From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Nishanth Menon <nm@ti.com>, Benoit Parrot <bparrot@ti.com>,
devicetree@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
linux-arm-kernel@lists.infradead.org,
Tony Lindgren <tony@atomide.com>, Pratyush Yadav <p.yadav@ti.com>
Subject: Re: [PATCH 2/2] arm64: dts: ti: k3-am654-base-board: remove ov5640
Date: Mon, 12 Apr 2021 11:00:59 +0300 [thread overview]
Message-ID: <YHP+O3HPCCWOQRb0@pendragon.ideasonboard.com> (raw)
In-Reply-To: <20210412075306.102884-2-tomi.valkeinen@ideasonboard.com>
Hi Tomi,
Thank you for the patch.
On Mon, Apr 12, 2021 at 10:53:06AM +0300, Tomi Valkeinen wrote:
> AM654 EVM boards are not shipped with OV5640 sensor module, it is a
> separate purchase. OV5640 module is also just one of the possible
> sensors or capture boards you can connect.
>
> However, for some reason, OV5640 has been added to the board dts file,
> making it cumbersome to use other sensors.
>
> Remove the OV5640 from the dts file so that it is easy to use other
> sensors via DT overlays.
>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
> ---
> .../arm64/boot/dts/ti/k3-am654-base-board.dts | 27 -------------------
> 1 file changed, 27 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index fe3043943906..76358b4944e1 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -85,12 +85,6 @@ sw6 {
> gpios = <&wkup_gpio0 27 GPIO_ACTIVE_LOW>;
> };
> };
> -
> - clk_ov5640_fixed: clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <24000000>;
> - };
> };
>
> &wkup_pmx0 {
> @@ -288,22 +282,6 @@ &main_i2c1 {
> pinctrl-0 = <&main_i2c1_pins_default>;
> clock-frequency = <400000>;
>
> - ov5640: camera@3c {
> - compatible = "ovti,ov5640";
> - reg = <0x3c>;
> -
> - clocks = <&clk_ov5640_fixed>;
> - clock-names = "xclk";
> -
> - port {
> - csi2_cam0: endpoint {
> - remote-endpoint = <&csi2_phy0>;
> - clock-lanes = <0>;
> - data-lanes = <1 2>;
> - };
> - };
> - };
> -
> };
As for patch 1/2, you could drop the two nodes completely. Same question
about overlay availability.
>
> &main_i2c2 {
> @@ -497,11 +475,6 @@ flash@0{
> };
>
> &csi2_0 {
> - csi2_phy0: endpoint {
> - remote-endpoint = <&csi2_cam0>;
> - clock-lanes = <0>;
> - data-lanes = <1 2>;
> - };
> };
>
> &mcu_cpsw {
--
Regards,
Laurent Pinchart
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-04-12 8:03 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-12 7:53 [PATCH 1/2] ARM: dts: dra76-evm: remove ov5640 Tomi Valkeinen
2021-04-12 7:53 ` [PATCH 2/2] arm64: dts: ti: k3-am654-base-board: " Tomi Valkeinen
2021-04-12 8:00 ` Laurent Pinchart [this message]
2021-04-12 8:36 ` Pratyush Yadav
2021-04-12 9:15 ` Tomi Valkeinen
2021-04-12 9:26 ` Vignesh Raghavendra
2021-04-12 14:03 ` Nishanth Menon
2021-04-12 8:00 ` [PATCH 1/2] ARM: dts: dra76-evm: " Laurent Pinchart
2021-04-12 8:26 ` Tomi Valkeinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YHP+O3HPCCWOQRb0@pendragon.ideasonboard.com \
--to=laurent.pinchart@ideasonboard.com \
--cc=bparrot@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=nm@ti.com \
--cc=p.yadav@ti.com \
--cc=robh+dt@kernel.org \
--cc=tomi.valkeinen@ideasonboard.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).