[PATCH renesas/devel 00/13] ARM, arm64: dts: Use R-Car fallback bindings for i2c/iic nodes

[PATCH renesas/devel 00/13] ARM, arm64: dts: Use R-Car fallback bindings for i2c/iic nodes

[Simon Horman]

Hi,

this short series makes use of newly added R-Car fallback bindings in
i2c and iic nodes of the DTs for SoCs where the drivers in question are
already used.

This should have no run-time effect at this time as the current
driver implementations use the same initialisation squeuences for
SoC-specific and R-Car fallback bindings for all the cases covered by
this patch-set.

Based on renesas-devel-20161212-v4.9

Simon Horman (13):
  ARM: dts: r8a7779: Use R-Car Gen 1 fallback binding for i2c nodes
  ARM: dts: r8a7778: Use R-Car Gen 1 fallback binding for i2c nodes
  ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7792: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes
  arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes
  arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes
  ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes
  ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

 arch/arm/boot/dts/r8a7778.dtsi           |  8 ++++----
 arch/arm/boot/dts/r8a7779.dtsi           |  8 ++++----
 arch/arm/boot/dts/r8a7790.dtsi           | 20 ++++++++++++--------
 arch/arm/boot/dts/r8a7791.dtsi           | 21 ++++++++++++---------
 arch/arm/boot/dts/r8a7792.dtsi           | 18 ++++++++++++------
 arch/arm/boot/dts/r8a7793.dtsi           | 21 ++++++++++++---------
 arch/arm/boot/dts/r8a7794.dtsi           | 18 ++++++++++--------
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 21 ++++++++++++++-------
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 21 ++++++++++++++-------
 9 files changed, 94 insertions(+), 62 deletions(-)

-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 01/13] ARM: dts: r8a7779: Use R-Car Gen 1 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 1 fallback binding for i2c nodes in
DT for r8a7779 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7779 and the
fallback binding for R-Car Gen 1.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7779.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi
index 55a7c1e37c57..f47a0edc26d4 100644
--- a/arch/arm/boot/dts/r8a7779.dtsi
+++ b/arch/arm/boot/dts/r8a7779.dtsi
@@ -173,7 +173,7 @@
 	i2c0: i2c at ffc70000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7779";
+		compatible = "renesas,i2c-r8a7779", "renesas,rcar-gen1-i2c";
 		reg = <0xffc70000 0x1000>;
 		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C0>;
@@ -184,7 +184,7 @@
 	i2c1: i2c at ffc71000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7779";
+		compatible = "renesas,i2c-r8a7779", "renesas,rcar-gen1-i2c";
 		reg = <0xffc71000 0x1000>;
 		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C1>;
@@ -195,7 +195,7 @@
 	i2c2: i2c at ffc72000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7779";
+		compatible = "renesas,i2c-r8a7779", "renesas,rcar-gen1-i2c";
 		reg = <0xffc72000 0x1000>;
 		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C2>;
@@ -206,7 +206,7 @@
 	i2c3: i2c at ffc73000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7779";
+		compatible = "renesas,i2c-r8a7779", "renesas,rcar-gen1-i2c";
 		reg = <0xffc73000 0x1000>;
 		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7779_CLK_I2C3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 02/13] ARM: dts: r8a7778: Use R-Car Gen 1 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 1 fallback binding for i2c nodes in
DT for r8a7778 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7778 and the
fallback binding for R-Car Gen 1.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7778.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi
index b0c9674fad17..1e93c94a9eac 100644
--- a/arch/arm/boot/dts/r8a7778.dtsi
+++ b/arch/arm/boot/dts/r8a7778.dtsi
@@ -150,7 +150,7 @@
 	i2c0: i2c at ffc70000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7778";
+		compatible = "renesas,i2c-r8a7778", "renesas,rcar-gen1-i2c";
 		reg = <0xffc70000 0x1000>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C0>;
@@ -161,7 +161,7 @@
 	i2c1: i2c at ffc71000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7778";
+		compatible = "renesas,i2c-r8a7778", "renesas,rcar-gen1-i2c";
 		reg = <0xffc71000 0x1000>;
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C1>;
@@ -172,7 +172,7 @@
 	i2c2: i2c at ffc72000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7778";
+		compatible = "renesas,i2c-r8a7778", "renesas,rcar-gen1-i2c";
 		reg = <0xffc72000 0x1000>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C2>;
@@ -183,7 +183,7 @@
 	i2c3: i2c at ffc73000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7778";
+		compatible = "renesas,i2c-r8a7778", "renesas,rcar-gen1-i2c";
 		reg = <0xffc73000 0x1000>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7778_CLK_I2C3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 03/13] ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7790 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index b7ed7466308b..823ab536175d 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -480,7 +480,7 @@
 	i2c0: i2c at e6508000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7790";
+		compatible = "renesas,i2c-r8a7790", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6508000 0 0x40>;
 		interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_I2C0>;
@@ -492,7 +492,7 @@
 	i2c1: i2c at e6518000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7790";
+		compatible = "renesas,i2c-r8a7790", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6518000 0 0x40>;
 		interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_I2C1>;
@@ -504,7 +504,7 @@
 	i2c2: i2c at e6530000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7790";
+		compatible = "renesas,i2c-r8a7790", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6530000 0 0x40>;
 		interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_I2C2>;
@@ -516,7 +516,7 @@
 	i2c3: i2c at e6540000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7790";
+		compatible = "renesas,i2c-r8a7790", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6540000 0 0x40>;
 		interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_I2C3>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 04/13] ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7791 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 93f446db6a21..48662c13f79a 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -444,7 +444,7 @@
 	i2c0: i2c at e6508000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6508000 0 0x40>;
 		interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C0>;
@@ -456,7 +456,7 @@
 	i2c1: i2c at e6518000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6518000 0 0x40>;
 		interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C1>;
@@ -468,7 +468,7 @@
 	i2c2: i2c at e6530000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6530000 0 0x40>;
 		interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C2>;
@@ -480,7 +480,7 @@
 	i2c3: i2c at e6540000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6540000 0 0x40>;
 		interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C3>;
@@ -492,7 +492,7 @@
 	i2c4: i2c at e6520000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6520000 0 0x40>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C4>;
@@ -505,7 +505,7 @@
 		/* doesn't need pinmux */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7791";
+		compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6528000 0 0x40>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_I2C5>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 05/13] ARM: dts: r8a7792: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7792 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7792 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7792.dtsi | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index c5e834073cb3..222895fc1d0d 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -498,7 +498,8 @@
 
 		/* I2C doesn't need pinmux */
 		i2c0: i2c at e6508000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792",
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C0>;
@@ -510,7 +511,8 @@
 		};
 
 		i2c1: i2c at e6518000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792",
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6518000 0 0x40>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C1>;
@@ -522,7 +524,8 @@
 		};
 
 		i2c2: i2c at e6530000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792",
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6530000 0 0x40>;
 			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C2>;
@@ -534,7 +537,8 @@
 		};
 
 		i2c3: i2c at e6540000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792"
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6540000 0 0x40>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C3>;
@@ -546,7 +550,8 @@
 		};
 
 		i2c4: i2c at e6520000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792"
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6520000 0 0x40>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C4>;
@@ -558,7 +563,8 @@
 		};
 
 		i2c5: i2c at e6528000 {
-			compatible = "renesas,i2c-r8a7792";
+			compatible = "renesas,i2c-r8a7792"
+				     "renesas,rcar-gen2-i2c";
 			reg = <0 0xe6528000 0 0x40>;
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mstp9_clks R8A7792_CLK_I2C5>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 06/13] ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7793 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7793 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 84af1598e292..cbe9ac629693 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -411,7 +411,7 @@
 	i2c0: i2c at e6508000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6508000 0 0x40>;
 		interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C0>;
@@ -423,7 +423,7 @@
 	i2c1: i2c at e6518000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6518000 0 0x40>;
 		interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C1>;
@@ -435,7 +435,7 @@
 	i2c2: i2c at e6530000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6530000 0 0x40>;
 		interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C2>;
@@ -447,7 +447,7 @@
 	i2c3: i2c at e6540000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6540000 0 0x40>;
 		interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C3>;
@@ -459,7 +459,7 @@
 	i2c4: i2c at e6520000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6520000 0 0x40>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C4>;
@@ -472,7 +472,7 @@
 		/* doesn't need pinmux */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,i2c-r8a7793";
+		compatible = "renesas,i2c-r8a7793", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6528000 0 0x40>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_I2C5>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 07/13] ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for i2c nodes in
DT for r8a7794 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7794 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 78e964d5dacb..5fd382a5a7b2 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -611,7 +611,7 @@
 
 	/* The memory map in the User's Manual maps the cores to bus numbers */
 	i2c0: i2c at e6508000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6508000 0 0x40>;
 		interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C0>;
@@ -623,7 +623,7 @@
 	};
 
 	i2c1: i2c at e6518000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6518000 0 0x40>;
 		interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C1>;
@@ -635,7 +635,7 @@
 	};
 
 	i2c2: i2c at e6530000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6530000 0 0x40>;
 		interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C2>;
@@ -647,7 +647,7 @@
 	};
 
 	i2c3: i2c at e6540000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6540000 0 0x40>;
 		interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C3>;
@@ -659,7 +659,7 @@
 	};
 
 	i2c4: i2c at e6520000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6520000 0 0x40>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C4>;
@@ -671,7 +671,7 @@
 	};
 
 	i2c5: i2c at e6528000 {
-		compatible = "renesas,i2c-r8a7794";
+		compatible = "renesas,i2c-r8a7794", "renesas,rcar-gen2-i2c";
 		reg = <0 0xe6528000 0 0x40>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7794_CLK_I2C5>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 08/13] arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7795 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7795 and the
fallback binding for R-Car Gen 3.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index e4110243817d..428056d287a9 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -792,7 +792,8 @@
 		i2c0: i2c at e6500000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6500000 0 0x40>;
 			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 931>;
@@ -806,7 +807,8 @@
 		i2c1: i2c at e6508000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 930>;
@@ -820,7 +822,8 @@
 		i2c2: i2c at e6510000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6510000 0 0x40>;
 			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 929>;
@@ -834,7 +837,8 @@
 		i2c3: i2c at e66d0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d0000 0 0x40>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 928>;
@@ -848,7 +852,8 @@
 		i2c4: i2c at e66d8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d8000 0 0x40>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 927>;
@@ -862,7 +867,8 @@
 		i2c5: i2c at e66e0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e0000 0 0x40>;
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 919>;
@@ -876,7 +882,8 @@
 		i2c6: i2c at e66e8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7795";
+			compatible = "renesas,i2c-r8a7795",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e8000 0 0x40>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 09/13] arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 3 fallback binding for i2c nodes in
DT for r8a7796 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7796 and the
fallback binding for R-Car Gen 3.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 21 ++++++++++++++-------
 1 file changed, 14 insertions(+), 7 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 7bf0f2f6c224..9ebf5c7ab339 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -269,7 +269,8 @@
 		i2c0: i2c at e6500000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6500000 0 0x40>;
 			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 931>;
@@ -284,7 +285,8 @@
 		i2c1: i2c at e6508000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 930>;
@@ -299,7 +301,8 @@
 		i2c2: i2c at e6510000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe6510000 0 0x40>;
 			interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 929>;
@@ -314,7 +317,8 @@
 		i2c3: i2c at e66d0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d0000 0 0x40>;
 			interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 928>;
@@ -328,7 +332,8 @@
 		i2c4: i2c at e66d8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66d8000 0 0x40>;
 			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 927>;
@@ -342,7 +347,8 @@
 		i2c5: i2c at e66e0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e0000 0 0x40>;
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 919>;
@@ -356,7 +362,8 @@
 		i2c6: i2c at e66e8000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "renesas,i2c-r8a7796";
+			compatible = "renesas,i2c-r8a7796",
+				     "renesas,rcar-gen3-i2c";
 			reg = <0 0xe66e8000 0 0x40>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 10/13] ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for iii nodes in
DT for r8a7790 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7790.dtsi | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 823ab536175d..ddf6a8cbe6c1 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -528,7 +528,8 @@
 	iic0: i2c at e6500000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC0>;
@@ -542,7 +543,8 @@
 	iic1: i2c at e6510000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC1>;
@@ -556,7 +558,8 @@
 	iic2: i2c at e6520000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6520000 0 0x425>;
 		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7790_CLK_IIC2>;
@@ -570,7 +573,8 @@
 	iic3: i2c at e60b0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7790_CLK_IICDVFS>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 11/13] ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for iii nodes in
DT for r8a7791 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7791 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7791.dtsi | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 48662c13f79a..01599fe90fc0 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -518,7 +518,8 @@
 		/* doesn't need pinmux */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7791", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7791", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7791_CLK_IICDVFS>;
@@ -532,7 +533,8 @@
 	i2c7: i2c at e6500000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7791", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7791", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_IIC0>;
@@ -546,7 +548,8 @@
 	i2c8: i2c at e6510000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7791", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7791", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7791_CLK_IIC1>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 12/13] ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for iii nodes in
DT for r8a7793 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7793 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7793.dtsi | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index cbe9ac629693..d5114cac656d 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -485,7 +485,8 @@
 		/* doesn't need pinmux */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7793", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7793", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe60b0000 0 0x425>;
 		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp9_clks R8A7793_CLK_IICDVFS>;
@@ -499,7 +500,8 @@
 	i2c7: i2c at e6500000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7793", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7793", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7793_CLK_IIC0>;
@@ -513,7 +515,8 @@
 	i2c8: i2c at e6510000 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "renesas,iic-r8a7793", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7793", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7793_CLK_IIC1>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 13/13] ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

Use recently added R-Car Gen 2 fallback binding for iii nodes in
DT for r8a7794 SoC.

This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7794 and the
fallback binding for R-Car Gen 2.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm/boot/dts/r8a7794.dtsi | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 5fd382a5a7b2..e41f1c9b4a9c 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -683,7 +683,8 @@
 	};
 
 	i2c6: i2c at e6500000 {
-		compatible = "renesas,iic-r8a7794", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7794", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6500000 0 0x425>;
 		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_IIC0>;
@@ -697,7 +698,8 @@
 	};
 
 	i2c7: i2c at e6510000 {
-		compatible = "renesas,iic-r8a7794", "renesas,rmobile-iic";
+		compatible = "renesas,iic-r8a7794", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
 		reg = <0 0xe6510000 0 0x425>;
 		interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp3_clks R8A7794_CLK_IIC1>;
-- 
2.7.0.rc3.207.g0ac5344

[PATCH renesas/devel 10/13] ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes

[Sergei Shtylyov]

Hello!

On 12/12/2016 12:11 PM, Simon Horman wrote:

> Use recently added R-Car Gen 2 fallback binding for iii nodes in

    s/iii/iic/?

> DT for r8a7790 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7790 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[...]

MBR, Sergei

[PATCH renesas/devel 11/13] ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes

[Sergei Shtylyov]

Hello.

On 12/12/2016 12:11 PM, Simon Horman wrote:

> Use recently added R-Car Gen 2 fallback binding for iii nodes in

    s/iii/iic/?

> DT for r8a7791 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7791 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[...]

MBR, Sergei

[PATCH renesas/devel 12/13] ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes

[Sergei Shtylyov]

On 12/12/2016 12:11 PM, Simon Horman wrote:

> Use recently added R-Car Gen 2 fallback binding for iii nodes in

    s/iii/iic/?

> DT for r8a7793 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7793 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[...]

MBR, Sergei

[PATCH renesas/devel 13/13] ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

[Sergei Shtylyov]

On 12/12/2016 12:11 PM, Simon Horman wrote:

> Use recently added R-Car Gen 2 fallback binding for iii nodes in

    s/iii/iic/?

> DT for r8a7794 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7794 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[...]

MBR, Sergei

[PATCH renesas/devel 01/13] ARM: dts: r8a7779: Use R-Car Gen 1 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 1 fallback binding for i2c nodes in
> DT for r8a7779 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7779 and the
> fallback binding for R-Car Gen 1.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 02/13] ARM: dts: r8a7778: Use R-Car Gen 1 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 1 fallback binding for i2c nodes in
> DT for r8a7778 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7778 and the
> fallback binding for R-Car Gen 1.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 03/13] ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for i2c nodes in
> DT for r8a7790 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7790 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 04/13] ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for i2c nodes in
> DT for r8a7791 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7791 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 05/13] ARM: dts: r8a7792: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for i2c nodes in
> DT for r8a7792 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7792 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 07/13] ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for i2c nodes in
> DT for r8a7794 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7794 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 08/13] arm64: dts: r8a7795: Use R-Car Gen 3 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 3 fallback binding for i2c nodes in
> DT for r8a7795 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7795 and the
> fallback binding for R-Car Gen 3.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 09/13] arm64: dts: r8a7796: Use R-Car Gen 3 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 3 fallback binding for i2c nodes in
> DT for r8a7796 SoC.
>
> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7796 and the
> fallback binding for R-Car Gen 3.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 11/13] ARM: dts: r8a7791: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for iii nodes in
> DT for r8a7791 SoC.

iic etc...

> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7791 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 12/13] ARM: dts: r8a7793: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for iii nodes in
> DT for r8a7793 SoC.

iic etc...

> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7793 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 13/13] ARM: dts: r8a7794: Use R-Car Gen 2 fallback binding for i2c nodes

[Geert Uytterhoeven]

On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
<horms+renesas@verge.net.au> wrote:
> Use recently added R-Car Gen 2 fallback binding for iii nodes in
> DT for r8a7794 SoC.

iic etc...

> This has no run-time effect for the current driver as the initialisation
> sequence is the same for the SoC-specific binding for r8a7794 and the
> fallback binding for R-Car Gen 2.
>
> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH renesas/devel 10/13] ARM: dts: r8a7790: Use R-Car Gen 2 fallback binding for i2c nodes

[Simon Horman]

On Mon, Dec 12, 2016 at 01:28:30PM +0300, Sergei Shtylyov wrote:
> Hello!
> 
> On 12/12/2016 12:11 PM, Simon Horman wrote:
> 
> >Use recently added R-Car Gen 2 fallback binding for iii nodes in
> 
>    s/iii/iic/?

Yes, thanks for noticing that.

> >DT for r8a7790 SoC.
> >
> >This has no run-time effect for the current driver as the initialisation
> >sequence is the same for the SoC-specific binding for r8a7790 and the
> >fallback binding for R-Car Gen 2.
> >
> >Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
> [...]
> 
> MBR, Sergei
> 

On Mon, Dec 12, 2016 at 02:42:29PM +0100, Geert Uytterhoeven wrote:
> Hi SImon,
> 
> On Mon, Dec 12, 2016 at 10:11 AM, Simon Horman
> <horms+renesas@verge.net.au> wrote:
> > Use recently added R-Car Gen 2 fallback binding for iii nodes in
> 
> As Sergei already pointed out: s/iii/iic/.
> 
> You may also want to s/i2c/iic/ in the one-line summary, to avoid having
> multiple different patches with the same one-line summary (initially I was a
> bit confused by this, as Gmail grouped them together).

Yes, I meant to differentiate the subjects as you suggest.
I'll fix things up.

> These two comments apply to all iic DT patches in this series.

Got it.