Re: [PATCH net-next v3 5/7] net: dsa: mt7530: simplify mt7530_setup_port6() and change to void

From: "Russell King (Oracle)" <linux@armlinux.org.uk>
To: arinc.unal@arinc9.com
Cc: Daniel Golle <daniel@makrotopia.org>,
	DENG Qingfang <dqfext@gmail.com>,
	Sean Wang <sean.wang@mediatek.com>, Andrew Lunn <andrew@lunn.ch>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Vladimir Oltean <olteanv@gmail.com>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Matthias Brugger <matthias.bgg@gmail.com>,
	AngeloGioacchino Del Regno
	<angelogioacchino.delregno@collabora.com>,
	mithat.guner@xeront.com, erkin.bozoglu@xeront.com,
	Bartel Eerdekens <bartel.eerdekens@constell8.be>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-mediatek@lists.infradead.org
Subject: Re: [PATCH net-next v3 5/7] net: dsa: mt7530: simplify mt7530_setup_port6() and change to void
Date: Fri, 2 Feb 2024 11:51:09 +0000	[thread overview]
Message-ID: <ZbzXLZ4ZyPSbqkdg@shell.armlinux.org.uk> (raw)
In-Reply-To: <20240202-for-netnext-mt7530-improvements-2-v3-5-63d5adae99ca@arinc9.com>

On Fri, Feb 02, 2024 at 12:19:11PM +0300, Arınç ÜNAL via B4 Relay wrote:
> From: Arınç ÜNAL <arinc.unal@arinc9.com>
> 
> This code is from before this driver was converted to phylink API. Phylink
> deals with the unsupported interface cases before mt7530_setup_port6() is
> run. Therefore, the default case would never run. However, it must be
> defined nonetheless to handle all the remaining enumeration values, the
> phy-modes.
> 
> Switch to if statement for RGMII and return which simplifies the code and
> saves an indent.
> 
> Set P6_INTF_MODE, which is the the three least significant bits of the
> MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
> after reset. This is to keep supporting dynamic reconfiguration of the port
> in the case the interface changes from TRGMII to RGMII.
> 
> Disable the TRGMII clocks for all cases. They will be enabled if TRGMII is
> being used.
> 
> Read XTAL after checking for RGMII as it's only needed for the TRGMII
> interface mode.
> 
> Change mt7530_setup_port6() to void now that there're no error cases left.
> 
> Reviewed-by: Daniel Golle <daniel@makrotopia.org>
> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>

Yay. Less possible errors in mac_config()!

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Thanks!

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel