[PATCH v5 0/9] Add sd/emmc support for stih407 family silicon

[ulf.hansson@linaro.org (Ulf Hansson)]

On 30 April 2015 at 10:28, Maxime Coquelin <maxime.coquelin@st.com> wrote:
> Hi Ulf,
>
>
> On 04/10/2015 01:06 PM, Ulf Hansson wrote:
>>
>> On 10 April 2015 at 11:40, Peter Griffin <peter.griffin@linaro.org> wrote:
>>>
>>> Hi,
>>>
>>> This series adds sd/emmc support to the sdhci-st.c driver for stih407
>>> family silicon. The changes mainly involve configuring some extra glue
>>> registers in the flashSS which configure the Arasan controller.
>>>
>>> This series also adds support for UHS modes for eMMC. To allow
>>> UHS HS200/SD104 modes to function correctly, due to the
>>> tight timing constriants, support for delay management is also added.
>>> Two types of delay management are supported, static delay management and
>>> dynamic delay management, this delay management is only available
>>> on eMMC pads on stih410 and later silicon.
>>>
>>> This series has been tested with stih410-b2120 revd on eMMC and sd, at
>>> various clock speeds. As part of this testing a bug was also found in the
>>> upstream flexgen clock set_rate implementation (now fixed upstream).
>>>
>>>      max-frequency = 200Mhz
>>>      /dev/mmcblk0p1:
>>>       Timing buffered disk reads: 270 MB in  3.02 seconds =  89.54 MB/sec
>>>
>>>      max-frequency = 100Mhz
>>>      root at debian-armhf:~# hdparm -t /dev/mmcblk0p1
>>>      /dev/mmcblk0p1:
>>>       Timing buffered disk reads: 210 MB in  3.00 seconds =  70.00 MB/sec
>>>
>>>      max-frequency = 50Mhz
>>>      root at debian-armhf:~# hdparm -t /dev/mmcblk0p1
>>>      /dev/mmcblk0p1:
>>>       Timing buffered disk reads: 118 MB in  3.00 seconds =  39.28 MB/sec
>>>
>>> It has also been tested on stih416-b2020 to ensure we have caused no
>>> regressions. Finally the dt documentation has been updated to reflect
>>> the changes in the driver code. Intrestingly it seems we are the first
>>> upstream platform to be using some of the uhs bindings such as
>>> sd-uhs-sdr104.
>>>
>>> Changes since v4:
>>>   - Fixup typo (Pete)
>>>
>>> Changes since v3:
>>>   - Rebased on Ulf's mmc next branch (rc5 based) (Ulf)
>>>
>>> Changes since v2:
>>>   - Some whitespace fixups (Max)
>>>   - if (!ioaddr) suggestion (Max)
>>>   - Add stih418-b2199 suport (Max)
>>>   - Stih410 to STiH410 fixes (Max)
>>>   - rebased on v4.0-rc6 (Pete)
>>>
>>> Changes since v1:
>>>   - Partition the changes into smaller patches to aid review process
>>> (Ulf)
>>>
>>> Peter Griffin (9):
>>>    mmc: sdhci-st: Add macros for register offsets and bitfields for mmcss
>>>      glue regs
>>>    mmc: sdhci-st: Add support for de-asserting reset signal and top regs
>>>      resource
>>>    mmc: sdhci-st: Add delay management functions for top registers
>>>      (eMMC).
>>>    mmc: sdhci-st: Add st_mmcss_cconfig function to configure mmcss glue
>>>      registers.
>>>    mmc: sdhci-st: Add sdhci_st_set_uhs_signaling function.
>>>    mmc: sdhci-st: Update the quirks for this controller.
>>>    mmc: sdhci-st: Update ST SDHCI binding documentation.
>>>    ARM: STi: DT: STiH407: Add dt nodes for sdhci and emmc.
>>>    ARM: STi: DT: STiH418: Add dt nodes for sdhci and emmc.
>>>
>>>   Documentation/devicetree/bindings/mmc/sdhci-st.txt | 100 +++++-
>>>   arch/arm/boot/dts/stih407-family.dtsi              |  30 ++
>>>   arch/arm/boot/dts/stih410-b2120.dts                |  10 +
>>>   arch/arm/boot/dts/stih418-b2199.dts                |  12 +
>>>   arch/arm/boot/dts/stihxxx-b2120.dtsi               |   8 +
>>>   drivers/mmc/host/sdhci-st.c                        | 354
>>> ++++++++++++++++++++-
>>>   6 files changed, 500 insertions(+), 14 deletions(-)
>>>
>>> --
>>> 1.9.1
>>>
>> Thanks! Applied.
>
> Do you confirm you didn't applied the DT patches?
>

Correct. Sorry if that was unclear.

Kind regards
Uffe