Re: CONFIG_THUMB2_KERNEL=y boot failure after Spectre BHB fixes

From: Ard Biesheuvel <ardb@kernel.org>
To: "Russell King (Oracle)" <linux@armlinux.org.uk>
Cc: Christian Eggers <ceggers@arri.de>,
	Linux ARM <linux-arm-kernel@lists.infradead.org>,
	 Catalin Marinas <catalin.marinas@arm.com>,
	 Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
	llvm@lists.linux.dev, Nathan Chancellor <nathan@kernel.org>
Subject: Re: CONFIG_THUMB2_KERNEL=y boot failure after Spectre BHB fixes
Date: Wed, 30 Mar 2022 18:45:18 +0200	[thread overview]
Message-ID: <CAMj1kXFcrG6TrSU+KcmXCVM7ZWZ2fMjiN8c_dtEwxBugJS_UAQ@mail.gmail.com> (raw)
In-Reply-To: <YkSHJ65qGHO4bonJ@shell.armlinux.org.uk>

On Wed, 30 Mar 2022 at 18:37, Russell King (Oracle)
<linux@armlinux.org.uk> wrote:
>
> On Wed, Mar 30, 2022 at 06:34:25PM +0200, Ard Biesheuvel wrote:
> > On Wed, 30 Mar 2022 at 18:12, Russell King (Oracle)
> > <linux@armlinux.org.uk> wrote:
> > >
> > > On Tue, Mar 22, 2022 at 06:49:17PM +0100, Christian Eggers wrote:
> > > > Hi Nathan, hi Russel,
> > > >
> > > > I stumbled today over the same problem (no output on serial console
> > > > with v5.15.28-rt36). During `git bisect`, I had also some commits
> > > > where a few lines of output were visible.
> > > >
> > > > At commit 8d9d651ff227 ("ARM: use LOADADDR() to get load address of
> > > > sections"), the system boots up to here:
> > > >
> > > > start_kernel()
> > > > +--setup_arch()
> > > >    +--paging_init()
> > > >       +--devicemaps_init()
> > > >          +--eary_trap_init(vectors_base = 0xC7FFE000)
> > > >             +--copy_from_lma(vectors_base = 0xC7FFE000, __vectors_start=0x0, __vectors_end=0x20)
> > > >                +--__memcpy()
> > > >
> > > >                copy_template.S:113
> > > >                ldr8w   r1, r3, r4, r5, r6, r7, r8, ip, lr, abort=20f
> > > >                r1 = 0
> > > >
> > > >
> > > > With the final v5.15.28-rt36 I found out that the system boots fine
> > > > after disabling CONFIG_HARDEN_BRANCH_HISTORY.
> > > >
> > > > Is there anything else I could analyze? My SoC system is a NXP i.MX6LL
> > > > with a ARMv7 core. I have access to a JTAG debugger.
> > >
> > > I think this is already fixed in mainline. Commit:
> > >
> > > 6c7cb60bff7a ("ARM: fix Thumb2 regression")
> > >
> >
> > It's still broken - I sent a couple of patches on Monday, among which
> > one to fix the boot issue with loop8 on Thumb2. The problem is 'b . +
> > 4', which produces a narrow encoding, and so it skips the subsequent
> > subs instruction and loops forever.
>
> And what's the current status? Sorry, I've way too much email from the
> last 2.5 weeks to find it myself.
>

https://lore.kernel.org/linux-arm-kernel/20220328134714.205342-1-ardb@kernel.org/

Nobody bothered to respond yet, I can drop the first two in the patch
tracker if you like.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel