[PATCH] ARM: nomadik: fix up SD/MMC DT settings

[ulf.hansson@linaro.org (Ulf Hansson)]

On 1 February 2016 at 14:18, Linus Walleij <linus.walleij@linaro.org> wrote:
> The DTSI file for the Nomadik does not properly specify how the
> PL180 levelshifter is connected: the Nomadik actually needs all
> the five st,sig-dir-* flags set to properly control all lines out.
>
> Further this board supports full power cycling of the card, and
> since this variant has no hardware clock gating, it needs a
> ridiculously low frequency setting to keep up with the ever
> overflowing FIFO.
>
> The pin configuration set-up is a bit of a mystery, because of
> course these pins are a mix of inputs and outputs. However the
> reference implementation sets all pins to "output" with
> unspecified initial value, so let's do that here as well.
>
> Cc: stable at vger.kernel.org
> Cc: Ulf Hansson <ulf.hansson@linaro.org>

Looks good to me!

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>

> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ARM SoC folks: this fixes the non-working SD/MMC card on the
> Nomadik please apply this directly for fixes if Ulf is OK with
> it.
> ---
>  arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 37 ++++++++++++++++--------------
>  1 file changed, 20 insertions(+), 17 deletions(-)
>
> diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> index 50c256f0fd98..b1707f6217bf 100644
> --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi
> @@ -128,22 +128,14 @@
>                         };
>                         mmcsd_default_mode: mmcsd_default {
>                                 mmcsd_default_cfg1 {
> -                                       /* MCCLK */
> -                                       pins = "GPIO8_B10";
> -                                       ste,output = <0>;
> -                               };
> -                               mmcsd_default_cfg2 {
> -                                       /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
> -                                       pins = "GPIO10_C11", "GPIO15_A12",
> -                                       "GPIO16_C13", "GPIO23_D15";
> -                                       ste,output = <1>;
> -                               };
> -                               mmcsd_default_cfg3 {
> -                                       /* MCCMD, MCDAT3-0, MCMSFBCLK */
> -                                       pins = "GPIO9_A10", "GPIO11_B11",
> -                                       "GPIO12_A11", "GPIO13_C12",
> -                                       "GPIO14_B12", "GPIO24_C15";
> -                                       ste,input = <1>;
> +                                       /*
> +                                        * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
> +                                        * MCCMD, MCDAT3-0, MCMSFBCLK
> +                                        */
> +                                       pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
> +                                              "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
> +                                              "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
> +                                       ste,output = <2>;
>                                 };
>                         };
>                 };
> @@ -803,10 +795,21 @@
>                         clock-names = "mclk", "apb_pclk";
>                         interrupt-parent = <&vica>;
>                         interrupts = <22>;
> -                       max-frequency = <48000000>;
> +                       max-frequency = <400000>;
>                         bus-width = <4>;
>                         cap-mmc-highspeed;
>                         cap-sd-highspeed;
> +                       full-pwr-cycle;
> +                       /*
> +                        * The STw4811 circuit used with the Nomadik strictly
> +                        * requires that all of these signal direction pins be
> +                        * routed and used for its 4-bit levelshifter.
> +                        */
> +                       st,sig-dir-dat0;
> +                       st,sig-dir-dat2;
> +                       st,sig-dir-dat31;
> +                       st,sig-dir-cmd;
> +                       st,sig-pin-fbclk;
>                         pinctrl-names = "default";
>                         pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
>                         vmmc-supply = <&vmmc_regulator>;
> --
> 2.4.3
>