[PATCH] media: c8sectpfe: switch to using gpiod API

[PATCH] media: c8sectpfe: switch to using gpiod API

[Dmitry Torokhov]

This switches the driver from using legacy gpio API and to the newer
gpiod API. Since ordinary gpiod APIs operate on logical and not
electrical levels, handling of the reset GPIO is adjusted accordingly.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
 .../st/sti/c8sectpfe/c8sectpfe-core.c         | 31 ++++++++-----------
 .../st/sti/c8sectpfe/c8sectpfe-core.h         |  4 ++-
 2 files changed, 16 insertions(+), 19 deletions(-)

diff --git a/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.c b/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.c
index c38b62d4f1ae..dd8141e0828d 100644
--- a/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.c
+++ b/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.c
@@ -16,8 +16,10 @@
 #include <linux/dma-mapping.h>
 #include <linux/dvb/dmx.h>
 #include <linux/dvb/frontend.h>
+#include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
@@ -812,30 +814,23 @@ static int c8sectpfe_probe(struct platform_device *pdev)
 		}
 		of_node_put(i2c_bus);
 
-		tsin->rst_gpio = of_get_named_gpio(child, "reset-gpios", 0);
-
-		ret = gpio_is_valid(tsin->rst_gpio);
-		if (!ret) {
-			dev_err(dev,
-				"reset gpio for tsin%d not valid (gpio=%d)\n",
-				tsin->tsin_id, tsin->rst_gpio);
-			ret = -EINVAL;
-			goto err_node_put;
-		}
-
-		ret = devm_gpio_request_one(dev, tsin->rst_gpio,
-					GPIOF_OUT_INIT_LOW, "NIM reset");
+		/* Acquire reset GPIO and activate it */
+		tsin->rst_gpio = devm_fwnode_gpiod_get(dev,
+						       of_fwnode_handle(child),
+						       "reset", GPIOD_OUT_HIGH,
+						       "NIM reset");
+		ret = PTR_ERR_OR_ZERO(tsin->rst_gpio);
 		if (ret && ret != -EBUSY) {
-			dev_err(dev, "Can't request tsin%d reset gpio\n"
-				, fei->channel_data[index]->tsin_id);
+			dev_err(dev, "Can't request tsin%d reset gpio\n",
+				fei->channel_data[index]->tsin_id);
 			goto err_node_put;
 		}
 
 		if (!ret) {
-			/* toggle reset lines */
-			gpio_direction_output(tsin->rst_gpio, 0);
+			/* wait for the chip to reset */
 			usleep_range(3500, 5000);
-			gpio_direction_output(tsin->rst_gpio, 1);
+			/* release the reset line */
+			gpiod_set_value_cansleep(tsin->rst_gpio, 0);
 			usleep_range(3000, 5000);
 		}
 
diff --git a/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.h b/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.h
index c9d6021904cd..bf377cc82225 100644
--- a/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.h
+++ b/drivers/media/platform/st/sti/c8sectpfe/c8sectpfe-core.h
@@ -16,6 +16,8 @@
 
 #define C8SECTPFE_MAX_TSIN_CHAN 8
 
+struct gpio_desc;
+
 struct channel_info {
 
 	int tsin_id;
@@ -25,7 +27,7 @@ struct channel_info {
 	int i2c;
 	int dvb_card;
 
-	int rst_gpio;
+	struct gpio_desc *rst_gpio;
 
 	struct i2c_adapter  *i2c_adapter;
 	struct i2c_adapter  *tuner_i2c;
-- 
2.39.1.519.gcb327c4b5f-goog


-- 
Dmitry

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH] media: c8sectpfe: switch to using gpiod API

[Andy Shevchenko]

On Fri, Feb 03, 2023 at 03:13:48PM -0800, Dmitry Torokhov wrote:
> This switches the driver from using legacy gpio API and to the newer
> gpiod API. Since ordinary gpiod APIs operate on logical and not
> electrical levels, handling of the reset GPIO is adjusted accordingly.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

This is an important patch for the further cleanups in the GPIO subsystem.
Can we have this applied, please?

-- 
With Best Regards,
Andy Shevchenko



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel