Re: [PATCH v3 3/5] clk: imx: fracn-gppll: fix pll power up

[Abel Vesa <abel.vesa@linaro.org>]

On 24-10-27 20:00:09, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan@nxp.com>
> 
> To i.MX93 which features dual Cortex-A55 cores and DSU, when using
> writel_relaxed to write value to PLL registers, the value might be
> buffered. To make sure the value has been written into the hardware,
> using readl to read back the register could achieve the goal.
> 
> current PLL power up flow can be simplified as below:
>   1. writel_relaxed to set the PLL POWERUP bit;
>   2. readl_poll_timeout to check the PLL lock bit:
>      a). timeout = ktime_add_us(ktime_get(), timeout_us);
>      b). readl the pll the lock reg;
>      c). check if the pll lock bit ready
>      d). check if timeout
> 
> But in some corner cases, both the write in step 1 and read in
> step 2 will be blocked by other bus transaction in the SoC for a
> long time, saying the value into real hardware is just before step b).
> That means the timeout counting has begins for quite sometime since
> step a), but value still not written into real hardware until bus
> released just at a point before step b).
> 
> Then there maybe chances that the pll lock bit is not ready
> when readl done but the timeout happens. readl_poll_timeout will
> err return due to timeout. To avoid such unexpected failure,
> read back the reg to make sure the write has been done in HW
> reg.
> 
> So use readl after writel_relaxed to fix the issue.
> 
> Since we are here, to avoid udelay to run before writel_relaxed, use
> readl before udelay.
> 
> Fixes: 1b26cb8a77a4 ("clk: imx: support fracn gppll")
> Co-developed-by: Jacky Bai <ping.bai@nxp.com>
> Signed-off-by: Jacky Bai <ping.bai@nxp.com>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>

Reviewed-by: Abel Vesa <abel.vesa@linaro.org>

> ---
>  drivers/clk/imx/clk-fracn-gppll.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/clk/imx/clk-fracn-gppll.c b/drivers/clk/imx/clk-fracn-gppll.c
> index 4749c3e0b7051cf53876664808aa28742f6861f7..85771afd4698ae6a0d8a7e82193301e187049255 100644
> --- a/drivers/clk/imx/clk-fracn-gppll.c
> +++ b/drivers/clk/imx/clk-fracn-gppll.c
> @@ -254,9 +254,11 @@ static int clk_fracn_gppll_set_rate(struct clk_hw *hw, unsigned long drate,
>  	pll_div = FIELD_PREP(PLL_RDIV_MASK, rate->rdiv) | rate->odiv |
>  		FIELD_PREP(PLL_MFI_MASK, rate->mfi);
>  	writel_relaxed(pll_div, pll->base + PLL_DIV);
> +	readl(pll->base + PLL_DIV);
>  	if (pll->flags & CLK_FRACN_GPPLL_FRACN) {
>  		writel_relaxed(rate->mfd, pll->base + PLL_DENOMINATOR);
>  		writel_relaxed(FIELD_PREP(PLL_MFN_MASK, rate->mfn), pll->base + PLL_NUMERATOR);
> +		readl(pll->base + PLL_NUMERATOR);
>  	}
>  
>  	/* Wait for 5us according to fracn mode pll doc */
> @@ -265,6 +267,7 @@ static int clk_fracn_gppll_set_rate(struct clk_hw *hw, unsigned long drate,
>  	/* Enable Powerup */
>  	tmp |= POWERUP_MASK;
>  	writel_relaxed(tmp, pll->base + PLL_CTRL);
> +	readl(pll->base + PLL_CTRL);
>  
>  	/* Wait Lock */
>  	ret = clk_fracn_gppll_wait_lock(pll);
> @@ -302,6 +305,7 @@ static int clk_fracn_gppll_prepare(struct clk_hw *hw)
>  
>  	val |= POWERUP_MASK;
>  	writel_relaxed(val, pll->base + PLL_CTRL);
> +	readl(pll->base + PLL_CTRL);
>  
>  	ret = clk_fracn_gppll_wait_lock(pll);
>  	if (ret)
> 
> -- 
> 2.37.1
>