* rk3399-roc-pc does not boot
@ 2022-06-17 9:06 Corentin Labbe
2022-06-17 9:58 ` Robin Murphy
0 siblings, 1 reply; 7+ messages in thread
From: Corentin Labbe @ 2022-06-17 9:06 UTC (permalink / raw)
To: heiko, robh+dt, krzysztof.kozlowski+dt, linux-rockchip,
linux-arm-kernel
Cc: linux-kernel
Hello
I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
It boot normally up to starting init but it stucks shorty after.
It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
When disabling CONFIG_USB, the board boots successfully.
In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
Can it be possible that the problem was that the power port being disabled ?
dmesg of a bad boot:
[ 0.000000] Linux version 5.19.0-rc2-next-20220614-00140-gf1da72cc3751 (compile@Red) (aarch64-unknown-linux-gnu-gcc (Gentoo 11.3.0 p4) 11.3.0, GNU ld (Gentoo 2.37_p1 p2) 2.37) #194 SMP PREEMPT Fri Jun 17 08:42:30 CEST 2022
[ 0.000000] Machine model: Firefly ROC-RK3399-PC Board
[ 0.000000] efi: UEFI not found.
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0xf77ddb40-0xf77dffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
[ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
[ 0.000000] cma: Reserved 32 MiB at 0x00000000ee000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 20 pages/cpu s44584 r8192 d29144 u81920
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] Fallback order for Node 0: 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: console=ttyS2,1500000n8 root=/dev/ram0 ip=dhcp ip=dhcp
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 3883504K/4061184K available (16064K kernel code, 3398K rwdata, 9040K rodata, 6976K init, 581K bss, 144912K reserved, 32768K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @480000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x0000000000440000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000000450000
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.004263] Console: colour dummy device 80x25
[ 0.004389] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.004409] pid_max: default: 32768 minimum: 301
[ 0.004533] LSM: Security Framework initializing
[ 0.004698] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.004734] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.007236] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.007256] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.007383] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.007640] rcu: Hierarchical SRCU implementation.
[ 0.008046] Platform MSI: interrupt-controller@fee20000 domain created
[ 0.008547] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.008870] fsl-mc MSI: interrupt-controller@fee20000 domain created
[ 0.015302] EFI services will not be available.
[ 0.015877] smp: Bringing up secondary CPUs ...
[ 0.016666] Detected VIPT I-cache on CPU1
[ 0.016715] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.016737] GICv3: CPU1: using allocated LPI pending table @0x0000000000460000
[ 0.016799] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.017650] Detected VIPT I-cache on CPU2
[ 0.017688] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.017706] GICv3: CPU2: using allocated LPI pending table @0x0000000000470000
[ 0.017744] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.018528] Detected VIPT I-cache on CPU3
[ 0.018563] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.018581] GICv3: CPU3: using allocated LPI pending table @0x0000000000500000
[ 0.018617] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.019430] CPU features: detected: Spectre-v2
[ 0.019441] CPU features: detected: Spectre-v3a
[ 0.019449] CPU features: detected: Spectre-BHB
[ 0.019460] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.019465] Detected PIPT I-cache on CPU4
[ 0.019500] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.019518] GICv3: CPU4: using allocated LPI pending table @0x0000000000510000
[ 0.019558] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[ 0.020382] Detected PIPT I-cache on CPU5
[ 0.020414] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.020430] GICv3: CPU5: using allocated LPI pending table @0x0000000000520000
[ 0.020462] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[ 0.020577] smp: Brought up 1 node, 6 CPUs
[ 0.020589] SMP: Total of 6 processors activated.
[ 0.020596] CPU features: detected: 32-bit EL0 Support
[ 0.020600] CPU features: detected: 32-bit EL1 Support
[ 0.020607] CPU features: detected: CRC32 instructions
[ 0.021930] CPU: All CPU(s) started at EL2
[ 0.022004] alternatives: patching kernel code
[ 0.025032] devtmpfs: initialized
[ 0.035691] KASLR disabled due to lack of seed
[ 0.035877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.035895] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 0.036700] pinctrl core: initialized pinctrl subsystem
[ 0.037742] DMI not present or invalid.
[ 0.038508] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.040015] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 0.040446] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.040790] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.040849] audit: initializing netlink subsys (disabled)
[ 0.041054] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[ 0.042537] thermal_sys: Registered thermal governor 'step_wise'
[ 0.042544] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.042968] cpuidle: using governor menu
[ 0.043150] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.043333] ASID allocator initialised with 65536 entries
[ 0.043342] HugeTLB: can optimize 4095 vmemmap pages for hugepages-1048576kB
[ 0.043349] HugeTLB: can optimize 127 vmemmap pages for hugepages-32768kB
[ 0.043354] HugeTLB: can optimize 7 vmemmap pages for hugepages-2048kB
[ 0.043359] HugeTLB: can optimize 0 vmemmap pages for hugepages-64kB
[ 0.045524] Serial: AMBA PL011 UART driver
[ 0.076636] platform ff770000.syscon:phy@f780: Fixing up cyclic dependency with fe330000.mmc
[ 0.084251] platform ff940000.hdmi: Fixing up cyclic dependency with ff8f0000.vop
[ 0.084309] platform ff940000.hdmi: Fixing up cyclic dependency with ff900000.vop
[ 0.092195] rockchip-gpio ff720000.gpio: probed /pinctrl/gpio@ff720000
[ 0.093023] rockchip-gpio ff730000.gpio: probed /pinctrl/gpio@ff730000
[ 0.093575] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000
[ 0.094176] rockchip-gpio ff788000.gpio: probed /pinctrl/gpio@ff788000
[ 0.094721] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000
[ 0.115188] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.115199] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.115206] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.115212] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.117251] ACPI: Interpreter disabled.
[ 0.122071] iommu: Default domain type: Translated
[ 0.122078] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.122353] SCSI subsystem initialized
[ 0.122741] usbcore: registered new interface driver usbfs
[ 0.122785] usbcore: registered new interface driver hub
[ 0.122819] usbcore: registered new device driver usb
[ 0.124733] pps_core: LinuxPPS API ver. 1 registered
[ 0.124738] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.124752] PTP clock support registered
[ 0.124964] EDAC MC: Ver: 3.0.0
[ 0.127627] FPGA manager framework
[ 0.127725] Advanced Linux Sound Architecture Driver Initialized.
[ 0.128434] vgaarb: loaded
[ 0.128760] clocksource: Switched to clocksource arch_sys_counter
[ 0.129141] VFS: Disk quotas dquot_6.6.0
[ 0.129195] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.129399] pnp: PnP ACPI: disabled
[ 0.138807] NET: Registered PF_INET protocol family
[ 0.139074] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.143430] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.143539] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.143564] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.143947] TCP bind bhash tables hash table entries: 32768 (order: 7, 786432 bytes, linear)
[ 0.144919] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.145036] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.145179] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 0.145462] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.145924] RPC: Registered named UNIX socket transport module.
[ 0.145931] RPC: Registered udp transport module.
[ 0.145934] RPC: Registered tcp transport module.
[ 0.145938] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.145947] PCI: CLS 0 bytes, default 64
[ 0.146292] Trying to unpack rootfs image as initramfs...
[ 0.146985] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.147416] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.148134] kvm [1]: IPA Size Limit: 40 bits
[ 0.150097] kvm [1]: vgic-v2@fff20000
[ 0.150127] kvm [1]: GIC system register CPU interface enabled
[ 0.150356] kvm [1]: vgic interrupt IRQ18
[ 0.150571] kvm [1]: Hyp mode initialized successfully
[ 0.152166] Initialise system trusted keyrings
[ 0.152432] workingset: timestamp_bits=42 max_order=20 bucket_order=0
[ 0.159762] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.160556] NFS: Registering the id_resolver key type
[ 0.160603] Key type id_resolver registered
[ 0.160607] Key type id_legacy registered
[ 0.160691] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.160697] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.160959] 9p: Installing v9fs 9p2000 file system support
[ 0.225217] Key type asymmetric registered
[ 0.22
[ 2.398776] Freeing initrd memory: 30120K
[ 2.442065] tun: Universal TUN/TAP device driver, 1.6
[ 2.443653] thunder_xcv, ver 1.0
[ 2.443695] thunder_bgx, ver 1.0
[ 2.443729] nicpf, ver 1.0
[ 2.446229] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 2.446238] hns3: Copyright (c) 2017 Huawei Corporation.
[ 2.446298] hclge is initializing
[ 2.446316] e1000: Intel(R) PRO/1000 Network Driver
[ 2.446320] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 2.446359] e1000e: Intel(R) PRO/1000 Network Driver
[ 2.446362] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 2.446400] igb: Intel(R) Gigabit Ethernet Network Driver
[ 2.446404] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 2.446443] igbvf: Intel(R) Gigabit Virtual Function Network Driver
[ 2.446447] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 2.447097] sky2: driver version 1.30
[ 2.449286] VFIO - User Level meta-driver version: 0.3
[ 2.457362] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.457373] ehci-pci: EHCI PCI platform driver
[ 2.457409] ehci-platform: EHCI generic platform driver
[ 2.457678] ehci-orion: EHCI orion driver
[ 2.457883] ehci-exynos: EHCI Exynos driver
[ 2.458062] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.458087] ohci-pci: OHCI PCI platform driver
[ 2.458133] ohci-platform: OHCI generic platform driver
[ 2.458377] ohci-exynos: OHCI Exynos driver
[ 2.459499] usbcore: registered new interface driver usb-storage
[ 2.464840] i2c_dev: i2c /dev entries driver
[ 2.483646] dw_wdt ff848000.watchdog: No valid TOPs array specified
[ 2.489132] sdhci: Secure Digital Host Controller Interface driver
[ 2.489141] sdhci: Copyright(c) Pierre Ossman
[ 2.490655] Synopsys Designware Multimedia Card Interface Driver
[ 2.492809] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.496050] mmc1: CQHCI version 5.10
[ 2.498229] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.500422] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 2.501687] usbcore: registered new interface driver usbhid
[ 2.501694] usbhid: USB HID core driver
[ 2.513858] NET: Registered PF_PACKET protocol family
[ 2.514032] 9pnet: Installing 9P2000 support
[ 2.514102] Key type dns_resolver registered
[ 2.514738] registered taskstats version 1
[ 2.514757] Loading compiled-in X.509 certificates
[ 2.520908] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.567578] rockchip-usb2phy ff770000.syscon:usb2phy@e450: failed to create phy
[ 2.572233] rockchip-usb2phy ff770000.syscon:usb2phy@e460: failed to create phy
[ 2.596788] rk808 0-001b: chip id: 0x0
[ 2.603697] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 2.603742] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 2.624666] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[ 2.629750] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[ 2.636958] cpu cpu0: EM: created perf domain
[ 2.638707] cpu cpu4: EM: created perf domain
[ 2.662475] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.662502] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 2.662622] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 2.662646] xhci-hcd xhci-hcd.0.auto: irq 67, io mem 0xfe800000
[ 2.662788] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.662796] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 2.662805] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 2.663832] hub 1-0:1.0: USB hub found
[ 2.663862] hub 1-0:1.0: 1 port detected
[ 2.664123] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.664619] hub 2-0:1.0: USB hub found
[ 2.664640] hub 2-0:1.0: 1 port detected
[ 2.674843] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.674869] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 2.674997] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 2.675051] xhci-hcd xhci-hcd.1.auto: irq 68, io mem 0xfe900000
[ 2.675201] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.675211] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 2.675221] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 2.675766] hub 3-0:1.0: USB hub found
[ 2.675791] hub 3-0:1.0: 1 port detected
[ 2.676072] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.676442] hub 4-0:1.0: USB hub found
[ 2.676462] hub 4-0:1.0: 1 port detected
[ 2.682696] ehci-platform fe380000.usb: EHCI Host Controller
[ 2.682721] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
[ 2.682835] ehci-platform fe380000.usb: irq 69, io mem 0xfe380000
[ 2.684546] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[ 2.684568] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
[ 2.684689] ohci-platform fe3a0000.usb: irq 71, io mem 0xfe3a0000
[ 2.684773] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 2.684788] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 7
[ 2.684863] ehci-platform fe3c0000.usb: irq 70, io mem 0xfe3c0000
[ 2.686659] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 2.686682] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 8
[ 2.686813] ohci-platform fe3e0000.usb: irq 72, io mem 0xfe3e0000
[ 2.688941] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 2.689400] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
[ 2.689434] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
[ 2.689442] dwmmc_rockchip fe320000.mmc: Version ID is 270a
[ 2.689483] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 74,32 bit host data width,256 deep fifo
[ 2.689827] dwmmc_rockchip fe320000.mmc: Got CD GPIO
[ 2.700909] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[ 2.701762] hub 5-0:1.0: USB hub found
[ 2.701796] hub 5-0:1.0: 1 port detected
[ 2.703670] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 2.716867] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 2.717615] hub 7-0:1.0: USB hub found
[ 2.717649] hub 7-0:1.0: 1 port detected
[ 2.749885] hub 8-0:1.0: USB hub found
[ 2.749935] hub 8-0:1.0: 1 port detected
[ 2.751419] hub 6-0:1.0: USB hub found
[ 2.751471] hub 6-0:1.0: 1 port detected
[ 2.772382] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
[ 2.973076] usb 7-1: new high-speed USB device number 2 using ehci-platform
[ 3.005758] dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 136
[ 3.005789] mmc0: new ultra high speed SDR50 SDHC card at address 0007
[ 3.006862] mmcblk0: mmc0:0007 SD4GB 3.71 GiB
[ 3.009227] mmcblk0: p1 p2
[ 3.132986] hub 7-1:1.0: USB hub found
[ 3.133339] hub 7-1:1.0: 4 ports detected
[ 15.042378] ALSA device list:
[ 15.042404] No soundcards found.
[ 15.042770] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
[ 15.047594] Freeing unused kernel memory: 6976K
[ 15.047708] Run /init as init process
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: [ 15.173509] udevd[180]: starting version 3.2.10
[ 33.092753] random: crng init done
[ 33.097189] udevd[181]: starting eudev-3.2.10
[ 33.270362] pwm-backlight backlight: supply power not found, using dummy regulator
[ 33.277620] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[ 33.277630] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[ 33.277718] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[ 33.281235] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[ 33.281246] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[ 33.281250] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[ 33.281259] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[ 33.281290] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[ 33.281293] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[ 33.284736] rockchip-vop ff8f0000.vop: Adding to iommu group 2
[ 33.285547] rockchip-vop ff900000.vop: Adding to iommu group 3
[ 33.286307] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[ 33.286461] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[ 33.286467] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
[ 33.286470] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[ 33.286473] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[ 33.286475] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[ 33.286478] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[ 33.286480] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[ 33.286530] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[ 33.286533] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[ 33.286535] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 33.287020] input: adc-keys as /devices/platform/adc-keys/input/input1
[ 33.287462] OF: graph: no port node found in /i2c@ff160000/usb-typec@22
[ 33.301175] mc: Linux media interface: v0.10
[ 33.304453] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops [rockchipdrm])
[ 33.304557] [drm] unsupported AFBC format[3231564e]
[ 33.306210] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops [rockchipdrm])
[ 33.306357] dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
[ 33.306830] videodev: Linux video capture interface: v2.00
[ 33.308965] dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
[ 33.309136] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 33.312522] OF: graph: no port node found in /i2c@ff3d0000/usb-typec@22
[ 33.315768] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm])
[ 33.317635] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
[ 33.317788] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
[ 33.317853] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 33.317905] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[ 33.320726] hantro-vpu ff650000.video-codec: Adding to iommu group 0
[ 33.321444] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video0
[ 33.321556] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video1
[ 33.326240] rk808-rtc rk808-rtc: registered as rtc0
[ 33.326745] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:51:21 UTC (1358499081)
Regards
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 9:06 rk3399-roc-pc does not boot Corentin Labbe
@ 2022-06-17 9:58 ` Robin Murphy
2022-06-17 11:35 ` Corentin Labbe
2022-06-17 11:43 ` MR
0 siblings, 2 replies; 7+ messages in thread
From: Robin Murphy @ 2022-06-17 9:58 UTC (permalink / raw)
To: Corentin Labbe, heiko, robh+dt, krzysztof.kozlowski+dt,
linux-rockchip, linux-arm-kernel
Cc: linux-kernel
On 2022-06-17 10:06, Corentin Labbe wrote:
> Hello
>
> I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
> It boot normally up to starting init but it stucks shorty after.
> It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
> When disabling CONFIG_USB, the board boots successfully.
>
> In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
> According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
> Can it be possible that the problem was that the power port being disabled ?
Indeed, I believe the OF graph error is just a meaningless annoyance,
but the general problem sounds like it's probably the same thing that's
come up before:
https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should
help confirm that. I have no idea if it's still an open problem, or if
it's been fixed and you might just need to define the proper power role
in the DT; this just triggered a memory of that older thread :)
Robin.
> dmesg of a bad boot:
> [ 0.000000] Linux version 5.19.0-rc2-next-20220614-00140-gf1da72cc3751 (compile@Red) (aarch64-unknown-linux-gnu-gcc (Gentoo 11.3.0 p4) 11.3.0, GNU ld (Gentoo 2.37_p1 p2) 2.37) #194 SMP PREEMPT Fri Jun 17 08:42:30 CEST 2022
> [ 0.000000] Machine model: Firefly ROC-RK3399-PC Board
> [ 0.000000] efi: UEFI not found.
> [ 0.000000] NUMA: No NUMA configuration found
> [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
> [ 0.000000] NUMA: NODE_DATA [mem 0xf77ddb40-0xf77dffff]
> [ 0.000000] Zone ranges:
> [ 0.000000] DMA [mem 0x0000000000200000-0x00000000f7ffffff]
> [ 0.000000] DMA32 empty
> [ 0.000000] Normal empty
> [ 0.000000] Movable zone start for each node
> [ 0.000000] Early memory node ranges
> [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
> [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
> [ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
> [ 0.000000] cma: Reserved 32 MiB at 0x00000000ee000000
> [ 0.000000] psci: probing for conduit method from DT.
> [ 0.000000] psci: PSCIv1.1 detected in firmware.
> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
> [ 0.000000] psci: SMC Calling Convention v1.2
> [ 0.000000] percpu: Embedded 20 pages/cpu s44584 r8192 d29144 u81920
> [ 0.000000] Detected VIPT I-cache on CPU0
> [ 0.000000] CPU features: detected: GIC system register CPU interface
> [ 0.000000] CPU features: detected: ARM erratum 845719
> [ 0.000000] Fallback order for Node 0: 0
> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
> [ 0.000000] Policy zone: DMA
> [ 0.000000] Kernel command line: console=ttyS2,1500000n8 root=/dev/ram0 ip=dhcp ip=dhcp
> [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
> [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [ 0.000000] Memory: 3883504K/4061184K available (16064K kernel code, 3398K rwdata, 9040K rodata, 6976K init, 581K bss, 144912K reserved, 32768K cma-reserved)
> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
> [ 0.000000] rcu: RCU event tracing is enabled.
> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
> [ 0.000000] Trampoline variant of Tasks RCU enabled.
> [ 0.000000] Tracing variant of Tasks RCU enabled.
> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
> [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
> [ 0.000000] GICv3: 256 SPIs implemented
> [ 0.000000] GICv3: 0 Extended SPIs implemented
> [ 0.000000] Root IRQ handler: gic_handle_irq
> [ 0.000000] GICv3: GICv3 features: 16 PPIs
> [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
> [ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
> [ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @480000 (flat, esz 8, psz 64K, shr 0)
> [ 0.000000] ITS: using cache flushing for cmd queue
> [ 0.000000] GICv3: using LPI property table @0x0000000000440000
> [ 0.000000] GIC: using cache flushing for LPI property table
> [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000000450000
> [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
> [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
> [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
> [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
> [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
> [ 0.004263] Console: colour dummy device 80x25
> [ 0.004389] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
> [ 0.004409] pid_max: default: 32768 minimum: 301
> [ 0.004533] LSM: Security Framework initializing
> [ 0.004698] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
> [ 0.004734] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
> [ 0.007236] cblist_init_generic: Setting adjustable number of callback queues.
> [ 0.007256] cblist_init_generic: Setting shift to 3 and lim to 1.
> [ 0.007383] cblist_init_generic: Setting shift to 3 and lim to 1.
> [ 0.007640] rcu: Hierarchical SRCU implementation.
> [ 0.008046] Platform MSI: interrupt-controller@fee20000 domain created
> [ 0.008547] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
> [ 0.008870] fsl-mc MSI: interrupt-controller@fee20000 domain created
> [ 0.015302] EFI services will not be available.
> [ 0.015877] smp: Bringing up secondary CPUs ...
> [ 0.016666] Detected VIPT I-cache on CPU1
> [ 0.016715] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
> [ 0.016737] GICv3: CPU1: using allocated LPI pending table @0x0000000000460000
> [ 0.016799] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
> [ 0.017650] Detected VIPT I-cache on CPU2
> [ 0.017688] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
> [ 0.017706] GICv3: CPU2: using allocated LPI pending table @0x0000000000470000
> [ 0.017744] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
> [ 0.018528] Detected VIPT I-cache on CPU3
> [ 0.018563] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
> [ 0.018581] GICv3: CPU3: using allocated LPI pending table @0x0000000000500000
> [ 0.018617] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
> [ 0.019430] CPU features: detected: Spectre-v2
> [ 0.019441] CPU features: detected: Spectre-v3a
> [ 0.019449] CPU features: detected: Spectre-BHB
> [ 0.019460] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
> [ 0.019465] Detected PIPT I-cache on CPU4
> [ 0.019500] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
> [ 0.019518] GICv3: CPU4: using allocated LPI pending table @0x0000000000510000
> [ 0.019558] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
> [ 0.020382] Detected PIPT I-cache on CPU5
> [ 0.020414] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
> [ 0.020430] GICv3: CPU5: using allocated LPI pending table @0x0000000000520000
> [ 0.020462] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
> [ 0.020577] smp: Brought up 1 node, 6 CPUs
> [ 0.020589] SMP: Total of 6 processors activated.
> [ 0.020596] CPU features: detected: 32-bit EL0 Support
> [ 0.020600] CPU features: detected: 32-bit EL1 Support
> [ 0.020607] CPU features: detected: CRC32 instructions
> [ 0.021930] CPU: All CPU(s) started at EL2
> [ 0.022004] alternatives: patching kernel code
> [ 0.025032] devtmpfs: initialized
> [ 0.035691] KASLR disabled due to lack of seed
> [ 0.035877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
> [ 0.035895] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
> [ 0.036700] pinctrl core: initialized pinctrl subsystem
> [ 0.037742] DMI not present or invalid.
> [ 0.038508] NET: Registered PF_NETLINK/PF_ROUTE protocol family
> [ 0.040015] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
> [ 0.040446] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
> [ 0.040790] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
> [ 0.040849] audit: initializing netlink subsys (disabled)
> [ 0.041054] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
> [ 0.042537] thermal_sys: Registered thermal governor 'step_wise'
> [ 0.042544] thermal_sys: Registered thermal governor 'power_allocator'
> [ 0.042968] cpuidle: using governor menu
> [ 0.043150] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
> [ 0.043333] ASID allocator initialised with 65536 entries
> [ 0.043342] HugeTLB: can optimize 4095 vmemmap pages for hugepages-1048576kB
> [ 0.043349] HugeTLB: can optimize 127 vmemmap pages for hugepages-32768kB
> [ 0.043354] HugeTLB: can optimize 7 vmemmap pages for hugepages-2048kB
> [ 0.043359] HugeTLB: can optimize 0 vmemmap pages for hugepages-64kB
> [ 0.045524] Serial: AMBA PL011 UART driver
> [ 0.076636] platform ff770000.syscon:phy@f780: Fixing up cyclic dependency with fe330000.mmc
> [ 0.084251] platform ff940000.hdmi: Fixing up cyclic dependency with ff8f0000.vop
> [ 0.084309] platform ff940000.hdmi: Fixing up cyclic dependency with ff900000.vop
> [ 0.092195] rockchip-gpio ff720000.gpio: probed /pinctrl/gpio@ff720000
> [ 0.093023] rockchip-gpio ff730000.gpio: probed /pinctrl/gpio@ff730000
> [ 0.093575] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000
> [ 0.094176] rockchip-gpio ff788000.gpio: probed /pinctrl/gpio@ff788000
> [ 0.094721] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000
> [ 0.115188] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
> [ 0.115199] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
> [ 0.115206] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
> [ 0.115212] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
> [ 0.117251] ACPI: Interpreter disabled.
> [ 0.122071] iommu: Default domain type: Translated
> [ 0.122078] iommu: DMA domain TLB invalidation policy: strict mode
> [ 0.122353] SCSI subsystem initialized
> [ 0.122741] usbcore: registered new interface driver usbfs
> [ 0.122785] usbcore: registered new interface driver hub
> [ 0.122819] usbcore: registered new device driver usb
> [ 0.124733] pps_core: LinuxPPS API ver. 1 registered
> [ 0.124738] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
> [ 0.124752] PTP clock support registered
> [ 0.124964] EDAC MC: Ver: 3.0.0
> [ 0.127627] FPGA manager framework
> [ 0.127725] Advanced Linux Sound Architecture Driver Initialized.
> [ 0.128434] vgaarb: loaded
> [ 0.128760] clocksource: Switched to clocksource arch_sys_counter
> [ 0.129141] VFS: Disk quotas dquot_6.6.0
> [ 0.129195] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> [ 0.129399] pnp: PnP ACPI: disabled
> [ 0.138807] NET: Registered PF_INET protocol family
> [ 0.139074] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
> [ 0.143430] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
> [ 0.143539] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
> [ 0.143564] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
> [ 0.143947] TCP bind bhash tables hash table entries: 32768 (order: 7, 786432 bytes, linear)
> [ 0.144919] TCP: Hash tables configured (established 32768 bind 32768)
> [ 0.145036] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
> [ 0.145179] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
> [ 0.145462] NET: Registered PF_UNIX/PF_LOCAL protocol family
> [ 0.145924] RPC: Registered named UNIX socket transport module.
> [ 0.145931] RPC: Registered udp transport module.
> [ 0.145934] RPC: Registered tcp transport module.
> [ 0.145938] RPC: Registered tcp NFSv4.1 backchannel transport module.
> [ 0.145947] PCI: CLS 0 bytes, default 64
> [ 0.146292] Trying to unpack rootfs image as initramfs...
> [ 0.146985] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
> [ 0.147416] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
> [ 0.148134] kvm [1]: IPA Size Limit: 40 bits
> [ 0.150097] kvm [1]: vgic-v2@fff20000
> [ 0.150127] kvm [1]: GIC system register CPU interface enabled
> [ 0.150356] kvm [1]: vgic interrupt IRQ18
> [ 0.150571] kvm [1]: Hyp mode initialized successfully
> [ 0.152166] Initialise system trusted keyrings
> [ 0.152432] workingset: timestamp_bits=42 max_order=20 bucket_order=0
> [ 0.159762] squashfs: version 4.0 (2009/01/31) Phillip Lougher
> [ 0.160556] NFS: Registering the id_resolver key type
> [ 0.160603] Key type id_resolver registered
> [ 0.160607] Key type id_legacy registered
> [ 0.160691] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
> [ 0.160697] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
> [ 0.160959] 9p: Installing v9fs 9p2000 file system support
> [ 0.225217] Key type asymmetric registered
> [ 0.22
> [ 2.398776] Freeing initrd memory: 30120K
> [ 2.442065] tun: Universal TUN/TAP device driver, 1.6
> [ 2.443653] thunder_xcv, ver 1.0
> [ 2.443695] thunder_bgx, ver 1.0
> [ 2.443729] nicpf, ver 1.0
> [ 2.446229] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
> [ 2.446238] hns3: Copyright (c) 2017 Huawei Corporation.
> [ 2.446298] hclge is initializing
> [ 2.446316] e1000: Intel(R) PRO/1000 Network Driver
> [ 2.446320] e1000: Copyright (c) 1999-2006 Intel Corporation.
> [ 2.446359] e1000e: Intel(R) PRO/1000 Network Driver
> [ 2.446362] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
> [ 2.446400] igb: Intel(R) Gigabit Ethernet Network Driver
> [ 2.446404] igb: Copyright (c) 2007-2014 Intel Corporation.
> [ 2.446443] igbvf: Intel(R) Gigabit Virtual Function Network Driver
> [ 2.446447] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
> [ 2.447097] sky2: driver version 1.30
> [ 2.449286] VFIO - User Level meta-driver version: 0.3
> [ 2.457362] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 2.457373] ehci-pci: EHCI PCI platform driver
> [ 2.457409] ehci-platform: EHCI generic platform driver
> [ 2.457678] ehci-orion: EHCI orion driver
> [ 2.457883] ehci-exynos: EHCI Exynos driver
> [ 2.458062] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> [ 2.458087] ohci-pci: OHCI PCI platform driver
> [ 2.458133] ohci-platform: OHCI generic platform driver
> [ 2.458377] ohci-exynos: OHCI Exynos driver
> [ 2.459499] usbcore: registered new interface driver usb-storage
> [ 2.464840] i2c_dev: i2c /dev entries driver
> [ 2.483646] dw_wdt ff848000.watchdog: No valid TOPs array specified
> [ 2.489132] sdhci: Secure Digital Host Controller Interface driver
> [ 2.489141] sdhci: Copyright(c) Pierre Ossman
> [ 2.490655] Synopsys Designware Multimedia Card Interface Driver
> [ 2.492809] sdhci-pltfm: SDHCI platform and OF driver helper
> [ 2.496050] mmc1: CQHCI version 5.10
> [ 2.498229] ledtrig-cpu: registered to indicate activity on CPUs
> [ 2.500422] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
> [ 2.501687] usbcore: registered new interface driver usbhid
> [ 2.501694] usbhid: USB HID core driver
> [ 2.513858] NET: Registered PF_PACKET protocol family
> [ 2.514032] 9pnet: Installing 9P2000 support
> [ 2.514102] Key type dns_resolver registered
> [ 2.514738] registered taskstats version 1
> [ 2.514757] Loading compiled-in X.509 certificates
> [ 2.520908] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
> [ 2.567578] rockchip-usb2phy ff770000.syscon:usb2phy@e450: failed to create phy
> [ 2.572233] rockchip-usb2phy ff770000.syscon:usb2phy@e460: failed to create phy
> [ 2.596788] rk808 0-001b: chip id: 0x0
> [ 2.603697] rk808-regulator rk808-regulator: there is no dvs0 gpio
> [ 2.603742] rk808-regulator rk808-regulator: there is no dvs1 gpio
> [ 2.624666] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
> [ 2.629750] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
> [ 2.636958] cpu cpu0: EM: created perf domain
> [ 2.638707] cpu cpu4: EM: created perf domain
> [ 2.662475] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> [ 2.662502] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
> [ 2.662622] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
> [ 2.662646] xhci-hcd xhci-hcd.0.auto: irq 67, io mem 0xfe800000
> [ 2.662788] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
> [ 2.662796] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
> [ 2.662805] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
> [ 2.663832] hub 1-0:1.0: USB hub found
> [ 2.663862] hub 1-0:1.0: 1 port detected
> [ 2.664123] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
> [ 2.664619] hub 2-0:1.0: USB hub found
> [ 2.664640] hub 2-0:1.0: 1 port detected
> [ 2.674843] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> [ 2.674869] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
> [ 2.674997] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
> [ 2.675051] xhci-hcd xhci-hcd.1.auto: irq 68, io mem 0xfe900000
> [ 2.675201] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
> [ 2.675211] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
> [ 2.675221] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
> [ 2.675766] hub 3-0:1.0: USB hub found
> [ 2.675791] hub 3-0:1.0: 1 port detected
> [ 2.676072] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
> [ 2.676442] hub 4-0:1.0: USB hub found
> [ 2.676462] hub 4-0:1.0: 1 port detected
> [ 2.682696] ehci-platform fe380000.usb: EHCI Host Controller
> [ 2.682721] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
> [ 2.682835] ehci-platform fe380000.usb: irq 69, io mem 0xfe380000
> [ 2.684546] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
> [ 2.684568] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
> [ 2.684689] ohci-platform fe3a0000.usb: irq 71, io mem 0xfe3a0000
> [ 2.684773] ehci-platform fe3c0000.usb: EHCI Host Controller
> [ 2.684788] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 7
> [ 2.684863] ehci-platform fe3c0000.usb: irq 70, io mem 0xfe3c0000
> [ 2.686659] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
> [ 2.686682] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 8
> [ 2.686813] ohci-platform fe3e0000.usb: irq 72, io mem 0xfe3e0000
> [ 2.688941] input: gpio-keys as /devices/platform/gpio-keys/input/input0
> [ 2.689400] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
> [ 2.689434] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
> [ 2.689442] dwmmc_rockchip fe320000.mmc: Version ID is 270a
> [ 2.689483] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 74,32 bit host data width,256 deep fifo
> [ 2.689827] dwmmc_rockchip fe320000.mmc: Got CD GPIO
> [ 2.700909] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
> [ 2.701762] hub 5-0:1.0: USB hub found
> [ 2.701796] hub 5-0:1.0: 1 port detected
> [ 2.703670] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
> [ 2.716867] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
> [ 2.717615] hub 7-0:1.0: USB hub found
> [ 2.717649] hub 7-0:1.0: 1 port detected
> [ 2.749885] hub 8-0:1.0: USB hub found
> [ 2.749935] hub 8-0:1.0: 1 port detected
> [ 2.751419] hub 6-0:1.0: USB hub found
> [ 2.751471] hub 6-0:1.0: 1 port detected
> [ 2.772382] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
> [ 2.973076] usb 7-1: new high-speed USB device number 2 using ehci-platform
> [ 3.005758] dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 136
> [ 3.005789] mmc0: new ultra high speed SDR50 SDHC card at address 0007
> [ 3.006862] mmcblk0: mmc0:0007 SD4GB 3.71 GiB
> [ 3.009227] mmcblk0: p1 p2
> [ 3.132986] hub 7-1:1.0: USB hub found
> [ 3.133339] hub 7-1:1.0: 4 ports detected
> [ 15.042378] ALSA device list:
> [ 15.042404] No soundcards found.
> [ 15.042770] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
> [ 15.047594] Freeing unused kernel memory: 6976K
> [ 15.047708] Run /init as init process
> Starting syslogd: OK
> Starting klogd: OK
> Running sysctl: OK
> Populating /dev using udev: [ 15.173509] udevd[180]: starting version 3.2.10
> [ 33.092753] random: crng init done
> [ 33.097189] udevd[181]: starting eudev-3.2.10
> [ 33.270362] pwm-backlight backlight: supply power not found, using dummy regulator
> [ 33.277620] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
> [ 33.277630] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
> [ 33.277718] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
> [ 33.281235] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
> [ 33.281246] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
> [ 33.281250] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
> [ 33.281259] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
> [ 33.281290] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
> [ 33.281293] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
> [ 33.284736] rockchip-vop ff8f0000.vop: Adding to iommu group 2
> [ 33.285547] rockchip-vop ff900000.vop: Adding to iommu group 3
> [ 33.286307] rk_gmac-dwmac fe300000.ethernet: init for RGMII
> [ 33.286461] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
> [ 33.286467] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
> [ 33.286470] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
> [ 33.286473] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
> [ 33.286475] rk_gmac-dwmac fe300000.ethernet: COE Type 2
> [ 33.286478] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
> [ 33.286480] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
> [ 33.286530] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
> [ 33.286533] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
> [ 33.286535] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
> [ 33.287020] input: adc-keys as /devices/platform/adc-keys/input/input1
> [ 33.287462] OF: graph: no port node found in /i2c@ff160000/usb-typec@22
> [ 33.301175] mc: Linux media interface: v0.10
> [ 33.304453] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops [rockchipdrm])
> [ 33.304557] [drm] unsupported AFBC format[3231564e]
> [ 33.306210] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops [rockchipdrm])
> [ 33.306357] dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
> [ 33.306830] videodev: Linux video capture interface: v2.00
> [ 33.308965] dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
> [ 33.309136] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
> [ 33.312522] OF: graph: no port node found in /i2c@ff3d0000/usb-typec@22
> [ 33.315768] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm])
> [ 33.317635] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
> [ 33.317788] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
> [ 33.317853] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
> [ 33.317905] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
> [ 33.320726] hantro-vpu ff650000.video-codec: Adding to iommu group 0
> [ 33.321444] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video0
> [ 33.321556] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video1
> [ 33.326240] rk808-rtc rk808-rtc: registered as rtc0
> [ 33.326745] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:51:21 UTC (1358499081)
>
> Regards
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 9:58 ` Robin Murphy
@ 2022-06-17 11:35 ` Corentin Labbe
2022-06-17 11:48 ` MR
2022-06-17 11:43 ` MR
1 sibling, 1 reply; 7+ messages in thread
From: Corentin Labbe @ 2022-06-17 11:35 UTC (permalink / raw)
To: Robin Murphy
Cc: heiko, robh+dt, krzysztof.kozlowski+dt, linux-rockchip,
linux-arm-kernel, linux-kernel
Le Fri, Jun 17, 2022 at 10:58:03AM +0100, Robin Murphy a écrit :
> On 2022-06-17 10:06, Corentin Labbe wrote:
> > Hello
> >
> > I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
> > It boot normally up to starting init but it stucks shorty after.
> > It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
> > When disabling CONFIG_USB, the board boots successfully.
> >
> > In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
> > According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
> > Can it be possible that the problem was that the power port being disabled ?
>
> Indeed, I believe the OF graph error is just a meaningless annoyance,
> but the general problem sounds like it's probably the same thing that's
> come up before:
>
> https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
>
> Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should
> help confirm that. I have no idea if it's still an open problem, or if
> it's been fixed and you might just need to define the proper power role
> in the DT; this just triggered a memory of that older thread :)
>
If I comment fusb0 node in arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi, the board boot well.
With the following patch, the boards boot well also:
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
index 0e45cc2d195b..60c400ca4034 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
@@ -552,6 +552,22 @@ fusb0: usb-typec@22 {
pinctrl-0 = <&fusb0_int>;
vbus-supply = <&vcc_vbus_typec0>;
status = "okay";
+
+ connector {
+ compatible = "usb-c-connector";
+ data-role = "host";
+ label = "USB-C";
+ power-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ };
+ };
+ };
};
mp8859: regulator@66 {
I think this patch is the proper way to fix, I will send it soon.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 9:58 ` Robin Murphy
2022-06-17 11:35 ` Corentin Labbe
@ 2022-06-17 11:43 ` MR
2022-06-17 11:47 ` Corentin Labbe
1 sibling, 1 reply; 7+ messages in thread
From: MR @ 2022-06-17 11:43 UTC (permalink / raw)
To: linux-rockchip, Robin Murphy, Corentin Labbe, heiko, robh+dt,
krzysztof.kozlowski+dt, linux-arm-kernel
Cc: linux-kernel
Am 17. Juni 2022 11:58:03 MESZ schrieb Robin Murphy <robin.murphy@arm.com>:
>On 2022-06-17 10:06, Corentin Labbe wrote:
>> Hello
>>
>> I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
>> It boot normally up to starting init but it stucks shorty after.
>> It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
>> When disabling CONFIG_USB, the board boots successfully.
>>
>> In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
>> According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
>> Can it be possible that the problem was that the power port being disabled ?
>
>Indeed, I believe the OF graph error is just a meaningless annoyance, but the general problem sounds like it's probably the same thing that's come up before:
>
>https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
>
>Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should help confirm that. I have no idea if it's still an open problem, or if it's been fixed and you might just need to define the proper power role in the DT; this just triggered a memory of that older thread :)
>
>Robin.
Yes, the issue above is still there. I therefore use dumb 5 V, 4 A USB power supplies that do not react on the USB-C communication.
Markus
>
>> dmesg of a bad boot:
>> [ 0.000000] Linux version 5.19.0-rc2-next-20220614-00140-gf1da72cc3751 (compile@Red) (aarch64-unknown-linux-gnu-gcc (Gentoo 11.3.0 p4) 11.3.0, GNU ld (Gentoo 2.37_p1 p2) 2.37) #194 SMP PREEMPT Fri Jun 17 08:42:30 CEST 2022
>> [ 0.000000] Machine model: Firefly ROC-RK3399-PC Board
>> [ 0.000000] efi: UEFI not found.
>> [ 0.000000] NUMA: No NUMA configuration found
>> [ 0.000000] NUMA: Faking a node at [mem 0x0000000000200000-0x00000000f7ffffff]
>> [ 0.000000] NUMA: NODE_DATA [mem 0xf77ddb40-0xf77dffff]
>> [ 0.000000] Zone ranges:
>> [ 0.000000] DMA [mem 0x0000000000200000-0x00000000f7ffffff]
>> [ 0.000000] DMA32 empty
>> [ 0.000000] Normal empty
>> [ 0.000000] Movable zone start for each node
>> [ 0.000000] Early memory node ranges
>> [ 0.000000] node 0: [mem 0x0000000000200000-0x00000000f7ffffff]
>> [ 0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000000f7ffffff]
>> [ 0.000000] On node 0, zone DMA: 512 pages in unavailable ranges
>> [ 0.000000] cma: Reserved 32 MiB at 0x00000000ee000000
>> [ 0.000000] psci: probing for conduit method from DT.
>> [ 0.000000] psci: PSCIv1.1 detected in firmware.
>> [ 0.000000] psci: Using standard PSCI v0.2 function IDs
>> [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
>> [ 0.000000] psci: SMC Calling Convention v1.2
>> [ 0.000000] percpu: Embedded 20 pages/cpu s44584 r8192 d29144 u81920
>> [ 0.000000] Detected VIPT I-cache on CPU0
>> [ 0.000000] CPU features: detected: GIC system register CPU interface
>> [ 0.000000] CPU features: detected: ARM erratum 845719
>> [ 0.000000] Fallback order for Node 0: 0
>> [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 999432
>> [ 0.000000] Policy zone: DMA
>> [ 0.000000] Kernel command line: console=ttyS2,1500000n8 root=/dev/ram0 ip=dhcp ip=dhcp
>> [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
>> [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
>> [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
>> [ 0.000000] Memory: 3883504K/4061184K available (16064K kernel code, 3398K rwdata, 9040K rodata, 6976K init, 581K bss, 144912K reserved, 32768K cma-reserved)
>> [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
>> [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
>> [ 0.000000] rcu: RCU event tracing is enabled.
>> [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=6.
>> [ 0.000000] Trampoline variant of Tasks RCU enabled.
>> [ 0.000000] Tracing variant of Tasks RCU enabled.
>> [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
>> [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
>> [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
>> [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
>> [ 0.000000] GICv3: 256 SPIs implemented
>> [ 0.000000] GICv3: 0 Extended SPIs implemented
>> [ 0.000000] Root IRQ handler: gic_handle_irq
>> [ 0.000000] GICv3: GICv3 features: 16 PPIs
>> [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
>> [ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
>> [ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @480000 (flat, esz 8, psz 64K, shr 0)
>> [ 0.000000] ITS: using cache flushing for cmd queue
>> [ 0.000000] GICv3: using LPI property table @0x0000000000440000
>> [ 0.000000] GIC: using cache flushing for LPI property table
>> [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000000450000
>> [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
>> [ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
>> [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
>> [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
>> [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
>> [ 0.000001] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
>> [ 0.004263] Console: colour dummy device 80x25
>> [ 0.004389] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
>> [ 0.004409] pid_max: default: 32768 minimum: 301
>> [ 0.004533] LSM: Security Framework initializing
>> [ 0.004698] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
>> [ 0.004734] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
>> [ 0.007236] cblist_init_generic: Setting adjustable number of callback queues.
>> [ 0.007256] cblist_init_generic: Setting shift to 3 and lim to 1.
>> [ 0.007383] cblist_init_generic: Setting shift to 3 and lim to 1.
>> [ 0.007640] rcu: Hierarchical SRCU implementation.
>> [ 0.008046] Platform MSI: interrupt-controller@fee20000 domain created
>> [ 0.008547] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
>> [ 0.008870] fsl-mc MSI: interrupt-controller@fee20000 domain created
>> [ 0.015302] EFI services will not be available.
>> [ 0.015877] smp: Bringing up secondary CPUs ...
>> [ 0.016666] Detected VIPT I-cache on CPU1
>> [ 0.016715] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
>> [ 0.016737] GICv3: CPU1: using allocated LPI pending table @0x0000000000460000
>> [ 0.016799] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
>> [ 0.017650] Detected VIPT I-cache on CPU2
>> [ 0.017688] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
>> [ 0.017706] GICv3: CPU2: using allocated LPI pending table @0x0000000000470000
>> [ 0.017744] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
>> [ 0.018528] Detected VIPT I-cache on CPU3
>> [ 0.018563] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
>> [ 0.018581] GICv3: CPU3: using allocated LPI pending table @0x0000000000500000
>> [ 0.018617] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
>> [ 0.019430] CPU features: detected: Spectre-v2
>> [ 0.019441] CPU features: detected: Spectre-v3a
>> [ 0.019449] CPU features: detected: Spectre-BHB
>> [ 0.019460] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
>> [ 0.019465] Detected PIPT I-cache on CPU4
>> [ 0.019500] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
>> [ 0.019518] GICv3: CPU4: using allocated LPI pending table @0x0000000000510000
>> [ 0.019558] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
>> [ 0.020382] Detected PIPT I-cache on CPU5
>> [ 0.020414] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
>> [ 0.020430] GICv3: CPU5: using allocated LPI pending table @0x0000000000520000
>> [ 0.020462] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
>> [ 0.020577] smp: Brought up 1 node, 6 CPUs
>> [ 0.020589] SMP: Total of 6 processors activated.
>> [ 0.020596] CPU features: detected: 32-bit EL0 Support
>> [ 0.020600] CPU features: detected: 32-bit EL1 Support
>> [ 0.020607] CPU features: detected: CRC32 instructions
>> [ 0.021930] CPU: All CPU(s) started at EL2
>> [ 0.022004] alternatives: patching kernel code
>> [ 0.025032] devtmpfs: initialized
>> [ 0.035691] KASLR disabled due to lack of seed
>> [ 0.035877] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
>> [ 0.035895] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
>> [ 0.036700] pinctrl core: initialized pinctrl subsystem
>> [ 0.037742] DMI not present or invalid.
>> [ 0.038508] NET: Registered PF_NETLINK/PF_ROUTE protocol family
>> [ 0.040015] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
>> [ 0.040446] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
>> [ 0.040790] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
>> [ 0.040849] audit: initializing netlink subsys (disabled)
>> [ 0.041054] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
>> [ 0.042537] thermal_sys: Registered thermal governor 'step_wise'
>> [ 0.042544] thermal_sys: Registered thermal governor 'power_allocator'
>> [ 0.042968] cpuidle: using governor menu
>> [ 0.043150] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
>> [ 0.043333] ASID allocator initialised with 65536 entries
>> [ 0.043342] HugeTLB: can optimize 4095 vmemmap pages for hugepages-1048576kB
>> [ 0.043349] HugeTLB: can optimize 127 vmemmap pages for hugepages-32768kB
>> [ 0.043354] HugeTLB: can optimize 7 vmemmap pages for hugepages-2048kB
>> [ 0.043359] HugeTLB: can optimize 0 vmemmap pages for hugepages-64kB
>> [ 0.045524] Serial: AMBA PL011 UART driver
>> [ 0.076636] platform ff770000.syscon:phy@f780: Fixing up cyclic dependency with fe330000.mmc
>> [ 0.084251] platform ff940000.hdmi: Fixing up cyclic dependency with ff8f0000.vop
>> [ 0.084309] platform ff940000.hdmi: Fixing up cyclic dependency with ff900000.vop
>> [ 0.092195] rockchip-gpio ff720000.gpio: probed /pinctrl/gpio@ff720000
>> [ 0.093023] rockchip-gpio ff730000.gpio: probed /pinctrl/gpio@ff730000
>> [ 0.093575] rockchip-gpio ff780000.gpio: probed /pinctrl/gpio@ff780000
>> [ 0.094176] rockchip-gpio ff788000.gpio: probed /pinctrl/gpio@ff788000
>> [ 0.094721] rockchip-gpio ff790000.gpio: probed /pinctrl/gpio@ff790000
>> [ 0.115188] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
>> [ 0.115199] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
>> [ 0.115206] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
>> [ 0.115212] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
>> [ 0.117251] ACPI: Interpreter disabled.
>> [ 0.122071] iommu: Default domain type: Translated
>> [ 0.122078] iommu: DMA domain TLB invalidation policy: strict mode
>> [ 0.122353] SCSI subsystem initialized
>> [ 0.122741] usbcore: registered new interface driver usbfs
>> [ 0.122785] usbcore: registered new interface driver hub
>> [ 0.122819] usbcore: registered new device driver usb
>> [ 0.124733] pps_core: LinuxPPS API ver. 1 registered
>> [ 0.124738] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
>> [ 0.124752] PTP clock support registered
>> [ 0.124964] EDAC MC: Ver: 3.0.0
>> [ 0.127627] FPGA manager framework
>> [ 0.127725] Advanced Linux Sound Architecture Driver Initialized.
>> [ 0.128434] vgaarb: loaded
>> [ 0.128760] clocksource: Switched to clocksource arch_sys_counter
>> [ 0.129141] VFS: Disk quotas dquot_6.6.0
>> [ 0.129195] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
>> [ 0.129399] pnp: PnP ACPI: disabled
>> [ 0.138807] NET: Registered PF_INET protocol family
>> [ 0.139074] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
>> [ 0.143430] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
>> [ 0.143539] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
>> [ 0.143564] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
>> [ 0.143947] TCP bind bhash tables hash table entries: 32768 (order: 7, 786432 bytes, linear)
>> [ 0.144919] TCP: Hash tables configured (established 32768 bind 32768)
>> [ 0.145036] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
>> [ 0.145179] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
>> [ 0.145462] NET: Registered PF_UNIX/PF_LOCAL protocol family
>> [ 0.145924] RPC: Registered named UNIX socket transport module.
>> [ 0.145931] RPC: Registered udp transport module.
>> [ 0.145934] RPC: Registered tcp transport module.
>> [ 0.145938] RPC: Registered tcp NFSv4.1 backchannel transport module.
>> [ 0.145947] PCI: CLS 0 bytes, default 64
>> [ 0.146292] Trying to unpack rootfs image as initramfs...
>> [ 0.146985] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
>> [ 0.147416] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
>> [ 0.148134] kvm [1]: IPA Size Limit: 40 bits
>> [ 0.150097] kvm [1]: vgic-v2@fff20000
>> [ 0.150127] kvm [1]: GIC system register CPU interface enabled
>> [ 0.150356] kvm [1]: vgic interrupt IRQ18
>> [ 0.150571] kvm [1]: Hyp mode initialized successfully
>> [ 0.152166] Initialise system trusted keyrings
>> [ 0.152432] workingset: timestamp_bits=42 max_order=20 bucket_order=0
>> [ 0.159762] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>> [ 0.160556] NFS: Registering the id_resolver key type
>> [ 0.160603] Key type id_resolver registered
>> [ 0.160607] Key type id_legacy registered
>> [ 0.160691] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
>> [ 0.160697] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
>> [ 0.160959] 9p: Installing v9fs 9p2000 file system support
>> [ 0.225217] Key type asymmetric registered
>> [ 0.22
>> [ 2.398776] Freeing initrd memory: 30120K
>> [ 2.442065] tun: Universal TUN/TAP device driver, 1.6
>> [ 2.443653] thunder_xcv, ver 1.0
>> [ 2.443695] thunder_bgx, ver 1.0
>> [ 2.443729] nicpf, ver 1.0
>> [ 2.446229] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
>> [ 2.446238] hns3: Copyright (c) 2017 Huawei Corporation.
>> [ 2.446298] hclge is initializing
>> [ 2.446316] e1000: Intel(R) PRO/1000 Network Driver
>> [ 2.446320] e1000: Copyright (c) 1999-2006 Intel Corporation.
>> [ 2.446359] e1000e: Intel(R) PRO/1000 Network Driver
>> [ 2.446362] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
>> [ 2.446400] igb: Intel(R) Gigabit Ethernet Network Driver
>> [ 2.446404] igb: Copyright (c) 2007-2014 Intel Corporation.
>> [ 2.446443] igbvf: Intel(R) Gigabit Virtual Function Network Driver
>> [ 2.446447] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
>> [ 2.447097] sky2: driver version 1.30
>> [ 2.449286] VFIO - User Level meta-driver version: 0.3
>> [ 2.457362] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> [ 2.457373] ehci-pci: EHCI PCI platform driver
>> [ 2.457409] ehci-platform: EHCI generic platform driver
>> [ 2.457678] ehci-orion: EHCI orion driver
>> [ 2.457883] ehci-exynos: EHCI Exynos driver
>> [ 2.458062] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>> [ 2.458087] ohci-pci: OHCI PCI platform driver
>> [ 2.458133] ohci-platform: OHCI generic platform driver
>> [ 2.458377] ohci-exynos: OHCI Exynos driver
>> [ 2.459499] usbcore: registered new interface driver usb-storage
>> [ 2.464840] i2c_dev: i2c /dev entries driver
>> [ 2.483646] dw_wdt ff848000.watchdog: No valid TOPs array specified
>> [ 2.489132] sdhci: Secure Digital Host Controller Interface driver
>> [ 2.489141] sdhci: Copyright(c) Pierre Ossman
>> [ 2.490655] Synopsys Designware Multimedia Card Interface Driver
>> [ 2.492809] sdhci-pltfm: SDHCI platform and OF driver helper
>> [ 2.496050] mmc1: CQHCI version 5.10
>> [ 2.498229] ledtrig-cpu: registered to indicate activity on CPUs
>> [ 2.500422] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
>> [ 2.501687] usbcore: registered new interface driver usbhid
>> [ 2.501694] usbhid: USB HID core driver
>> [ 2.513858] NET: Registered PF_PACKET protocol family
>> [ 2.514032] 9pnet: Installing 9P2000 support
>> [ 2.514102] Key type dns_resolver registered
>> [ 2.514738] registered taskstats version 1
>> [ 2.514757] Loading compiled-in X.509 certificates
>> [ 2.520908] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
>> [ 2.567578] rockchip-usb2phy ff770000.syscon:usb2phy@e450: failed to create phy
>> [ 2.572233] rockchip-usb2phy ff770000.syscon:usb2phy@e460: failed to create phy
>> [ 2.596788] rk808 0-001b: chip id: 0x0
>> [ 2.603697] rk808-regulator rk808-regulator: there is no dvs0 gpio
>> [ 2.603742] rk808-regulator rk808-regulator: there is no dvs1 gpio
>> [ 2.624666] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
>> [ 2.629750] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
>> [ 2.636958] cpu cpu0: EM: created perf domain
>> [ 2.638707] cpu cpu4: EM: created perf domain
>> [ 2.662475] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>> [ 2.662502] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
>> [ 2.662622] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
>> [ 2.662646] xhci-hcd xhci-hcd.0.auto: irq 67, io mem 0xfe800000
>> [ 2.662788] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
>> [ 2.662796] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
>> [ 2.662805] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
>> [ 2.663832] hub 1-0:1.0: USB hub found
>> [ 2.663862] hub 1-0:1.0: 1 port detected
>> [ 2.664123] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
>> [ 2.664619] hub 2-0:1.0: USB hub found
>> [ 2.664640] hub 2-0:1.0: 1 port detected
>> [ 2.674843] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>> [ 2.674869] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
>> [ 2.674997] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
>> [ 2.675051] xhci-hcd xhci-hcd.1.auto: irq 68, io mem 0xfe900000
>> [ 2.675201] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
>> [ 2.675211] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
>> [ 2.675221] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
>> [ 2.675766] hub 3-0:1.0: USB hub found
>> [ 2.675791] hub 3-0:1.0: 1 port detected
>> [ 2.676072] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
>> [ 2.676442] hub 4-0:1.0: USB hub found
>> [ 2.676462] hub 4-0:1.0: 1 port detected
>> [ 2.682696] ehci-platform fe380000.usb: EHCI Host Controller
>> [ 2.682721] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
>> [ 2.682835] ehci-platform fe380000.usb: irq 69, io mem 0xfe380000
>> [ 2.684546] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
>> [ 2.684568] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
>> [ 2.684689] ohci-platform fe3a0000.usb: irq 71, io mem 0xfe3a0000
>> [ 2.684773] ehci-platform fe3c0000.usb: EHCI Host Controller
>> [ 2.684788] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 7
>> [ 2.684863] ehci-platform fe3c0000.usb: irq 70, io mem 0xfe3c0000
>> [ 2.686659] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
>> [ 2.686682] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 8
>> [ 2.686813] ohci-platform fe3e0000.usb: irq 72, io mem 0xfe3e0000
>> [ 2.688941] input: gpio-keys as /devices/platform/gpio-keys/input/input0
>> [ 2.689400] dwmmc_rockchip fe320000.mmc: IDMAC supports 32-bit address mode.
>> [ 2.689434] dwmmc_rockchip fe320000.mmc: Using internal DMA controller.
>> [ 2.689442] dwmmc_rockchip fe320000.mmc: Version ID is 270a
>> [ 2.689483] dwmmc_rockchip fe320000.mmc: DW MMC controller at irq 74,32 bit host data width,256 deep fifo
>> [ 2.689827] dwmmc_rockchip fe320000.mmc: Got CD GPIO
>> [ 2.700909] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
>> [ 2.701762] hub 5-0:1.0: USB hub found
>> [ 2.701796] hub 5-0:1.0: 1 port detected
>> [ 2.703670] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
>> [ 2.716867] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
>> [ 2.717615] hub 7-0:1.0: USB hub found
>> [ 2.717649] hub 7-0:1.0: 1 port detected
>> [ 2.749885] hub 8-0:1.0: USB hub found
>> [ 2.749935] hub 8-0:1.0: 1 port detected
>> [ 2.751419] hub 6-0:1.0: USB hub found
>> [ 2.751471] hub 6-0:1.0: 1 port detected
>> [ 2.772382] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0)
>> [ 2.973076] usb 7-1: new high-speed USB device number 2 using ehci-platform
>> [ 3.005758] dwmmc_rockchip fe320000.mmc: Successfully tuned phase to 136
>> [ 3.005789] mmc0: new ultra high speed SDR50 SDHC card at address 0007
>> [ 3.006862] mmcblk0: mmc0:0007 SD4GB 3.71 GiB
>> [ 3.009227] mmcblk0: p1 p2
>> [ 3.132986] hub 7-1:1.0: USB hub found
>> [ 3.133339] hub 7-1:1.0: 4 ports detected
>> [ 15.042378] ALSA device list:
>> [ 15.042404] No soundcards found.
>> [ 15.042770] dw-apb-uart ff1a0000.serial: forbid DMA for kernel console
>> [ 15.047594] Freeing unused kernel memory: 6976K
>> [ 15.047708] Run /init as init process
>> Starting syslogd: OK
>> Starting klogd: OK
>> Running sysctl: OK
>> Populating /dev using udev: [ 15.173509] udevd[180]: starting version 3.2.10
>> [ 33.092753] random: crng init done
>> [ 33.097189] udevd[181]: starting eudev-3.2.10
>> [ 33.270362] pwm-backlight backlight: supply power not found, using dummy regulator
>> [ 33.277620] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
>> [ 33.277630] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
>> [ 33.277718] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
>> [ 33.281235] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
>> [ 33.281246] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
>> [ 33.281250] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
>> [ 33.281259] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
>> [ 33.281290] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
>> [ 33.281293] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
>> [ 33.284736] rockchip-vop ff8f0000.vop: Adding to iommu group 2
>> [ 33.285547] rockchip-vop ff900000.vop: Adding to iommu group 3
>> [ 33.286307] rk_gmac-dwmac fe300000.ethernet: init for RGMII
>> [ 33.286461] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
>> [ 33.286467] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
>> [ 33.286470] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
>> [ 33.286473] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
>> [ 33.286475] rk_gmac-dwmac fe300000.ethernet: COE Type 2
>> [ 33.286478] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
>> [ 33.286480] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
>> [ 33.286530] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
>> [ 33.286533] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
>> [ 33.286535] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
>> [ 33.287020] input: adc-keys as /devices/platform/adc-keys/input/input1
>> [ 33.287462] OF: graph: no port node found in /i2c@ff160000/usb-typec@22
>> [ 33.301175] mc: Linux media interface: v0.10
>> [ 33.304453] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops [rockchipdrm])
>> [ 33.304557] [drm] unsupported AFBC format[3231564e]
>> [ 33.306210] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops [rockchipdrm])
>> [ 33.306357] dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
>> [ 33.306830] videodev: Linux video capture interface: v2.00
>> [ 33.308965] dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
>> [ 33.309136] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
>> [ 33.312522] OF: graph: no port node found in /i2c@ff3d0000/usb-typec@22
>> [ 33.315768] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm])
>> [ 33.317635] hantro_vpu: module is from the staging directory, the quality is unknown, you have been warned.
>> [ 33.317788] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
>> [ 33.317853] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
>> [ 33.317905] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
>> [ 33.320726] hantro-vpu ff650000.video-codec: Adding to iommu group 0
>> [ 33.321444] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-enc as /dev/video0
>> [ 33.321556] hantro-vpu ff650000.video-codec: registered rockchip,rk3399-vpu-dec as /dev/video1
>> [ 33.326240] rk808-rtc rk808-rtc: registered as rtc0
>> [ 33.326745] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:51:21 UTC (1358499081)
>>
>> Regards
>>
>> _______________________________________________
>> Linux-rockchip mailing list
>> Linux-rockchip@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
>_______________________________________________
>Linux-rockchip mailing list
>Linux-rockchip@lists.infradead.org
>http://lists.infradead.org/mailman/listinfo/linux-rockchip
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 11:43 ` MR
@ 2022-06-17 11:47 ` Corentin Labbe
2022-06-17 11:50 ` MR
0 siblings, 1 reply; 7+ messages in thread
From: Corentin Labbe @ 2022-06-17 11:47 UTC (permalink / raw)
To: MR
Cc: linux-rockchip, Robin Murphy, heiko, robh+dt,
krzysztof.kozlowski+dt, linux-arm-kernel, linux-kernel
Le Fri, Jun 17, 2022 at 01:43:05PM +0200, MR a écrit :
>
>
> Am 17. Juni 2022 11:58:03 MESZ schrieb Robin Murphy <robin.murphy@arm.com>:
> >On 2022-06-17 10:06, Corentin Labbe wrote:
> >> Hello
> >>
> >> I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
> >> It boot normally up to starting init but it stucks shorty after.
> >> It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
> >> When disabling CONFIG_USB, the board boots successfully.
> >>
> >> In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
> >> According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
> >> Can it be possible that the problem was that the power port being disabled ?
> >
> >Indeed, I believe the OF graph error is just a meaningless annoyance, but the general problem sounds like it's probably the same thing that's come up before:
> >
> >https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
> >
> >Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should help confirm that. I have no idea if it's still an open problem, or if it's been fixed and you might just need to define the proper power role in the DT; this just triggered a memory of that older thread :)
> >
> >Robin.
>
> Yes, the issue above is still there. I therefore use dumb 5 V, 4 A USB power supplies that do not react on the USB-C communication.
>
> Markus
@Markus
Could you try the diff I just send ?
Thanks
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 11:35 ` Corentin Labbe
@ 2022-06-17 11:48 ` MR
0 siblings, 0 replies; 7+ messages in thread
From: MR @ 2022-06-17 11:48 UTC (permalink / raw)
To: linux-rockchip, Corentin Labbe, Robin Murphy
Cc: heiko, robh+dt, krzysztof.kozlowski+dt, linux-arm-kernel,
linux-kernel
Am 17. Juni 2022 13:35:20 MESZ schrieb Corentin Labbe <clabbe.montjoie@gmail.com>:
>Le Fri, Jun 17, 2022 at 10:58:03AM +0100, Robin Murphy a écrit :
>> On 2022-06-17 10:06, Corentin Labbe wrote:
>> > Hello
>> >
>> > I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
>> > It boot normally up to starting init but it stucks shorty after.
>> > It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
>> > When disabling CONFIG_USB, the board boots successfully.
>> >
>> > In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
>> > According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
>> > Can it be possible that the problem was that the power port being disabled ?
>>
>> Indeed, I believe the OF graph error is just a meaningless annoyance,
>> but the general problem sounds like it's probably the same thing that's
>> come up before:
>>
>> https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
>>
>> Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should
>> help confirm that. I have no idea if it's still an open problem, or if
>> it's been fixed and you might just need to define the proper power role
>> in the DT; this just triggered a memory of that older thread :)
>>
>
>If I comment fusb0 node in arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi, the board boot well.
>
>With the following patch, the boards boot well also:
>diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>index 0e45cc2d195b..60c400ca4034 100644
>--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
>@@ -552,6 +552,22 @@ fusb0: usb-typec@22 {
> pinctrl-0 = <&fusb0_int>;
> vbus-supply = <&vcc_vbus_typec0>;
> status = "okay";
>+
>+ connector {
>+ compatible = "usb-c-connector";
>+ data-role = "host";
>+ label = "USB-C";
>+ power-role = "dual";
>+
>+ ports {
>+ #address-cells = <1>;
>+ #size-cells = <0>;
>+
>+ port@0 {
>+ reg = <0>;
>+ };
>+ };
>+ };
> };
>
> mp8859: regulator@66 {
>
>I think this patch is the proper way to fix, I will send it soon.
>
Thanks, happy to see that this works now.
>Linux-rockchip mailing list
>Linux-rockchip@lists.infradead.org
>http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: rk3399-roc-pc does not boot
2022-06-17 11:47 ` Corentin Labbe
@ 2022-06-17 11:50 ` MR
0 siblings, 0 replies; 7+ messages in thread
From: MR @ 2022-06-17 11:50 UTC (permalink / raw)
To: linux-rockchip, Corentin Labbe
Cc: Robin Murphy, heiko, robh+dt, krzysztof.kozlowski+dt,
linux-arm-kernel, linux-kernel
Am 17. Juni 2022 13:47:05 MESZ schrieb Corentin Labbe <clabbe.montjoie@gmail.com>:
>Le Fri, Jun 17, 2022 at 01:43:05PM +0200, MR a écrit :
>>
>>
>> Am 17. Juni 2022 11:58:03 MESZ schrieb Robin Murphy <robin.murphy@arm.com>:
>> >On 2022-06-17 10:06, Corentin Labbe wrote:
>> >> Hello
>> >>
>> >> I try to add rk3399-roc-pc to kernelCI but this board fail to ends its boot with any kernel I try.
>> >> It boot normally up to starting init but it stucks shorty after.
>> >> It fail on 5.10, 5.15, 5.17, 5.18 and linux-next.
>> >> When disabling CONFIG_USB, the board boots successfully.
>> >>
>> >> In dmesg I see OF: graph: no port node found in /i2c@ff160000/usb-typec@22
>> >> According to Documentation/devicetree/bindings/usb/fcs,fusb302.txt, the port is mandatory.
>> >> Can it be possible that the problem was that the power port being disabled ?
>> >
>> >Indeed, I believe the OF graph error is just a meaningless annoyance, but the general problem sounds like it's probably the same thing that's come up before:
>> >
>> >https://lore.kernel.org/all/0ac6bbe7-6395-526d-213c-ac58a19d8673@fivetechno.de/
>> >
>> >Disabling CONFIG_TYPEC_FUSB302 or blacklisting the fusb302 module should help confirm that. I have no idea if it's still an open problem, or if it's been fixed and you might just need to define the proper power role in the DT; this just triggered a memory of that older thread :)
>> >
>> >Robin.
>>
>> Yes, the issue above is still there. I therefore use dumb 5 V, 4 A USB power supplies that do not react on the USB-C communication.
>>
>> Markus
>
>@Markus
>Could you try the diff I just send ?
Right on holiday, but will test it next week.
>
>Thanks
>
>_______________________________________________
>Linux-rockchip mailing list
>Linux-rockchip@lists.infradead.org
>http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2022-06-17 12:46 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2022-06-17 9:06 rk3399-roc-pc does not boot Corentin Labbe
2022-06-17 9:58 ` Robin Murphy
2022-06-17 11:35 ` Corentin Labbe
2022-06-17 11:48 ` MR
2022-06-17 11:43 ` MR
2022-06-17 11:47 ` Corentin Labbe
2022-06-17 11:50 ` MR
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).