From: Alistair Francis <alistair23@gmail.com>
To: Marco Felsch <m.felsch@pengutronix.de>
Cc: Alistair Francis <alistair@alistair23.me>,
linux-kernel@vger.kernel.org, shawnguo@kernel.org,
linux-arm-kernel@lists.infradead.org, linux-imx@nxp.com,
s.hauer@pengutronix.de, robh+dt@kernel.org,
devicetree@vger.kernel.org, krzysztof.kozlowski+dt@linaro.org,
arnd@arndb.de, linux@armlinux.org.uk, jernej.skrabec@gmail.com,
kernel@pengutronix.de, festevam@gmail.com
Subject: Re: [PATCH v2 3/3] ARM: dts: imx7d-remarkable2: Enable the rohm,bd71815
Date: Mon, 9 Jan 2023 22:11:48 +1000 [thread overview]
Message-ID: <CAKmqyKO-Qw3AihUnF7np7_6kr6-ODnXU3aBwph-_9=xSbXRx-Q@mail.gmail.com> (raw)
In-Reply-To: <20221220131715.femjybikqcnm4lyg@pengutronix.de>
On Tue, Dec 20, 2022 at 11:17 PM Marco Felsch <m.felsch@pengutronix.de> wrote:
>
> Hi Alistair,
>
> thanks for your patch, please see below.
>
> On 22-12-20, Alistair Francis wrote:
> > Add support for the rohm,bd71815 power controller controller for the
> > reMarkable 2.
> >
> > Signed-off-by: Alistair Francis <alistair@alistair23.me>
> > ---
> > arch/arm/boot/dts/imx7d-remarkable2.dts | 159 ++++++++++++++++++++++++
> > 1 file changed, 159 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts
> > index a138b292ec6a..4387d30d6180 100644
> > --- a/arch/arm/boot/dts/imx7d-remarkable2.dts
> > +++ b/arch/arm/boot/dts/imx7d-remarkable2.dts
> > @@ -92,6 +92,10 @@ wifi_pwrseq: wifi_pwrseq {
> > };
> > };
> >
> > +&cpu0 {
> > + cpu-supply = <&buck1_reg>;
> > +};
> > +
> > &clks {
> > assigned-clocks = <&clks IMX7D_CLKO2_ROOT_SRC>,
> > <&clks IMX7D_CLKO2_ROOT_DIV>;
> > @@ -119,6 +123,148 @@ wacom_digitizer: digitizer@9 {
> > };
> > };
> >
> > +&i2c2 {
> > + clock-frequency = <100000>;
>
> We can set this now to 400kHz since the driver can handle quirks now
> internal.
After a discussion on the first patch I'm going to leave this as is.
Let me know if you do want me to change it.
>
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + pinctrl-1 = <&pinctrl_i2c2>;
>
> Do we need a "sleep" config here since this will be the same
> configuration as the "default" one.
Nope, dropped.
>
> > + status = "okay";
> > +
> > + bd71815: pmic@4b {
> > + compatible = "rohm,bd71815";
> > + reg = <0x4b>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_bd71815>;
> > + interrupt-parent = <&gpio6>; /* PMIC_INT_B GPIO6_IO16 */
> > + interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
> > + gpio-controller;
> > + clocks = <&clks IMX7D_CLKO2_ROOT_SRC>;
> > + clock-output-names = "bd71815-32k-out";
> > + #clock-cells = <0>;
> > + #gpio-cells = <1>;
> > +
> > + regulators {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + buck1_reg: regulator@0 {
> > + reg = <0>;
> > + regulator-compatible = "buck1";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <2000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <1250>;
> > + };
> > +
> > + buck2_reg: regulator@1 {
> > + reg = <1>;
> > + regulator-compatible = "buck2";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <2000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <1250>;
> > + };
> > +
> > + buck3_reg: regulator@2 {
> > + reg = <2>;
> > + regulator-compatible = "buck3";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <2700000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + buck4_reg: regulator@3 {
> > + reg = <3>;
> > + regulator-compatible = "buck4";
> > + regulator-min-microvolt = <1100000>;
> > + regulator-max-microvolt = <1850000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + buck5_reg: regulator@4 {
> > + reg = <4>;
> > + regulator-compatible = "buck5";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo1_reg: regulator@5 {
> > + reg = <5>;
> > + regulator-compatible = "ldo1";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo2_reg: regulator@6 {
> > + reg = <6>;
> > + regulator-compatible = "ldo2";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo3_reg: regulator@7 {
> > + reg = <7>;
> > + regulator-compatible = "ldo3";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo4_reg: regulator@8 {
> > + reg = <8>;
> > + regulator-compatible = "ldo4";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo5_reg: regulator@9 {
> > + reg = <9>;
> > + regulator-compatible = "ldo5";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + dvref_reg: regulator@a {
> > + reg = <0xa>;
> > + regulator-compatible = "dvref";
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + lpsr_reg: regulator@b {
> > + reg = <0xb>;
> > + regulator-compatible = "lpsr";
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + wled_reg: regulator@c {
> > + reg = <0xc>;
> > + regulator-compatible = "wled";
> > + regulator-min-microamp = <10>;
> > + regulator-max-microamp = <25000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
>
> Note: You have marked all regulators as always on, this is rather
> suboptimal due to power consumption.
Good point. The power consumption is already pretty bad, as mainline
doesn't support the i.MX deep sleep. As I know this works I'd like to
keep it as is. I'll test to see if removing them doesn't break
anything and then send a follow up patch.
Alistair
>
> Regards,
> Marco
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-01-09 12:13 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-12-20 11:29 [PATCH v2 0/3] imx7d-remarkable2: Enable cyttsp5 and rohm,bd71815 Alistair Francis
2022-12-20 11:29 ` [PATCH v2 1/3] ARM: dts: imx7d-remarkable2: Enable the cyttsp5 Alistair Francis
2022-12-20 13:20 ` Marco Felsch
2022-12-20 16:50 ` Ahmad Fatoum
2023-01-06 12:44 ` Alistair Francis
2022-12-20 11:29 ` [PATCH v2 2/3] ARM: imx_v6_v7_defconfig: Enable rohm,bd71815 Alistair Francis
2022-12-20 11:29 ` [PATCH v2 3/3] ARM: dts: imx7d-remarkable2: Enable the rohm,bd71815 Alistair Francis
2022-12-20 13:17 ` Marco Felsch
2023-01-09 12:11 ` Alistair Francis [this message]
2023-01-09 19:13 ` Matti Vaittinen
2023-01-20 9:17 ` Alistair Francis
2023-01-20 14:01 ` Matti Vaittinen
2023-01-21 12:47 ` Alistair Francis
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAKmqyKO-Qw3AihUnF7np7_6kr6-ODnXU3aBwph-_9=xSbXRx-Q@mail.gmail.com' \
--to=alistair23@gmail.com \
--cc=alistair@alistair23.me \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=jernej.skrabec@gmail.com \
--cc=kernel@pengutronix.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=m.felsch@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).