From: Stanislav Jakubek <stano.jakubek@gmail.com>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
phone-devel@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH] ARM: dts: qcom: motorola-falcon: add accelerometer, magnetometer
Date: Sun, 9 Jun 2024 13:05:43 +0200 [thread overview]
Message-ID: <ZmWMh6fuLasvGkR/@standask-GA-A55M-S2HP> (raw)
Add the accelerometer and magnetometer that are present on the Motorola
Moto G (2013) device.
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
---
.../boot/dts/qcom/msm8226-motorola-falcon.dts | 53 +++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
index 029e1b1659c9..5dbca83f2230 100644
--- a/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
+++ b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
@@ -96,6 +96,35 @@ reserved@fb00000 {
};
};
+&blsp1_i2c2 {
+ status = "okay";
+
+ magnetometer@c {
+ compatible = "asahi-kasei,ak8963";
+ reg = <0xc>;
+ interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&pm8226_l19>;
+ vid-supply = <&pm8226_lvs1>;
+ pinctrl-0 = <&mag_int_default &mag_reset_default>;
+ pinctrl-names = "default";
+ };
+
+ accelerometer@19 {
+ compatible = "st,lis3dh-accel";
+ reg = <0x19>;
+ interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8226_l19>;
+ vddio-supply = <&pm8226_lvs1>;
+ pinctrl-0 = <&accel_int_default>;
+ pinctrl-names = "default";
+ mount-matrix = "0", "1", "0",
+ "1", "0", "0",
+ "0", "0", "-1";
+ st,drdy-int-pin = <1>;
+ };
+};
+
&blsp1_i2c3 {
status = "okay";
@@ -321,6 +350,30 @@ &smbb {
};
&tlmm {
+ accel_int_default: accel-int-default-state {
+ pins = "gpio63";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-disable;
+ };
+
+ mag_int_default: mag-int-default-state {
+ pins = "gpio66";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-disable;
+ };
+
+ mag_reset_default: mag-reset-default-state {
+ pins = "gpio62";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+
reg_lcd_default: reg-lcd-default-state {
pins = "gpio31", "gpio33";
function = "gpio";
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2024-06-09 11:06 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-06-09 11:05 Stanislav Jakubek [this message]
2024-06-13 7:48 ` [PATCH] ARM: dts: qcom: motorola-falcon: add accelerometer, magnetometer Konrad Dybcio
2024-06-13 17:18 ` Stanislav Jakubek
2024-06-13 17:20 ` Konrad Dybcio
2024-06-14 22:48 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=ZmWMh6fuLasvGkR/@standask-GA-A55M-S2HP \
--to=stano.jakubek@gmail.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=phone-devel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox