[PATCH v8 3/6] ARM: dts: Exynos: add CPU OPP and regulator supply property

[ta.omasab@gmail.com (Thomas Abraham)]

Hi Tomasz,

On Tue, Jul 29, 2014 at 4:01 PM, Tomasz Figa <tomasz.figa@gmail.com> wrote:
> Hi Thomas,
>
> Other than the same question about 400 MHz OPP for Exynos4210, I have
> also few more inline.
>
> On 29.07.2014 07:28, Thomas Abraham wrote:
>> For Exynos 4210/5250/5420 based platforms, add CPU operating points and CPU
>> regulator supply properties for migrating from Exynos specific cpufreq driver
>> to using generic cpufreq drivers.
>>
>> Cc: Kukjin Kim <kgene.kim@samsung.com>
>> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
>> ---
>>  arch/arm/boot/dts/exynos4210-origen.dts         |    6 ++++
>>  arch/arm/boot/dts/exynos4210-trats.dts          |    6 ++++
>>  arch/arm/boot/dts/exynos4210-universal_c210.dts |    6 ++++
>>  arch/arm/boot/dts/exynos4210.dtsi               |   12 +++++++
>>  arch/arm/boot/dts/exynos5250-arndale.dts        |    6 ++++
>>  arch/arm/boot/dts/exynos5250-cros-common.dtsi   |    6 ++++
>>  arch/arm/boot/dts/exynos5250-smdk5250.dts       |    6 ++++
>>  arch/arm/boot/dts/exynos5250.dtsi               |   23 ++++++++++++++
>>  arch/arm/boot/dts/exynos5420-smdk5420.dts       |    6 ++++
>
> There are more Exynos5420-based boards supported in mainline. If you do
> not have necessary data and/or hardware to fully enable the new driver
> on them, you should add responsible people on Cc list, so at least they
> know they have one more item on their TODO list. Added them for you.

Thanks!. Will do that next time.

>
>>  arch/arm/boot/dts/exynos5420.dtsi               |   38 +++++++++++++++++++++++
>>  10 files changed, 115 insertions(+)
>
> [snip]
>
>> diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
>> index 492e1ef..876247a 100644
>> --- a/arch/arm/boot/dts/exynos5250.dtsi
>> +++ b/arch/arm/boot/dts/exynos5250.dtsi
>> @@ -63,6 +63,29 @@
>>                       compatible = "arm,cortex-a15";
>>                       reg = <0>;
>>                       clock-frequency = <1700000000>;
>> +
>> +                     clocks = <&clock CLK_ARM_CLK>;
>> +                     clock-names = "cpu";
>> +                     clock-latency = <200000>;
>
> Where does this latency value comes from? How did you calculate it?
>
> For example, on Exynos4210, for all operating points added by your
> patches, the highest PLL locking latency will be 60uS, because the
> highest PDIV value would be 6 and PLL lock time is PDIV*240 ticks of 24
> MHz reference clock.

Since the CPU clock is a composite clock with dividers and muxes, the
latency includes the settling time for these clock blocks as well. I
have not made any measurements of the clock transition latency.

>
>> +
>> +                     operating-points = <
>> +                             1700000 1300000
>> +                             1600000 1250000
>
> [snip]
>
>> diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> index 6052aa9..084e587 100644
>> --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
>> @@ -24,6 +24,12 @@
>>               bootargs = "console=ttySAC2,115200 init=/linuxrc";
>>       };
>>
>> +     cpus {
>
> Is there no regulator for cpu0?

This was a mistake. I did not intend to add regulator for cpu4 as well
but somehow I missed it. I will remove it in the next version.

>
>> +             cpu at 4 {
>> +                     cpu0-supply = <&buck6_reg>;
>> +             };
>> +     };
>> +
>>       fixed-rate-clocks {
>>               oscclk {
>>                       compatible = "samsung,exynos5420-oscclk";
>> diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
>> index cb2b70e..1116d55 100644
>> --- a/arch/arm/boot/dts/exynos5420.dtsi
>> +++ b/arch/arm/boot/dts/exynos5420.dtsi
>
> [snip]
>
>>
>>               cpu1: cpu at 1 {
>> @@ -69,6 +87,7 @@
>>                       reg = <0x1>;
>>                       clock-frequency = <1800000000>;
>>                       cci-control-port = <&cci_control1>;
>> +                     clock-latency = <200000>;
>
> Do you need to specify this property for every CPU or rather just for
> those which have operating points specified?

The big.little cpufreq driver expects each CPU to have the clock
latency specified.

Thanks,
Thomas.

>
> Best regards,
> Tomasz
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pm" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html