[PATCH v3 0/3] arm64: dts: imx8mp: add support for the ABB SoM and carrier

[PATCH v3 0/3] arm64: dts: imx8mp: add support for the ABB SoM and carrier

[Heiko Schocher]

The board uses an ABB specific SoM from ADLink, based on NXP
i.MX8MP SoC. The SoM is used on 3 different carrier boards,
with small differences.

series is based on:
819837584309 - (tag: v6.12-rc5, origin/master, origin/HEAD) Linux 6.12-rc5

patches are now checked with

make W=1 dt_binding_check
make W=1 dtbs_check
make W=1 CHECK_DTBS=y {for each dtb introduced in this series)

as Krzysztof suggested.

Changes in v3:
added Reviewed-by from Krzysztof
- worked in comments from Krzysztof
  gpio-line-names should match the actual number of
  gpios of the device.
- added comments from Shawn Guo
  removed unneeded new lines
  sort nodes, properties alphabetical
  rename pcie0-refclk -> clock-xxx
  used GPIO_ACTIVE_HIGH instead of 0
- added comments from Fabio Estevam
  instead of settting each brightness-level in
  brightness-levels add num-interpolated-steps
- changes from me
  fix gpio-line-names for semtech gpio controller
  in imx8mp-aristainetos3-proton2s.dts as patch
  "dt-bindings: pinctrl: sx150xq: allow gpio line naming"
  of this series adds the dtb checks for them and 17 entries
  needed now.

Changes in v2:
reworked the compatible strings for ABB imx8mp based boards
called dtb checks, no errors for this patch
patch dt-bindings: pinctrl: sx150xq: allow gpio line naming new in v2
- worked in comments from Krzysztof
  - removed unneeded dtbos and build now dtbs for each
    carrierboard.
  - removed user spidev entries, as I do not know the
    real spi devices connected to...
  - call dtb check targets as described in cover letter
    and fixed warnings except warnings see below:
not fixed dtb check warnings
- pci (warning pops up for each new dtb from this patch, but
  also for a lot of other boards, which are already in tree)
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg: [[864026624, 4194304], [402653184, 134217728]] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space'] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
- proton2s dtb specific:
  - rs485
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:0: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:1: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: Unevaluated properties are not allowed ('linux,rs485-enabled-at-boot-time', 'rs485-rts-active-low', 'rs485-rts-delay' were unexpected)
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    do not see, what I am doing wrong, also rs485 works fine
  - led driver
    imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']
    I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
    Ah, may because file
    Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
    is not converted to yaml?
  - pinctrl driver
    adding 'gpio-line-names' leads in a warning as this property
    is not checked yet (and so a warning is dropped).
    add this check in new patch
    dt-bindings: pinctrl: sx150xq: allow gpio line naming
    in v2

Heiko Schocher (3):
  dt-bindings: arm: fsl: Add ABB SoM and carrier
  dt-bindings: pinctrl: sx150xq: allow gpio line naming
  arm64: dts: imx8mp: add aristainetos3 board support

 .../devicetree/bindings/arm/fsl.yaml          |    9 +
 .../bindings/pinctrl/semtech,sx1501q.yaml     |   43 +
 arch/arm64/boot/dts/freescale/Makefile        |    5 +
 .../imx8mp-aristainetos3-adpismarc.dts        |   37 +
 .../imx8mp-aristainetos3-helios-lvds.dtso     |  113 ++
 .../freescale/imx8mp-aristainetos3-helios.dts |   98 ++
 .../imx8mp-aristainetos3-proton2s.dts         |  161 +++
 .../imx8mp-aristainetos3a-som-v1.dtsi         | 1107 +++++++++++++++++
 8 files changed, 1573 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi

-- 
2.20.1

[PATCH v3 3/3] arm64: dts: imx8mp: add aristainetos3 board support

[Heiko Schocher]

Add support for the i.MX8MP based aristainetos3 boards from ABB.

The board uses a ABB specific SoM from ADLink, based on NXP
i.MX8MP SoC. The SoM is used on 3 different carrier boards,
with small differences.

Signed-off-by: Heiko Schocher <hs@denx.de>
---

Changes in v3:
- added comments from Shawn Guo
  removed unneeded new lines
  sort nodes, properties alphabetical
  rename pcie0-refclk -> clock-xxx
  used GPIO_ACTIVE_HIGH instead of 0
- added comments from Fabio Estevam
  instead of settting each brightness-level in
  brightness-levels add num-interpolated-steps
- changes from me
  fix gpio-line-names for semtech gpio controller
  in imx8mp-aristainetos3-proton2s.dts as patch
  "dt-bindings: pinctrl: sx150xq: allow gpio line naming"
  of this series adds the dtb checks for them and 17 entries
  needed now.

Changes in v2:
- worked in comments from Krzysztof
  - removed unneeded dtbos and build now dtbs for each
    carrierboard.
  - removed user spidev entries, as I do not know the
    real spi devices connected to...
  - call dtb check targets as described in cover letter
    and fixed warnings except warnings see below:
not fixed dtb check warnings
- pci (warning pops up for each new dtb from this patch, but
  also for a lot of other boards, which are already in tree)
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg: [[864026624, 4194304], [402653184, 134217728]] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space'] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
- proton2s dtb specific:
  - rs485
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:0: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:1: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: Unevaluated properties are not allowed ('linux,rs485-enabled-at-boot-time', 'rs485-rts-active-low', 'rs485-rts-delay' were unexpected)
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    do not see, what I am doing wrong, also rs485 works fine
  - led driver
    imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']
    I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
    Ah, may because file
    Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
    is not converted to yaml?
  - pinctrl driver
    adding 'gpio-line-names' leads in a warning as this property
    is not checked yet (and so a warning is dropped).
    add this check in new patch
    dt-bindings: pinctrl: sx150xq: allow gpio line naming
    in v2

 arch/arm64/boot/dts/freescale/Makefile        |    5 +
 .../imx8mp-aristainetos3-adpismarc.dts        |   37 +
 .../imx8mp-aristainetos3-helios-lvds.dtso     |  113 ++
 .../freescale/imx8mp-aristainetos3-helios.dts |   98 ++
 .../imx8mp-aristainetos3-proton2s.dts         |  161 +++
 .../imx8mp-aristainetos3a-som-v1.dtsi         | 1107 +++++++++++++++++
 6 files changed, 1521 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9d3df8b218a2..40dcd24bf494 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb
 
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3-adpismarc.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3-helios.dtb
+imx8mp-aristainetos3-helios-lvds-dtbs += imx8mp-aristainetos3-helios.dtb imx8mp-aristainetos3-helios-lvds.dtbo
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3-helios-lvds.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3-proton2s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
new file mode 100644
index 000000000000..6a688510dad9
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Heiko Schocher <hs@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx8mp-aristainetos3a-som-v1.dtsi"
+
+&{/} {
+	model = "Aristainetos3 ADLink PI SMARC carrier";
+	compatible = "abb,imx8mp-aristanetos3-adpismarc",
+		     "abb,imx8mp-aristanetos3-som",
+		     "fsl,imx8mp";
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&i2c2 {
+	gpio8: pinctrl@3e {
+		compatible = "semtech,sx1509q";
+		reg = <0x3e>;
+
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		semtech,probe-reset;
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&gpio6>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
new file mode 100644
index 000000000000..9d1f3b4ccc79
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Heiko Schocher <hs@denx.de>
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	model = "Aristainetos3 helios carrier with LVDS";
+	compatible = "abb,imx8mp-aristanetos3-helios",
+		     "abb,imx8mp-aristanetos3-som",
+		     "fsl,imx8mp";
+
+	panel_lvds: panel-lvds {
+		compatible = "lg,lb070wv8";
+		power-supply = <&reg_vcc_disp>;
+		backlight = <&lvds_backlight>;
+
+		port {
+			in_lvds0: endpoint {
+				remote-endpoint = <&ldb_lvds_ch0>;
+			};
+		};
+	};
+
+	reg_vcc_disp: regulator-disp {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd0_vcc_en>;
+		compatible = "regulator-fixed";
+		regulator-name = "disp_power_en_2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&gpio3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio3_hog>;
+
+	lvdssel-hog {
+		gpio-hog;
+		gpios = <23 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "LVDSSEL";
+	};
+};
+
+&hdmi_blk_ctrl {
+	status = "disabled";
+};
+
+&hdmi_pvi {
+	status = "disabled";
+};
+
+&hdmi_tx {
+	status = "disabled";
+};
+
+&hdmi_tx_phy {
+	status = "disabled";
+};
+
+&irqsteer_hdmi {
+	status = "disabled";
+};
+
+&ldb_lvds_ch0 {
+	remote-endpoint = <&in_lvds0>;
+};
+
+&lcdif1 {
+	status = "disabled";
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lcdif3 {
+	status = "disabled";
+};
+
+&lvds_backlight {
+	status = "okay";
+};
+
+&lvds_bridge {
+	/* IMX8MP_CLK_MEDIA_LDB = IMX8MP_CLK_MEDIA_DISP2_PIX * 7 */
+	assigned-clock-rates = <232820000>;
+	status = "okay";
+};
+
+&media_blk_ctrl {
+	/*
+	 * currently it is not possible to let display clocks configure
+	 * automatically, so we need to set them manually
+	 */
+	assigned-clock-rates = <500000000>, <200000000>, <0>,
+		/* IMX8MP_CLK_MEDIA_DISP2_PIX = pixelclk of lvds panel */
+		<33260000>, <0>,
+		/* IMX8MP_VIDEO_PLL1 = IMX8MP_CLK_MEDIA_LDB * 2 */
+		<465640000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
new file mode 100644
index 000000000000..a4e649a8239b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Heiko Schocher <hs@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mp-aristainetos3a-som-v1.dtsi"
+
+&{/} {
+	model = "Aristainetos3 helios carrier";
+	compatible = "abb,imx8mp-aristanetos3-helios",
+		     "abb,imx8mp-aristanetos3-som",
+		     "fsl,imx8mp";
+
+	led-controller {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			function-enumerator = <20>;
+			gpios = <&pca6416 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			function-enumerator = <20>;
+			gpios = <&pca6416 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <20>;
+			gpios = <&pca6416 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-3 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			function-enumerator = <20>;
+			gpios = <&pca6416 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&ethphy1 {
+	status = "disabled";
+};
+
+&fec {
+	status = "disabled";
+};
+
+&i2c1 {
+	eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+	};
+};
+
+&i2c3 {
+	pca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "DIN0_CON",
+			"DIN1_CON",
+			"DIN2_CON",
+			"DIN3_CON",
+			"DIN4_CON",
+			"DIN5_CON",
+			"DIN6_CON",
+			"DIN7_CON",
+			"PM102_RES",
+			"COMx_RES",
+			"BPL_RES",
+			"PC_RES",
+			"LED_RED",
+			"LED_YELLOW",
+			"LED_GREEN",
+			"LED_BLUE";
+	};
+
+	rtc@68 {
+		compatible = "st,m41t00";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
new file mode 100644
index 000000000000..2a736dbe96b4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Heiko Schocher <hs@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx8mp-aristainetos3a-som-v1.dtsi"
+
+&{/} {
+	model = "Aristainetos3 proton2s carrier";
+	compatible = "abb,imx8mp-aristanetos3-proton2s",
+		     "abb,imx8mp-aristanetos3-som",
+		     "fsl,imx8mp";
+
+	watchdog {
+		/* MAX6371KA */
+		compatible = "linux,wdt-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_watchdog_gpio>;
+		always-running;
+		gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		hw_algo = "level";
+		/* Reset triggers in 3..9 seconds */
+		hw_margin_ms = <1500>;
+	};
+};
+
+&ethphy1 {
+	status = "disabled";
+};
+
+&eqos {
+	max-speed = <100>;
+};
+
+&ecspi1{
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+};
+
+&fec {
+	status = "disabled";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_proton2s>;
+
+	gpio-line-names =
+		"", "", "", "", "", "", "", "POWER",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"RELAY0", "RELAY1", "RELAY2", "HEATER",
+		"FAN", "SPARE",	"CLEAR", "FAULT",
+		"", "", "", "", "", "", "", "", "";
+};
+
+&i2c2 {
+	tlc59108@40 {
+		compatible = "ti,tlc59108";
+		reg = <0x40>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0x0>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			function-enumerator = <20>;
+		};
+
+		led@1 {
+			reg = <0x1>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <20>;
+		};
+
+		led@2 {
+			reg = <0x2>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <21>;
+		};
+
+		led@3 {
+			reg = <0x3>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			function-enumerator = <21>;
+		};
+
+		led@4 {
+			reg = <0x4>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			function-enumerator = <21>;
+		};
+
+		led@5 {
+			reg = <0x5>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			function-enumerator = <22>;
+		};
+
+		led@6 {
+			reg = <0x6>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			function-enumerator = <22>;
+		};
+
+		led@7 {
+			reg = <0x7>;
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			function-enumerator = <22>;
+		};
+	};
+
+	rtc1: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
+&uart3 {
+	pinctrl-0 = <&pinctrl_uart3>;
+};
+
+&uart4 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rts-delay = <0 0>;
+	rts-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usdhc1 {
+	status = "disabled";
+};
+
+&wdog1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi
new file mode 100644
index 000000000000..231e480acfd4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi
@@ -0,0 +1,1107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2024 Heiko Schocher <hs@denx.de>
+ */
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8mp.dtsi"
+
+/ {
+	model = "ADLINK LEC-iMX8MP-Q-N-4G-32G";
+	compatible = "abb,imx8mp-aristanetos3-som", "fsl,imx8mp";
+
+	aliases {
+		ethernet0 = &eqos;
+		ethernet1 = &fec;
+		mmc0 = &usdhc3;	/* eMMC */
+		mmc1 = &usdhc2;	/* MicroSD */
+	};
+
+	chosen {
+		bootargs = "console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200";
+		stdout-path = &uart2;
+	};
+
+	connector {
+		compatible = "usb-c-connector";
+		label = "USB-C";
+
+		port {
+			usb_dr_connector: endpoint {
+				remote-endpoint = <&usb3_dwc>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			function-enumerator = <0>;
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	lvds_backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lvds_bklt_en>;
+		pwms = <&pwm2 0 50000 0>;
+		enable-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <80>;
+		status = "disabled";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		/* Memory size 512 MiB..8 GiB will be filled by U-Boot */
+		reg = <0x0 0x40000000 0 0x08000000>;
+	};
+
+	pcie0_refclk: clock-pcie-ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan1_reg>;
+		gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "can1-stby";
+	};
+
+	reg_can2_stby: regulator-can2-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan2_reg>;
+		enable-active-high;
+		gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "can2-stby";
+	};
+
+	reg_dp83867_2v5: regulator-enet {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "enet_2v5";
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_usb1_host_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_vbus>;
+		enable-active-high;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb1_host_vbus";
+		regulator-always-on;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_vmmc>;
+		enable-active-high;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; /* SD2_RESET */
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD_3V3_SD";
+		off-on-delay-us = <12000>;
+		startup-delay-us = <100>;
+		vin-supply = <&buck4>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&clk {
+	clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>,
+		 <&clk_ext3>, <&clk_ext4>;
+	clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
+		      "clk_ext3", "clk_ext4";
+	assigned-clocks = <&clk IMX8MP_CLK_A53_SRC>,
+			  <&clk IMX8MP_CLK_A53_CORE>,
+			  <&clk IMX8MP_CLK_NOC>,
+			  <&clk IMX8MP_CLK_NOC_IO>,
+			  <&clk IMX8MP_CLK_GIC>,
+			  <&clk IMX8MP_CLK_AUDIO_AHB>,
+			  <&clk IMX8MP_CLK_AUDIO_AXI_SRC>,
+			  <&clk IMX8MP_AUDIO_PLL1>,
+			  <&clk IMX8MP_AUDIO_PLL2>,
+			  <&clk IMX8MP_VIDEO_PLL1>;
+};
+
+&ecspi1{
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs2>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW &gpio1 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* eth0 */
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos_rgmii>;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	snps,force_thresh_dma_mode;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: eqos-ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,min-output-impedance;
+			ti,dp83867-rxctrl-strap-quirk;
+			interrupt-parent = <&gpio4>;
+			interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <5>;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <5>;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+			snps,map-to-dma-channel = <0>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+			snps,map-to-dma-channel = <1>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+			snps,map-to-dma-channel = <2>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+			snps,map-to-dma-channel = <3>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+			snps,map-to-dma-channel = <4>;
+		};
+	};
+};
+
+/* eth1 */
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec_rgmii>;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpio = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,min-output-impedance;
+			ti,dp83867-rxctrl-strap-quirk;
+			eee-broken-1000t;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "disabled";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "disabled";
+};
+
+&hdmi_blk_ctrl {
+	status = "okay";
+};
+
+&hdmi_pvi {
+	status = "okay";
+};
+
+&hdmi_tx {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	status = "okay";
+};
+
+&hdmi_tx_phy {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+		/*
+		 * i.MX 8M Plus Data Sheet for Consumer Products
+		 * 3.1.4 Operating ranges
+		 * MIMX8ML8CVNKZAB
+		 */
+		regulators {
+			buck1: BUCK1 {	/* VDD_SOC (dual-phase with BUCK3) */
+				regulator-name = "buck1";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2: BUCK2 {	/* VDD_ARM */
+				regulator-name = "buck2";
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck4: BUCK4 {	/* VDD_3V3 */
+				regulator-name = "buck4";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck5: BUCK5 {	/* VDD_1V8 */
+				regulator-name = "buck5";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck6: BUCK6 {	/* NVCC_DRAM_1V1 */
+				regulator-name = "buck6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo1: LDO1 {	/* NVCC_SNVS_1V8 */
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo2: LDO2 {	/* VDDA_1V8 */
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo3: LDO3 {	/* VDDA_1V8 */
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4: LDO4 {	/* PMIC_LDO4 */
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo5: LDO5 {	/* NVCC_SD2 */
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio5 19 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&i2c5 {
+	#address-cells = <1>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c5>;
+	status = "okay";
+};
+
+&i2c6 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c6>;
+	pinctrl-1 = <&pinctrl_i2c6_gpio>;
+	scl-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	/* TPM - ST33TPHF2XI2C U2301 */
+	tpm: tpm@2e {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tpm_irq>;
+		compatible = "st,st33ktpm2xi2c", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+
+		label = "tpm";
+		interrupt-parent = <&gpio3>;
+		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
+
+	/* SX1509(0) U2605 */
+	gpio6: pinctrl@3f {
+		compatible = "semtech,sx1509q";
+		reg = <0x3f>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		semtech,probe-reset;
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	/* RTC U2607 */
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+	};
+
+	/* SX1509(1) U2606 */
+	gpio7: pinctrl@70 {
+		compatible = "semtech,sx1509q";
+		reg = <0x70>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		semtech,probe-reset;
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&gpio4>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio6-cfg {
+			pins = "gpio6";
+			output-high;
+		};
+
+		gpio7-cfg {
+			pins = "gpio7";
+			output-high;
+		};
+	};
+};
+
+&irqsteer_hdmi {
+	status = "okay";
+};
+
+&lcdif1 {
+	status = "disabled";
+};
+
+&lcdif2 {
+	status = "disabled";
+};
+
+/* HDMI */
+&lcdif3 {
+	status = "okay";
+
+};
+
+&lvds_bridge {
+	status = "disabled";
+};
+
+&mipi_dsi {
+	status = "disabled";
+};
+
+&pcie{
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 20 GPIO_ACTIVE_LOW>;
+	fsl,tx-deemph-gen1 = <0x1f>;
+	fsl,max-link-speed = <3>;
+	status = "okay";
+};
+
+&pcie_phy{
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	#pwm-cells = <3>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	dr_mode = "otg";
+	usb-role-switch;
+	role-switch-default-mode = "peripheral";
+	status = "okay";
+
+	port {
+		usb3_dwc: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+/* SD slot */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	vmmc-supply = <&buck4>;
+	vqmmc-supply = <&buck5>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: aristainetos3-ecspi1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK		0x82
+			MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI		0x82
+			MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO		0x82
+			MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09		0x40000
+		>;
+	};
+
+	pinctrl_ecspi1_cs2: aristainetos3-ecspi1-cs2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x40000
+		>;
+	};
+
+	pinctrl_ecspi2: aristainetos3-ecspi2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK		0x82
+			MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI		0x82
+			MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO		0x82
+			MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x40000
+		>;
+	};
+
+	pinctrl_eqos_rgmii: aristainetos3-eqos-rgmii-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x19
+		>;
+	};
+
+	pinctrl_fec_rgmii: aristainetos3-fec-rgmii-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
+			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x19
+		>;
+	};
+
+	pinctrl_flexcan1: aristainetos3-flexcan1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_RX__CAN1_RX			0x154
+			MX8MP_IOMUXC_SPDIF_TX__CAN1_TX			0x154
+		>;
+	};
+
+	pinctrl_flexcan1_reg: aristainetos3-flexcan1-reg-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05  0x154
+		>;
+	};
+
+	pinctrl_flexcan2: aristainetos3-flexcan2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX         0x154
+			MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX         0x154
+		>;
+	};
+
+	pinctrl_flexcan2_reg: aristainetos3-flexcan2-reg-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27      0x154
+		>;
+	};
+
+	pinctrl_gpio3_hog: aristainetos3-gpio3-hog-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23	0xd6
+		>;
+	};
+
+	pinctrl_gpio_led: aristainetos3-gpio-led-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x19
+		>;
+	};
+
+	pinctrl_gpio_proton2s: aristainetos3-gpio-proton2s-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07	0x19
+		>;
+	};
+
+	pinctrl_hdmi: aristainetos3-hdmi-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL	0x400001c3
+			MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA	0x400001c3
+			MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD		0x40000019
+			MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC		0x40000019
+		>;
+	};
+
+	pinctrl_i2c1: aristainetos3-i2c1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c1_gpio: aristainetos3-i2c1-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14	0x1c3
+			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15	0x1c3
+		>;
+	};
+
+	pinctrl_i2c2: aristainetos3-i2c2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2_gpio: aristainetos3-i2c2-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1c3
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1c3
+		>;
+	};
+
+	pinctrl_i2c3: aristainetos3-i2c3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3_gpio: aristainetos3-i2c3-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18	0x1c3
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19	0x1c3
+		>;
+	};
+
+	pinctrl_i2c5: aristainetos3-i2c5-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL	0x400001c3
+			MX8MP_IOMUXC_SAI5_MCLK__I2C5_SDA	0x400001c3
+		>;
+	};
+
+	pinctrl_i2c6: aristainetos3-i2c6-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL	0x400001c3
+			MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c6_gpio: aristainetos3-i2c6-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19	0x1c3
+			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20	0x1c3
+		>;
+	};
+
+	pinctrl_lcd0_vcc_en: aristainetos3-lcd0-vcc-en-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13	0xd6
+		>;
+	};
+
+	pinctrl_lvds_bklt_en: aristainetos3-lvds-bklt-en-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10	0xd6
+		>;
+	};
+
+	pinctrl_pcie: aristainetos3-pcie-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__PCIE_CLKREQ_B	0x61
+			MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20	0x41
+		>;
+	};
+
+	pinctrl_pmic: aristainetos3-pmic-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03	0x41
+		>;
+	};
+
+	pinctrl_pwm1: aristainetos3-pwm1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO01__PWM1_OUT	0x116
+		>;
+	};
+
+	pinctrl_pwm2: aristainetos3-pwm2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO11__PWM2_OUT	0x116
+		>;
+	};
+
+	pinctrl_tpm_irq: aristainetos3-tpm-irq-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14	0xd6
+		>;
+	};
+
+	pinctrl_uart1: aristainetos3-uart1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart2: aristainetos3-uart2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
+			MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06	0x140
+			MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS	0x140
+		>;
+	};
+
+	pinctrl_uart3: aristainetos3-uart3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_ALE__UART3_DCE_RX	0x140
+			MX8MP_IOMUXC_NAND_CE0_B__UART3_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart4: aristainetos3-uart4-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX    0x140
+			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX    0x140
+			MX8MP_IOMUXC_NAND_DATA03__GPIO3_IO09	0x140
+			MX8MP_IOMUXC_NAND_DATA02__UART4_DCE_CTS 0x140
+		>;
+	};
+
+	pinctrl_usb1_vbus: aristainetos3-usb1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14	0x19
+		>;
+	};
+
+	pinctrl_usdhc1: aristainetos3-usdhc1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: aristainetos3-usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x194
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d4
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d4
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d4
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d4
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: aristainetos3-usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x196
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d6
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d6
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d6
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d6
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2: aristainetos3-usdhc2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: aristainetos3-usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: aristainetos3-usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: aristainetos3-usdhc2-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x40000080
+		>;
+	};
+
+	pinctrl_usdhc2_vmmc: aristainetos3-usdhc2-vmmc-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+		>;
+	};
+
+	pinctrl_usdhc3: aristainetos3-usdhc3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: aristainetos3-usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: aristainetos3-usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_watchdog_gpio: aristainetos3-wdog-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06	0x19
+		>;
+	};
+
+	pinctrl_wdog: aristainetos3-wdog-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
-- 
2.20.1

Re: [PATCH v3 0/3] arm64: dts: imx8mp: add support for the ABB SoM and carrier

[Rob Herring (Arm)]

On Tue, 05 Nov 2024 07:42:03 +0100, Heiko Schocher wrote:
> The board uses an ABB specific SoM from ADLink, based on NXP
> i.MX8MP SoC. The SoM is used on 3 different carrier boards,
> with small differences.
> 
> series is based on:
> 819837584309 - (tag: v6.12-rc5, origin/master, origin/HEAD) Linux 6.12-rc5
> 
> patches are now checked with
> 
> make W=1 dt_binding_check
> make W=1 dtbs_check
> make W=1 CHECK_DTBS=y {for each dtb introduced in this series)
> 
> as Krzysztof suggested.
> 
> Changes in v3:
> added Reviewed-by from Krzysztof
> - worked in comments from Krzysztof
>   gpio-line-names should match the actual number of
>   gpios of the device.
> - added comments from Shawn Guo
>   removed unneeded new lines
>   sort nodes, properties alphabetical
>   rename pcie0-refclk -> clock-xxx
>   used GPIO_ACTIVE_HIGH instead of 0
> - added comments from Fabio Estevam
>   instead of settting each brightness-level in
>   brightness-levels add num-interpolated-steps
> - changes from me
>   fix gpio-line-names for semtech gpio controller
>   in imx8mp-aristainetos3-proton2s.dts as patch
>   "dt-bindings: pinctrl: sx150xq: allow gpio line naming"
>   of this series adds the dtb checks for them and 17 entries
>   needed now.
> 
> Changes in v2:
> reworked the compatible strings for ABB imx8mp based boards
> called dtb checks, no errors for this patch
> patch dt-bindings: pinctrl: sx150xq: allow gpio line naming new in v2
> - worked in comments from Krzysztof
>   - removed unneeded dtbos and build now dtbs for each
>     carrierboard.
>   - removed user spidev entries, as I do not know the
>     real spi devices connected to...
>   - call dtb check targets as described in cover letter
>     and fixed warnings except warnings see below:
> not fixed dtb check warnings
> - pci (warning pops up for each new dtb from this patch, but
>   also for a lot of other boards, which are already in tree)
> imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg: [[864026624, 4194304], [402653184, 134217728]] is too short
>         from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
> imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space'] is too short
>         from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
> - proton2s dtb specific:
>   - rs485
>     imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:0: 0 is not of type 'array'
>         from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>     imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:1: 0 is not of type 'array'
>         from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>     imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: Unevaluated properties are not allowed ('linux,rs485-enabled-at-boot-time', 'rs485-rts-active-low', 'rs485-rts-delay' were unexpected)
>         from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>     do not see, what I am doing wrong, also rs485 works fine
>   - led driver
>     imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']
>     I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
>     Ah, may because file
>     Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
>     is not converted to yaml?
>   - pinctrl driver
>     adding 'gpio-line-names' leads in a warning as this property
>     is not checked yet (and so a warning is dropped).
>     add this check in new patch
>     dt-bindings: pinctrl: sx150xq: allow gpio line naming
>     in v2
> 
> Heiko Schocher (3):
>   dt-bindings: arm: fsl: Add ABB SoM and carrier
>   dt-bindings: pinctrl: sx150xq: allow gpio line naming
>   arm64: dts: imx8mp: add aristainetos3 board support
> 
>  .../devicetree/bindings/arm/fsl.yaml          |    9 +
>  .../bindings/pinctrl/semtech,sx1501q.yaml     |   43 +
>  arch/arm64/boot/dts/freescale/Makefile        |    5 +
>  .../imx8mp-aristainetos3-adpismarc.dts        |   37 +
>  .../imx8mp-aristainetos3-helios-lvds.dtso     |  113 ++
>  .../freescale/imx8mp-aristainetos3-helios.dts |   98 ++
>  .../imx8mp-aristainetos3-proton2s.dts         |  161 +++
>  .../imx8mp-aristainetos3a-som-v1.dtsi         | 1107 +++++++++++++++++
>  8 files changed, 1573 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi
> 
> --
> 2.20.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y freescale/imx8mp-aristainetos3-adpismarc.dtb freescale/imx8mp-aristainetos3-helios.dtb freescale/imx8mp-aristainetos3-proton2s.dtb' for 20241105064206.43626-1-hs@denx.de:

arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']

Re: [PATCH v3 0/3] arm64: dts: imx8mp: add support for the ABB SoM and carrier

[Heiko Schocher]

Hello Rob,

On 05.11.24 14:11, Rob Herring (Arm) wrote:
> 
> On Tue, 05 Nov 2024 07:42:03 +0100, Heiko Schocher wrote:
>> The board uses an ABB specific SoM from ADLink, based on NXP
>> i.MX8MP SoC. The SoM is used on 3 different carrier boards,
>> with small differences.
>>
>> series is based on:
>> 819837584309 - (tag: v6.12-rc5, origin/master, origin/HEAD) Linux 6.12-rc5
>>
>> patches are now checked with
>>
>> make W=1 dt_binding_check
>> make W=1 dtbs_check
>> make W=1 CHECK_DTBS=y {for each dtb introduced in this series)
>>
>> as Krzysztof suggested.
>>
>> Changes in v3:
>> added Reviewed-by from Krzysztof
>> - worked in comments from Krzysztof
>>    gpio-line-names should match the actual number of
>>    gpios of the device.
>> - added comments from Shawn Guo
>>    removed unneeded new lines
>>    sort nodes, properties alphabetical
>>    rename pcie0-refclk -> clock-xxx
>>    used GPIO_ACTIVE_HIGH instead of 0
>> - added comments from Fabio Estevam
>>    instead of settting each brightness-level in
>>    brightness-levels add num-interpolated-steps
>> - changes from me
>>    fix gpio-line-names for semtech gpio controller
>>    in imx8mp-aristainetos3-proton2s.dts as patch
>>    "dt-bindings: pinctrl: sx150xq: allow gpio line naming"
>>    of this series adds the dtb checks for them and 17 entries
>>    needed now.
>>
>> Changes in v2:
>> reworked the compatible strings for ABB imx8mp based boards
>> called dtb checks, no errors for this patch
>> patch dt-bindings: pinctrl: sx150xq: allow gpio line naming new in v2
>> - worked in comments from Krzysztof
>>    - removed unneeded dtbos and build now dtbs for each
>>      carrierboard.
>>    - removed user spidev entries, as I do not know the
>>      real spi devices connected to...
>>    - call dtb check targets as described in cover letter
>>      and fixed warnings except warnings see below:
>> not fixed dtb check warnings
>> - pci (warning pops up for each new dtb from this patch, but
>>    also for a lot of other boards, which are already in tree)
>> imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg: [[864026624, 4194304], [402653184, 134217728]] is too short
>>          from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
>> imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space'] is too short
>>          from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
>> - proton2s dtb specific:
>>    - rs485
>>      imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:0: 0 is not of type 'array'
>>          from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>>      imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:1: 0 is not of type 'array'
>>          from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>>      imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: Unevaluated properties are not allowed ('linux,rs485-enabled-at-boot-time', 'rs485-rts-active-low', 'rs485-rts-delay' were unexpected)
>>          from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
>>      do not see, what I am doing wrong, also rs485 works fine
>>    - led driver
>>      imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']
>>      I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
>>      Ah, may because file
>>      Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
>>      is not converted to yaml?
>>    - pinctrl driver
>>      adding 'gpio-line-names' leads in a warning as this property
>>      is not checked yet (and so a warning is dropped).
>>      add this check in new patch
>>      dt-bindings: pinctrl: sx150xq: allow gpio line naming
>>      in v2
>>
>> Heiko Schocher (3):
>>    dt-bindings: arm: fsl: Add ABB SoM and carrier
>>    dt-bindings: pinctrl: sx150xq: allow gpio line naming
>>    arm64: dts: imx8mp: add aristainetos3 board support
>>
>>   .../devicetree/bindings/arm/fsl.yaml          |    9 +
>>   .../bindings/pinctrl/semtech,sx1501q.yaml     |   43 +
>>   arch/arm64/boot/dts/freescale/Makefile        |    5 +
>>   .../imx8mp-aristainetos3-adpismarc.dts        |   37 +
>>   .../imx8mp-aristainetos3-helios-lvds.dtso     |  113 ++
>>   .../freescale/imx8mp-aristainetos3-helios.dts |   98 ++
>>   .../imx8mp-aristainetos3-proton2s.dts         |  161 +++
>>   .../imx8mp-aristainetos3a-som-v1.dtsi         | 1107 +++++++++++++++++
>>   8 files changed, 1573 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
>>   create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
>>   create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
>>   create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
>>   create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi
>>
>> --
>> 2.20.1
>>
>>
>>
> 
> 
> My bot found new DTB warnings on the .dts files added or changed in this
> series.
> 
> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> are fixed by another series. Ultimately, it is up to the platform
> maintainer whether these warnings are acceptable or not. No need to reply
> unless the platform maintainer has comments.
> 
> If you already ran DT checks and didn't see these error(s), then
> make sure dt-schema is up to date:
> 
>    pip3 install dtschema --upgrade
> 
> 
> New warnings running 'make CHECK_DTBS=y freescale/imx8mp-aristainetos3-adpismarc.dtb freescale/imx8mp-aristainetos3-helios.dtb freescale/imx8mp-aristainetos3-proton2s.dtb' for 20241105064206.43626-1-hs@denx.de:
> 
> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']

Yep, reason I explained above in commit comment:

 >>    - led driver
 >>      imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to 
match any schema with compatible: ['ti,tlc59108']
 >>      I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
 >>      Ah, may because file
 >>      Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
 >>      is not converted to yaml?

So the compatible entry is fully okay, just the check is poping up,
as yaml file is missing...

bye,
Heiko
-- 
DENX Software Engineering GmbH,      Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs@denx.de

Re: [PATCH v3 3/3] arm64: dts: imx8mp: add aristainetos3 board support

[Shawn Guo]

On Tue, Nov 05, 2024 at 07:42:06AM +0100, Heiko Schocher wrote:
> Add support for the i.MX8MP based aristainetos3 boards from ABB.
> 
> The board uses a ABB specific SoM from ADLink, based on NXP
> i.MX8MP SoC. The SoM is used on 3 different carrier boards,
> with small differences.
> 
> Signed-off-by: Heiko Schocher <hs@denx.de>

Applied, thanks!