From: Frank Li <Frank.li@nxp.com>
To: Richard Zhu <hongxing.zhu@nxp.com>
Cc: robh@kernel.org, krzk+dt@kernel.org, conor+dt@kernel.org,
shawnguo@kernel.org, l.stach@pengutronix.de,
devicetree@vger.kernel.org, linux-pci@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, kernel@pengutronix.de,
imx@lists.linux.dev
Subject: Re: [PATCH v5 1/5] dt-bindings: ata: Add i.MX8QM AHCI compatible string
Date: Fri, 2 Aug 2024 16:39:56 -0400 [thread overview]
Message-ID: <Zq1EHGXx7yAK9TXS@lizhi-Precision-Tower-5810> (raw)
In-Reply-To: <1722581213-15221-2-git-send-email-hongxing.zhu@nxp.com>
On Fri, Aug 02, 2024 at 02:46:49PM +0800, Richard Zhu wrote:
> Add i.MX8QM AHCI "fsl,imx8qm-ahci" compatible strings.
>
> i.MX8QM AHCI SATA doesn't require AHB clock rate to set the vendor
> specified TIMER1MS register. ahb clock is not required by i.MX8QM AHCI.
>
> Update the description of clocks in the dt-binding accordingly.
>
> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
> ---
> .../devicetree/bindings/ata/imx-sata.yaml | 47 +++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/ata/imx-sata.yaml b/Documentation/devicetree/bindings/ata/imx-sata.yaml
> index 68ffb97ddc9b2..f4eb3550a0960 100644
> --- a/Documentation/devicetree/bindings/ata/imx-sata.yaml
> +++ b/Documentation/devicetree/bindings/ata/imx-sata.yaml
> @@ -19,6 +19,7 @@ properties:
> - fsl,imx53-ahci
> - fsl,imx6q-ahci
> - fsl,imx6qp-ahci
> + - fsl,imx8qm-ahci
>
> reg:
> maxItems: 1
> @@ -27,12 +28,14 @@ properties:
> maxItems: 1
>
> clocks:
> + minItems: 2
> items:
> - description: sata clock
> - description: sata reference clock
> - description: ahb clock
>
> clock-names:
> + minItems: 2
> items:
> - const: sata
> - const: sata_ref
> @@ -58,6 +61,25 @@ properties:
> $ref: /schemas/types.yaml#/definitions/flag
> description: if present, disable spread-spectrum clocking on the SATA link.
>
> + phys:
> + items:
> + - description: phandle to SATA PHY.
> + Since "REXT" pin is only present for first lane of i.MX8QM PHY, it's
> + calibration result will be stored, passed through second lane, and
> + shared with all three lanes PHY. The first two lanes PHY are used as
> + calibration PHYs, although only the third lane PHY is used by SATA.
> + - description: phandle to the first lane PHY of i.MX8QM.
> + - description: phandle to the second lane PHY of i.MX8QM.
> +
> + phy-names:
> + items:
> + - const: sata-phy
> + - const: cali-phy0
> + - const: cali-phy1
> +
> + power-domains:
> + maxItems: 1
> +
> required:
> - compatible
> - reg
> @@ -65,6 +87,31 @@ required:
> - clocks
> - clock-names
>
> +allOf:
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - fsl,imx53-ahci
> + - fsl,imx6q-ahci
> + - fsl,imx6qp-ahci
> + then:
> + properties:
> + clock-names:
> + minItems: 3
> +
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - fsl,imx8qm-ahci
> + then:
> + properties:
> + clock-names:
> + minItems: 2
> +
> additionalProperties: false
>
> examples:
> --
> 2.37.1
>
next prev parent reply other threads:[~2024-08-02 20:41 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-08-02 6:46 [PATCH v5 0/5] Refine i.MX8QM SATA based on generic PHY callbacks Richard Zhu
2024-08-02 6:46 ` [PATCH v5 1/5] dt-bindings: ata: Add i.MX8QM AHCI compatible string Richard Zhu
2024-08-02 20:39 ` Frank Li [this message]
2024-08-02 6:46 ` [PATCH v5 2/5] ata: ahci_imx: Clean up code by using i.MX8Q HSIO PHY driver Richard Zhu
2024-08-02 20:40 ` Frank Li
2024-08-02 6:46 ` [PATCH v5 3/5] ata: ahci_imx: AHB clock rate setting is not required on i.MX8QM AHCI SATA Richard Zhu
2024-08-02 20:44 ` Frank Li
2024-08-02 6:46 ` [PATCH v5 4/5] ata: ahci_imx: Enlarge RX water mark for i.MX8QM SATA Richard Zhu
2024-08-02 20:46 ` Frank Li
2024-08-05 2:56 ` Hongxing Zhu
2024-08-02 6:46 ` [PATCH v5 5/5] ata: ahci_imx: Correct the email address Richard Zhu
2024-08-02 20:46 ` Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Zq1EHGXx7yAK9TXS@lizhi-Precision-Tower-5810 \
--to=frank.li@nxp.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=hongxing.zhu@nxp.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=l.stach@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=robh@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox