[PATCH 1/8] arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode

[PATCH 1/8] arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode

[Jacopo Mondi]

As the PHY interface installed on the Salvator-X[S] board, provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.

Follow up patches will reset the SoC DTSI to use "rgmii" mode and let
the board file override that.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 arch/arm64/boot/dts/renesas/salvator-common.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index 8e8ec30..c725f9b 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -279,6 +279,7 @@
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
 	phy-handle = <&phy0>;
+	phy-mode = "rgmii-txid";
 	status = "okay";
 
 	phy0: ethernet-phy at 0 {
-- 
2.7.4

[PATCH 1/8] arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> As the PHY interface installed on the Salvator-X[S] board, provides TX
> channel delay, make the "phy-mode" property a board-specific one, meant
> to override the one specified in the SoC DTSI.
>
> Follow up patches will reset the SoC DTSI to use "rgmii" mode and let
> the board file override that.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 4/8] arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"

[Jacopo Mondi]

Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
files override it if the installed PHY layer provides delays for the
RX/TX channels.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a77995.dtsi b/arch/arm64/boot/dts/renesas/r8a77995.dtsi
index cd3c6a3..fc48677 100644
--- a/arch/arm64/boot/dts/renesas/r8a77995.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77995.dtsi
@@ -512,7 +512,7 @@
 			clocks = <&cpg CPG_MOD 812>;
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 812>;
-			phy-mode = "rgmii-txid";
+			phy-mode = "rgmii";
 			iommus = <&ipmmu_ds0 16>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.7.4

[PATCH 4/8] arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii"

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
> files override it if the installed PHY layer provides delays for the
> RX/TX channels.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

But you need a patch to update r8a7795-draak.dtsi first.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 2/8] arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii"

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
> files override it if the installed PHY layer provides delays for the
> RX/TX channels.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

But you need a patch to update ulcb.dtsi first.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 3/8] arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii"

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Set the "phy-mode" property of EtherAVB device to "rgmii" and let board
> files override it if the installed PHY layer provides delays for the
> RX/TX channels.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

But you need a patch to update ulcb.dtsi first.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 5/8] dt-bindings: iommu/ipmmu-vmsa: Add R-Car M3-N (R8A77965)

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Add Renesas R-Car M3-N (R8A77965) compat string to IPMMU DT bindings
> documentation.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 5/8] dt-bindings: iommu/ipmmu-vmsa: Add R-Car M3-N (R8A77965)

[Rob Herring]

On Mon, Feb 26, 2018 at 06:57:13PM +0100, Jacopo Mondi wrote:
> Add Renesas R-Car M3-N (R8A77965) compat string to IPMMU DT bindings
> documentation.
> 
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> ---
>  Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt | 1 +
>  1 file changed, 1 insertion(+)

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH 6/8] iommu/ipmmu-vmsa: Hook up R8A77965 DT matching code

[Geert Uytterhoeven]

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Add support for R-Car M3-N (R8A77965) SoC IPMMUs.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 8/8] arm64: dts: renesas: r8a77965: Add EtherAVB device node

[Geert Uytterhoeven]

Hi Jacopo,

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> Populate the ethernet at e6800000 device node to enable Ethernet interface
> for R-Car M3-N (R8A77965) SoC.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
>
> ---
> v1 -> v2:
> - Replace ALWAYS_ON power area identifier with numeric constant

And you added the iommus property, which I wouldn't bother doing at this
early stage.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 0/8] R-Car M3-N: Enable EtherAVB device node

[Geert Uytterhoeven]

Hi Jacopo,

On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
>   as discussed with you Sergei and Geert, in order to enable EtherAVB for
> R8A77965 we first wanted to make the phy-mode "rgmii-txid" a board specific
> property for all other SoCs.

Thanks for your series!

> This series adds  the phy-mode property to salvator-common.dtsi and reset the
> one for R8A77965/R8A7796/R8A77995 to "rgmii".

I forgot that r8a7795.dtsi and r8a7796.dtsi are used for the ULCB boards, too.
So to avoid regressions, you need to make a similar change to ulcb.dtsi like you
made for salvator-common.dtsi.

In addition, r8a77995.dtsi is only used for the Draak board.
So you have to update r8a7795-draak.dtsi first, too.

> Then, in order to enable EtherAVB for R-Car M3-N, iommu nodes had to be added
> as they are referenced by the "avb" device node (CC the iommu list for the
> series for that reason).

I don't think we need the iommu properties and nodes at this early stage.
Ethernet works fine without them. Simon, do you agree?

P.S. scripts/dtc/dtx_diff is a great tool to compare DTBs before and after your
      changes. It would have revealed the changes for ULCB and Draak.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

[PATCH 0/8] R-Car M3-N: Enable EtherAVB device node

[jacopo mondi]

Hi Geert,

On Mon, Feb 26, 2018 at 07:28:47PM +0100, Geert Uytterhoeven wrote:
> Hi Jacopo,
>
> On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> >   as discussed with you Sergei and Geert, in order to enable EtherAVB for
> > R8A77965 we first wanted to make the phy-mode "rgmii-txid" a board specific
> > property for all other SoCs.
>
> Thanks for your series!
>
> > This series adds  the phy-mode property to salvator-common.dtsi and reset the
> > one for R8A77965/R8A7796/R8A77995 to "rgmii".
>
> I forgot that r8a7795.dtsi and r8a7796.dtsi are used for the ULCB boards, too.
> So to avoid regressions, you need to make a similar change to ulcb.dtsi like you
> made for salvator-common.dtsi.
>
> In addition, r8a77995.dtsi is only used for the Draak board.
> So you have to update r8a7795-draak.dtsi first, too.

Of course! I forgot about ULCB (and had a patch for Draak I lost while
rebasing :/ )
>
> > Then, in order to enable EtherAVB for R-Car M3-N, iommu nodes had to be added
> > as they are referenced by the "avb" device node (CC the iommu list for the
> > series for that reason).
>
> I don't think we need the iommu properties and nodes at this early stage.
> Ethernet works fine without them. Simon, do you agree?

I'll wait for Simon reply and then resend, possibly without iommu and
ULCB and Draak patches!

Thanks
   j

>
> P.S. scripts/dtc/dtx_diff is a great tool to compare DTBs before and after your
>       changes. It would have revealed the changes for ULCB and Draak.
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds

[PATCH 0/8] R-Car M3-N: Enable EtherAVB device node

[Simon Horman]

On Tue, Feb 27, 2018 at 09:28:38AM +0100, jacopo mondi wrote:
> Hi Geert,
> 
> On Mon, Feb 26, 2018 at 07:28:47PM +0100, Geert Uytterhoeven wrote:
> > Hi Jacopo,
> >
> > On Mon, Feb 26, 2018 at 6:57 PM, Jacopo Mondi <jacopo+renesas@jmondi.org> wrote:
> > >   as discussed with you Sergei and Geert, in order to enable EtherAVB for
> > > R8A77965 we first wanted to make the phy-mode "rgmii-txid" a board specific
> > > property for all other SoCs.
> >
> > Thanks for your series!
> >
> > > This series adds  the phy-mode property to salvator-common.dtsi and reset the
> > > one for R8A77965/R8A7796/R8A77995 to "rgmii".
> >
> > I forgot that r8a7795.dtsi and r8a7796.dtsi are used for the ULCB boards, too.
> > So to avoid regressions, you need to make a similar change to ulcb.dtsi like you
> > made for salvator-common.dtsi.
> >
> > In addition, r8a77995.dtsi is only used for the Draak board.
> > So you have to update r8a7795-draak.dtsi first, too.
> 
> Of course! I forgot about ULCB (and had a patch for Draak I lost while
> rebasing :/ )
> >
> > > Then, in order to enable EtherAVB for R-Car M3-N, iommu nodes had to be added
> > > as they are referenced by the "avb" device node (CC the iommu list for the
> > > series for that reason).
> >
> > I don't think we need the iommu properties and nodes at this early stage.
> > Ethernet works fine without them. Simon, do you agree?
> 
> I'll wait for Simon reply and then resend, possibly without iommu and
> ULCB and Draak patches!

I don't feel strongly about this but I don't think iommu is a strict
dependency of enabling Ethernet and I think its good not to include extra
dependencies - if it was me I'd try to get Ethernet accepted then follow-up
on iommu.