* [PATCH v2 1/2] dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board
2024-01-24 14:13 [PATCH v2 0/2] nxp: imx: Add support for Apalis Evaluation Board v1.2 Hiago De Franco
@ 2024-01-24 14:13 ` Hiago De Franco
2024-01-24 14:13 ` [PATCH v2 2/2] arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2 Hiago De Franco
2024-02-06 7:40 ` [PATCH v2 0/2] " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Hiago De Franco @ 2024-01-24 14:13 UTC (permalink / raw)
To: Shawn Guo, linux-arm-kernel
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, Hiago De Franco, Conor Dooley
From: Hiago De Franco <hiago.franco@toradex.com>
Add the toradex,apalis_imx6q-eval-v1.2 compatible string for version 1.2
of the Apalis Evaluation Board.
Version v1.2 includes the following changes compared to v1.1:
- 8-bit MMC connector replaced with a 4-bit uSD connector.
- Audio codec NAU88C22 added.
- M24C02 EEPROM i2c added.
- MIPI-CSI-2 connector directly to the board added.
- PCIe switch PEX8605 removed and PCIe now is routed directly to Mini
PCIe connector.
- Power measurement IC INA219 added.
- Replaced DVI with HDMI connector.
- Single-channel USB to UART converter replaced with four-channel USB
to UART/JTAG.
- Temperature sensor TMP75 added.
Please note that version v1.0 (which reached EOL) is compatible with
v1.1, therefore toradex,apalis_imx6q-eval compatible string should be
used for both v1.0 and v1.1.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
---
v2:
- Add Acked-by: Conor Dooley.
---
Documentation/devicetree/bindings/arm/fsl.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 228dcc5c7d6f..9502a2946071 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -384,7 +384,8 @@ properties:
- toradex,apalis_imx6q-ixora # Apalis iMX6Q/D Module on Ixora Carrier Board
- toradex,apalis_imx6q-ixora-v1.1 # Apalis iMX6Q/D Module on Ixora V1.1 Carrier Board
- toradex,apalis_imx6q-ixora-v1.2 # Apalis iMX6Q/D Module on Ixora V1.2 Carrier Board
- - toradex,apalis_imx6q-eval # Apalis iMX6Q/D Module on Apalis Evaluation Board
+ - toradex,apalis_imx6q-eval # Apalis iMX6Q/D Module on Apalis Evaluation Board v1.0/v1.1
+ - toradex,apalis_imx6q-eval-v1.2 # Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2
- const: toradex,apalis_imx6q
- const: fsl,imx6q
--
2.43.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v2 2/2] arm: dts: nxp: imx: Add support for Apalis Evaluation Board v1.2
2024-01-24 14:13 [PATCH v2 0/2] nxp: imx: Add support for Apalis Evaluation Board v1.2 Hiago De Franco
2024-01-24 14:13 ` [PATCH v2 1/2] dt-bindings: arm: fsl: Add toradex,apalis_imx6q-eval-v1.2 board Hiago De Franco
@ 2024-01-24 14:13 ` Hiago De Franco
2024-02-06 7:40 ` [PATCH v2 0/2] " Shawn Guo
2 siblings, 0 replies; 4+ messages in thread
From: Hiago De Franco @ 2024-01-24 14:13 UTC (permalink / raw)
To: Shawn Guo, linux-arm-kernel
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, Hiago De Franco, Francesco Dolcini
From: Hiago De Franco <hiago.franco@toradex.com>
Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.
Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
---
v2:
- Add missing off-on-delay-us property with 100ms to reg_3v3_mmc and
reg_3v3_sd.
- Fix startup-delay-us property from 100us (reg_3v3_mmc and reg_3v3_sd)
and 1ms (reg_can1 and reg_can2) to 10ms.
- Fix pinctrl mux from 0xb000 to 0x1b0b0.
- Add Reviewed-by: Francesco Dolcini.
---
arch/arm/boot/dts/nxp/imx/Makefile | 1 +
.../dts/nxp/imx/imx6q-apalis-eval-v1.2.dts | 200 ++++++++++++++++++
.../boot/dts/nxp/imx/imx6q-apalis-eval.dts | 108 +---------
.../boot/dts/nxp/imx/imx6q-apalis-eval.dtsi | 120 +++++++++++
4 files changed, 323 insertions(+), 106 deletions(-)
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
create mode 100644 arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..0473f9b86ec7 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -147,6 +147,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-yapp4-phoenix.dtb \
imx6dl-yapp4-ursa.dtb \
imx6q-apalis-eval.dtb \
+ imx6q-apalis-eval-v1.2.dtb \
imx6q-apalis-ixora.dtb \
imx6q-apalis-ixora-v1.1.dtb \
imx6q-apalis-ixora-v1.2.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
new file mode 100644
index 000000000000..15d4a98ee976
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dtsi"
+
+/ {
+ model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2";
+ compatible = "toradex,apalis_imx6q-eval-v1.2", "toradex,apalis_imx6q",
+ "fsl,imx6q";
+
+ reg_3v3_mmc: regulator-3v3-mmc {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+ off-on-delay-us = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_mmc>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_MMC";
+ startup-delay-us = <10000>;
+ };
+
+ reg_3v3_sd: regulator-3v3-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ off-on-delay-us = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_3v3_sd>;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_SD";
+ startup-delay-us = <10000>;
+ };
+
+ reg_can1: regulator-can1 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can1_power>;
+ regulator-name = "5V_SW_CAN1";
+ startup-delay-us = <10000>;
+ };
+
+ reg_can2: regulator-can2 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enable_can2_power>;
+ regulator-name = "5V_SW_CAN2";
+ startup-delay-us = <10000>;
+ };
+
+ sound-carrier {
+ compatible = "simple-audio-card";
+ simple-audio-card,bitclock-master = <&codec_dai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&codec_dai>;
+ simple-audio-card,name = "apalis-nau8822";
+ simple-audio-card,routing =
+ "Headphones", "LHP",
+ "Headphones", "RHP",
+ "Speaker", "LSPK",
+ "Speaker", "RSPK",
+ "Line Out", "AUXOUT1",
+ "Line Out", "AUXOUT2",
+ "LAUX", "Line In",
+ "RAUX", "Line In",
+ "LMICP", "Mic In",
+ "RMICP", "Mic In";
+ simple-audio-card,widgets =
+ "Headphones", "Headphones",
+ "Line Out", "Line Out",
+ "Speaker", "Speaker",
+ "Microphone", "Mic In",
+ "Line", "Line In";
+
+ codec_dai: simple-audio-card,codec {
+ sound-dai = <&nau8822_1a>;
+ system-clock-frequency = <12288000>;
+ };
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi2>;
+ };
+ };
+};
+
+&can1 {
+ xceiver-supply = <®_can1>;
+ status = "okay";
+};
+
+&can2 {
+ xceiver-supply = <®_can2>;
+ status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 */
+&i2c1 {
+ /* Audio Codec */
+ nau8822_1a: audio-codec@1a {
+ compatible = "nuvoton,nau8822";
+ reg = <0x1a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_nau8822>;
+ #sound-dai-cells = <0>;
+ };
+
+ /* Current measurement into module VCC */
+ hwmon@40 {
+ compatible = "ti,ina219";
+ reg = <0x40>;
+ shunt-resistor = <5000>;
+ };
+
+ /* Temperature Sensor */
+ temperature-sensor@4f {
+ compatible = "ti,tmp75c";
+ reg = <0x4f>;
+ };
+
+ /* EEPROM */
+ eeprom@57 {
+ compatible = "st,24c02", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ size = <256>;
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+ bus-width = <4>;
+ pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+ vmmc-supply = <®_3v3_mmc>;
+ status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+ cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+ vmmc-supply = <®_3v3_sd>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_enable_3v3_mmc: enable3v3mmcgrp {
+ fsl,pins = <
+ /* MMC1_PWR_CTRL */
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+ >;
+ };
+
+ pinctrl_enable_3v3_sd: enable3v3sdgrp {
+ fsl,pins = <
+ /* SD1_PWR_CTRL */
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_enable_can1_power: enablecan1powergrp {
+ fsl,pins = <
+ /* CAN1_PWR_EN */
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ >;
+ };
+
+ pinctrl_enable_can2_power: enablecan2powergrp {
+ fsl,pins = <
+ /* CAN2_PWR_EN */
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_nau8822: nau8822grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT17__AUD5_TXD 0x130b0
+ MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x130b0
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
index 3fc079dfd61e..e1077e2da5f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@@ -7,29 +7,13 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
+#include "imx6q-apalis-eval.dtsi"
/ {
model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
"fsl,imx6q";
- aliases {
- i2c0 = &i2c1;
- i2c1 = &i2c3;
- i2c2 = &i2c2;
- rtc0 = &rtc_i2c;
- rtc1 = &snvs_rtc;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
reg_pcie_switch: regulator-pcie-switch {
compatible = "regulator-fixed";
enable-active-high;
@@ -40,14 +24,6 @@ reg_pcie_switch: regulator-pcie-switch {
startup-delay-us = <100000>;
status = "okay";
};
-
- reg_3v3_sw: regulator-3v3-sw {
- compatible = "regulator-fixed";
- regulator-always-on;
- regulator-max-microvolt = <3300000>;
- regulator-min-microvolt = <3300000>;
- regulator-name = "3.3V_SW";
- };
};
&can1 {
@@ -62,102 +38,22 @@ &can2 {
/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
&i2c1 {
- status = "okay";
-
+ /* PCIe Switch */
pcie-switch@58 {
compatible = "plx,pex8605";
reg = <0x58>;
};
-
- /* M41T0M6 real time clock on carrier board */
- rtc_i2c: rtc@68 {
- compatible = "st,m41t0";
- reg = <0x68>;
- };
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
- status = "okay";
};
&pcie {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reset_moci>;
- /* active-high meaning opposite of regular PERST# active-low polarity */
- reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
- reset-gpio-active-high;
vpcie-supply = <®_pcie_switch>;
status = "okay";
};
-&pwm1 {
- status = "okay";
-};
-
-&pwm2 {
- status = "okay";
-};
-
-&pwm3 {
- status = "okay";
-};
-
-&pwm4 {
- status = "okay";
-};
-
-®_usb_host_vbus {
- status = "okay";
-};
-
-®_usb_otg_vbus {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
&sound_spdif {
status = "okay";
};
-&spdif {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
-&uart2 {
- status = "okay";
-};
-
-&uart4 {
- status = "okay";
-};
-
-&uart5 {
- status = "okay";
-};
-
-&usbh1 {
- disable-over-current;
- vbus-supply = <®_usb_host_vbus>;
- status = "okay";
-};
-
-&usbotg {
- disable-over-current;
- vbus-supply = <®_usb_otg_vbus>;
- status = "okay";
-};
-
/* MMC1 */
&usdhc1 {
status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
new file mode 100644
index 000000000000..b6c45ad3f430
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2024 Toradex
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+ aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c3;
+ i2c2 = &i2c2;
+ rtc0 = &rtc_i2c;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_3v3_sw: regulator-3v3-sw {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "3.3V_SW";
+ };
+};
+
+&i2c1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ /* M41T0M6 real time clock on carrier board */
+ rtc_i2c: rtc@68 {
+ compatible = "st,m41t0";
+ reg = <0x68>;
+ };
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_moci>;
+ /* active-high meaning opposite of regular PERST# active-low polarity */
+ reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpio-active-high;
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&pwm4 {
+ status = "okay";
+};
+
+®_usb_host_vbus {
+ status = "okay";
+};
+
+®_usb_otg_vbus {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&spdif {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&usbh1 {
+ disable-over-current;
+ vbus-supply = <®_usb_host_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ disable-over-current;
+ vbus-supply = <®_usb_otg_vbus>;
+ status = "okay";
+};
--
2.43.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 4+ messages in thread