Re: [PATCH v2] PCI: dw-rockchip: Enable async probe by default

[Niklas Cassel <cassel@kernel.org>]

On Fri, Jan 03, 2025 at 08:59:51PM +0530, Anand Moon wrote:
> Hi Niklas
> 
> On Fri, 3 Jan 2025 at 20:40, Niklas Cassel <cassel@kernel.org> wrote:
> >
> > On Fri, Jan 03, 2025 at 08:36:18PM +0530, Anand Moon wrote:
> > > > >
> > > > > We need to enable the GMAC PHY and reset it using the proper GPIO pin
> > > > > (PCIE_PERST_L).
> > > > > Please refer to the schematic for more details.
> > > >
> > > > The PERST# GPIO is already asserted + deasserted from the PCIe Root Complex
> > > > (host) driver:
> > > > https://github.com/torvalds/linux/blob/v6.13-rc5/drivers/pci/controller/dwc/pcie-dw-rockchip.c#L191-L206
> > > >
> > > > which will cause the endpoint device (a RTL8125 NIC in this case)
> > > > to be reset during bootup.
> > > >
> > > Thanks for letting me know. It seems like a workaround.
> > > I'll try to disable this and test it again.
> > >
> > > My point is that we haven't enabled the GMAC PHY (device nodes)
> > > and must properly reset the GMAC.
> > >
> > > We're relying on the code above hack to do that job.
> >
> > I do not think it is a hack.
> >
> > If you look in most PCIe controller drivers, they toggle PERST before
> > enumerating the bus:
> > $ git grep gpiod_set_value drivers/pci/controller/
> >
> 
> Ok, understood. However, we have multiple reset lines per controller,
> so the PCIe driver will reset these lines using gpiod_set_value.
> 
> PCIE30X4_PERSTn_M1_L
> PCIE30x1_0_PERSTn_M1_L
> PCIE_PERST_L

If you look in Documentation/devicetree/bindings/pci/pci.txt

You will see:
"""
- reset-gpios:
   If present this property specifies PERST# GPIO. Host drivers can parse the
   GPIO and apply fundamental reset to endpoints.
"""

For rock5b, reset-gpios/PERST# pins are defined in:
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts

$ git grep -p reset-gpio arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts=&pcie2x1l0 {
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts:        reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts=&pcie2x1l2 {
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts:        reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>;
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts=&pcie3x4 {
arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts:        reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;

So I think there is just one reset line per controller.


Kind regards,
Niklas