+#define ARMV8_PMUV3_PERFCTR_L2I_CACHE				0x0027
+#define ARMV8_PMUV3_PERFCTR_L2I_CACHE_REFILL			0x0028
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_ALLOCATE			0x0029
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_REFILL			0x002A
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE				0x002B
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_WB			0x002C
+#define ARMV8_PMUV3_PERFCTR_L2D_TLB_REFILL			0x002D
+#define ARMV8_PMUV3_PERFCTR_L2I_TLB_REFILL			0x002E
+#define ARMV8_PMUV3_PERFCTR_L2D_TLB				0x002F
+#define ARMV8_PMUV3_PERFCTR_L2I_TLB				0x0030
+#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS			0x0031
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE				0x0032
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS			0x0033
+#define ARMV8_PMUV3_PERFCTR_DTLB_WALK				0x0034
+#define ARMV8_PMUV3_PERFCTR_ITLB_WALK				0x0035
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_RD				0x0036
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS_RD			0x0037
+#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS_RD			0x0038
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_LMISS_RD			0x0039
+#define ARMV8_PMUV3_PERFCTR_OP_RETIRED				0x003A
+#define ARMV8_PMUV3_PERFCTR_OP_SPEC				0x003B
+#define ARMV8_PMUV3_PERFCTR_STALL				0x003C
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_BACKEND			0x003D
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_FRONTEND			0x003E
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT				0x003F
+
+/* Statistical profiling extension microarchitectural events */
+#define ARMV8_SPE_PERFCTR_SAMPLE_POP				0x4000
+#define ARMV8_SPE_PERFCTR_SAMPLE_FEED				0x4001
+#define ARMV8_SPE_PERFCTR_SAMPLE_FILTRATE			0x4002
+#define ARMV8_SPE_PERFCTR_SAMPLE_COLLISION			0x4003
+
+/* AMUv1 architecture events */
+#define ARMV8_AMU_PERFCTR_CNT_CYCLES				0x4004
+#define ARMV8_AMU_PERFCTR_STALL_BACKEND_MEM			0x4005
+
+/* long-latency read miss events */
+#define ARMV8_PMUV3_PERFCTR_L1I_CACHE_LMISS			0x4006
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_LMISS_RD			0x4009
+#define ARMV8_PMUV3_PERFCTR_L2I_CACHE_LMISS			0x400A
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_LMISS_RD			0x400B
+
+/* Trace buffer events */
+#define ARMV8_PMUV3_PERFCTR_TRB_WRAP				0x400C
+#define ARMV8_PMUV3_PERFCTR_TRB_TRIG				0x400E
+
+/* Trace unit events */
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT0				0x4010
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT1				0x4011
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT2				0x4012
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT3				0x4013
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT4			0x4018
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT5			0x4019
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT6			0x401A
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT7			0x401B
+
+/* additional latency from alignment events */
+#define ARMV8_PMUV3_PERFCTR_LDST_ALIGN_LAT			0x4020
+#define ARMV8_PMUV3_PERFCTR_LD_ALIGN_LAT			0x4021
+#define ARMV8_PMUV3_PERFCTR_ST_ALIGN_LAT			0x4022
+
+/* Armv8.5 Memory Tagging Extension events */
+#define ARMV8_MTE_PERFCTR_MEM_ACCESS_CHECKED			0x4024
+#define ARMV8_MTE_PERFCTR_MEM_ACCESS_CHECKED_RD			0x4025
+#define ARMV8_MTE_PERFCTR_MEM_ACCESS_CHECKED_WR			0x4026
+
+/* ARMv8 recommended implementation defined event types */
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_RD			0x0040
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WR			0x0041
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_RD		0x0042
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_WR		0x0043
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_INNER		0x0044
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_OUTER		0x0045
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_VICTIM		0x0046
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_CLEAN			0x0047
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_INVAL			0x0048
+
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_RD			0x004C
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_WR			0x004D
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_RD				0x004E
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_WR				0x004F
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_RD			0x0050
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WR			0x0051
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_RD		0x0052
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_WR		0x0053
+
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_VICTIM		0x0056
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_CLEAN			0x0057
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_INVAL			0x0058
+
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_RD			0x005C
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_WR			0x005D
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_RD				0x005E
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_WR				0x005F
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_RD			0x0060
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_WR			0x0061
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_SHARED			0x0062
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NOT_SHARED		0x0063
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NORMAL			0x0064
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_PERIPH			0x0065
+#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_RD			0x0066
+#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_WR			0x0067
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LD_SPEC			0x0068
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_ST_SPEC			0x0069
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LDST_SPEC		0x006A
+
+#define ARMV8_IMPDEF_PERFCTR_LDREX_SPEC				0x006C
+#define ARMV8_IMPDEF_PERFCTR_STREX_PASS_SPEC			0x006D
+#define ARMV8_IMPDEF_PERFCTR_STREX_FAIL_SPEC			0x006E
+#define ARMV8_IMPDEF_PERFCTR_STREX_SPEC				0x006F
+#define ARMV8_IMPDEF_PERFCTR_LD_SPEC				0x0070
+#define ARMV8_IMPDEF_PERFCTR_ST_SPEC				0x0071
+#define ARMV8_IMPDEF_PERFCTR_LDST_SPEC				0x0072
+#define ARMV8_IMPDEF_PERFCTR_DP_SPEC				0x0073
+#define ARMV8_IMPDEF_PERFCTR_ASE_SPEC				0x0074
+#define ARMV8_IMPDEF_PERFCTR_VFP_SPEC				0x0075
+#define ARMV8_IMPDEF_PERFCTR_PC_WRITE_SPEC			0x0076
+#define ARMV8_IMPDEF_PERFCTR_CRYPTO_SPEC			0x0077
+#define ARMV8_IMPDEF_PERFCTR_BR_IMMED_SPEC			0x0078
+#define ARMV8_IMPDEF_PERFCTR_BR_RETURN_SPEC			0x0079
+#define ARMV8_IMPDEF_PERFCTR_BR_INDIRECT_SPEC			0x007A
+
+#define ARMV8_IMPDEF_PERFCTR_ISB_SPEC				0x007C
+#define ARMV8_IMPDEF_PERFCTR_DSB_SPEC				0x007D
+#define ARMV8_IMPDEF_PERFCTR_DMB_SPEC				0x007E
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_UNDEF				0x0081
+#define ARMV8_IMPDEF_PERFCTR_EXC_SVC				0x0082
+#define ARMV8_IMPDEF_PERFCTR_EXC_PABORT				0x0083
+#define ARMV8_IMPDEF_PERFCTR_EXC_DABORT				0x0084
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_IRQ				0x0086
+#define ARMV8_IMPDEF_PERFCTR_EXC_FIQ				0x0087
+#define ARMV8_IMPDEF_PERFCTR_EXC_SMC				0x0088
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_HVC				0x008A
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_PABORT			0x008B
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_DABORT			0x008C
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_OTHER			0x008D
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_IRQ			0x008E
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_FIQ			0x008F
+#define ARMV8_IMPDEF_PERFCTR_RC_LD_SPEC				0x0090
+#define ARMV8_IMPDEF_PERFCTR_RC_ST_SPEC				0x0091
+
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_RD			0x00A0
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WR			0x00A1
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_RD		0x00A2
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_WR		0x00A3
+
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_VICTIM		0x00A6
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_CLEAN			0x00A7
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_INVAL			0x00A8
+
+/*
+ * Per-CPU PMCR: config reg
+ */
+#define ARMV8_PMU_PMCR_E	(1 << 0) /* Enable all counters */
+#define ARMV8_PMU_PMCR_P	(1 << 1) /* Reset all counters */
+#define ARMV8_PMU_PMCR_C	(1 << 2) /* Cycle counter reset */
+#define ARMV8_PMU_PMCR_D	(1 << 3) /* CCNT counts every 64th cpu cycle */
+#define ARMV8_PMU_PMCR_X	(1 << 4) /* Export to ETM */
+#define ARMV8_PMU_PMCR_DP	(1 << 5) /* Disable CCNT if non-invasive debug*/
+#define ARMV8_PMU_PMCR_LC	(1 << 6) /* Overflow on 64 bit cycle counter */
+#define ARMV8_PMU_PMCR_LP	(1 << 7) /* Long event counter enable */
+#define ARMV8_PMU_PMCR_N_SHIFT	11  /* Number of counters supported */
+#define ARMV8_PMU_PMCR_N_MASK	0x1f
+#define ARMV8_PMU_PMCR_MASK	0xff    /* Mask for writable bits */
+
+/*
+ * PMOVSR: counters overflow flag status reg
+ */
+#define ARMV8_PMU_OVSR_MASK		0xffffffff	/* Mask for writable bits */
+#define ARMV8_PMU_OVERFLOWED_MASK	ARMV8_PMU_OVSR_MASK
+
+/*
+ * PMXEVTYPER: Event selection reg
+ */
+#define ARMV8_PMU_EVTYPE_MASK	0xc800ffff	/* Mask for writable bits */
+#define ARMV8_PMU_EVTYPE_EVENT	0xffff		/* Mask for EVENT bits */
+
+/*
+ * Event filters for PMUv3
+ */
+#define ARMV8_PMU_EXCLUDE_EL1	(1U << 31)
+#define ARMV8_PMU_EXCLUDE_EL0	(1U << 30)
+#define ARMV8_PMU_INCLUDE_EL2	(1U << 27)
+
+/*
+ * PMUSERENR: user enable reg
+ */
+#define ARMV8_PMU_USERENR_MASK	0xf		/* Mask for writable bits */
+#define ARMV8_PMU_USERENR_EN	(1 << 0) /* PMU regs can be accessed at EL0 */
+#define ARMV8_PMU_USERENR_SW	(1 << 1) /* PMSWINC can be written at EL0 */
+#define ARMV8_PMU_USERENR_CR	(1 << 2) /* Cycle counter can be read at EL0 */
+#define ARMV8_PMU_USERENR_ER	(1 << 3) /* Event counter can be read at EL0 */
+
+/* PMMIR_EL1.SLOTS mask */
+#define ARMV8_PMU_SLOTS_MASK	0xff
+
+#define ARMV8_PMU_BUS_SLOTS_SHIFT 8
+#define ARMV8_PMU_BUS_SLOTS_MASK 0xff
+#define ARMV8_PMU_BUS_WIDTH_SHIFT 16
+#define ARMV8_PMU_BUS_WIDTH_MASK 0xf
+
+/*
+ * This code is really good
+ */
+
+#define PMEVN_CASE(n, case_macro) \
+	case n: case_macro(n); break
+
+#define PMEVN_SWITCH(x, case_macro)				\
+	do {							\
+		switch (x) {					\
+		PMEVN_CASE(0,  case_macro);			\
+		PMEVN_CASE(1,  case_macro);			\
+		PMEVN_CASE(2,  case_macro);			\
+		PMEVN_CASE(3,  case_macro);			\
+		PMEVN_CASE(4,  case_macro);			\
+		PMEVN_CASE(5,  case_macro);			\
+		PMEVN_CASE(6,  case_macro);			\
+		PMEVN_CASE(7,  case_macro);			\
+		PMEVN_CASE(8,  case_macro);			\
+		PMEVN_CASE(9,  case_macro);			\
+		PMEVN_CASE(10, case_macro);			\
+		PMEVN_CASE(11, case_macro);			\
+		PMEVN_CASE(12, case_macro);			\
+		PMEVN_CASE(13, case_macro);			\
+		PMEVN_CASE(14, case_macro);			\
+		PMEVN_CASE(15, case_macro);			\
+		PMEVN_CASE(16, case_macro);			\
+		PMEVN_CASE(17, case_macro);			\
+		PMEVN_CASE(18, case_macro);			\
+		PMEVN_CASE(19, case_macro);			\
+		PMEVN_CASE(20, case_macro);			\
+		PMEVN_CASE(21, case_macro);			\
+		PMEVN_CASE(22, case_macro);			\
+		PMEVN_CASE(23, case_macro);			\
+		PMEVN_CASE(24, case_macro);			\
+		PMEVN_CASE(25, case_macro);			\
+		PMEVN_CASE(26, case_macro);			\
+		PMEVN_CASE(27, case_macro);			\
+		PMEVN_CASE(28, case_macro);			\
+		PMEVN_CASE(29, case_macro);			\
+		PMEVN_CASE(30, case_macro);			\
+		default:					\
+			WARN(1, "Invalid PMEV* index\n");	\
+			assert(0);				\
+		}						\
+	} while (0)
+
+#endif
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 09/11] KVM: selftests: aarch64: Introduce vpmu_counter_access test

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

Introduce vpmu_counter_access test for arm64 platforms.
The test configures PMUv3 for a vCPU, sets PMCR_EL0.N for the vCPU,
and check if the guest can consistently see the same number of the
PMU event counters (PMCR_EL0.N) that userspace sets.
This test case is done with each of the PMCR_EL0.N values from
0 to 31 (With the PMCR_EL0.N values greater than the host value,
the test expects KVM_SET_ONE_REG for the PMCR_EL0 to fail).

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 tools/testing/selftests/kvm/Makefile          |   1 +
 .../kvm/aarch64/vpmu_counter_access.c         | 247 ++++++++++++++++++
 2 files changed, 248 insertions(+)
 create mode 100644 tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c

diff --git a/tools/testing/selftests/kvm/Makefile b/tools/testing/selftests/kvm/Makefile
index a3bb36fb3cfc5..416700aa196ca 100644
--- a/tools/testing/selftests/kvm/Makefile
+++ b/tools/testing/selftests/kvm/Makefile
@@ -149,6 +149,7 @@ TEST_GEN_PROGS_aarch64 += aarch64/smccc_filter
 TEST_GEN_PROGS_aarch64 += aarch64/vcpu_width_config
 TEST_GEN_PROGS_aarch64 += aarch64/vgic_init
 TEST_GEN_PROGS_aarch64 += aarch64/vgic_irq
+TEST_GEN_PROGS_aarch64 += aarch64/vpmu_counter_access
 TEST_GEN_PROGS_aarch64 += access_tracking_perf_test
 TEST_GEN_PROGS_aarch64 += demand_paging_test
 TEST_GEN_PROGS_aarch64 += dirty_log_test
diff --git a/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
new file mode 100644
index 0000000000000..58949b17d76e5
--- /dev/null
+++ b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * vpmu_counter_access - Test vPMU event counter access
+ *
+ * Copyright (c) 2022 Google LLC.
+ *
+ * This test checks if the guest can see the same number of the PMU event
+ * counters (PMCR_EL0.N) that userspace sets.
+ * This test runs only when KVM_CAP_ARM_PMU_V3 is supported on the host.
+ */
+#include <kvm_util.h>
+#include <processor.h>
+#include <test_util.h>
+#include <vgic.h>
+#include <perf/arm_pmuv3.h>
+#include <linux/bitfield.h>
+
+/* The max number of the PMU event counters (excluding the cycle counter) */
+#define ARMV8_PMU_MAX_GENERAL_COUNTERS	(ARMV8_PMU_MAX_COUNTERS - 1)
+
+struct vpmu_vm {
+	struct kvm_vm *vm;
+	struct kvm_vcpu *vcpu;
+	int gic_fd;
+};
+
+static struct vpmu_vm vpmu_vm;
+
+static uint64_t get_pmcr_n(uint64_t pmcr)
+{
+	return (pmcr >> ARMV8_PMU_PMCR_N_SHIFT) & ARMV8_PMU_PMCR_N_MASK;
+}
+
+static void set_pmcr_n(uint64_t *pmcr, uint64_t pmcr_n)
+{
+	*pmcr = *pmcr & ~(ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT);
+	*pmcr |= (pmcr_n << ARMV8_PMU_PMCR_N_SHIFT);
+}
+
+static void guest_sync_handler(struct ex_regs *regs)
+{
+	uint64_t esr, ec;
+
+	esr = read_sysreg(esr_el1);
+	ec = (esr >> ESR_EC_SHIFT) & ESR_EC_MASK;
+	__GUEST_ASSERT(0, "PC: 0x%lx; ESR: 0x%lx; EC: 0x%lx", regs->pc, esr, ec);
+}
+
+/*
+ * The guest is configured with PMUv3 with @expected_pmcr_n number of
+ * event counters.
+ * Check if @expected_pmcr_n is consistent with PMCR_EL0.N.
+ */
+static void guest_code(uint64_t expected_pmcr_n)
+{
+	uint64_t pmcr, pmcr_n;
+
+	__GUEST_ASSERT(expected_pmcr_n <= ARMV8_PMU_MAX_GENERAL_COUNTERS,
+			"Expected PMCR.N: 0x%lx; ARMv8 general counters: 0x%lx",
+			expected_pmcr_n, ARMV8_PMU_MAX_GENERAL_COUNTERS);
+
+	pmcr = read_sysreg(pmcr_el0);
+	pmcr_n = get_pmcr_n(pmcr);
+
+	/* Make sure that PMCR_EL0.N indicates the value userspace set */
+	__GUEST_ASSERT(pmcr_n == expected_pmcr_n,
+			"Expected PMCR.N: 0x%lx, PMCR.N: 0x%lx",
+			pmcr_n, expected_pmcr_n);
+
+	GUEST_DONE();
+}
+
+#define GICD_BASE_GPA	0x8000000ULL
+#define GICR_BASE_GPA	0x80A0000ULL
+
+/* Create a VM that has one vCPU with PMUv3 configured. */
+static void create_vpmu_vm(void *guest_code)
+{
+	struct kvm_vcpu_init init;
+	uint8_t pmuver, ec;
+	uint64_t dfr0, irq = 23;
+	struct kvm_device_attr irq_attr = {
+		.group = KVM_ARM_VCPU_PMU_V3_CTRL,
+		.attr = KVM_ARM_VCPU_PMU_V3_IRQ,
+		.addr = (uint64_t)&irq,
+	};
+	struct kvm_device_attr init_attr = {
+		.group = KVM_ARM_VCPU_PMU_V3_CTRL,
+		.attr = KVM_ARM_VCPU_PMU_V3_INIT,
+	};
+
+	/* The test creates the vpmu_vm multiple times. Ensure a clean state */
+	memset(&vpmu_vm, 0, sizeof(vpmu_vm));
+
+	vpmu_vm.vm = vm_create(1);
+	vm_init_descriptor_tables(vpmu_vm.vm);
+	for (ec = 0; ec < ESR_EC_NUM; ec++) {
+		vm_install_sync_handler(vpmu_vm.vm, VECTOR_SYNC_CURRENT, ec,
+					guest_sync_handler);
+	}
+
+	/* Create vCPU with PMUv3 */
+	vm_ioctl(vpmu_vm.vm, KVM_ARM_PREFERRED_TARGET, &init);
+	init.features[0] |= (1 << KVM_ARM_VCPU_PMU_V3);
+	vpmu_vm.vcpu = aarch64_vcpu_add(vpmu_vm.vm, 0, &init, guest_code);
+	vcpu_init_descriptor_tables(vpmu_vm.vcpu);
+	vpmu_vm.gic_fd = vgic_v3_setup(vpmu_vm.vm, 1, 64,
+					GICD_BASE_GPA, GICR_BASE_GPA);
+
+	/* Make sure that PMUv3 support is indicated in the ID register */
+	vcpu_get_reg(vpmu_vm.vcpu,
+		     KVM_ARM64_SYS_REG(SYS_ID_AA64DFR0_EL1), &dfr0);
+	pmuver = FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_PMUVER), dfr0);
+	TEST_ASSERT(pmuver != ID_AA64DFR0_PMUVER_IMP_DEF &&
+		    pmuver >= ID_AA64DFR0_PMUVER_8_0,
+		    "Unexpected PMUVER (0x%x) on the vCPU with PMUv3", pmuver);
+
+	/* Initialize vPMU */
+	vcpu_ioctl(vpmu_vm.vcpu, KVM_SET_DEVICE_ATTR, &irq_attr);
+	vcpu_ioctl(vpmu_vm.vcpu, KVM_SET_DEVICE_ATTR, &init_attr);
+}
+
+static void destroy_vpmu_vm(void)
+{
+	close(vpmu_vm.gic_fd);
+	kvm_vm_free(vpmu_vm.vm);
+}
+
+static void run_vcpu(struct kvm_vcpu *vcpu, uint64_t pmcr_n)
+{
+	struct ucall uc;
+
+	vcpu_args_set(vcpu, 1, pmcr_n);
+	vcpu_run(vcpu);
+	switch (get_ucall(vcpu, &uc)) {
+	case UCALL_ABORT:
+		REPORT_GUEST_ASSERT(uc);
+		break;
+	case UCALL_DONE:
+		break;
+	default:
+		TEST_FAIL("Unknown ucall %lu", uc.cmd);
+		break;
+	}
+}
+
+/*
+ * Create a guest with one vCPU, set the PMCR_EL0.N for the vCPU to @pmcr_n,
+ * and run the test.
+ */
+static void run_test(uint64_t pmcr_n)
+{
+	struct kvm_vcpu *vcpu;
+	uint64_t sp, pmcr;
+	struct kvm_vcpu_init init;
+
+	pr_debug("Test with pmcr_n %lu\n", pmcr_n);
+	create_vpmu_vm(guest_code);
+
+	vcpu = vpmu_vm.vcpu;
+
+	/* Save the initial sp to restore them later to run the guest again */
+	vcpu_get_reg(vcpu, ARM64_CORE_REG(sp_el1), &sp);
+
+	/* Update the PMCR_EL0.N with @pmcr_n */
+	vcpu_get_reg(vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), &pmcr);
+	set_pmcr_n(&pmcr, pmcr_n);
+	vcpu_set_reg(vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), pmcr);
+
+	run_vcpu(vcpu, pmcr_n);
+
+	/*
+	 * Reset and re-initialize the vCPU, and run the guest code again to
+	 * check if PMCR_EL0.N is preserved.
+	 */
+	vm_ioctl(vpmu_vm.vm, KVM_ARM_PREFERRED_TARGET, &init);
+	init.features[0] |= (1 << KVM_ARM_VCPU_PMU_V3);
+	aarch64_vcpu_setup(vcpu, &init);
+	vcpu_init_descriptor_tables(vcpu);
+	vcpu_set_reg(vcpu, ARM64_CORE_REG(sp_el1), sp);
+	vcpu_set_reg(vcpu, ARM64_CORE_REG(regs.pc), (uint64_t)guest_code);
+
+	run_vcpu(vcpu, pmcr_n);
+
+	destroy_vpmu_vm();
+}
+
+/*
+ * Create a guest with one vCPU, and attempt to set the PMCR_EL0.N for
+ * the vCPU to @pmcr_n, which is larger than the host value.
+ * The attempt should fail as @pmcr_n is too big to set for the vCPU.
+ */
+static void run_error_test(uint64_t pmcr_n)
+{
+	struct kvm_vcpu *vcpu;
+	uint64_t pmcr, pmcr_orig;
+
+	pr_debug("Error test with pmcr_n %lu (larger than the host)\n", pmcr_n);
+	create_vpmu_vm(guest_code);
+	vcpu = vpmu_vm.vcpu;
+
+	vcpu_get_reg(vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), &pmcr_orig);
+	pmcr = pmcr_orig;
+
+	/*
+	 * Setting a larger value of PMCR.N should not modify the field, and
+	 * return a success.
+	 */
+	set_pmcr_n(&pmcr, pmcr_n);
+	vcpu_set_reg(vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), pmcr);
+	vcpu_get_reg(vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), &pmcr);
+	TEST_ASSERT(pmcr_orig == pmcr,
+		    "PMCR.N modified by KVM to a larger value (PMCR: 0x%lx) for pmcr_n: 0x%lx\n",
+		    pmcr, pmcr_n);
+
+	destroy_vpmu_vm();
+}
+
+/*
+ * Return the default number of implemented PMU event counters excluding
+ * the cycle counter (i.e. PMCR_EL0.N value) for the guest.
+ */
+static uint64_t get_pmcr_n_limit(void)
+{
+	uint64_t pmcr;
+
+	create_vpmu_vm(guest_code);
+	vcpu_get_reg(vpmu_vm.vcpu, KVM_ARM64_SYS_REG(SYS_PMCR_EL0), &pmcr);
+	destroy_vpmu_vm();
+	return get_pmcr_n(pmcr);
+}
+
+int main(void)
+{
+	uint64_t i, pmcr_n;
+
+	TEST_REQUIRE(kvm_has_cap(KVM_CAP_ARM_PMU_V3));
+
+	pmcr_n = get_pmcr_n_limit();
+	for (i = 0; i <= pmcr_n; i++)
+		run_test(i);
+
+	for (i = pmcr_n + 1; i < ARMV8_PMU_MAX_COUNTERS; i++)
+		run_error_test(i);
+
+	return 0;
+}
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 10/11] KVM: selftests: aarch64: vPMU register test for implemented counters

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

Add a new test case to the vpmu_counter_access test to check if PMU
registers or their bits for implemented counters on the vCPU are
readable/writable as expected, and can be programmed to count events.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 .../kvm/aarch64/vpmu_counter_access.c         | 270 +++++++++++++++++-
 1 file changed, 268 insertions(+), 2 deletions(-)

diff --git a/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
index 58949b17d76e5..e92af3c0db039 100644
--- a/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
+++ b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
@@ -5,7 +5,8 @@
  * Copyright (c) 2022 Google LLC.
  *
  * This test checks if the guest can see the same number of the PMU event
- * counters (PMCR_EL0.N) that userspace sets.
+ * counters (PMCR_EL0.N) that userspace sets, and if the guest can access
+ * those counters.
  * This test runs only when KVM_CAP_ARM_PMU_V3 is supported on the host.
  */
 #include <kvm_util.h>
@@ -37,6 +38,259 @@ static void set_pmcr_n(uint64_t *pmcr, uint64_t pmcr_n)
 	*pmcr |= (pmcr_n << ARMV8_PMU_PMCR_N_SHIFT);
 }
 
+/* Read PMEVTCNTR<n>_EL0 through PMXEVCNTR_EL0 */
+static inline unsigned long read_sel_evcntr(int sel)
+{
+	write_sysreg(sel, pmselr_el0);
+	isb();
+	return read_sysreg(pmxevcntr_el0);
+}
+
+/* Write PMEVTCNTR<n>_EL0 through PMXEVCNTR_EL0 */
+static inline void write_sel_evcntr(int sel, unsigned long val)
+{
+	write_sysreg(sel, pmselr_el0);
+	isb();
+	write_sysreg(val, pmxevcntr_el0);
+	isb();
+}
+
+/* Read PMEVTYPER<n>_EL0 through PMXEVTYPER_EL0 */
+static inline unsigned long read_sel_evtyper(int sel)
+{
+	write_sysreg(sel, pmselr_el0);
+	isb();
+	return read_sysreg(pmxevtyper_el0);
+}
+
+/* Write PMEVTYPER<n>_EL0 through PMXEVTYPER_EL0 */
+static inline void write_sel_evtyper(int sel, unsigned long val)
+{
+	write_sysreg(sel, pmselr_el0);
+	isb();
+	write_sysreg(val, pmxevtyper_el0);
+	isb();
+}
+
+static inline void enable_counter(int idx)
+{
+	uint64_t v = read_sysreg(pmcntenset_el0);
+
+	write_sysreg(BIT(idx) | v, pmcntenset_el0);
+	isb();
+}
+
+static inline void disable_counter(int idx)
+{
+	uint64_t v = read_sysreg(pmcntenset_el0);
+
+	write_sysreg(BIT(idx) | v, pmcntenclr_el0);
+	isb();
+}
+
+static void pmu_disable_reset(void)
+{
+	uint64_t pmcr = read_sysreg(pmcr_el0);
+
+	/* Reset all counters, disabling them */
+	pmcr &= ~ARMV8_PMU_PMCR_E;
+	write_sysreg(pmcr | ARMV8_PMU_PMCR_P, pmcr_el0);
+	isb();
+}
+
+#define RETURN_READ_PMEVCNTRN(n) \
+	return read_sysreg(pmevcntr##n##_el0)
+static unsigned long read_pmevcntrn(int n)
+{
+	PMEVN_SWITCH(n, RETURN_READ_PMEVCNTRN);
+	return 0;
+}
+
+#define WRITE_PMEVCNTRN(n) \
+	write_sysreg(val, pmevcntr##n##_el0)
+static void write_pmevcntrn(int n, unsigned long val)
+{
+	PMEVN_SWITCH(n, WRITE_PMEVCNTRN);
+	isb();
+}
+
+#define READ_PMEVTYPERN(n) \
+	return read_sysreg(pmevtyper##n##_el0)
+static unsigned long read_pmevtypern(int n)
+{
+	PMEVN_SWITCH(n, READ_PMEVTYPERN);
+	return 0;
+}
+
+#define WRITE_PMEVTYPERN(n) \
+	write_sysreg(val, pmevtyper##n##_el0)
+static void write_pmevtypern(int n, unsigned long val)
+{
+	PMEVN_SWITCH(n, WRITE_PMEVTYPERN);
+	isb();
+}
+
+/*
+ * The pmc_accessor structure has pointers to PMEVT{CNTR,TYPER}<n>_EL0
+ * accessors that test cases will use. Each of the accessors will
+ * either directly reads/writes PMEVT{CNTR,TYPER}<n>_EL0
+ * (i.e. {read,write}_pmev{cnt,type}rn()), or reads/writes them through
+ * PMXEV{CNTR,TYPER}_EL0 (i.e. {read,write}_sel_ev{cnt,type}r()).
+ *
+ * This is used to test that combinations of those accessors provide
+ * the consistent behavior.
+ */
+struct pmc_accessor {
+	/* A function to be used to read PMEVTCNTR<n>_EL0 */
+	unsigned long	(*read_cntr)(int idx);
+	/* A function to be used to write PMEVTCNTR<n>_EL0 */
+	void		(*write_cntr)(int idx, unsigned long val);
+	/* A function to be used to read PMEVTYPER<n>_EL0 */
+	unsigned long	(*read_typer)(int idx);
+	/* A function to be used to write PMEVTYPER<n>_EL0 */
+	void		(*write_typer)(int idx, unsigned long val);
+};
+
+struct pmc_accessor pmc_accessors[] = {
+	/* test with all direct accesses */
+	{ read_pmevcntrn, write_pmevcntrn, read_pmevtypern, write_pmevtypern },
+	/* test with all indirect accesses */
+	{ read_sel_evcntr, write_sel_evcntr, read_sel_evtyper, write_sel_evtyper },
+	/* read with direct accesses, and write with indirect accesses */
+	{ read_pmevcntrn, write_sel_evcntr, read_pmevtypern, write_sel_evtyper },
+	/* read with indirect accesses, and write with direct accesses */
+	{ read_sel_evcntr, write_pmevcntrn, read_sel_evtyper, write_pmevtypern },
+};
+
+/*
+ * Convert a pointer of pmc_accessor to an index in pmc_accessors[],
+ * assuming that the pointer is one of the entries in pmc_accessors[].
+ */
+#define PMC_ACC_TO_IDX(acc)	(acc - &pmc_accessors[0])
+
+#define GUEST_ASSERT_BITMAP_REG(regname, mask, set_expected)			 \
+{										 \
+	uint64_t _tval = read_sysreg(regname);					 \
+										 \
+	if (set_expected)							 \
+		__GUEST_ASSERT((_tval & mask),					 \
+				"tval: 0x%lx; mask: 0x%lx; set_expected: 0x%lx", \
+				_tval, mask, set_expected);			 \
+	else									 \
+		__GUEST_ASSERT(!(_tval & mask),					 \
+				"tval: 0x%lx; mask: 0x%lx; set_expected: 0x%lx", \
+				_tval, mask, set_expected);			 \
+}
+
+/*
+ * Check if @mask bits in {PMCNTEN,PMINTEN,PMOVS}{SET,CLR} registers
+ * are set or cleared as specified in @set_expected.
+ */
+static void check_bitmap_pmu_regs(uint64_t mask, bool set_expected)
+{
+	GUEST_ASSERT_BITMAP_REG(pmcntenset_el0, mask, set_expected);
+	GUEST_ASSERT_BITMAP_REG(pmcntenclr_el0, mask, set_expected);
+	GUEST_ASSERT_BITMAP_REG(pmintenset_el1, mask, set_expected);
+	GUEST_ASSERT_BITMAP_REG(pmintenclr_el1, mask, set_expected);
+	GUEST_ASSERT_BITMAP_REG(pmovsset_el0, mask, set_expected);
+	GUEST_ASSERT_BITMAP_REG(pmovsclr_el0, mask, set_expected);
+}
+
+/*
+ * Check if the bit in {PMCNTEN,PMINTEN,PMOVS}{SET,CLR} registers corresponding
+ * to the specified counter (@pmc_idx) can be read/written as expected.
+ * When @set_op is true, it tries to set the bit for the counter in
+ * those registers by writing the SET registers (the bit won't be set
+ * if the counter is not implemented though).
+ * Otherwise, it tries to clear the bits in the registers by writing
+ * the CLR registers.
+ * Then, it checks if the values indicated in the registers are as expected.
+ */
+static void test_bitmap_pmu_regs(int pmc_idx, bool set_op)
+{
+	uint64_t pmcr_n, test_bit = BIT(pmc_idx);
+	bool set_expected = false;
+
+	if (set_op) {
+		write_sysreg(test_bit, pmcntenset_el0);
+		write_sysreg(test_bit, pmintenset_el1);
+		write_sysreg(test_bit, pmovsset_el0);
+
+		/* The bit will be set only if the counter is implemented */
+		pmcr_n = get_pmcr_n(read_sysreg(pmcr_el0));
+		set_expected = (pmc_idx < pmcr_n) ? true : false;
+	} else {
+		write_sysreg(test_bit, pmcntenclr_el0);
+		write_sysreg(test_bit, pmintenclr_el1);
+		write_sysreg(test_bit, pmovsclr_el0);
+	}
+	check_bitmap_pmu_regs(test_bit, set_expected);
+}
+
+/*
+ * Tests for reading/writing registers for the (implemented) event counter
+ * specified by @pmc_idx.
+ */
+static void test_access_pmc_regs(struct pmc_accessor *acc, int pmc_idx)
+{
+	uint64_t write_data, read_data;
+
+	/* Disable all PMCs and reset all PMCs to zero. */
+	pmu_disable_reset();
+
+
+	/*
+	 * Tests for reading/writing {PMCNTEN,PMINTEN,PMOVS}{SET,CLR}_EL1.
+	 */
+
+	/* Make sure that the bit in those registers are set to 0 */
+	test_bitmap_pmu_regs(pmc_idx, false);
+	/* Test if setting the bit in those registers works */
+	test_bitmap_pmu_regs(pmc_idx, true);
+	/* Test if clearing the bit in those registers works */
+	test_bitmap_pmu_regs(pmc_idx, false);
+
+
+	/*
+	 * Tests for reading/writing the event type register.
+	 */
+
+	read_data = acc->read_typer(pmc_idx);
+	/*
+	 * Set the event type register to an arbitrary value just for testing
+	 * of reading/writing the register.
+	 * ArmARM says that for the event from 0x0000 to 0x003F,
+	 * the value indicated in the PMEVTYPER<n>_EL0.evtCount field is
+	 * the value written to the field even when the specified event
+	 * is not supported.
+	 */
+	write_data = (ARMV8_PMU_EXCLUDE_EL1 | ARMV8_PMUV3_PERFCTR_INST_RETIRED);
+	acc->write_typer(pmc_idx, write_data);
+	read_data = acc->read_typer(pmc_idx);
+	__GUEST_ASSERT(read_data == write_data,
+		       "pmc_idx: 0x%lx; acc_idx: 0x%lx; read_data: 0x%lx; write_data: 0x%lx",
+		       pmc_idx, PMC_ACC_TO_IDX(acc), read_data, write_data);
+
+
+	/*
+	 * Tests for reading/writing the event count register.
+	 */
+
+	read_data = acc->read_cntr(pmc_idx);
+
+	/* The count value must be 0, as it is not used after the reset */
+	__GUEST_ASSERT(read_data == 0,
+		       "pmc_idx: 0x%lx; acc_idx: 0x%lx; read_data: 0x%lx",
+		       pmc_idx, PMC_ACC_TO_IDX(acc), read_data);
+
+	write_data = read_data + pmc_idx + 0x12345;
+	acc->write_cntr(pmc_idx, write_data);
+	read_data = acc->read_cntr(pmc_idx);
+	__GUEST_ASSERT(read_data == write_data,
+		       "pmc_idx: 0x%lx; acc_idx: 0x%lx; read_data: 0x%lx; write_data: 0x%lx",
+		       pmc_idx, PMC_ACC_TO_IDX(acc), read_data, write_data);
+}
+
 static void guest_sync_handler(struct ex_regs *regs)
 {
 	uint64_t esr, ec;
@@ -49,11 +303,14 @@ static void guest_sync_handler(struct ex_regs *regs)
 /*
  * The guest is configured with PMUv3 with @expected_pmcr_n number of
  * event counters.
- * Check if @expected_pmcr_n is consistent with PMCR_EL0.N.
+ * Check if @expected_pmcr_n is consistent with PMCR_EL0.N, and
+ * if reading/writing PMU registers for implemented counters can work
+ * as expected.
  */
 static void guest_code(uint64_t expected_pmcr_n)
 {
 	uint64_t pmcr, pmcr_n;
+	int i, pmc;
 
 	__GUEST_ASSERT(expected_pmcr_n <= ARMV8_PMU_MAX_GENERAL_COUNTERS,
 			"Expected PMCR.N: 0x%lx; ARMv8 general counters: 0x%lx",
@@ -67,6 +324,15 @@ static void guest_code(uint64_t expected_pmcr_n)
 			"Expected PMCR.N: 0x%lx, PMCR.N: 0x%lx",
 			pmcr_n, expected_pmcr_n);
 
+	/*
+	 * Tests for reading/writing PMU registers for implemented counters.
+	 * Use each combination of PMEVT{CNTR,TYPER}<n>_EL0 accessor functions.
+	 */
+	for (i = 0; i < ARRAY_SIZE(pmc_accessors); i++) {
+		for (pmc = 0; pmc < pmcr_n; pmc++)
+			test_access_pmc_regs(&pmc_accessors[i], pmc);
+	}
+
 	GUEST_DONE();
 }
 
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v6 11/11] KVM: selftests: aarch64: vPMU register test for unimplemented counters

[Raghavendra Rao Ananta]

From: Reiji Watanabe <reijiw@google.com>

Add a new test case to the vpmu_counter_access test to check
if PMU registers or their bits for unimplemented counters are not
accessible or are RAZ, as expected.

Signed-off-by: Reiji Watanabe <reijiw@google.com>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
---
 .../kvm/aarch64/vpmu_counter_access.c         | 95 +++++++++++++++++--
 .../selftests/kvm/include/aarch64/processor.h |  1 +
 2 files changed, 87 insertions(+), 9 deletions(-)

diff --git a/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
index e92af3c0db039..788386ac08940 100644
--- a/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
+++ b/tools/testing/selftests/kvm/aarch64/vpmu_counter_access.c
@@ -5,8 +5,8 @@
  * Copyright (c) 2022 Google LLC.
  *
  * This test checks if the guest can see the same number of the PMU event
- * counters (PMCR_EL0.N) that userspace sets, and if the guest can access
- * those counters.
+ * counters (PMCR_EL0.N) that userspace sets, if the guest can access
+ * those counters, and if the guest cannot access any other counters.
  * This test runs only when KVM_CAP_ARM_PMU_V3 is supported on the host.
  */
 #include <kvm_util.h>
@@ -131,9 +131,9 @@ static void write_pmevtypern(int n, unsigned long val)
 }
 
 /*
- * The pmc_accessor structure has pointers to PMEVT{CNTR,TYPER}<n>_EL0
+ * The pmc_accessor structure has pointers to PMEV{CNTR,TYPER}<n>_EL0
  * accessors that test cases will use. Each of the accessors will
- * either directly reads/writes PMEVT{CNTR,TYPER}<n>_EL0
+ * either directly reads/writes PMEV{CNTR,TYPER}<n>_EL0
  * (i.e. {read,write}_pmev{cnt,type}rn()), or reads/writes them through
  * PMXEV{CNTR,TYPER}_EL0 (i.e. {read,write}_sel_ev{cnt,type}r()).
  *
@@ -291,25 +291,85 @@ static void test_access_pmc_regs(struct pmc_accessor *acc, int pmc_idx)
 		       pmc_idx, PMC_ACC_TO_IDX(acc), read_data, write_data);
 }
 
+#define INVALID_EC	(-1ul)
+uint64_t expected_ec = INVALID_EC;
+uint64_t op_end_addr;
+
 static void guest_sync_handler(struct ex_regs *regs)
 {
 	uint64_t esr, ec;
 
 	esr = read_sysreg(esr_el1);
 	ec = (esr >> ESR_EC_SHIFT) & ESR_EC_MASK;
-	__GUEST_ASSERT(0, "PC: 0x%lx; ESR: 0x%lx; EC: 0x%lx", regs->pc, esr, ec);
+
+	__GUEST_ASSERT(op_end_addr && (expected_ec == ec),
+			"PC: 0x%lx; ESR: 0x%lx; EC: 0x%lx; EC expected: 0x%lx",
+			regs->pc, esr, ec, expected_ec);
+
+	/* Will go back to op_end_addr after the handler exits */
+	regs->pc = op_end_addr;
+
+	/*
+	 * Clear op_end_addr, and setting expected_ec to INVALID_EC
+	 * as a sign that an exception has occurred.
+	 */
+	op_end_addr = 0;
+	expected_ec = INVALID_EC;
+}
+
+/*
+ * Run the given operation that should trigger an exception with the
+ * given exception class. The exception handler (guest_sync_handler)
+ * will reset op_end_addr to 0, and expected_ec to INVALID_EC, and
+ * will come back to the instruction at the @done_label.
+ * The @done_label must be a unique label in this test program.
+ */
+#define TEST_EXCEPTION(ec, ops, done_label)		\
+{							\
+	extern int done_label;				\
+							\
+	WRITE_ONCE(op_end_addr, (uint64_t)&done_label);	\
+	GUEST_ASSERT(ec != INVALID_EC);			\
+	WRITE_ONCE(expected_ec, ec);			\
+	dsb(ish);					\
+	ops;						\
+	asm volatile(#done_label":");			\
+	GUEST_ASSERT(!op_end_addr);			\
+	GUEST_ASSERT(expected_ec == INVALID_EC);	\
+}
+
+/*
+ * Tests for reading/writing registers for the unimplemented event counter
+ * specified by @pmc_idx (>= PMCR_EL0.N).
+ */
+static void test_access_invalid_pmc_regs(struct pmc_accessor *acc, int pmc_idx)
+{
+	/*
+	 * Reading/writing the event count/type registers should cause
+	 * an UNDEFINED exception.
+	 */
+	TEST_EXCEPTION(ESR_EC_UNKNOWN, acc->read_cntr(pmc_idx), inv_rd_cntr);
+	TEST_EXCEPTION(ESR_EC_UNKNOWN, acc->write_cntr(pmc_idx, 0), inv_wr_cntr);
+	TEST_EXCEPTION(ESR_EC_UNKNOWN, acc->read_typer(pmc_idx), inv_rd_typer);
+	TEST_EXCEPTION(ESR_EC_UNKNOWN, acc->write_typer(pmc_idx, 0), inv_wr_typer);
+	/*
+	 * The bit corresponding to the (unimplemented) counter in
+	 * {PMCNTEN,PMOVS}{SET,CLR}_EL1 registers should be RAZ.
+	 */
+	test_bitmap_pmu_regs(pmc_idx, 1);
+	test_bitmap_pmu_regs(pmc_idx, 0);
 }
 
 /*
  * The guest is configured with PMUv3 with @expected_pmcr_n number of
  * event counters.
  * Check if @expected_pmcr_n is consistent with PMCR_EL0.N, and
- * if reading/writing PMU registers for implemented counters can work
- * as expected.
+ * if reading/writing PMU registers for implemented or unimplemented
+ * counters can work as expected.
  */
 static void guest_code(uint64_t expected_pmcr_n)
 {
-	uint64_t pmcr, pmcr_n;
+	uint64_t pmcr, pmcr_n, unimp_mask;
 	int i, pmc;
 
 	__GUEST_ASSERT(expected_pmcr_n <= ARMV8_PMU_MAX_GENERAL_COUNTERS,
@@ -324,15 +384,32 @@ static void guest_code(uint64_t expected_pmcr_n)
 			"Expected PMCR.N: 0x%lx, PMCR.N: 0x%lx",
 			pmcr_n, expected_pmcr_n);
 
+	/*
+	 * Make sure that (RAZ) bits corresponding to unimplemented event
+	 * counters in {PMCNTEN,PMOVS}{SET,CLR}_EL1 registers are reset to zero.
+	 * (NOTE: bits for implemented event counters are reset to UNKNOWN)
+	 */
+	unimp_mask = GENMASK_ULL(ARMV8_PMU_MAX_GENERAL_COUNTERS - 1, pmcr_n);
+	check_bitmap_pmu_regs(unimp_mask, false);
+
 	/*
 	 * Tests for reading/writing PMU registers for implemented counters.
-	 * Use each combination of PMEVT{CNTR,TYPER}<n>_EL0 accessor functions.
+	 * Use each combination of PMEV{CNTR,TYPER}<n>_EL0 accessor functions.
 	 */
 	for (i = 0; i < ARRAY_SIZE(pmc_accessors); i++) {
 		for (pmc = 0; pmc < pmcr_n; pmc++)
 			test_access_pmc_regs(&pmc_accessors[i], pmc);
 	}
 
+	/*
+	 * Tests for reading/writing PMU registers for unimplemented counters.
+	 * Use each combination of PMEV{CNTR,TYPER}<n>_EL0 accessor functions.
+	 */
+	for (i = 0; i < ARRAY_SIZE(pmc_accessors); i++) {
+		for (pmc = pmcr_n; pmc < ARMV8_PMU_MAX_GENERAL_COUNTERS; pmc++)
+			test_access_invalid_pmc_regs(&pmc_accessors[i], pmc);
+	}
+
 	GUEST_DONE();
 }
 
diff --git a/tools/testing/selftests/kvm/include/aarch64/processor.h b/tools/testing/selftests/kvm/include/aarch64/processor.h
index cb537253a6b9c..c42d683102c7a 100644
--- a/tools/testing/selftests/kvm/include/aarch64/processor.h
+++ b/tools/testing/selftests/kvm/include/aarch64/processor.h
@@ -104,6 +104,7 @@ enum {
 #define ESR_EC_SHIFT		26
 #define ESR_EC_MASK		(ESR_EC_NUM - 1)
 
+#define ESR_EC_UNKNOWN		0x0
 #define ESR_EC_SVC64		0x15
 #define ESR_EC_IABT		0x21
 #define ESR_EC_DABT		0x25
-- 
2.42.0.582.g8ccd20d70d-goog


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v6 02/11] KVM: arm64: PMU: Set the default PMU for the guest on vCPU reset

[Oliver Upton]

Hi Raghu,

On Tue, Sep 26, 2023 at 11:39:59PM +0000, Raghavendra Rao Ananta wrote:
> From: Reiji Watanabe <reijiw@google.com>
> 
> The following patches will use the number of counters information
> from the arm_pmu and use this to set the PMCR.N for the guest
> during vCPU reset. However, since the guest is not associated
> with any arm_pmu until userspace configures the vPMU device
> attributes, and a reset can happen before this event, call
> kvm_arm_support_pmu_v3() just before doing the reset.
> 
> No functional change intended.

I would argue there still is a functional change here, as PMU
initialization failure now shows up on a completely different ioctl for
userspace.

> @@ -216,6 +217,18 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
>  	vcpu->arch.reset_state.reset = false;
>  	spin_unlock(&vcpu->arch.mp_state_lock);
>  
> +	if (kvm_vcpu_has_pmu(vcpu)) {
> +		if (!kvm_arm_support_pmu_v3())
> +			return -EINVAL;
> +
> +		/*
> +		 * When the vCPU has a PMU, but no PMU is set for the guest
> +		 * yet, set the default one.
> +		 */
> +		if (unlikely(!kvm->arch.arm_pmu) && kvm_arm_set_default_pmu(kvm))
> +			return -EINVAL;
> +	}
> +

Ah, this probably will not mix well with my recent change to get rid of
the return value altogether from kvm_reset_vcpu() [*]. I see two ways to
handle this:

 - Add a separate helper responsible for one-time setup of the vCPU
   called from KVM_ARM_VCPU_INIT which may fail.

 - Add a check for !kvm->arch.arm_pmu to kvm_arm_pmu_v3_init().

No strong preference, though.

[*]: https://lore.kernel.org/r/20230920195036.1169791-8-oliver.upton@linux.dev

-- 
Thanks,
Oliver

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v6 02/11] KVM: arm64: PMU: Set the default PMU for the guest on vCPU reset

[Raghavendra Rao Ananta]

Hi Oliver,

On Wed, Sep 27, 2023 at 1:02 AM Oliver Upton <oliver.upton@linux.dev> wrote:
>
> Hi Raghu,
>
> On Tue, Sep 26, 2023 at 11:39:59PM +0000, Raghavendra Rao Ananta wrote:
> > From: Reiji Watanabe <reijiw@google.com>
> >
> > The following patches will use the number of counters information
> > from the arm_pmu and use this to set the PMCR.N for the guest
> > during vCPU reset. However, since the guest is not associated
> > with any arm_pmu until userspace configures the vPMU device
> > attributes, and a reset can happen before this event, call
> > kvm_arm_support_pmu_v3() just before doing the reset.
> >
> > No functional change intended.
>
> I would argue there still is a functional change here, as PMU
> initialization failure now shows up on a completely different ioctl for
> userspace.
>
> > @@ -216,6 +217,18 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
> >       vcpu->arch.reset_state.reset = false;
> >       spin_unlock(&vcpu->arch.mp_state_lock);
> >
> > +     if (kvm_vcpu_has_pmu(vcpu)) {
> > +             if (!kvm_arm_support_pmu_v3())
> > +                     return -EINVAL;
> > +
> > +             /*
> > +              * When the vCPU has a PMU, but no PMU is set for the guest
> > +              * yet, set the default one.
> > +              */
> > +             if (unlikely(!kvm->arch.arm_pmu) && kvm_arm_set_default_pmu(kvm))
> > +                     return -EINVAL;
> > +     }
> > +
>
> Ah, this probably will not mix well with my recent change to get rid of
> the return value altogether from kvm_reset_vcpu() [*]. I see two ways to
> handle this:
>
>  - Add a separate helper responsible for one-time setup of the vCPU
>    called from KVM_ARM_VCPU_INIT which may fail.
>
>  - Add a check for !kvm->arch.arm_pmu to kvm_arm_pmu_v3_init().
>
> No strong preference, though.
>
Thanks for the pointer. I think adding it in kvm_arm_pmu_v3_init() may
not be feasible as the reset (reset_pmcr()) may happen before this
init and we may end up setting 0 as PMCR.N for the guest. I'll explore
the other option though.

Thank you.
Raghavendra
> [*]: https://lore.kernel.org/r/20230920195036.1169791-8-oliver.upton@linux.dev
>
> --
> Thanks,
> Oliver

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v6 07/11] KVM: arm64: PMU: Allow userspace to limit PMCR_EL0.N for the guest

[kernel test robot]

Hi Raghavendra,

kernel test robot noticed the following build errors:

[auto build test ERROR on 6465e260f48790807eef06b583b38ca9789b6072]

url:    https://github.com/intel-lab-lkp/linux/commits/Raghavendra-Rao-Ananta/KVM-arm64-PMU-Introduce-helpers-to-set-the-guest-s-PMU/20230927-095821
base:   6465e260f48790807eef06b583b38ca9789b6072
patch link:    https://lore.kernel.org/r/20230926234008.2348607-8-rananta%40google.com
patch subject: [PATCH v6 07/11] KVM: arm64: PMU: Allow userspace to limit PMCR_EL0.N for the guest
config: arm64-randconfig-003-20230928 (https://download.01.org/0day-ci/archive/20230929/202309290607.Qgg05wKw-lkp@intel.com/config)
compiler: aarch64-linux-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20230929/202309290607.Qgg05wKw-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202309290607.Qgg05wKw-lkp@intel.com/

All errors (new ones prefixed by >>):

   arch/arm64/kvm/sys_regs.c: In function 'set_pmcr':
>> arch/arm64/kvm/sys_regs.c:1110:52: error: invalid use of undefined type 'struct arm_pmu'
    1110 |                 u8 pmcr_n_limit = kvm->arch.arm_pmu->num_events - 1;
         |                                                    ^~
   arch/arm64/kvm/sys_regs.c: At top level:
   arch/arm64/kvm/sys_regs.c:2207:66: warning: initialized field overwritten [-Woverride-init]
    2207 |         { PMU_SYS_REG(PMCR_EL0), .access = access_pmcr, .reset = reset_pmcr,
         |                                                                  ^~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:2207:66: note: (near initialization for 'sys_reg_descs[233].reset')
   In file included from include/uapi/linux/posix_types.h:5,
                    from include/uapi/linux/types.h:14,
                    from include/linux/types.h:6,
                    from include/linux/kasan-checks.h:5,
                    from include/asm-generic/rwonce.h:26,
                    from arch/arm64/include/asm/rwonce.h:71,
                    from include/linux/compiler.h:246,
                    from include/linux/build_bug.h:5,
                    from include/linux/bitfield.h:10,
                    from arch/arm64/kvm/sys_regs.c:12:
   include/linux/stddef.h:8:14: warning: initialized field overwritten [-Woverride-init]
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2221:46: note: in expansion of macro 'NULL'
    2221 |           .access = access_pmswinc, .reset = NULL },
         |                                              ^~~~
   include/linux/stddef.h:8:14: note: (near initialization for 'sys_reg_descs[237].reset')
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2221:46: note: in expansion of macro 'NULL'
    2221 |           .access = access_pmswinc, .reset = NULL },
         |                                              ^~~~
   arch/arm64/kvm/sys_regs.c:2223:45: warning: initialized field overwritten [-Woverride-init]
    2223 |           .access = access_pmselr, .reset = reset_pmselr, .reg = PMSELR_EL0 },
         |                                             ^~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:2223:45: note: (near initialization for 'sys_reg_descs[238].reset')
   include/linux/stddef.h:8:14: warning: initialized field overwritten [-Woverride-init]
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2225:45: note: in expansion of macro 'NULL'
    2225 |           .access = access_pmceid, .reset = NULL },
         |                                             ^~~~
   include/linux/stddef.h:8:14: note: (near initialization for 'sys_reg_descs[239].reset')
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2225:45: note: in expansion of macro 'NULL'
    2225 |           .access = access_pmceid, .reset = NULL },
         |                                             ^~~~
   include/linux/stddef.h:8:14: warning: initialized field overwritten [-Woverride-init]
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2227:45: note: in expansion of macro 'NULL'
    2227 |           .access = access_pmceid, .reset = NULL },
         |                                             ^~~~
   include/linux/stddef.h:8:14: note: (near initialization for 'sys_reg_descs[240].reset')
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2227:45: note: in expansion of macro 'NULL'
    2227 |           .access = access_pmceid, .reset = NULL },
         |                                             ^~~~
   arch/arm64/kvm/sys_regs.c:2229:49: warning: initialized field overwritten [-Woverride-init]
    2229 |           .access = access_pmu_evcntr, .reset = reset_unknown,
         |                                                 ^~~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:2229:49: note: (near initialization for 'sys_reg_descs[241].reset')
   include/linux/stddef.h:8:14: warning: initialized field overwritten [-Woverride-init]
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2232:50: note: in expansion of macro 'NULL'
    2232 |           .access = access_pmu_evtyper, .reset = NULL },
         |                                                  ^~~~
   include/linux/stddef.h:8:14: note: (near initialization for 'sys_reg_descs[242].reset')
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2232:50: note: in expansion of macro 'NULL'
    2232 |           .access = access_pmu_evtyper, .reset = NULL },
         |                                                  ^~~~
   include/linux/stddef.h:8:14: warning: initialized field overwritten [-Woverride-init]
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2234:49: note: in expansion of macro 'NULL'
    2234 |           .access = access_pmu_evcntr, .reset = NULL },
         |                                                 ^~~~
   include/linux/stddef.h:8:14: note: (near initialization for 'sys_reg_descs[243].reset')
       8 | #define NULL ((void *)0)
         |              ^
   arch/arm64/kvm/sys_regs.c:2234:49: note: in expansion of macro 'NULL'
    2234 |           .access = access_pmu_evcntr, .reset = NULL },
         |                                                 ^~~~
   arch/arm64/kvm/sys_regs.c:1162:20: warning: initialized field overwritten [-Woverride-init]
    1162 |           .reset = reset_pmevcntr, .get_user = get_pmu_evcntr,          \
         |                    ^~~~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:2330:9: note: in expansion of macro 'PMU_PMEVCNTR_EL0'
    2330 |         PMU_PMEVCNTR_EL0(0),
         |         ^~~~~~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:1162:20: note: (near initialization for 'sys_reg_descs[327].reset')
    1162 |           .reset = reset_pmevcntr, .get_user = get_pmu_evcntr,          \
         |                    ^~~~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:2330:9: note: in expansion of macro 'PMU_PMEVCNTR_EL0'
    2330 |         PMU_PMEVCNTR_EL0(0),
         |         ^~~~~~~~~~~~~~~~
   arch/arm64/kvm/sys_regs.c:1162:20: warning: initialized field overwritten [-Woverride-init]
    1162 |           .reset = reset_pmevcntr, .get_user = get_pmu_evcntr,          \
         |                    ^~~~~~~~~~~~~~


vim +1110 arch/arm64/kvm/sys_regs.c

  1090	
  1091	static int set_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
  1092			    u64 val)
  1093	{
  1094		struct kvm *kvm = vcpu->kvm;
  1095		u64 new_n, mutable_mask;
  1096	
  1097		mutex_lock(&kvm->arch.config_lock);
  1098	
  1099		/*
  1100		 * Make PMCR immutable once the VM has started running, but do
  1101		 * not return an error (-EBUSY) to meet the existing expectations.
  1102		 */
  1103		if (kvm_vm_has_ran_once(vcpu->kvm)) {
  1104			mutex_unlock(&kvm->arch.config_lock);
  1105			return 0;
  1106		}
  1107	
  1108		new_n = (val >> ARMV8_PMU_PMCR_N_SHIFT) & ARMV8_PMU_PMCR_N_MASK;
  1109		if (new_n != kvm->arch.pmcr_n) {
> 1110			u8 pmcr_n_limit = kvm->arch.arm_pmu->num_events - 1;
  1111	
  1112			/*
  1113			 * The vCPU can't have more counters than the PMU hardware
  1114			 * implements. Ignore this error to maintain compatibility
  1115			 * with the existing KVM behavior.
  1116			 */
  1117			if (new_n <= pmcr_n_limit)
  1118				kvm->arch.pmcr_n = new_n;
  1119		}
  1120		mutex_unlock(&kvm->arch.config_lock);
  1121	
  1122		/*
  1123		 * Ignore writes to RES0 bits, read only bits that are cleared on
  1124		 * vCPU reset, and writable bits that KVM doesn't support yet.
  1125		 * (i.e. only PMCR.N and bits [7:0] are mutable from userspace)
  1126		 * The LP bit is RES0 when FEAT_PMUv3p5 is not supported on the vCPU.
  1127		 * But, we leave the bit as it is here, as the vCPU's PMUver might
  1128		 * be changed later (NOTE: the bit will be cleared on first vCPU run
  1129		 * if necessary).
  1130		 */
  1131		mutable_mask = (ARMV8_PMU_PMCR_MASK |
  1132				(ARMV8_PMU_PMCR_N_MASK << ARMV8_PMU_PMCR_N_SHIFT));
  1133		val &= mutable_mask;
  1134		val |= (__vcpu_sys_reg(vcpu, r->reg) & ~mutable_mask);
  1135	
  1136		/* The LC bit is RES1 when AArch32 is not supported */
  1137		if (!kvm_supports_32bit_el0())
  1138			val |= ARMV8_PMU_PMCR_LC;
  1139	
  1140		__vcpu_sys_reg(vcpu, r->reg) = val;
  1141		return 0;
  1142	}
  1143	

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel